Timecapsual wireless connection unable to set up
I have a 1TB timecapsuale connected to my Mac with a cable. Everything works fine. I now want to connect the time capsuale with wireless instead of the cable and also use the timecapsuale as a repeater for my Router. Unfortunately I can't get this to work. Anyone who could point me into the right direction?
TC can only repeat another apple router. Is the other router Airport Extreme, Express or another TC.. if not, no it won't work.
You can use wireless.. Just setup TC to create a wireless network and set the airport in the computer to join to it.
Similar Messages
-
Wireless connection unable to automatically connect
My wireless router is working perfectly as other devices are having no trouble connecting wirelessly. My HP LaserJet CP1525nw will not find the wireless connection for wireless printing. Apparently HP does not support these problems unless the warranty is current. I am NOT a techy, so I am lost for how to proceed. I have tried to follow the instructions for connection displayed int he window of the printer, no success. HELP please
Hi @alice12,
I understand that you are unable to setup the printer over the wireless network. I can help you with this.
Restore the factory settings on the printer.
Press the OK button on the printer, go to service, then select restore defaults.
Print a configuration page from the printer to make sure the IP and SSID are cleared.
Printing a Configuration Report.
Select Method one under Windows.
I have provided a document for setting up the wireless connection or you can follow my different methods provided.
Installing the Printer Software on a Wireless or Wired (Ethernet) Network.
Method One:
To connect your wireless printer to your wireless router using WPS:
(your router would have to support WPS)
Start the WPS push button mode on your printer.
Within 2 minutes, press the WPS button on your router.
Then run add a printer wizard in devices and printers.
Method Two:
Uninstall the printer software.
Insert the software CD into the CD drive.
Follow the on-screen instructions.
When prompted, select the Connect through a wireless network option.
Method Three:
Connect the printer to the router with a Ethernet cable.
Wait about 1 minute and the printer should have a valid IP address.
Print the configuration page to get the printer's IP address.
Type the IP address into Internet Explorer address bar which should open the printer's embedded web services page.
Setup the wireless through here now.
Click on the networking tab, wireless on the left, fill out the network information and apply the settings.
After the confirmation, then disconnect the Ethernet cable.
Now you should have a blue wireless light on the printer in about 1 minute.
Run the add printer wizard through devices and printers to install the printer.
What operating system are you using? How to Find the Windows Edition and Version on Your Computer.
If you need further assistance, just let me know.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP -
Wireless problems Unable to set key / freq Invalid argument??
trying to get wireless up on my dell mini 9
i am able to scan ap's but whenever i try to connect i get the following
sudo iwconfig eth0 essid Myessid key 101993D8SA77ADFetcetc
Error for wireless request "Set Encode" (8B2A) :
SET failed on device eth0 ; invalid argument.
any ideas on this?
thanks!
EDIT: some info
my wireless 128 bit 64 hex digits
broadcasting on channel 6 (2.437G freq)
rc.conf
eth0 = "dhcp"
eth1 = "dhcp"
wlan_wlan0="etho essid myessid key MYKEY
INTERFACES=(eth1 wlan_wlan0)
[jxxx@myhost ~]$ sudo iwconfig eth0 essid myessid key MYKEY
Password:
Error for wireless request "Set Encode" (8B2A) :
SET failed on device eth0 ; Invalid argument.
[xxx@myhost ~]$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:23:08:1C:35:9B
inet6 addr: fe80::223:8ff:fe1c:359b/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:72484
TX packets:0 errors:67 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:17
eth1 Link encap:Ethernet HWaddr 00:21:70:D2:7B:3C
inet addr:192.168.1.103 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::221:70ff:fed2:7b3c/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:3427 errors:0 dropped:0 overruns:0 frame:0
TX packets:2074 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2862996 (2.7 Mb) TX bytes:337371 (329.4 Kb)
Interrupt:40 Base address:0xc000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:12 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:820 (820.0 b) TX bytes:820 (820.0 b)
[xxx@myhost ~]$ iwconfig
lo no wireless extensions.
eth0 IEEE 802.11 Nickname:""
Access Point: Not-Associated
Link Quality:5 Signal level:199 Noise level:199
Rx invalid nwid:0 invalid crypt:0 invalid misc:0
eth1 no wireless extensions.
