Time Machine no longer recognized - MacBook Pro

I am using a Western Digital 1TB MyBookWorld network hard drive. I upgraded the hard drive in my MacBook Pro from 250gig to 500 gig. When I tried to restore from Time Machine, my computer could no longer see the drive. I also use the drive to back up 3 pc laptops and they work fine.
Any suggestions?

hammer58 wrote:
During the initial setup for TM, there was one screen that required username wd_backup and password admin. Later I changed the username for the TM folder to garyham58 and a personal password. That is the username and password I am looking for.
As I understand it, the original name and password were supplied by WD and stored on the NAS. Any changes would have been stored on the NAS. And resetting it would have to be done via the NAS.
I would think that there is some way to reset TM and start from scratch
I fear you may have already done part of that, inadvertently, since the folder shows no contents.
But it's not a password for the Time Machine application; it's the sharing of the WD disk, which is done by WD. When you back up with Time Machine to a simple external HD, there is no password for the drive. When you back up over a network to a Time Capsule, or a USB drive connected to it, you set up the password, if any, via Airport Utility, and I believe that's stored by the router as well as in the keychain on your Mac.
Do you still have the original 250 GB HD? If so, your best bet may be to get an enclosure for it, from http://www.macsales.com/ or the like. You can put the HD into it and connect it to your Mac via USB or FireWire, and it will become a normal external HD. Then you can start up from it and "clone" the HD to the new one.
Then you might be able to re-establish contact with the WD, and see your backups, unless they got erased during all the problems, or erase it and start over.

Similar Messages

  • Imported old computer via time machine into new 2012 macbook pro, but its still running ilife 09 instead of 11?

    imported old computer via time machine into new 2012 macbook pro, but its still running ilife 09 instead of 11?

    I am assuming you had iLife 09 on the old computer - when you moved everything over, that came along with it.
    I also have older versions of iLife (on install disks) and just recently got a new 2012 Macbook Pro. I noticed that iMovie 11, iPhoto and Garageband (I think) are listed in my Mac App Store Purchases with a notation to "accept". So you might want to check MAS to see if the apps are sitting there.
    Now, I have chosen not to accept them for now for two reasons: I have iLife 11 on a disk and prefer that rather than having it tied to MAS/Apple ID and as long as I have my disk version installed, I also still have iDVD which I use a lot. I'm not sure if "accepting" those three from MAS would wipe out my iLife 11 installs including iDVD (which would be unacceptable for me). So, since I already have the latest version, I've opted to ignore the "accept" and, in fact, will leave it like that - if I ever sell this machine, the buyer can then accept them if they want with their own Apple ID. So before accepting the apps (if they are listed in MAS), you might want to check to make sure that your iLife install isn't wiped out - that is, if you have iDVD and want to keep it.

  • I recently did a full reinstall from my time machine and now my MacBook pro won't back up to the time machine. It starts a full backup ignoring the original back up, can anyone help?

    I recently did a full reinstall from my time machine and now my MacBook pro won't back up to the time machine. It starts a full backup ignoring the original back up, can anyone help?

    Did you follow the instructions on the page linked below?
    OS X Yosemite: Recover your entire system

  • How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!

    How can I get Time Machine to back up an external hard drive (iPhotos) that is attached to airport extreme base station. Note: Time machine is usb to macbook pro and external drive with iphotos is usb to airport extreme base station. Help please. Thanks!

    Once you have the drive connected to your Mac, click System Preferences (gear icon) on the dock
    Click Time Machine
    Click Options
    Be default, the hard drive will be Excluded from backups. Click the drive to highlight it, then click the "-" (minus) button at the bottom of the list to remove the drive from Excluded items.
    The drive will be backed up on the next Time Machine pass
    Everything above assumes that the hard drive has been formatted in Mac OS Extended (Journaled) as Time Machine will only backup drives in that format.

  • My Time machine won't back up.  Recently updated to OS x 10.7.5.  Error message is as follows:  "The backup disk image "/Volumes/Time Machine Backup/Scott's MacBook Pro.sparsebundle" is already in use."  What is wrong and how do I fix it?  Thanks.

