Time Machine is base station and trying to configure two airport express
I have a time capsule as my base station and am trying to re-connect my (2) airport express devices as additional wireless sources. The (3) used to work in harmony, now the two airport express just flash amber and I can't reconnect. Can anyone help - i have read support documentation, but just can't seem to get the 2 to sync with the time capsule base station. Many thanks
Guys,
I agree with Don. This was my experience, and a brief description of my network... hope it helps.
The network has the following: ADSL Router... attached via ethernet to Airport with antenna. At this location is also an AE. Another Aiport with Antenna, that then has a Cisco Linksys WRT 54G. For reference, I use a PC and Laptop at the AE end and various Mac's at the other.
So to the point... I added the Linksys just before the AE. It took three days. There is an awful lot about the Linksys on the net, and for me..... which is not a suggestion, I added extra firmware. Either way, using Safari, I manually set up the router. There are about five pages that I found important..... I may be missing some, basically the DHCP on mine needed to be switched off. Once it recognised the rest of the network, via manual IP address and using a unique name, for a while I had both networks working side by side, .... because of where it was I didn't need to setup any of the ADSL modem side (its effectively a WDS relat base station in Airport terms) but that page is straight forward. Good idea to have it password protected and to change the IP, apparently. Anyway, the AE took longer to get working, and I believe that this was the result of a closely added firmware update as well.... ie, it took me about 4 times to get it to accept the update completely, and that had to be done with it attached via ethernet. The basic setup of this was straight forward after that just using the software.
Hope this helps.
G5,iBook SE, iMac Bondi, iBook G4,
Similar Messages
-
I have an aiport extreme base station in my living room and an airport express in my bedroom extending the network. For some reason my xbox along with some other devices always connects to the extreme base station in the living room which has a very low signal. Is there a way to setup a seperate network for my express extender so that I can connect only certain devices? HELP
You would probably want your Express to join the network if an extender isn't required. Reset to factory settings and join the network.
If you do want your Express as an extender run an Ethernet cable between the Express and the Verizon router and set the Express up to be in bridge mode, with the same WiFi network name and password as your Verizon router. -
I have my Time Machine on an external drive (not connected to Airport Extreme) and I have an external HD attached to airport extreme. Is it possible to have Time Machine backUp computer HD AND external HD connected to Airport Extreme. How?
Is it possible to have Time Machine backUp computer HD AND external HD connected to Airport Extreme.
Sorry, but no.
Time Machine will backup your Mac, but not the hard drive attached to the AirPort Extreme.
Time Machine will back up a hard drive only if it is attached directly to your Mac via USB or FireWire. -
How to set Time capsule as base station and airport express to join
I have a wireless network using an Airport express. Now I would like to have time capsule to be set up as the base station and just the airport express to join this network, in order to listen wirelessly to music, but keep the speed of the time capsule.
Right now, the ethernet cable is connected to the Airport express. Do I have to switch that to the Time capsule? I tried to do that, but it wasn't able to connect to the internet in this case.... I am lost. Now I have a speedy time capsule, but have the network running on the slow Airport express... Please help!!! And I believe as you guessed already, I am not a smarty, when it comes to networks.
HELP! Please!!I actually have mine set up this way that you are looking to do. Works well for me. here si what you can try:
Make sure you unplug the Express all together first. It does interfere when trying to set this up. Next setup your TC just like the instruction says (remember no Express). You should just be able to set up your TC, connect to the internet and get going like any other router or like the Airport Extreme. if you set up your TC with your comp and CANNOT access the internet that is your first problem. My suggestion: do a hard reset of the TC if you have already attached it to the Express while also doing a hard reset of the Express - this is to bring them both back to afctory defaults to start fresh. This definitaely helped me.