[xxx@myhost ~]$
Last edited by murfMan (2011-03-27 19:20:47)Hi,
I had the same problem with my tx2z and broadcom-wl. After reinstalling the wl and trying to enter the key as a string "key s:XXXXXXXXXX" I had a look at the key setup using iwlist:
[alpha@myhost ~]$ sudo iwlist eth0 key
eth0 4 key sizes : 40, 104, 256, 128bits
4 keys available :
[1]: off
[2]: off
[3]: off
[4]: off
Current Transmit Key: [1]
from there I decided to manually state the key rather than allowing implicit decleration. Hence writing:
[alpha@myhost ~]$ sudo iwconfig eth0 essid BTHomeHub-XXXX key [1] XXXXXXXXXX
rather than the error producing:
[alpha@myhost ~]$ sudo iwconfig eth0 essid BTHomeHub-XXXX key XXXXXXXXXX
This produced no errors and allowed the connection. Hope this helps, and sorry for lack of technical understanding (it were a bit of trial and error and have only recently started with arch).
Also, if it helps, my rc.conf section is as follows:
INTERFACES=(eth0)
and my ifconfig and iwconfig are:
[alpha@myhost ~]$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:21:00:73:C6:A8
inet addr:192.168.1.72 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::221:ff:fe73:c6a8/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:35665 errors:0 dropped:0 overruns:0 frame:902
TX packets:23215 errors:6 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:42574425 (40.6 Mb) TX bytes:2772313 (2.6 Mb)
Interrupt:17
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:112 errors:0 dropped:0 overruns:0 frame:0
TX packets:112 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:8584 (8.3 Kb) TX bytes:8584 (8.3 Kb)
[alpha@myhost ~]$ iwconfig
lo no wireless extensions.
eth0 IEEE 802.11 Nickname:""
Access Point: Not-Associated
Link Quality:5 Signal level:204 Noise level:165
Rx invalid nwid:0 invalid crypt:0 invalid misc:0
eth1 no wireless extensions. -
Printing over wireless connection
How would you set up a powerbook to print over a wireless connection? I set up a wireless network for my mom (she had a Dell Inspiron8600) when I passed on my PowerBook to her. Wireless internet connection is working fine. The main unit connected to the modem is the Inspiron. I can't seem to figure out what I have to do to get the PowerBook to print. If someone could walk me through the setup process I would sure appreciate it! The printer hooked up to the Inspiron is an HP Deskjet 5470. It is not being recognized by the PowerBook.
Make sure you have the latest drivers on your Mac and make sure the printer is shard on your pc. Go to system preferences on your mac click on "printer/fax" click on the + sign. Then go to "more printers" then find your printer on your network.
This technique has gotten my mac to communicate with my printer, but not actually print but maybe it will be successful for you.
EAH22 -
Managing wired and wireless connections.
I have a client who wants to be able to use a wireless hotspot for backup internet when their main connection fails.
However when the main internet fails, they can't always use the wireless connection they've set up while still being on the wired LAN. The workstation will ignore the wireless connection and attempt to connect to the internet via LAN.
1. They need the LAN for networked printers
2. They want to be able to use the wireless hotspot to connect to the internet.
3. They want to be able to switch between connections without their users needing to change anything manually other than connecting to the wireless hotspot.
I've been looking but I haven't been able to find any kind of software that manages network connections in this way.
Is anyone able to suggest a solution?Hi,
You can setup as shown on page #7 of tyhe following guide:
http://www.hp.com/ctg/Manual/c00389927.pdf
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem. -
[SOLVED] Unable to set up wireless connection (wiki read)
Well, as you can see that's my 1st post. That's why I want, at first, congratulate the community for the amazing wiki and forums. It helped so much.