    My Time machine won't back up.  Recently updated to OS x 10.7.5.  Error message is as follows:  "The backup disk image “/Volumes/Time Machine Backup/Scott’s MacBook Pro.sparsebundle” is already in use."  What is wrong and how do I fix it?  Thanks.

    Have you tried restarting the computer? Also, see Time Machine Error from this pages sidebar under More Like This.

  • Synchronise time machine from HardDrive to macbook pro

    how do i synchronise time machine from HardDrive to macbook pro?

    Check this out by Pondini, the resident TM guru here, read thru, and you will most likely find your answer:
    http://pondini.org/OSX/Home.html

  • Use  back up from Time Machine to start new MacBook Pro

    Using the Time Machine and an external Hard Drive I  back up my 3 years old MacBook  (running Lion  and with hard drive of  250 GB)
    I am planning to purchase a new MacBook Pro (with a hard drive of 750 GB)
    how  do I transfer all my software  and Data to my new computer?
    if  I plug my  Time Machine to it will set up my new computer just the way I have my old Computer?
    will all software work properly?
    Any thing else I should  have in Consideration??

    K2spuky wrote:
    Using the Time Machine and an external Hard Drive I  back up my 3 years old MacBook  (running Lion  and with hard drive of  250 GB). Will all software work properly?
    The old machine is running Lion already, then all your programs are ready already for the new machine with Lion.
    how  do I transfer all my software  and Data to my new computer?
    if  I plug my  Time Machine to it will set up my new computer just the way I have my old Computer?
    Plug the TimeMachine drive into the new computer, boot it and when you go through the setup there will be a opportunity to transfer from the TM drive.
    Shouldn't be a problem as your already on Lion.
    Of course if your older machine software is crappy and slow, so will your new machine.
    You might decide to fresh install instead, create the same user on the new machine then install all your programs from fresh original sources and then transfer files manually from the older machine, droppping the contents right into the same user folders as on the old machine.
    More work, but actually saves work if your older machine is screwed up. Because Setup and Migration assistant has no brains, it transfers crap just as well as the good stuff. and despite what it says, it seems to transfer programs even if you state you just want files. Why I don't know, it's what someone said.
    I never use either, because reinstalling the whole OS again, especially Lion with the Internet download, is not worth the chance. I'd rather download a few programs and transfer manually, takes about the same amount of time.

  • How can i transfer data from old MacBook Pro, which is too old to update time machine, to the newest MacBook Pro?

    I recently bought a new MacBook Pro, and wanted to transfer all the data from my old MacBook Pro, but I get the message saying I need to update time machine on my old one in order to use time machine. However, my old one is too old to update. So I decided to use the cable to transfer, because I heard I can do it that way even though it could take time. But I have no idea what to do...
    Can someone help me?