So once you have your TC up and running and you have internet access thru your TC, you are halfway there. Make sure your TC shows in the left column of the Airport Utility (and dont forget to install the Airport Utility from the disc that comes with teh TC before you do any of this, forgot that). if it shows up in the left column you should also be able to see the Express in that column, both with green lights, if you have set this up correctly. Then plug in the Express. As the above mentioned remember t make sure it is connected to the correct port on that back of the TC. It will remain amber then blink a few times. This is normal. It should be blinking amber when you attempt the setup of the Express. Your airport utility shoul dnow see the addt base station (Express) in the left column. When you click on it and click CONTINUE it will ask you if you want to switch networks. You can do that and lick switch provided you are already connected to the TC and alrady have an internet connection. Once you click switch the TC will disappear from the left column and you will be left only with the Express. This is OK. I am not in fron to fm y comp right now so I am doing this from memory but in setting up the Express you want to add it to your existing network. You will have to choose which network to add it to in a drop down box in one of those steps - just make sure you add it to the one that you named your TC. Then click to the finish and click UPDATE. Let it finish the update - you shoul dsee green light son both the TC and Extreme HARDWARE - not necessarily in the airport utility. Also it is a good idea to to to the menu bar on top where the WiFi icon is and manually select your network in case you get bumped off while the TC is updating itself after you ckicl update - this happened ot me and it wouldnt complete the update and took me forever to figure out it needs internet connection to complete the update screen.
next make sure you RESTART your comp. This I guess will make all changes basically go into effect as you cycle it up. When you are up and running you should see your WiFi connect as your TC and NOT your Express. Also go back into airport utility and see if you ahve both items listed in left column - they too should have a greenlight. If they do you should be set.
I did this because I wanted to steam my iTunes files that I have on my TC to stream to iTunes via my network. The Express part, as you know, is what allows the streaming. So make sure you plug your stereo cable into the Express audio port. Then go to iTunes and on the bottom you will notice a new little drop down box - make sure to select Express so it can wireless stream (in iTunes prefs there is a pref you must turn on also to allow iTunes to see remote speakers.
Ive simplified this a little since I am not at home but this is the gist. In a prefect worl you should be able to easily have this work. I did so I know it does at least work if not anything else. You just have to make sure you get the steps correct and have everyhing plugge din where they should be...
G'luck -
Hi I have an airport extreme base station And trying to dial on windows
Ok I have a airport extreme base station the one with dial-up modem and power over ethernet. Well i have people PC as my provider, and can dial the connection on my macbook by using internet connect. but on my hp i can not. I have tried to create a connection type on it and cant figure out how to have it connect like on internet connect. tho i can go the admin utility and click automatically connect and click OK and it dials the connection to disconnect i re click it and click OK and it disconnects but i do not like it that way. So what am i to do and is their a internet connect app for windows. I have also contacted apple and hp and that did not help. Feedback welcome and is needed.
Thanks to all that leave feedbackIf you are using dial-up.
Jon Sevy has a Java Utility for this purpose.
You will need Java in order to run the utility
http://www.java.com -
Trying to configure an AirPort Express as a WDS on a complicated network
Hey All,
I purchased an AirPort Express to try and re-route the signal to increase range. My current AirPort Extreme base station had a very complicated setup. It's a hidden network and it has an attached Linksys router, and some combination of those factors seems to have prevented me from setting up the Extreme as a WDS. In AirPort Setup Assistant, my network cannot be selected because it's hidden, and I can't find anything to help me in AirPort Admin Utility.
Can anyone help me please? This is very important.
Thanks in advance!Guys,
I agree with Don. This was my experience, and a brief description of my network... hope it helps.
The network has the following: ADSL Router... attached via ethernet to Airport with antenna. At this location is also an AE. Another Aiport with Antenna, that then has a Cisco Linksys WRT 54G. For reference, I use a PC and Laptop at the AE end and various Mac's at the other.
So to the point... I added the Linksys just before the AE. It took three days. There is an awful lot about the Linksys on the net, and for me..... which is not a suggestion, I added extra firmware. Either way, using Safari, I manually set up the router. There are about five pages that I found important..... I may be missing some, basically the DHCP on mine needed to be switched off. Once it recognised the rest of the network, via manual IP address and using a unique name, for a while I had both networks working side by side, .... because of where it was I didn't need to setup any of the ADSL modem side (its effectively a WDS relat base station in Airport terms) but that page is straight forward. Good idea to have it password protected and to change the IP, apparently. Anyway, the AE took longer to get working, and I believe that this was the result of a closely added firmware update as well.... ie, it took me about 4 times to get it to accept the update completely, and that had to be done with it attached via ethernet. The basic setup of this was straight forward after that just using the software.