But I'm writing here because I have a problem that I'm unable to resolve with the wiki: The wireless connection. It doesn't work.
Now I will post my hardware and some software:
ASUS Eeepc 1000
01:00.0 Network controller: Ralink corp. RT2860 (as # lspci | grep -i net says)
03:00.0 Ethernet controller: Atheros Communications AR8121/AR8113/AR8114 Gigabit or Faster Ethernet (rev b0) (as # lspci | grep -i net says)
Linux Kernel 3.2.4-1-ARCH (as # uname -r says)
I3 window manager
wireless_tools and wpa_supplicant installed
(If you want to know something more, ask me)
The wireless is enabled in the BIOS and the led indicator is on.
Being the network controller RT2860, must I do something special? I tried to blacklist what the wiki says with no results.
I have no problems with wired connection, but I can't set up my wireless connection with the # ip link set wlan0 up command (and yes, I execute this command as su or with sudo). I3 corroborates it in the status bar: W: down.
# ip link list
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
( I had it disconnected when I did this check)2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000 link/ether 00:22:15:08:af:e2 brd ff:ff:ff:ff:ff:ff
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000 link/ether 00:15:af:ba:39:b8 brd ff:ff:ff:ff:ff:ff
I tried a lot of thing, but no results at all. Must I configure manually some file like wpa_supplicant.conf, rc.conf or others? It is normal that in rc.conf, NETWORKING tab, the only interface is eth0 (interface=eth0) with no other references to wlan0?
Thanks for your attention.
Last edited by Agravain (2012-02-20 17:42:52)That thing on the wiki about blacklisting is probably outdated, it's from the times the kernel had two Ralink drivers. Now there's only one, and you should not blacklist anything.
rc.conf is only for wired interfaces. For wireless you can do stuff manually, or use a manager - netcfg, wicd, networkmanager.
And that's that. For further help, you'll have to provide details about which commands you used and what their output is.
Last edited by Gusar (2012-02-20 16:15:04) -
Unable to set wireless connection with imac and Canon MX860 printer ...
I recently converted to a Mac and bought a Mac Book, iMac, Airport Extreme, and a Canon MX860 printer. i have installed the canon software numerous times on my iMac to set up the wireless connection. yes, the airport extreme recognizes the printer and i am able to connect to my private and guest networks. the signal strength is good. It's the next part that I'm always stuck at. The Printer settings does not display when i choose More Printers and select Canon IJ Network. I called Apple support and we tried changing my network settings to an unsecured network and it still has the same issue. It was recommended this may be Canon driver issue and advised me to contact Canon. I reset the Airport, changed my network name and password .. i think i tried everything and it still does not work. What was I thinking when i said i wanted to convert to Mac? I can't move forward and connect my macbook or pc yet until I successfully connect the imac. Yes, i installed the latest canon IJ Network tool. of course the USB connection is fine but that defeats the whole purpose if why i bought this printer. please advise how to fix. this is getting very frustrating.
Some help at http://store.apple.com/us/product/TV352LL/A perhaps in the comments.
And maybe at http://www.amazon.com/Canon-PIXMA-MX860-Wireless-Printer/product-reviews/B001R4C 5BK in the comments.