    A Basic Guide for Migrating to Intel-Macs
    The Knowledgebase article Intel-based Mac: Some migrated applications may need to be updated refers to methods of dealing with migrating from PowerPC chips to Intel with the Migration Assistant safely. The authors of this tip have not had a chance to verify this works in all instances, or that it avoids the 10.6.1 and earlier Guest Account bug that caused account information to get deleted upon use of the Migration/Setup Assistant. However, a well backed up source that includes at least two backups of all the data that are not connected to your machine will help you avoid potential issues, should they arise. In event it does not work, follow the steps below.
    If you are migrating a PowerPC system (G3, G4, or G5) to an Intel-Mac be careful what you migrate.  Keep in mind that some items that may get transferred will not work on Intel machines and may end up causing your computer's operating system to malfunction.
    Rosetta supports "software that runs on the PowerPC G3, G4, or G5 processor that are built for Mac OS X". This excludes the items that are not universal binaries or simply will not work in Rosetta:
    Classic Environment, and subsequently any Mac OS 9 or earlier applications
    Screensavers written for the PowerPC System Preference add-ons
    All Unsanity Haxies Browser and other plug-ins
    Contextual Menu Items
    Applications which specifically require the PowerPC G5 Kernel extensions
    Java applications with JNI (PowerPC) libraries
    See also What Can Be Translated by Rosetta.
    In addition to the above you could also have problems with migrated cache files and/or cache files containing code that is incompatible.
    If you migrate a user folder that contains any of these items, you may find that your Intel-Mac is malfunctioning. It would be wise to take care when migrating your systems from a PowerPC platform to an Intel-Mac platform to assure that you do not migrate these incompatible items.
    If you have problems with applications not working, then completely uninstall said application and reinstall it from scratch. Take great care with Java applications and Java-based Peer-to-Peer applications. Many Java apps will not work on Intel-Macs as they are currently compiled. As of this time Limewire, Cabos, and Acquisition are available as universal binaries. Do not install browser plug-ins such as Flash or Shockwave from downloaded installers unless they are universal binaries. The version of OS X installed on your Intel-Mac comes with special compatible versions of Flash and Shockwave plug-ins for use with your browser.
    The same problem will exist for any hardware drivers such as mouse software unless the drivers have been compiled as universal binaries. For third-party mice the current choices are USB Overdrive or SteerMouse. Contact the developer or manufacturer of your third-party mouse software to find out when a universal binary version will be available.
    Also be careful with some backup utilities and third-party disk repair utilities. Disk Warrior, TechTool Pro , SuperDuper , and Drive Genius  work properly on Intel-Macs with Leopard.  The same caution may apply to the many "maintenance" utilities that have not yet been converted to universal binaries.  Leopard Cache Cleaner, Onyx, TinkerTool System, and Cocktail are now compatible with Leopard.
    Before migrating or installing software on your Intel-Mac check MacFixit's Rosetta Compatibility Index.
    Additional links that will be helpful to new Intel-Mac users:
    Intel In Macs
    Apple Guide to Universal Applications
    MacInTouch List of Compatible Universal Binaries
    MacInTouch List of Rosetta Compatible Applications
    MacUpdate List of Intel-Compatible Software
    Transferring data with Setup Assistant - Migration Assistant FAQ
    OS X Lion: How to use Migration Assistant to transfer files from another Mac
    Because Migration Assistant isn't the ideal way to migrate from PowerPC to Intel Macs, using Target Disk Mode, copying the critical contents to CD and DVD, an external hard drive, or networking will work better when moving from PowerPC to Intel Macs.  The initial section below discusses Target Disk Mode.  It is then followed by a section which discusses networking with Macs that lack Firewire.
    If both computers support the use of Firewire then you can use the following instructions:
    Repair the hard drive and permissions using Disk Utility.
    Backup your data.  This is vitally important in case you make a mistake or there's some other problem.
    Connect a Firewire cable between your old Mac and your new Intel Mac.
    Startup your old Mac in Transferring files between two computers using FireWire.
    Startup your new Mac for the first time, go through the setup and registration screens, but do NOT migrate data over. Get to your desktop on the new Mac without migrating any new data over.
    If you are not able to use a Firewire connection (for example you have a Late 2008 MacBook that only supports USB:)
    1. Set up a local home network: Creating a small Ethernet Network.
    2. If you have a MacBook Air or Late 2008 MacBook see the following:
    MacBook (13-inch, Aluminum, Late 2008) and MacBook Pro (15-inch, Late 2008)- What to do if migration is unsuccessful;
    MacBook Air- Migration Tips and Tricks;
    MacBook Air- Remote Disc, Migration, or Remote Install Mac OS X and wireless 802.11n networks.
    Copy the following items from your old Mac to the new Mac:
    In your /Home/ folder: Documents, Movies, Music, Pictures, and Sites folders.
    In your /Home/Library/ folder:
    /Home/Library/Application Support/AddressBook (copy the whole folder) /Home/Library/Application Support/iCal (copy the whole folder)
    Also in /Home/Library/Application Support (copy whatever else you need including folders for any third-party applications)
    /Home/Library/Keychains (copy the whole folder) /Home/Library/Mail (copy the whole folder) /Home/Library/Preferences/ (copy the whole folder) /Home /Library/Calendars (copy the whole folder) /Home /Library/iTunes (copy the whole folder) /Home /Library/Safari (copy the whole folder)
    If you want cookies:
    /Home/Library/Cookies/Cookies.plist /Home/Library/Application Support/WebFoundation/HTTPCookies.plist
    For Entourage users:
    Entourage is in /Home/Documents/Microsoft User Data Also in /Home/Library/Preferences/Microsoft.
    Credit goes to Macjack for this information.
    If you need to transfer data for other applications please ask the vendor or ask in the  Discussions where specific applications store their data.
    5. Once you have transferred what you need restart the new Mac and test to make sure the contents are there for each of the applications.
    Written by Kappy with additional contributions from a brody.Revised 5/21/2011

  • How do I restore from time machine on a new macbook pro ?