Hope this helps.
G5,iBook SE, iMac Bondi, iBook G4, -
Ows the meaning of failure code 4 showed while I tried to link to airport express?
What is the meaning of failurecode 4 showed after Itried to conect to my airport express?
Knowing that error code 4 is a connection failure will likely not tell you much...if anything...more than you already know.
Can you provide some more details on how you are trying to configure the AirPort Express?
What service will it perform on your network?
What type of computer are you using?
What operating system is the computer using? -
trying to reconnect airport express to time machine but express not showing up in base station. unfortunately clicked forgot in airport utility and express no longer shows up. how to reconnect?
I would recommend setting the wireless encryption on the AirPort Express BEFORE configuring it for the AirPort Extreme in this case. This issue also comes up often when configuring AirPorts into a WDS.
If setting up security in my recommend order does not work, temporarily connect the Express by Ethernet to the Extreme; make the security changes, and then, move the Express back to the desired location. -
I am trying to connect a NetGear Wifi Range Extender to my existing Wifi. I have an Airport Extreme Base Station and I am also connected to a Vonage Phone Router. Any help would be appreciated?
The Apple update Firmware for my Airport Extreme Base Station does not update for some reason? Help?
Additionally, I have an older version Airport Express that does not update with the newer Airport Utility Version 6.3 and asks me to download 5.6 to update? Is this worth it?
ThanksThe netgear is not going to work very well.. and not at all unless it is universal wireless extender.. you cannot use WDS method.
If it does support universal wireless then make sure the airport uses a rational SMB compatible wireless name.. not an apple name which is 35 characters long with spaces and illegal characters like apostrophe.
So nice AE name.. AEwifi and actually while you are trying.. fruitlessly to do this.. use AE24ghz and AE5ghz (so different names on the different bands)
Assuming your AE is gen3 or greater.
You should also fix the wireless channel at least for 2.4ghz since the netgear is probably only going to repeat 2.4ghz so use channel 11, as a trial.
And use no wireless security as a test.. if that works.. then use WPA1 & 2.. as often old equipment using WPA2 is not compatible.
If it fails with simple name.. fixed channel and no security. Sorry it is not compatible at all.. it happens.
If your AE is G wireless or earlier model.. really the time has come for replacement.
If your Express is G wireless model it is not supported.. and is too old to bother with expect I guess if you want to run audio to a speaker.
You must use older 5.6 utility to do this.. so do you have a computer running older OS.. up to Mountain Lion it is easy to install with a bit of manipulation.. later is much harder .. or windows computer anywhere or available to you. -
Trying to set up airport express to extend my Wi-Fi network. Primary base station is a time capsule. Tried searching for airport express using Wi-Fi status, no luck. Even tried plugging airport express into iMac, still no luck. Airport express showing solid amber light. Thanks for any help.
Airport express showing solid amber light
Unfortunately, this can mean one of two things:
1) The Express is locked up and will need a Factory Default Reset procedure to try to return the device back to its original default settings so that it can be reconfigured again.
2) The Express is defective. If you cannot get the Express back to a slow, blinking amber light after a Factory Default Reset, the Express will need to be replaced.
Try the Factory Default Reset a few times and report back on your progress.
Resetting an AirPort Base Station or Time Capsule FAQ -
since latest update to airport extreme im getting 10 unknown base stations and time caps showing up as though they are a part of my network. sometimes i can "forget" them and they will disappear initially but soon return. i need and want only my connection inside my home . any ideas. i have done a factory reset and set up a new network but they continue to show up.
I'm not convinced that the problem lies in Airport Utility. This same thing was happening to me, nearly exactly as you describe it. The thing is that with me, the problems clearly started when I updated the firmware in my Airport Express (n). That's when all the wacky stuff started happening. Sometimes it would show up in AU, sometimes it didn't and even if it didn't, I could still access the internet through it.
