Time Machine to AFP volume is extremely slow after 10.5.2 update
I remember the time, after I have just installed the very first version of Leopard, when Time Machine was working with close to physical speed of my wireless network. Incremental backups would take less than a minute.
Comes 10.5.1. Time Machine became slower, but still tolerable: it might take up to 10 minutes to do an hourly backup.
Comes 10.5.2. Now Time Machine might take a couple of hours to do its "hourly" backup! 99% of the time it spends backing stuff up - when it shows the progress of the backup. So right now it says it's backing up 34.1 megabytes, and then it stopped at 1.4 megabytes, spent there about 15 minutes. Then it continued to about 9.5 megabytes, spend another 20 minutes there, without any progress, no CPU usage, very little network usage. Then it progressed to about 10.5 megabytes, and stuck again. Now it's at 15.2 megabytes, and been there for about 10 minutes already.
I use Airport Extreme base station with 802.11n at 5GHz, and the backup volume is on my Mac Mini, connected to AEBS via an ethernet cable, and during the phases when Time Machine gets stuck, I tested how the network works from my MacBook Pro, which I'm trying to backup to Mac Mini - constantly getting about 8-9 megabytes per second transfer rate, so clearly it's not that my wireless network is experiencing issues. Besides, the same problem persists even if I plug Ethernet cable directly into my MacBook Pro.
I've cleaned all caches, repaired permissions, repaired all volumes, rebuilt Spotlight indices on both my MacBook Pro and in the backup sparse bundle. The only thing it solved is insanely long "Preparing for backup" issue, but it DIDN'T solve the slow backup I have just described.
For comparison: rsync takes about a minute to do a full sync of my entire hard drive to the same AFP volume. Apple Backup 3.1.2 takes about as much. Time Machine - hours. I fail to even begin to imagine what in a world might they be doing there, spending this much time copying 34.1 megabytes of data over the network.
P.S. As I finish writing this, the backup progress is still at 15.2 magebytes. About 15 minutes now. A little over an hour now and not even half of the 34 megabytes is completed.
Message was edited by: Farlander
Message was edited by: Farlander
Is it slow wireless LAN behavior affecting Time Machine? Check out the third page of this thread, specificallly the post by John Albergo about "delay_ack."
http://discussions.apple.com/thread.jspa?threadID=1394485&start=30&tstart=0
It helped me a lot.
Similar Messages
-
My mbp (mid 2010) is running extremely slow after installing some mavericks updates on May 22nd.
My mbp (mid 2010) is running extremely slow after installing some mavericks updates on May 22nd. Earlier I thought this behavior is due to spotlight indexing but it finished after 3 days. I deleted all caches from library. But no luck, still running extremely slow. I checked activity monitor for cpu usage, it shows above 90% is idle. The memory usage always shows PM - 4 GB, Memory Used 3.96 GB, VM - 4 GB, Swaped used 0 bytes, App Memory 1.82 GB, File Cache 1.44 GB, Wired Memory 480 MB.
Thanks in adavnce for help.Was it the combo updater that was installed or the OS X 10.9.3 update. There is a difference.
MORE INFO ON WHY RUNNING COMBO FIXES ISSUES
Apple updates available from the Software Update application are incremental updates. Delta updates are also incremental updates and are available from Apple Downloads (software updates are generally smaller than delta updates). The Combo updates contain all incremental updates and will update files that could have become corrupted.
Combo updaters will install on the same version as they're applying--no need to roll back or do a clean install. So if you think you've got a borked 10.8.4 install from a regular update, just run the 10.8.4 Combo Updater on that system.
"Delta" updaters can only take you from one version to the next. For example: 10.9.1 to 10.9.2. If somehow the 10.9.2 is missing something it should have, and that something isn't changed between 10.9.1 and 10.9.2 it will still be stale after the delta update. -
Disk access extremely slow after 10.5.2 Update
I did the update to 10.5.2 today.