    Hello,
    My Macbook pro was stollen about 2 months ago and i'm currently debating on which Macbook retina I should get, the higher 13" or the higher 15" model. In either case, how do I go about restoring the system to which my old macbook pro was at ? i.e getting the same itunes songs files, iPhoto pictures etc.
    I have read that if the version of the os x in the time machine was an earlier than that on the new machine it would cause problems. so how do can I work around that if i face this problem ?
    One last question, how can I know the space needed on the new system for the restoration from the time machine?

    The new machine will boot into Setup Assistant, and you'll be prompted to import the data from a Time Machine backup, among other options. A system-version mismatch is OK.

  • External Hard Drive and Time Machine no longer recognized

    I recently downloaded the latest software update and upon rebooting the system to install the security update and whatever other update was included, my external hard drive which contains time machine is no longer recognized. I tried to use disk utility to mount it, fix it, but nothing worked. I am led to think that it's gotta be something in the latest update because i haven't had any problems before this. Sometimes the drive shows up as a yellow image sometimes in disk utility, the rest of the time it is a sort of transparent gray. What's wrong with my machine??? Can i simply uninstall the latest update? would that even solve this issue? i NEED to get into this drive and recover these files

    BUMP! Count me in on this one. The last Time Machine back-up was 12/6. I take my machine to the office during the week but am working from home this week. My other external drive (Archives) shows up, but Time Machine is MIA. Looking at System Profiler under USB, I can see the drive on the USB hub and the volume is labeled Time Machine, so the computer sees it, it just doesn't mount it to the desktop so Time Machine can't find its drive.
    I've turned the drive off and on. I've swapped cables with the Archive drive. I've rebooted. Nothing works. Both are Western Digital MyBook Studio editions. Both are plugged in to the same hub. I also switched the cables on the hub, but if it's showing up in the Profiler, the problem isn't with the hub, the drive or the cable.
    Suggestions? Clues? Comments? I'd rather not lose a year's worth of Time Machine back-ups at this point, plus I can't even reformat the drive.

  • Issues with restoring a Time Machine backup onto new Macbook Pro Retina

    I recently got a new Macbook Pro Retina and I've been trying to restore a Time Machine backup made today from my old Macbook Pro laptop. I didn't restore from the first start up (foolishly, seemingly) simply because of the trivial reason of wanting to see the system all clean and new.
    I've tried the Migration Assistant but it gets stuck on "looking for source..", despite having the ex.HD plugged in and double checking the existance of the backup itself on the ex.HD.
    I've also tried booting the laptop up in the 'restore' mode (cmd R) and restoring from there but it sends me in a constant loop of 'this backup was from a previous model of laptop' or something to that affect. It also doesn't display the recent backups at all, only displaying those from the beginning of this year for some reason. All backups are in the same place on the ex.HD so its not an issue with locating the backups.
    Really stuck on this one! Would really appreciate some help!
    Thanks a lot, and merry Christmas

    Yes, you can restore to another machine if needs be.

  • Cannot access Time Machine backups on new MacBook Pro

    Hey, I'm new to the forums, just wanting to throw it out there.
    But to the point- Yesterday, I purchased a new MacBook Pro. I upgraded from a regular MacBook. I want to keep my Music, Pictures, and other Documents, so I used Time Machine to make an image of the old machine. I want to copy those specific folders over individually, so I didn't use the option to restore from the Time Machine backup. When I copied my Music folder into the location I wanted it, I tried to open the folder, and received an error message saying:
    "The folder "Music" could not be opened because you do not have sufficient access privileges."
    I went through Get Info and changed Permissions to Read and Write for Everyone. I don't really know what to do from here... It also does this when I try to access the backups on my external hard drive. Please help me!

