Timecode error in batch capture

I've searched this problem but still haven't found an answer. When I batch capture, I get a "Timecode error" and on about half the clips I logged I have to cancel out of the capture. some work,some don't. It's not a problem with the pre-roll at the beginning of the tape; I left plenty of room when I set the in/out, and the first clip is now captured anyway so it can't be the start of the tape. But every time I try to capture the rest of the clips, I get this error with some if not most of them. I've changed the setting to NDF and it doesn't seem to make a difference. I'm only capturing in the middle of the tape now, so the beginning and end have lots of space. Please someone tell me how to stop this! I just upgraded to Pro and it's my first attempt at batch capture, so I'm pretty disappointed that it's such a waste of time.
Thanks, smart people!

Great, now you made Studio go and have some fun on the weekend.
X is right eliminate things one at a time.
You didn't let us know what drive you are capturing to.
If capturing from the camera doesn't work, it may be that you are experiencing the "multiple FW devices on one FW bus issue" in which case you might try looping the camera or deck through the drive, works for some, but more likely you will need to install another FW bus via the card slot on the laptop.
By the way, this really doesn't sound like a drop/non drop issue, but look at the timecode display of the footage on tape. If the last 2 numbers are preceded by a semicolon,,, it's drop frame.
Now, I believe someone mentioned the US Open!
rh

Similar Messages

Timecode changes when batch capturing

I am capturing betacam sp footage into FCP 5.1 on a dual G5 2.3 box, and using a Kona LSe card. Timecode is running through the 422. For the most part, things are going smoothly, but I am now running into an issue where when I batch capture my logged clips, the last 10 to 15 sec. is chopped off. I generally can just enter the time code again manually to fix the issue, but some of my clips are 8 to 10 min long (interviews), and my client is getting irritated that we are having to capture them again. I also tend to batch capture the majority of these long bites overnight for next morning's session, and they are now consistently coming in with the ends lopped off. FCP is actually changing the timecode on the clip, making me question whether or not I entered it correctly the first time. To prove that I'm not crazy, I monitored the capture on the first couple of clips, and sure enough, FCP decides that I don't need the last 15 sec of my clip, and changes the timecode accordingly during the capture.
What's going on? Is it the Kona card or its software? Thanks.

Well I recently had a similar problem that is really driving me crazy.
While capturing 720p 59.94 from the D5
In FCP when I log a clip at:
01:20:00:00 in
01:20:30:00 out
After Batch Capture is complete the clip shows up in the browser as:
01:19:55:05 in
01:20:25:05 out
FCP is effectively changing the logged timecode of the clip.
In all my experience with FCP I have never encountered this issue and I am completely puzzled. I've contacted AJA and they have said that they do not know of this issue and were puzzled also. The only thing about my current configuration that is not completely right is that I am not using a Tri-Level Sync at the moment. We get ours tomorrow. AJA suggests using the Tri-Level Sync with the Kona 3 card, but would that cause a glitch of this nature? I will try again tomorrow of course and update, but does having bad 720p reference effect how FCP logs and handles TC? To my knowledge it shouldn't and makes me think that there may be some sort of FCP error occurring. There is no reason why FCP should be changing my logged clip settings. Also, I tried a test where I made the clip that came in with the bad timecode offline, and then ran a Bath Capture again, and it changes the logged timecode even further. I've tried a variety of Device Control settings playing with frame offset etc with all having the exact same numeric result (see TC above).
Anyone who has any insight or similar experience your thoughts are greatly appreciated. Thanks for the help
Ted - Editor, NYC

"No Video" error when Batch Capturing

I am getting a new error that I have not seen before when using Batch Capture in FCP. It cues the tape, starts the pre-roll and then spits out an error message that there is "no video". Of course, there is video.
The same thing does not happen when capturing one clip at a time nor does it happen if you capture live (hitting Capture "Now" in L&C window).
Any thoughts?

I also don't want to keep paying $23 a month for software that is not 100%.
Software as complex as Premiere Pro will never be 100% bug free.
I'm also inclined to believe this is more of a system issue than a PP issue. I don't recall other reports of this nature, and it works fine on my own system.
The only other thing I can think of to suggest is another FireWire port, possibly by adding a FireWire card to the system. I've read that the chip makes a difference, so research over in the Hardware forum.