1. I tried to update via Software Update. The update started but then stopped with an Error message (Contact Support) and the system freezed. There was just the spinning wheel on blue background for more than one hour. No more harddisk activity. I finally rebooted (hard way). After a reboot I had a somehow upgraded system. But many things did not work anymore (most applications crashed, mail could not access keychain items anymore, etcpp)
2. Then I downloaded the complete Update package to do a manual update (happily firefox still worked). After a manual install it worked. It installed fine and rebooted. Now everything works as it should with the only problem that everything is extremly slow. Starting an application lasts about double the time as normal, loading files takes 3 to 4 times more time than with 10.5.1
To fix these issues I tried several things:
- Fixed permissions
- Cleared all cache files and forced system to rebuild them
- Severall reboots
- Waited until backup completed and Spotlight index was rebuilt
Bootup time is now fine (more or less). Just a little slower than 10.5.1. Application start is still slow but better. But the file access is still extremly slow. This can be observed very well in Parallels which still works fine, but needs 3 to 4 times longer to start (so do all applications within parallels). I checked CPU (Activity Monitor) but could not see anything special.
Any ideas what could be the reason for this behaviour and (more important) how to possibly fix this? I'm thinking about going back to 10.5.1 with time-machine and then try it again with the package install.
Any help/ideas would be appreciated.Is it slow wireless LAN behavior affecting Time Machine? Check out the third page of this thread, specificallly the post by John Albergo about "delay_ack."
http://discussions.apple.com/thread.jspa?threadID=1394485&start=30&tstart=0
It helped me a lot. -
Hi folks. Since my last software update, my computer has slowed to a near halt. Help!
I have a late 2009 MacBook Pro, running OS X 10.8.2. 2.26 Ghz / 8 gb memory.
I went into the Disk Utility and ran "verify disk," and got an "ok." Verified and repaired disk permissions. No idea if they're relevant.
At this moment the activity monitor is showing 3.79 gb of free memory -- 10 minutes ago, when I was doing nothing particularly differently, it showed all 7.99 gb in use (active and inactive -- I have. No idea what this means.)
It's all beach balls around here, all the time. Any ideas?Your problem is excessive swapping of data between physical memory and virtual memory.
That can happen for two reasons:
You have a long-running process with a memory leak (i.e., a bug), or
You don't have enough memory installed for your usage pattern.
Tracking down a memory leak can be difficult, and it may come down to a process of elimination. In Activity Monitor, select All Processes from the menu in the toolbar, if not already selected. Click the heading of the Real Mem column in the process table twice to sort the table with the highest value at the top. If you don't see that column, select
View ▹ Columns ▹ Real Memory
from the menu bar.
If one process (excluding "kernel_task") is using much more memory than all the others, that could be an indication of a leak. A better indication would be a process that continually grabs more and more memory over time without ever releasing it.
If you don't have an obvious memory leak, your options are to install more memory (if possible) or to run fewer programs simultaneously.
The next suggestion is only for users familiar with the shell. For a more precise, but potentially misleading, test, run the following command:
sudo leaks -nocontext -nostacks process | grep total
where process is the name of a process you suspect of leaking memory. Almost every process will leak some memory; the question is how much, and especially how much the leak increases with time. I can’t be more specific. See the leaks(1) man page and the Apple developer documentation for details:
Memory Usage Performance Guidelines: About the Virtual Memory System -
Iphone 4s is extremely slow after 5.1.1 update
Since updating to the latest (5.1.1) my phone is barely usable for anything mroe than 'just' a phone and basic texting.
Web browsing is terribly slow - regardless of if using data network or wireless connection at home. Apps are slow to respond and often the touch screen doesn't even register being touched or registers the touch incorrectly (wrong position for ex.)I am aware what reverting to default means - unless you're a developer yourself, probably more aware than you are.
The problem is the update, not apps installed (and fyi yes I have reverted to default - as have many others that I've seen posting even here, and having issues still) but rather the update. This isn't a request for assistance. This is a report of an issue - and of a disgruntled user
back-to back-to back updates released and causing people issues and then innane attempts at 'fixing' the issue by telling people to jump through hoops until they get sick of trying and then just deal with the issues in hopes of an update that actually works (ie: resolves issues without causing more and worse issues) leads to customers taking business elsewhere.
which is what I'll be doing. My wife will be getting a new phone in july and as of right now it certainly wont be an apple product. -
nas on airport extreme not recognized by time machine. same nas was previously used as time machine backup on different airport extreme. are there any configuration files that i can delete to fix this problem ?