    Hi, and welcome to the forums.
    You need to Restore the files from the backups, not copy them via the Finder. Time Machine, as you now know, uses special "deny everybody everything" permissions on it's backups to keep us mere mortals from moving, changing, or deleting them, which can hopelessly corrupt them. Restoring one Mac's backups to another one takes a few extra steps.
    TM keeps the backups for each Mac separate, and normally only shows the ones for the Mac it's running on, even if there are other Macs' backups on the same disk/partition.
    Since you're on a different Mac, you need the (badly named) +Browse Other Time Machine Disks+ option to see the old backups. Start with a normal Finder window, then hold down the Option key while selecting the TM icon in your Menubar, or by control-clicking (right-clicking) the TM icon in your Dock.
    You'll see a selection screen showing all the disks/partitions that have TM backups on them. Select the one you want, and you'll be taken to the normal TM "Star Wars" interface, where you should see all the backups on that disk/partition.
    You can then navigate to a backup (presumably the most recent one), in the "cascade" in the center of the display (the first, lowest one, represents "now"). Navigate to the folder you want to restore, select it, click the "gear" icon in the Finder window's toolbar and select the +Restore to ...+ option. Then you'll get a prompt for the destination.

  • Using MacBook Time Machine in a new MacBook Pro-possible?

    Hi All,
    Apologize if this is a re-post question or very basic. But appreciate your help.
    I have been using a MacBook (white) for sometimes and take advantage of the Time Machine in its MacOS X to back up my files. I am planning to get myself a new MacBook Pro. However, I wonder whether I could use all the time machine backup in my external harddrive of my MacBook with the new MacBook Pro.
    Is anyone can give me suggestion? How to do this if this is possible.
    Thanks

    you can use Migration Assistant (it's in /Applications/Utilities) to migrate your user data and applications from the MB backup to the new MBP. You'll also have the same option during the initial computer setup. after that MBP will need to start its own backup sequence. It can't use the old MB backups except in browse mode.

  • "Reconnecting" Time Machine Backups on New Macbook Pro

    I recently got a new macbook pro and used Time Machine to set it up. Unfortunately, when I attempt to continue to use time machine backups, I get the warning that I don't have enough space.
    I next attempted to use the Pondini B6 troubleshoot to reconnect my backups via the terminal (http://pondini.org/TM/B6.html), however upon attempting to execute the "sudo tmutil inheritbackup" command I received the following error message:
    The backup "I***Mac" can't be inherited because it would conflict with "I***’s MacBook Pro" (with I***Mac being the name of my old laptop and I***'s MacBook Pro being my new one).
    Does anyone have any suggestions? Should I just wipe my backup HD?
    Thanks so much

    It helps!
    After this:
    sudo tmutil delete "/Volumes/Time Machine/Backups.backupdb/Computername 2/"
    sudo tmutil associatedisk -a /Volumes/Mac\ HD /Volumes/Time\ Machine/Backups.backupdb/Computername/Latest/Mac\ HD
    I was able to go into Time Machine and see the backups that were in Computername that I hadn't been able to see via Time Machine (but could see from the command line).
    And then I deleted a folder in TIme Machine (a profile inside ~/Library/Application Support/Firefox and the entire old backup in /Volumes/Time\ Machine/Backups.backupdb/Computername/ was deleted.  Perhaps fat fingers?  I dunno.  I have a volume copy of the Time Machine volume, so I'll try again...

  • Restore from Time machine on new 13" Macbook Pro 2.8 i7 after replacing with OWC SSD

    I have new 13" Macbook pro with Apple 256SSD. I am replacing with OWC 480GB 6GB SSD because out of space. When I bought machine I used time machine to restore from backup of other macbook pro. I simply held a key on keyboard at startup (dont remember key?) and it appeard to boot from the cloud to a screen where i selected time machine. Will it work the same this time or because I am replacing hard drive i have to create the USB  key thing to restore from time machine? ie does apple have the restore from cloud capability only from their own drives?

    You should consider restoring or migrating first only data that you absolutely need and want on the SSD. Then restore selectively.
    On the latter, and in general on the topic Time Machine, here is good advice.

Maybe you are looking for