"I ran into the same network installation issue that I've seen in other Canon printers. Canon's network setup forces you to connect by USB cable first. Only after you tell the program that you want to use the computer over the network can you remove the USB cable, move the printer if needed, and if you're using a wired connection, reconnect a network cable. The process isn't particularly difficult, but it's more cumbersome than what other printers let you do, which is simply put the printer where you want it, plug in an Ethernet cable, and install the software." source = http://shop.pcmag.com/shop/product/pcmag/84634068.aspx?SB=6&OB=1
"MAC wireless network printer setup requires turning off firewall, and works fine if you leave firewall off (not recommended). If you set firewall at "essential connections only," wireless networked MX860 won't work. You must add MP navigator and solution apps to your firewall enabled list. Then it worked fine on the admin account, but still won't work on users account which required additional permission settings and selections. After 2 hours it worked fine, but I would've expected better instruction manual for MAC." source = http://cnet.nytimes.com/multifunction-devices/canon-pixma-mx860/4852-3181_7-3352 9769.html
"The only trouble that I have had with this machine is setting up the wireless network. The manual instructions are impossible for me to understand and I ended up having to call for assistance. Which easily solved the problem. And again when I had to reconfigure my network settings it was impossible to follow the logarithm of instructions in the manual. Again I needed to call for assistance. If I need help after the year manufacture's warranty I will be charged for these calls." source = http://www.zimbio.com/InkjetPrinter+Reviews/articles/1932/Canon+PIXMA+MX860+Wireless+One+PhotoPrinter
Even Windows people have trouble:
"I NEED INTRUCTIONS ON HOW TO CONNECT MY HP LAPTOP TO THE CANON MX860 PRINTER."
"I'm with you. I have my mx860 connected usb to my pc with the printer being shared but my wireless laptop can't find it no matter what I try."
And, unhappy Vista person:
"I had high hopes for this printer - it seemed to have it all. But the wireless feature never worked, it only worked on my gigabit network for about two weeks (only THREE print jobs including the test print), and never observed it to work via USB - Vista (x64 Ultimate) would throw an error saying it could not attach the device." -
my Ipad and itouch cannot be connected ti wireless router tried changing setting still cannot connect
Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
• Launch Settings app
• Tap on Wi-Fi
• Tap on the blue arrow of the Wi-Fi network that you connect to from the list
• In the window that opens, tap on the Renew Lease button
6. Potential Quick Fixes When Your iPad Won’t Connect to Your Wifi Network
http://ipadinsight.com/ipad-tips-tricks/potential-quick-fixes-when-your-ipad-won t-connect-to-your-wifi-network/
~~~~~~~~~~~~~~~~~~~~~~~~~
Wi-Fi Fix for iOS 6
https://discussions.apple.com/thread/4823738?tstart=240
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Boost Your Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Boost-Your-Wi-Fi-Signal.h tm
Troubleshooting a Weak Wi-Fi Signal
http://ipad.about.com/od/iPad_Troubleshooting/a/Troubleshooting-A-Weak-Wi-Fi-Sig nal.htm
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
Cheers, Tom -
How to set up WRT54GS so the wired and wireless connections both work?
I have a DSL line in to a Motorola modem.
The modem is connected to the WRT54GS with an ethernet cable.
When I connect my computers directly into the WRT54GS with an ethernet cable (there are four connection spots at the back of the box), I cannot go to the internet. I have 3 computers plugged in, but none of them connect via Ethernet..
Is there a setting on the router so that I can use the router for both wired and wireless connectivity?
Added info: I tried to connect directly from the computer to the modem, but again, got no connectivity. When I "chatted" with ATT, they told me the modem is set to "bridge", and that I could connect only one device. I don't want to change this setting because I want to use the router for the wireless capability. Besides which, I have more than one computer to connect to the internet.
How come I cannot just plug in and go?
My firmware version is v2.07.1.
I don't know how to find out what hardware version I have.
Other info is "DirectEthernet Connection, Speed: 100.0 Mbps, Signal Strength: Excellent, Status: Connected"
Also "1394 Connection 3, Speed: 400.0 Mbps, Status: Connected"
I don't know what that's for, but thought it might prove useful to those of you who are knowledgeable about such things.
Wireless is ok, but if I'm sitting right next to the router, I'd like to connect with Ethernet and take advantage of the better speed, etc.
Thanks in advance.Just click this link.