Time Machine has been working just fine, but in the last week or two it has given up the ghost. I reset the connections to the drive, and it will basically save a few bytes of data and then hang.
Although Apple originally announced, prior to the release of the first 802.11n AirPort Extreme Base Stations (AEBSn), that it would support Time Machine backups to AirPort Disks, they removed that option before they did finally release the base station for sale.
Since then, Apple has posted (as you have noted) that they DO NOT support Time Machine backups to AirPort Disks. As far as I know, they have not changed from that position and those who do these backups find that they become corrupted over time. Sorry, but it sounds like you just confirmed that for yourself.
1) Has one of the recent updates either on the AE (firmware) or OSX disabled this function?
No. Again, this feature has never been supported by Apple for every generation of AEBSn released.
2) Are there any changes I can make to get this working again?
If your data backups are critical to you, then you will want to use a different solution for your Time Machine backup destination drive strategy. I would suggest that you connect your WD My Book directly to your Mac in the mean time.
Your other options would be to either use a Time Capsule (which interestingly does support TM backups to AirPort Disks) or a non-Apple solution like the Drobo FS or HP MediaSmart server. -
my final cut is running extremely slow after having for 6 months. I use external hard drives and save nothing on my computer. it takes a long time to render now. do you think something is wrong with computer. took it to mac store but they fail to help me. I have a 13 inch mac book pro 10.6.8 8gb 2.3 gfz intel core i5
What did Apple tell you about what they did (or did not) find here?
See if working on the main disk is any faster.
USB2 is glacial, as I/O interconnects go. And USB2 disks have been known to fail, or sometimes to drop back to USB1 speeds, too. FireWire 800 is substantially faster than USB2, but still not as fast as the internal drive connections can provide.
Put another way, start varying your configuration, and see which configuration changes (still) have the problem, and which don't. -
I have not been able to back up for2 days. Time machine error message: /Volumes/Data/David’s MacBook Air.sparsebundle” is already in use.
What now?
Macbook Air.
Was working fine for the past year until now.See more like this on the right.. this is the most common error reported here since mountain lion came out..
Or read C12.. http://pondini.org/TM/Troubleshooting.html
Or just restart the whole network.. in right order from off.. modem.. router / TC.. clients 2min gap. -
How to prevent Time Machine from ejecting volume?
I just set up a Buffalo Cloustor NAS (which is working very nicely, thank you) and one of its features is that it plays nice with Time Machine backups. I also recently took advantage of a MacUpdate promo on Back-In-Time. BIT works fine as long as the NAS backup volume is mounted but for some reason Time Machine ejects that volume when it's finished its backups. I've seen similar problems in threads of non-Lion version of OSX but they seemed to be troubles with USB or FW drives rather than an Ethernet NAS. I'd rather keep the NAS volume mounted so I can use this 3rd party app.
Here is a copy of the console messages filtered on "time machine" for the relevant time period:
3/24/12 7:11:03.180 PM
com.apple.backupd
Disk image /Volumes/cloudshare/Mini2009’s Mac mini.sparsebundle mounted at: /Volumes/Time Machine Backups
3/24/12 7:11:03.196 PM
com.apple.backupd
Backing up to: /Volumes/Time Machine Backups/Backups.backupdb
3/24/12 7:12:37.276 PM
com.apple.backupd
Ejected Time Machine disk image.
3/24/12 7:12:37.678 PM
com.apple.backupd
Ejected Time Machine network volume.
Is there a way of telling Time Machine to not eject when finished? I'm comfortable writing stuff using Terminal if that's what it takes.
Thanks!
-TodBordeauxQuill wrote:
If it is useful to anyone else, these are Western Digital My Passport Studio 640GB drives.
Yup, you're the 3rd or 4th to report it with various models of WDs (one fellow had 3 of them!), and a few weeks ago someone had some Iomegas, I think, too.
This confusion may well also explain some weird stats in Get Info I noticed last week (such as the drive apparently having used more bytes than its capacity, as I recall).
Quite likely.
Thank you for your support. I shall come back and mark the thread resolved when I have reformatted the drive.
