Time-out limit of the 8451-I2C interface for hold-master condition

I am working with Windows XP, Labview 8 and the USB-8451 I2C to USB interface-box.
We intend to incorporate the USB-8451 into our product evaluation kits for a new sensor product.
This evaluation kits should be used by our customers when they start working with our sensor products.
The I2C-device is a digital sensor which generates a hold-master condition with difference length, depending on the sensor configuration.
The hold-master is produced by the sensor after full transmassion of start-bit, address, read-bit and ACK.
After the hold master is suspended three bytes can be read by the master.
If the hold-master is kept by the sensor for 25 ms or less I have no problems. When keeping it significantly longer the interface seems not to work properly anymore. I don't get a LabView Error-Message but the PC (Windows?) creates a 'ding-dong' sound very similar to disconnecting and connection a USB device. (the 8451???). My LabView-Program does not show sensor data after this.
I can imagine that the hold-master is somehow too long for one element in the system.
Is there any time-out period for hold-master defined for the USB-8451?
How can I change it to higher values?
Thank you very much for your support!
Message Edited by UnexpectedLifeForm on 02-19-2007 09:48 AM

Dear Member,
That's right. If somebody encounter this problem again.
You should contact your local NI branch that will install the new firmware
version (that works with the last driver version)
Best regards,
Nick_CH

Similar Messages

I can't get my ipad3 to backup using iCloud.. It times out right at the end of backup

I can't get my ipad3 to backup using iCloud.. It times out right at the end of backup. The blue bar nearly fills up and right at the end a message pops up saying the backup could not be completed.

Tried that.. No joy. Just tried to synch again with iCloud . The bar gets nearly to the end and then stops. Says below it - estimated time remaining.... I'm confused. If I synch to my computer is this the same as synching to iCloud. It's shame it's doesn't work!

My Macbook will not boot the operating system. It just goes to a blue screen after the apple logo and the spinning wheel goes off. I took the battery out and held the on/off button for five seconds and reset the PRAM. I have the old mac os disk.

My macbook will not boot. It goes to a blue screen after the logo and wheel goes off. I have taken the battery out and held the on/off button for five seconds and reset the PRAM. I have the the original os disk but have not put it in for fear of losing un backed op data.
Thanks
Rich

You won't lose any data unless you erase your hard drive.
Put your install DVD into the optical drive and reboot. As soon as you hear the boot chime, hold down the "c"key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it.When it comes up is your Hard Drive in the list on the left?
If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've selected the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.

How to get the command line interface for WRT160NL router

hi,
How can I get the command line interface for WRT160NL router. please suggest.

If you’re trying to access the web-based interface of your router, just use its default IP address (192.168.1.1). The Username is left blank and the Password is "admin". Here’s a quick link on how to do that.

What's the best audio interface for Logic Pro and Mac?

What's the best audio interface for Logic Pro and Mac?

Depends on the computer model and if you have unlimited funds.

At what time on 19 sep, the ios6 is available for download?

At what time on 19 sep, the ios6 is available for download?

your welcome
ps I always download the whole package through iTunes
have had minor issues with update over the air inevitable requiring a restore

I am about to purchase an iPad. I have a Time Capsule. Are the two compatable? For example, when I bring the iPad home will it automatically link to my Time Capsule so everything I have on the capsule will be downloaded to the iPad?

I am about to purchase an iPad. I have a Time Capsule. Are the two compatable? For example, when I bring the iPad home will it automatically link to my Time Capsule so everything I have on the capsule will be downloaded to the iPad?

sherrycarlin wrote:
... will it automatically link to my Time Capsule so everything I have on the capsule will be downloaded to the iPad?
This is not how it works...
Suggest you spend a little bit of time here to be able to fully appreciate your iPad...
http://www.apple.com/support/ipad/essentials/
http://www.apple.com/support/ipad/apps/
From here > http://www.apple.com/support/ipad/
More info here > iPad User Guide iOS 6

Time out connection in the classes12.zip

Hello,
How can I change the time out connection to my database in Java ? I use the JDBC thin driver (classes12.zip) to connect to an 8.1.6 standard Oracle edition on an NT Server.
I tested a network problem connection removing the network cable and then my application waits 20 minutes to raise an exception.
Thanks
Guillaume Facon

You need to set a tcpip timeout at the os level. Oracle jdbc does not support timeouts.

Dump time out message in the portal

Hi experts ,
In my portal , the web dynpro component "FPM_OIF_COMPONENT" is being used.
when user logs in and then sit idle for 30 min. then after he press "save" button,
he gets the dump message like
"the URL http://...WebDynpro /sap/hap_main_document was not called due to an error
User session (HTTP/SMTP /..) closed after time out."
"the termination type was "ERROR_MESAGE_STATE"
but the Service "WebDynpro /sap/hap_main_document" remains active.
Timeout is set for 60 mins but it gets timeout after 30 mins.
I have to show a normal alert message instead of the dump mesage. how can i achieve that..
please help.

Hi Tobias ,
yes , !! time out for web dynpro is also set to 60 min .
But as per the requirment , i have to show a page / pop up msg displaying "portal time out " instead of that dump mesage.
in the meanwhile i have come across the t-code SICF , on executing it for services. then in the path
"sap -> bc -> webdynpro -> namspace SAP - > HAP_MAIN_DUCUMENT " i have found the setting to redirecting the user to a URL page when error occurs.for every type of error there is a option of "redirect to a URL".
I have not tested it.But i think it might work.i am still working on it.
your valuable feedback is welcome..
thanks
Nishchay

Does anyone have an answer yet to this time out thing with the Itunes 9????