-
Unable to wirelessly connect to printer after switching ISP providers
I recently moved and needed to change ISP providers. My Mac is up and running wirelessly on the new network, but I can't seem to configure my HP printer. Model: HP LaserJet P1102w. Mac OS: X. Problem details: Wireless icon blinks for several seconds, then turns off. Attempted to setup wireless connection using Finder, then Applications, then System Preferences, then Print & Fax, then Open Print Queue. When I click on Utility, there is no option for HTMLConfig. Also, unable to find instructions for printing network configuration page or performing wireless network test. This printer was working successfully, wirelessly, at my former home. Thank you in advance for your help!
It sounds like the printer just needs to be added to the new network.
Uninstall the printer software completely and follow the steps for your OS X version in this document from HP.
What OS X version is being used?
What brand and model is the router?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓ -
Can't set up wireless connection for HP C4385 All-In-One with Windows 7.
Hi guys,
I just got a new laptop with Windows 7 64 bit. I already had an HP C4385 All-In-One that I was using with my last computer. I have also just set up a new wireless network because I got a new cable provider. So basically I needed to do everything from the beginning.
When I inserted the setup CD and ran the setup program, it said I couldn't continue because my OS was not supported. I went to the HP website and found the solution, which was to plug the printer in via USB and let Windows Update find the latest driver. Ok, that's fine, the printer works now when the USB cord is plugged in.
To set up the wireless connection, the instruction manual says I need to do it through the network setup wizard p on the CD. But that brings me back to my original problem-- the setup CD won't work because it doesn't recognise Windows 7.
So my question is-- how can I update the network settings (SSID and key) on the printer without the network setup wizard?
Thanks for any help, this is really driving me crazy!Download from hp.com here.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP -
Unable to access wireless connection with linksys rooter WRT54GS
Hi,
I just installed a wireless rooter Linksys WRT54GS on my connection, The problem I have is being able to access it with my wireless on my laptop.
I kept getting a message stating "connection unindentified" "access limited". I've done most of what is already suggested on your forum such has turning the power off of my rooter, my modem and such and still nothing. I'm able to access the wireless with my girlfriend Mac Notebook, my playstation 3 and my desktop computer which uses Windows X. First I thought that it my be a problem with my security but even when the connection is unprotected I still get that error. I try to disable the IpV6but that didn'tdo anything either.
My laptop is a Toshiba Qosmio X300 PQX32C-033019 with Vista and my rooter is a Linksys WRT54GS vers. 6
Here's my connection log, sorry if it's in French:
Informations sur l'ordinateur
Vendor:TOSHIBA
Machine Name:Qosmio X300
VersionQX32C-033019
CPU Maker:GenuineIntel
CPU Name:Intel(R) Core(TM)2 Duo CPU P8400 @ 2.26GHz
CPU Clock:2267
CPU Base Clock:2267
OS:Microsoft® Windows Vista™ Édition Familiale Premium
OS Build:6001
OS SPervice Pack 1
Ram:4188120
Début de la page
Informations IP
ipconfig /all
Configuration IP de Windows
Nom de l'h“te . . . . . . . . . . : PC-de-ThomasMur
Suffixe DNS principal . . . . . . :
Type de noeud. . . . . . . . . . : Mixte
Routage IP activ‚ . . . . . . . . : Non
Proxy WINS activ‚ . . . . . . . . : Non
Liste de recherche du suffixe DNS.: phub.net.cable.rogers.com