Cool. Also double-check the contents of the one you don't erase; you may find some extra stuff there. -
Time Machine not backing up. Very slow, essentially hanging. I have 10.7.5 Mac OS X Lion (11G63). I have put in all updates. I tried to put my folders into "private" in the Spotlight (b/c I read that might be the problem). Still not working.
Thanks in advance for any help!For all things Time Machine see Pondini's excellent information here...
http://pondini.org/OSX/Home.html
Start at Troubleshooting. -
Time machine cannot find volume, error-1. Where can I fine solution for this error? Have latest updates for Airport Utility and TM, running Lion.
See #C17 in Time Machine - Troubleshooting.
-
Problem description:
My Mac Pro is extremely slow after upgrading to Yosemite 10.10, even while reading my newspaper on PDF
This is my EtreCheck print
EtreCheck version: 2.0.11 (98)
Report generated 17. november 2014 kl. 10.49.28 CET
Hardware Information: ℹ️
MacBook Pro (13-inch, Mid 2012) (Verified)
MacBook Pro - model: MacBookPro9,2
1 2.5 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1600 MHz ok
BANK 1/DIMM0
2 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en1: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 4000 -
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10 (14A389) - Uptime: one day 15:45:13
Disk Information: ℹ️
TOSHIBA MK5065GSXF disk0 : (500,11 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / [Startup]: 498.88 GB (290.89 GB free)
Encrypted AES-XTS UnlockedConverting
Core Storage: disk0s2 499.25 GB Online
MATSHITADVD-R UJ-8A8
USB Information: ℹ️
Apple Inc. FaceTime HD Camera (Built-in)
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Library/Extensions
[loaded] net.telestream.driver.TelestreamAudio (1.1.1 - SDK 10.8) Support
/System/Library/Extensions
[not loaded] com.devguru.driver.SamsungComposite (1.4.20 - SDK 10.6) Support
/System/Library/Extensions/ssuddrv.kext/Contents/PlugIns
[not loaded] com.devguru.driver.SamsungACMControl (1.4.20 - SDK 10.6) Support
[not loaded] com.devguru.driver.SamsungACMData (1.4.20 - SDK 10.6) Support
[not loaded] com.devguru.driver.SamsungMTP (1.4.20 - SDK 10.5) Support
[not loaded] com.devguru.driver.SamsungSerial (1.4.20 - SDK 10.6) Support
Launch Agents: ℹ️
[loaded] com.divx.dms.agent.plist Support
[loaded] com.divx.update.agent.plist Support
[loaded] com.oracle.java.Java-Updater.plist Support
Launch Daemons: ℹ️
[failed] com.adobe.fpsaud.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
[loaded] com.oracle.java.Helper-Tool.plist Support
[loaded] com.oracle.java.JavaUpdateHelper.plist Support
[invalid?] com.torch.update.agent.plist Support
User Launch Agents: ℹ️
[loaded] com.genieo.completer.download.plist Support
[loaded] com.genieo.completer.ltvbit.plist Support
[loaded] com.genieo.completer.update.plist Support
[loaded] com.google.keystone.agent.plist Support
User Login Items: ℹ️
None
Internet Plug-ins: ℹ️
FlashPlayer-10.6: Version: 15.0.0.223 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
DivX Web Player: Version: 3.2.3.1164 - SDK 10.6 Support
Flash Player: Version: 15.0.0.223 - SDK 10.6 Support
OVSHelper: Version: 1.1 Support
Default Browser: Version: 600 - SDK 10.10
SharePointBrowserPlugin: Version: 14.4.4 - SDK 10.6 Support
Unity Web Player: Version: UnityPlayer version 4.5.5f1 - SDK 10.6 Support
Silverlight: Version: 5.1.20913.0 - SDK 10.6 Support
JavaAppletPlugin: Version: Java 8 Update 25 Check version
User Internet Plug-ins: ℹ️
NPRoblox: Version: 1, 2, 8, 25 - SDK 10.10 Support
Google Earth Web Plug-in: Version: 7.1 Support
Safari Extensions: ℹ️
Omnibar
3rd Party Preference Panes: ℹ️
Flash Player Support
Java Support
Perian Support
Time Machine: ℹ️
Skip System Files: NO
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 498.88 GB Disk used: 207.99 GB
Destinations:
Elements [Local]
Total size: 1.00 TB
Total number of backups: 0
Oldest backup: -
Last backup: -
Size of backup disk: Adequate
Backup size 1.00 TB > (Disk used 207.99 GB X 3)