But as you said, the problems got really bad when another Express (b/g) was put on the network with it. Even when it did work, the (b/g) would make it impossibly slow.
You know more about this than me, and clearly have more patience if you've restarted the network fifty times. I gave up at about ten.
In any case, your solution is more of a work around and if you're still having that slow connection problem, I'm not sure you've got it. But thanks for your reporting of this. At least I know I'm not crazy. -
I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?
apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together. -
I havea "wirelessly challenged" 2-story home and need to extend the range. Currently I have an 802.11n Main Base Station with an 802.11n Airport Express Remote. It's not getting the job done (upstairs connection is weak).
I am considering getting an 802.11ac Airport Time Capsule to help, even though I currently only have devices with 802.11n wireless connectivity (future-proof a little).
I an planning on setting up a Wireless Distribution System (WDS) Network:
1.) Setting up the Time Capsule as the Main Base Station connected to a Cable modem
2.) Reconfiguring and Setting up the current AirPort Extreme 802.11n as a Relay Base Station
3.) Reconfiguring and Setting up the current AirPort Express 802.11n as a Remote Station
I cannot "hard wire" one Base Statio to the other.
Will this work?Will this work?
Unfortunately, no. WDS is a older, very inefficient way to extend the wireless network signal.
As such, newer operating systems like Lion, Mountain Lion and Mavericks do not even offer settings for this older WDS type of network.
In addition, the new Time Capsule has no capabilities to use WDS settings at all, even if you used a Mac with another operating system to try to set things up.
Even if it were possible to set up a WDS network, the speed on the network would be incredibly slow. As you know, WDS only operates at "g" wireless speed levels. Each "relay" or "remote" that you add to the network each cuts that bandwidth or speed in half.
With a WDS "main", "relay" and "remote", the network would be operating at about 14 Mbps......a tiny fraction of what the devices would be capable of providing normally. -
Airport Express Base Station and HP Laserjet 1020 printer connected
Dear all,
I have a Laptop (PC) Sony Vaio PCG-Z1XSP and an Airport Express Base Station which work perfectly together (internet access and I-tunes). I recently bought a printer HP Laserjet 1020 and connected it to the Airport Express USB soket. I managed to make it work and print a couple of times, but as soon as I turn off the printer or the computer or Airport Express, the next time I want to print, it doesn't work anymore.
The Airport Admin Utility recognises the printer (I can see it listed). I have updated the Airport Express software to the Firmware version 6.3 as well as downloaded the latest driver available on HP's website for my printer. I've also substituted the USB cable. Can anybody help me here? Thank you very much and best regards.Hallo everybody,
Thanks for all the answers. I have contacted HP's chat online and gone through the problem with 3 different technicians. I've tried a lot myself too. The issue was partially solved by restarting the printer spooler, i.e. stop, then start and then restart it.
However after I was so happy that the printer worked, I turn off everything. When I turn on again, it was not working anymore. Then I tried to see by exclusion what the problem is, I had to restart the Hardwar I don't know how many times.
Conclusion:
1. The USB cable must be plugged into the airport express before turning on anything.
2. Turn on the printer first.
3. Turn on the airport express and the computer.
4. If you try to print it doesn't work, even if you reset the airport express through the airport express utility software. The printer is recognized and appears in it though.
5. Disconnect the USB cable from the airport express and connect it to the PC directly.
6. Print a document.
7. Disconnect the cable and reconnect it to the airport express.
8. Now you should be able to print wireless. You may need to reset the airport expresst with the utility softwar, but I managed to print without having to do it.
9. The pörinter works even if you turn off and on again the computer, or you suspend the windows session and restart it, or if you put it in standby and restart it.
10. The printer works even if you turn off the airport express and the computer, or the airport express alone and restart them/it.
11. The printer doens't work anymore if you turn it off and onn again. In such a case you have to plug in/out as discribeb above.
Solution: Leave the printer always on, or make the plug in/out every morning when you start the computer and print one page direclty before being able to print wireless.