Carte r‚seau sans fil Connexion r‚seau sans filÿ:
Suffixe DNS propre … la connexion. . . :
Description. . . . . . . . . . . . . . : Intel(R) Wireless WiFi Link 5100
Adresse physique . . . . . . . . . . . : 00-21-5D-3D-9C-08
DHCP activ‚. . . . . . . . . . . . . . : Oui
Configuration automatique activ‚e. . . : Oui
Adresse IPv6 de liaison locale. . : fe80::a9d9:4618:2ae4:d7e5%11(pr‚f‚r‚)
Adresse d'autoconfiguration IPv4 . . . : 169.254.215.229(pr‚f‚r‚)
Masque de sous-r‚seau. . . .ÿ. . . . . : 255.255.0.0
Passerelle par d‚faut. . . .ÿ. . . . . :
Serveurs DNS. . . . . . . . . . . . . : fec0:0:0:ffff::1%1
fec0:0:0:ffff::2%1
fec0:0:0:ffff::3%1
NetBIOS sur Tcpip. . . . . . . . . . . : Activ‚
Carte Ethernet Connexion au r‚seau local :
Suffixe DNS propre … la connexion. . . : phub.net.cable.rogers.com
Description. . . . . . . . . . . . . . : Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Adresse physique . . . . . . . . . . . : 00-1E-EC-3F-7B-CF
DHCP activ‚. . . . . . . . . . . . . . : Oui
Configuration automatique activ‚e. . . : Oui
Adresse IPv6 de liaison locale. . : fe80::4da:b21b:843c:7bfd%10(pr‚f‚r‚)
Adresse IPv4. . . . . . . . . . . : 192.168.1.100(pr‚f‚r‚)
Masque de sous-r‚seau. . . .ÿ. . . . . : 255.255.255.0
Bail obtenu. . . . . . . . .ÿ. . . . . : 8 juin 2009 18:11:58
Bail expirant. . . . . . . . .ÿ. . . . : 9 juin 2009 18:11:58
Passerelle par d‚faut. . . .ÿ. . . . . : 192.168.1.1
Serveur DHCP . . . . . . . . . . . . . : 192.168.1.1
Serveurs DNS. . . . . . . . . . . . . : 64.71.255.198
NetBIOS sur Tcpip. . . . . . . . . . . : Activ‚
Carte Tunnel Connexion au r‚seau local* :
Statut du m‚dia. . . . . . . . . . . . : M‚dia d‚connect‚
Suffixe DNS propre … la connexion. . . : phub.net.cable.rogers.com
Description. . . . . . . . . . . . . . : isatap.phub.net.cable.rogers.com
Adresse physique . . . . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP activ‚. . . . . . . . . . . . . . : Non
Configuration automatique activ‚e. . . : Oui
Carte Tunnel Connexion au r‚seau local* 6 :
Statut du m‚dia. . . . . . . . . . . . : M‚dia d‚connect‚
Suffixe DNS propre … la connexion. . . :
Description. . . . . . . . . . . . . . : Carte Microsoft ISATAP #2
Adresse physique . . . . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP activ‚. . . . . . . . . . . . . . : Non
Configuration automatique activ‚e. . . : Oui
Début de la page Informations de routage
route print
===========================================================================
Liste d'Interfaces
11 ...00 21 5d 3d 9c 08 ...... Intel(R) Wireless WiFi Link 5100
10 ...00 1e ec 3f 7b cf ...... Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
1 ........................... Software Loopback Interface 1
13 ...00 00 00 00 00 00 00 e0 isatap.phub.net.cable.rogers.com
12 ...00 00 00 00 00 00 00 e0 Carte Microsoft ISATAP #2
===========================================================================
IPv4 Table de routage
===========================================================================
Itin‚raires actifsÿ:
Destination r‚seau Masque r‚seau Adr. passerelle Adr. interface M‚trique
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.100 20
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
169.254.0.0 255.255.0.0 On-link 169.254.215.229 281
169.254.215.229 255.255.255.255 On-link 169.254.215.229 281
169.254.255.255 255.255.255.255 On-link 169.254.215.229 281
192.168.1.0 255.255.255.0 On-link 192.168.1.100 276
192.168.1.100 255.255.255.255 On-link 192.168.1.100 276
192.168.1.255 255.255.255.255 On-link 192.168.1.100 276
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.1.100 276
224.0.0.0 240.0.0.0 On-link 169.254.215.229 281
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.1.100 276
255.255.255.255 255.255.255.255 On-link 169.254.215.229 281
===========================================================================