I see so many threads but can't follow through each one. Does anyone have an answer to fix this?
dawniedoodle

What time out thing with iTunes 9? You'll get better answers if you give as much detail as possible when asking a question, including any error messages you've received and any trouble shooting steps you've already taken. From your question, it's not at all clear what your problem is.
Best of luck.

Have just found a hickup on the Lion software 10.7.2 When using a access point that you name with letters that is only in Norwegian æøå you will loose connections and only get time out. So the solution will be to rename the access point.

Any solution beside to rename the wifi access point without the spesial Norwegian letters æøå?

Your points match mine pretty well,though here are some thoughts:
1. I thought about this theory myself this morning (iTunes possibly causing more issues), but I haven't been able to verify it.
2. When I set up a new user it seemed better for a while, but the issue croppped back up. Yesterday I fully wiped the machine and reinstalled from scratch. I did not reimport my user from TimeMachine, but the problem has come back. My thinking was that I might have some really old software or prefs hanging around causing the issue. No dice.
3. This is my current theory of the issue, so my next step will be to pull the RAM from Crucial and see how the system behves. IF that doesn't eliminate the problem, I'll pull the factory installed RAM and replace it with the 3rd party RAM. The odd thing is how many people seem to have similar issues - I know two personally, and have seen several posts on forums. I think the most common point for this happening was the 10.7.2 update, which would point to software as the culprit.
4. That matches my experience.
My hope is that this will be repaired in the forthcoming 10.7.3 release (current production version is 10.7.2), but otuside of what I noted above, I'm at a loss.

Opportunity save times out ...Large entries in PPFTTRIGG for this opportuni

Hello,
We are working on CRM Opportunities..
Editing the opportunity is possible, but when this opportunity is saved, it times out..
There are a set of these opportunities for whom it is timing out...
For these opportunities, there are a lot of entries in the table 'PPFTTRIGG' - actions table..
Trying to process the messages using the report 'RSPPFPROCESS' is timing out again for these opportunities
We have action definitions for opportunities (if opportunity has not been updated , opportunity expired etc ) to trigger email alerts ...which are sitting in the PPFTTRIGG table.
Do you know a workaround or a solution for enabling the saving of the above opportunities..
Any advise is greatly appreciated..
Thanks.
Regards,
Monica
Edited by: Monica Turner on Aug 16, 2011 11:10 AM

HI Monica,
You may skip determine of Actions for certain opportunities in the badi's like
CONTAINER_PPF
EVAL_SCHEDCOND_PPF
EVAL_STARTCOND_PPF
This is just an idea, i never tried this, May be you can explore in this angle.
-Satish

When is it possible to have the same User Interface for all screensizes?

Hi all, i am final year student doing some research about User Interface Fragmentation on Mobile devices. As we already know, there are a huge variety of mobile screen sizes, and usually to provide users the best experience interfaces, we often have to customize the UI of one application in one phone to another. So i wondered when it is OK to have the same UI for all screen sizes?
Thanks.

It's usually OK if you don't use CustomItem, avoid extra-long Strings in titles etc. You might also need to scale any Canvas / GameCanvas graphics and Images using a scaling factor computed from the detected screen size.
I have 3 applications for free download from GetJar.com (search "Colorz") which have only the one version for all MIDP 2.0 devices, and there have been no complaints in a combined total of over 11,000 downloads ;-)
In any case, UI diversity is the least of the headaches any j2me developer faces, there are many features of j2me that are unimplemented or incorrectly implemented on various devices. Even the CLDC reference implementation has unaddressed bugs.
luck, db

Find out more about the latest software update for...

As you might have noticed, the latest software update for the Nokia Lumia 920 and Lumia 820 has already started to roll out to many countries and for various operators. The software update deliveries are expected to be completed by March, and if your phone is applicable for the update, you will see the update notification on your phone’s screen.
Thank you to those of you who have given us feedback on this release. We are listening to you, and acknowledge that while we have enhanced the performance of many features, we are still working on others. This update (to version 1232.5951.1249.10xx) offers the following improvements:
More efficient Messaging experience. After the update, you can:
save draft messages
edit forwarded multimedia messages
select multiple recipients at once
respond to a call with a text message
Improved performance for Bluetooth
Imaging enhancements
Web browsing. You can now change your settings to prevent pictures from downloading automatically and delete specific sites from your history
Better control of data costs: you can prevent automatic fallback from a Wi-Fi network to a mobile data network and keep Wi-Fi always on to off-load network usage to Wi-Fi.
As part of our continuous improvement and development process, we will continue to deliver further improvements with future software updates. In case you haven’t updated your phone software before, see this Nokia support page for useful instructions on how to receive and install an update on your Nokia Lumia phone.

Do you mean "panache"?
Submit your feedback directly to Apple using the appropriate link on the Feedback page:
http://www.apple.com/feedback

The external number range for Equipment master

Dear Experts,
My client has requirement to use KKS code as Equipment number as they want to create Notification and Maintenance order using the KKS code.
For example 10H, 10BEB, 20BHB04, 10LBG10AA001, 10HLA13AA001A, 10ETG10AN001-E etc.
All these KKS codes has different character length hence it's not fit in any number range.
can anyone suggest the external number range that I can use for above requirement?
Thanks.

Parag,
I have checked again. It is working correctly. Remember that the following setting the check box below the column A should be empty. This allows Alphanumeric characters in the numbers.
SPRO Path to above setting
My Equipment category of External Numbers is 'A'.
KJogeswaraRao

Time-out limit of the 8451-I2C interface for hold-master condition

Similar Messages

Maybe you are looking for