Does anybody have a solution to this problem? I mean it prints, but it is annoying to plug in/out every day, no?
HP's technician says that it is not a recommanded solution the HP Laserjet 1020 with the airport express, since the printer works on a host based server basis... I mean it is easy to say that, but one expects to buy a printer that works always and not to have to plug in/out everyday, restart spooler and so on.
Can anybody comment or suggest anything I can do to avoid this? Thank you and I hope this helps others too. -
Serious problem with base station and/or computer internet connection
Hi,
my powerbook does not detect my base station (another computer at home does, so the base station seems to be working) but it does detect other networks.
I have allready tried to reset the basse station (many times) but it doesen't help. Have tried to re-configure in Airport Admin Utility there is no base station (I cannot push configure) - when I push "Other" - it does not accept the base station password (have also tried "public" as they suggest in "help").
The same thing happens in Airport Setup Assistant: it does not detect my base station. It has happened before that the base station "disapears" and I could fix it now it seems to be unfixable. Can anyone out there help me???Agnes,
the one computer connects wirelessly to the base
station and
works alright? Also the Mac can connect to the
base
station with ethernet and works alright?
Yes, thats correct
Then you should be able to access the base station two ways, from the Mac via ethernet or from the pc. I am assuming that your "pc at home" is a pc running windows (if the 2nd computer is also a Mac it would be even better).
Anyway, you can administer the base station from the dark side, you may want to check out the following:
AirPort 4.2 for Windows
http://www.apple.com/support/downloads/airport42forwindows.html
Check also:
XP users need to have WZC installed to administer:
http://docs.info.apple.com/article.html?artnum=108049
If you haven't upgraded your pc to XP Service Pack 2.
As far as running the admin utility from the Mac, connect to the base via ethernet. You have indicated that you can do that and get to the internet, therefore you should be able to see the base station with the admin utility. If you are seeing your neigbor's that is wirelessly. But the wired connection Mac->Ethernet->Base-LAN-Port should allow the base to show up with a Name and an IP Adress.
Once in the admin utility for the base station (either by pc wirelessly or by Mac via ethernet) you can then make changes. You should be able to see the Base Station Name and the Airport network name. You can then change the channel: 1, 4, 7, 11 (try three apart from each other). Is your base set up to configure TCP/IP using ethernet, configure using DHCP (select the Internet tab at the top to get to this page)? On the Network tab page, is the base configured to Distribute IP addresses, Sharing a single IP address using DHCP and NAT?
As far as your Mac's System Network Preferences, you are not selected to Connect using PPoE are you? Are you set to "Automatically join an open network"? Are you configured for Using DHCP? To join a specific network (your airport network name and password)?
By the way, if RF interference is a possible problem, you can check out:
AirPort: Potential sources of interference
http://docs.info.apple.com/article.html?artnum=58543
Gino
-
Maybe you are looking for
-
Hello! I installed Archlinux and I got to the part where I am installing sound and video and other goodies like that. I just rebooted and logged in and it said this: -- taylor: /home/taylor: change directory failed: No suh file or directory Logging i
-
Version 3.1.3 screwed my ipod and it's freezing freezes
Ok so I updated to version 3.1.3 and the update process failed and got an error (9). So I resumed the update from another PC. After successful 5th attempt to update to version 3.1.3 I was playing with the apps on my ipod touch and the apps freeze. I
-
Problems with B2B Editor validating HL7 Messages
Hi all, I am having some problems related to B2B Document Editor and HL7 messages. When we ran the Analyzer with the following document: MSH|^~\&|ALERT|CHVNG|CPCHS|CHVNG|20070409145826+0000||OMG^O19^OMG_O19|1|P|2.4| PID|||303030^^^SONHO^NS||Patient^A
-
Can you find a converter that will take you monitor and plug it into a cable TV box? So that you can watch TV on your monitor?
-
Problem in mounting the repository
Hai expertise, When i try to mount repository or change database settings it is showing some error (The same thing is working previously) : 1) I have not saved the list of mounted servers SAP MDM Servers.mcs while closing the MDM console (