Top Processes by CPU: ℹ️
89% lsregister
3% WindowServer
1% mds
1% sysmond
0% mtmd
Top Processes by Memory: ℹ️
142 MB Preview
125 MB com.apple.WebKit.WebContent
125 MB Finder
86 MB ocspd
77 MB com.apple.WebKit.Plugin.64
Virtual Memory Information: ℹ️
335 MB Free RAM
1.63 GB Active RAM
1.32 GB Inactive RAM
776 MB Wired RAM
17.27 GB Page-ins
345 MB Page-outsCheck out this thread: https://discussions.apple.com/thread/6466590?start=0&tstart=0.
For many users, the Folder Action Dispatcher is the culprit that eats almost all available memory if it is enabled on ~/Library/LaunchAgents. -
Problem description:
Load times for programs and websites is significantly slowed after Yosemite install.
EtreCheck version: 2.0.11 (98)
Report generated November 18, 2014 at 12:47:02 PM CST
Hardware Information: ℹ️
MacBook Pro (Retina, 13-inch, Early 2013) (Verified)
MacBook Pro - model: MacBookPro10,2
1 2.6 GHz Intel Core i5 CPU: 2-core
8 GB RAM Not upgradeable
BANK 0/DIMM0
4 GB DDR3 1600 MHz ok
BANK 1/DIMM0
4 GB DDR3 1600 MHz ok
Bluetooth: Good - Handoff/Airdrop2 supported
Wireless: en0: 802.11 a/b/g/n
Video Information: ℹ️
Intel HD Graphics 4000 -
Color LCD spdisplays_2880x1800Retina
System Software: ℹ️
OS X 10.10 (14A389) - Uptime: 6 days 2:35:1
Disk Information: ℹ️
APPLE SSD SM256E disk0 : (251 GB)
S.M.A.R.T. Status: Verified
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / [Startup]: 249.77 GB (185.10 GB free)
Core Storage: disk0s2 250.14 GB Online
USB Information: ℹ️
HP HP Officejet Pro 8610
Apple Inc. BRCM20702 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. FaceTime HD Camera (Built-in)
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/Library/Extensions
[not loaded] com.intego.Family-Protector.safe-boot (2271 - SDK 10.8) Support
/System/Library/Extensions
[loaded] com.globaldelight.driver.BoomDevice (1.1 - SDK 10.9) Support
Launch Agents: ℹ️
[not loaded] com.adobe.AAM.Updater-1.0.plist Support
[running] com.intego.commonservices.integomenu.plist Support
[running] com.intego.commonservices.taskmanager.plist Support
[loaded] com.intego.commonservices.uninstaller.plist Support
[running] com.intego.Family-Protector.agent.plist Support
[running] com.intego.netbarrier.alert.plist Support
[running] com.intego.netupdate.agent.plist Support
[loaded] com.intego.personalbackup.agent.plist Support
[loaded] com.intego.virusbarrier.alert.plist Support
Launch Daemons: ℹ️
[loaded] com.adobe.fpsaud.plist Support
[running] com.intego.commonservices.daemon.integod.plist Support
[running] com.intego.commonservices.daemon.taskmanager.plist Support
[loaded] com.intego.commonservices.icalserver.plist Support
[loaded] com.intego.commonservices.metrics.kschecker.plist Support
[running] com.intego.Family-Protector.daemon.plist Support
[running] com.intego.netbarrier.daemon.logger.plist Support
[running] com.intego.netbarrier.daemon.monitor.plist Support
[running] com.intego.netbarrier.daemon.plist Support
[running] com.intego.netupdate.daemon.plist Support
[running] com.intego.PersonalBackup.daemon.plist Support
[loaded] com.intego.virusbarrier.daemon.emlparser.plist Support
[running] com.intego.virusbarrier.daemon.logger.plist Support
[running] com.intego.virusbarrier.daemon.plist Support
[running] com.intego.virusbarrier.daemon.scanner.plist Support
[running] com.intego.WashingMachine.service.plist Support
[loaded] com.microsoft.office.licensing.helper.plist Support
User Launch Agents: ℹ️
[loaded] com.adobe.AAM.Updater-1.0.plist Support
[loaded] com.google.keystone.agent.plist Support
User Login Items: ℹ️
Boom Application (/Applications/Boom.app)
iTunesHelper Application (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
Dropbox Application (/Applications/Dropbox.app)
ElementsAutoAnalyzer Application (/Applications/Adobe Elements 12 Organizer.app/Contents/ElementsAutoAnalyzer.app)
Internet Plug-ins: ℹ️
Flip4Mac WMV Plugin: Version: 3.2.0.16 - SDK 10.8 Support
FlashPlayer-10.6: Version: 15.0.0.223 - SDK 10.6 Support
QuickTime Plugin: Version: 7.7.3
Flash Player: Version: 15.0.0.223 - SDK 10.6 Support
CouponPrinter-FireFox_v2: Version: 1.1.10 - SDK 10.6 Support
Default Browser: Version: 600 - SDK 10.10
WidevineMediaOptimizer: Version: 6.0.0.12757 - SDK 10.7 Support
SharePointBrowserPlugin: Version: 14.4.6 - SDK 10.6 Support
Silverlight: Version: 5.1.20913.0 - SDK 10.6 Support
Safari Extensions: ℹ️
Adblock Plus
3rd Party Preference Panes: ℹ️