Itin‚raires persistantsÿ:
Aucun
IPv6 Table de routage
===========================================================================
Itin‚raires actifsÿ:
If Metric Network Destination Gateway
1 306 ::1/128 On-link
10 276 fe80::/64 On-link
11 281 fe80::/64 On-link
10 276 fe80::4da:b21b:843c:7bfd/128
On-link
11 281 fe80::a9d9:4618:2ae4:d7e5/128
On-link
1 306 ff00::/8 On-link
10 276 ff00::/8 On-link
11 281 ff00::/8 On-link
===========================================================================
Itin‚raires persistantsÿ:
Aucun
Début de la page Informations de protocole
Protocol Bind Information
SSTP based VPN
Microsoft TCP/IP version 6 - Tunnels
isatap.{DF6498ED-F5F7-4E96-9496-10C8BB95FA20}
isatap.phub.net.cable.rogers.com
Internet Protocol (TCP/IP) - Tunnels
Microsoft NetbiosSmb
Internet Protocol Version 4 (TCP/IPv4)
Intel(R) Wireless WiFi Link 5100
Internet Protocol Version 4 (TCP/IPv4)
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Internet Protocol Version 6 (TCP/IPv6)
isatap.{DF6498ED-F5F7-4E96-9496-10C8BB95FA20}
Internet Protocol Version 6 (TCP/IPv6)
isatap.phub.net.cable.rogers.com
Internet Protocol Version 6 (TCP/IPv6)
Intel(R) Wireless WiFi Link 5100
Internet Protocol Version 6 (TCP/IPv6)
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Remote Access IP ARP Driver
Miniport WAN (IP)
Message-oriented TCP/IP Protocol (SMB session)
WINS Client(TCP/IP) Protocol
Internet Protocol Version 4 (TCP/IPv4)
Intel(R) Wireless WiFi Link 5100
Internet Protocol Version 4 (TCP/IPv4)
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Internet Protocol Version 6 (TCP/IPv6)
isatap.{DF6498ED-F5F7-4E96-9496-10C8BB95FA20}
Internet Protocol Version 6 (TCP/IPv6)
isatap.phub.net.cable.rogers.com
Internet Protocol Version 6 (TCP/IPv6)
Intel(R) Wireless WiFi Link 5100
Internet Protocol Version 6 (TCP/IPv6)
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Internet Protocol Version 6 (TCP/IPv6)
isatap.{DF6498ED-F5F7-4E96-9496-10C8BB95FA20}
isatap.phub.net.cable.rogers.com
Intel(R) Wireless WiFi Link 5100
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Internet Protocol Version 4 (TCP/IPv4)
Intel(R) Wireless WiFi Link 5100
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Remote Access IPv6 ARP Driver
Miniport réseau étendu WAN (IPv6)
Point to Point Protocol Over Ethernet
Intel(R) Wireless WiFi Link 5100
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Point to Point Tunneling Protocol
Layer 2 Tunneling Protocol
Remote Access NDIS WAN Driver
WAN Miniport (SSTP)
Carte asynchrone RAS
Miniport WAN (PPPOE)
Miniport réseau étendu WAN (PPTP)
Miniport réseau étendu WAN (L2TP)
Link-Layer Topology Discovery Mapper I/O Driver
Intel(R) Wireless WiFi Link 5100
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Link-Layer Topology Discovery Responder
Intel(R) Wireless WiFi Link 5100
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
NDIS Usermode I/O Protocol
Intel(R) Wireless WiFi Link 5100
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Début de la page Informations sur les équipements
Realtek RTL8168C/8111C Family PCI-E Gigabit Ethernet NIC (NDIS 6.0)
Device ID : PCI\VEN_10EC&DEV_8168&SUBSYS_FF001179&REV_02\4&492937F&0&00E2
Status : Enable
Driver Vender : Realtek
Driver Version : 6.205.403.2008
Driver Date : 4-3-2008
Intel(R) Wireless WiFi Link 5100
Device ID : PCI\VEN_8086&DEV_4232&SUBSYS_12018086&REV_00\4&3905AE0C&0&00E3
Status : Enable
Driver Vender : Intel
Driver Version : 12.0.0.73
Driver Date : 4-27-2008
Bluetooth
Device ID : ACPI\TOS6205\5&F592293&0
Status : Disable
Bluetooth Version : v6.10.07.2(T)
Début de la page Statut du commutateur de communications sans fil et de la touche d'accès direct pour réseau sans fil
Wireless Communication Switch : On
Wireless Hotkey (Fn + F8)
Wireless LAN : On
Solved!