Flash Player Support
Flip4Mac WMV Support
Time Machine: ℹ️
Auto backup: YES
Volumes being backed up:
Macintosh HD: Disk size: 249.77 GB Disk used: 64.67 GB
Destinations:
My Passport [Local]
Total size: 249.38 GB
Total number of backups: 3
Oldest backup: 2014-01-06 19:50:48 +0000
Last backup: 2014-01-09 23:24:23 +0000
Size of backup disk: Adequate
Backup size 249.38 GB > (Disk used 64.67 GB X 3)
Top Processes by CPU: ℹ️
4% WindowServer
1% coreaudiod
0% fontd
0% Boom
0% netbiosd
Top Processes by Memory: ℹ️
627 MB WindowServer
472 MB virusbarriers
223 MB Mail
129 MB com.apple.WebKit.WebContent
129 MB Safari
Virtual Memory Information: ℹ️
414 MB Free RAM
4.25 GB Active RAM
1.06 GB Inactive RAM
1.29 GB Wired RAM
12.00 GB Page-ins
602 MB Page-outs1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.AAM.Updater-1.0 com.adobe.AAM.Updater-1.0 com.adobe.AdobeCreativeCloud com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.adobe.SwitchBoard com.apple.aelwriter com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.rpmuxd com.apple.SafariNotificationAgent com.apple.usbmuxd com.citrixonline.GoToMeeting.G2MUpdate com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper com.oracle.java.JavaUpdateHelper org.macosforge.xquartz.privileged_startx org.macosforge.xquartz.startx ' ' 879294308 4071182229 461455494 3627668074 1083382502 1274181950 1855907737 2758863019 1848501757 464843899 3694147963 1233118628 2456546649 2806998573 2778718105 2636415542 842973933 2051385900 3301885676 891055588 998894468 695903914 1443423563 4136085286 523110921 3873345487 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^\([0-9]+\) /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: (E[^m]|[^EO])|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' { sub(/ :/,"");print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\\([0-9]+\\)\\(.+\\)/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/\(L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9|"sort|uniq";} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;' ' s/^.+ |\(.+\)$//g;p ' '/\.(appex|pluginkit)\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' ' /EVHF|MACR/d;s/^.+: //p;' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps crontab iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl smcDiagnose sysctl\ -n defaults\ read stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' pluginkit scutil dtrace profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil lsof test osascript\ -e );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. \( -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 \)' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender Req 'fsev|kern|launchd' -k RefProc Rne 'Aq|WebK' -k Message Rne 'Goog|ksadm|probe|Roame|SMC:|sserti|suhel| VALI|ver-r|xpma' -o -k Message Req 'abn|bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|NVDA\(|pagin|proc: t|Roamed|rror|SL|Throttli|tim(ed? ?|ing )o|WARN' " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true \) -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level '3>&1 >&- 2>&3' " -F '\$Time \$Message' -k Sender kernel -k Message CSeq 'n Cause: -' " );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors App\ extensions Lockfiles Memory\ pressure SMC Shutdowns );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};A'$((7+i))'() { v=` eval sudo "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};';done;A9(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2 7 8;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;B1&&D73 19 53 67 55;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 54 12 56;D23 5 14 12 14;D22 6 36 13 15;D22 20 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D82 35 49 61 51;D82 11 17 17 20;for i in 0 1;do D82 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A8 18 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 26 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D73 21 0 32 19;D73 10 42 32 40;D82 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 21 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D83 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 10 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 21 48 49 49;B3 4 22 57;A1 21 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A9;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed. -
Itunes starts extremely slow after an update of windows 8.1.