Go to Solution.Try this -
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...
Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...
Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
On your Vista Laptop, first disable the Wireless Network Connection and restart the Laptop, then Enable the Wireless Connection...
Then Click on Start >> Control Panel >> Network and Sharing Center >> Manage Wireless Network and click on Add, select Manually Create a Network Profile and click Next, enter your Network SSID/Network Name, select WEP for Security type and enter your 10 digit Network Key and click on Next, it should say "Successfully Connected to ____" close all the Windows and restart the Laptop, now see if you can connect to Internet Wirelessly... -
new itouch user here, We had a wireless connection with a password all set up but we couldn't remember the password meanwhile there are other connections around us but locked. So i decided to make a new one yet it still will not allow to go on safari after i type in the password PLEASE HELP ive turned on and off etc
My guess is that the security settings on your router and iPod do not match.
For a test, change your router so there is no security. See if you can connect and get to the Internet. If that works, set up the router with security and use the same settings for the iPod. -
Unable to obtain ip with wireless connection to Netgear WGR614 router
Pardon my ignorance, I'm relatively new to the Mac world.
I recently purchased an iMac and at the same time purchased a Netgear wireless router.
When hardwired to the Netgear, I have no issues. I tried connecting via wireless, and keep getting the self-assigned ip address. My wireless network is detected and the Airport card connects...full strength. I also have a laptop running windowsXP, and it connects with no issues.
I have tried some of the suggestions mentioned in the discussions. Power cycled the Netgear. Changed channels...from 11 to 10. That didn't help so I went back to channel 11. I have security disabled...trying to keep the configuration as simple as possible until I can get this working.
If anyone can share some thoughts/ideas, it would be greatly appreciated.
Thanks.
-TimI had to go into /Library/Preferences and dragged SystemConfiguration to my desktop. I restarted the iMac.
After it booted up, I went into System Preferences => Network; created a new Location and used the "Assist Me" tab at the bottom. It walked me through setting up the Airport again and this time it worked.
For anyone that does this, once you confirm your wireless connection is working, take the SystemConfiguration on the desktop and drag it to the Trash. -
Is there any way to use a MacBook Pro as a router to set up a wireless connection for XBOX live.
Is there any way to use a MacBook Pro as a router to set up a wireless connection for XBOX live.
Mac OS X 10.6 Help: Sharing your Internet connection
Maybe you are looking for
-
How do I turn off Air Drop on my MacBook Pro?
Realy don't like the idea of my MacBook being available to people around me.
-
Hi I have uploaded files before but not using jquery but now am trying to use jquery so that my files uploads without page refreshing. This is my Jquery code. and below is the html code. Can any one help me with the jquery code so that I can get the
-
In FCS2 what is the best way to convert an avi file shot in 16:9 to match media shot in 4:3 dv. I don't have access to the original footage, and a vast amount of footage from different times is being used however it is all captured correctly. How wou
-
Usb devices cash mac book pro?
hi i recently did a system update on my mac. after doing so when i try to plug the usb cabel to my printer or a flash drive into my computer a dark veil comes down telling me to restart my computer. However if i plug in my ipod it works perfectly fin
-
I am developing a 16 channel data acquistion application using a cDaq9184 with a 9205 module. So far, I have one DaqTask set up in my .NET project along with one DaqComponent on the form for setting up the first AI channel. Each channel will have i