Itunes starts extremely slow after an update of windows 8.1.
It takes up to 10 minutus.
If I see the appliction log in event viewer then I see the following errors on the Bonjour service.
For instance:
Client application bug: DNSServiceResolve(a8:fa:d8:3a:1e:8f@fe80::aafa:d8ff:fe3a:1e8f._apple-mobdev2._t cp.local.) active for over two minutes. This places considerable burden on the network.
followed by
SendWakeupPacket error: sent -1 bytes: 10065
What can this be?
Already thanks,
JohnI did all the step with save mode and that didn't gave the same result.
Then I created a new account and there itunes started up normally.
So I contued with the user section.
I removed the itunes directory from
c:\Users\username\AppData\Local\Apple Computer\iTunes
This gave the same result in not starting up.
Then I removed the itunes directory from
c:\Users\username\AppData\Roaming\Apple Computer\iTunes
The a popup appears that the Bonjour Service has been disabled.
I looked in services and saw that is was still running.
But I tried to restart this service and it took a long time to stop this service.
Even if I selected restart the Bonjour Service didn't start.
Manually starting was not a problem.
Clicking OK on the popup let itunes start quickly. And closing and starting it again was also quickly.
So Matt thanks for your answer.
If it happens again I have to see if it was the removing of the itunes directory from roaming or restarting the Bonjour Service. -
Apple TV extremely slow after sleeping
Hi all, My apple tv early 2012 is extremely slow after its slept.. (by slow i mean the wifi connection, both to internet and airplay)... Its so slow you can't hear a song or anything, it keeps cutting in and out.. I don't know why this is and its starting to annoy me..
It has only been happening recently (last two weeks) so far I have tried :
multiple restars = works until the next time it goes into sleep mode or left for a long time
restore = same as above (latest software)
disconnect and reconnect does the same thing.. works until I leave it overnight..
Anyone with any ideas what this could be?
I thought maybe it was my router but none of my other products are doing this : iphone 4 and 5 and two laptops..
There has been no physical damage to the 6 months old apple TV
Thanks all!I have a macbook. but after the restore home share hasn't been activated.. its with streaming content from the internet with apple tv itself and also airplay runs extremely choppy
Maybe you are looking for
-
I've had itunes on my laptop for over a year; it seems to arbitrarily duplicate songs and now, instead of 800 songs, I have 3,500 with 2,700 being dupes. How do I get rid of the dupes?
-
Os x crashed. what could have been the issue??? [log attached]
here is the crash log... Interval Since Last Panic Report: 326223 sec Panics Since Last Report: 1 Anonymous UUID: B89DF022-5478-F968-7AFD-E80DF31E12C2 Wed Jan 30 09:56:51 2013 panic(cpu 0 caller 0xffffff80048b7bd5): Kerne
-
Hi, I am wondering if it is possible to lock a document on my computer. My siblings tend to delete and/or open files and mess around with them. They do have an extensive knowledge of Linux and their actions are more of malice. I am wondering if it wo
-
OK, so I think I have the basics of loading XML in AS3. But I can't seem to access the info once it is loaded. I'm using the to load the .xml file: var myXML:XML = new XML(); var XML_URL:String = "music.xml"; var myXMLURL:URLRequest = new URLRequest(
-
Is there any user exit in IW54 before document saving?
Dear experts, Is there any user exit in IW54 before document saving? I want to check some data before saving. thanks Lance