Logged Timecode Changes after Batch Capture

I'm working with the Kona 3 and the Panasonic D5 (HD3700B)
I'm having a problem with FCP changing my logged clip TC after Batch Capture in 720p 59.94. This problem only occurs in 720p mode, 1080i is just fine.
While capturing 720p 59.94 from the D5
In FCP when I log a clip at:
01:20:00:00 in
01:20:30:00 out
After Batch Capture is complete the clip shows up in the browser as:
01:19:55:05 in
01:20:25:05 out
FCP is effectively changing the logged timecode of the clip. I'm capturing with burned in TC and the Burned in TC is Frame accurate, but why is FCP changing the clip's TC?
In all my experience with FCP I have never encountered this issue and I am completely puzzled. I've contacted AJA and they have said that they do not know of this issue and were puzzled also. I am using a Tri-Level Sync and everything seems to be getting proper reference.
There is no reason why FCP should be changing my logged clip settings. (right?) Also, I tried a test where I made the clip that came in with the bad timecode offline, and then ran a Batch Capture again, and it changes the logged timecode even further. I've tried a variety of Device Control settings playing with frame offset etc with all having the exact same numeric result (see TC above).
Anyone who has any insight or similar experience your thoughts are greatly appreciated. Thanks for the help
Ted - Editor, NYC

The BITC matches the original Logged TC (even though the logged TC changes after capture)
Logged TC (Media Start/End in FCP)
01:20:00:00, 01:20:30:00
Captured TC (Media Start/End in FCP)
01:19:25:05, 01:20:25:05
Burned in TC Captured (Viewable on Video File)
01:20:00:00, 01:20:00:00
I'm very curious about what yourlooking at on the deck manual. Page 145??? I don't see a page 145. It's been my understanding that the Monitor HD-SDI does produce the 720p 59.94 signal, and that's what all my monitors and Kona say that their getting.
Also, could you clarify your last sentence.
*"Forgive my guessing but this deck looks like it really wants to work in 1080 and 720 is kind of there to step up from 8 bit DVCPro HD."*
I dont think that its a 23.98 issue and our source tape is not 23.98, even still if it was, it shouldn't effect the logged TC.... but I'll try it in the morning, could'nt hurt.
Update: A person over the phone at Apple "didn't" (did) say over the phone that upgrading to 5.1 (universal) would improve 720p capabilities.
So the next step will be giving more money to Apple for Universal and installing the new Kona drivers released yesterday.....and then let the testing fun begin again.
Thanks so much for your help, please let me know where to find that info in the D5 (3700B) manual. Cheers.

Error while Batch Capturing on to Final Cut Pro

Hello,
When you batch capture from any deck randomlly it gives an error "do not attempt to eject the tape" and the capture stops and after that it gives this error serveral time again and again but the same tape works fine with other machine.
Try to help me out as soon as possible.
Thanks

Sounds like you need to repair the video playback machine which is sending the error messages...
Jerry

Batch Capture (Re-Capture) with Free Run TC

I'm batch capturing footage from 5 years ago for a client that wants another copy of their video. 1 tape was shot REC RUN timecode and it batch captured without issue. However, the 2nd tape is FREE RUN timecode and the capture utility bounces all over the place trying to find the in point. 50 clips, 0 successful captures.
Have adjusted handles, etc....no dice. I actually had re-captured this tape in CS4 a few years back and it worked fine, might have lost one clip total. Now in CS5, nada.
Let me know if anyone has an idea what I can do to make PPro park the playback right on the in point without trying to preroll, because nothing I've tried so far has worked.
For all I know it's a specific issue with CS5...dunno....I turned my back on MiniDV tape a while back and have not tried it since.
Using CS5, PC, Panasonic camcorder is the capture device.
Thanks!

Ann Bens wrote:
Why not capture the whole tape with scene detection.
Then chuck out the clips you do not want.
Ultimately this is what I intend to do if I can't find a resolution for this issue by the time I start working on the project again tomorrow. It should work, re-linking clips doesn't involve preroll or handles so I don't expect any problems going that route. I do expect to capture about twice as much footage as I actually need, as you indicated, so that will be a small hassle but that seems to be the workaround for the moment.
Thanks for the responses....if anyone else has something they'd like to add (or if anyone is aware of this kind of thing being a recognized bug) feel free to weigh in here. I might file a bug report...it seems to be that the preroll settings are not being recognized, or something along those lines.
Oh, I should also have noted that this is a fresh (er...4 week old) install of CS5 on a fresh (ahem...also 4 week old) install of Win7 x64. So there's not an application conflict...this is just an Adobe computer for all intents and purposes.

Batch Capture : Timecode Error?

So I am attempting to capture my first video onto FCP from my Canon XL. I have about 5 minutes of video and I have logged the info for each clip. They are all in my "Bin 1" and it is set as a "logging bin." The first logged clip that i want it to capture i have marked the "In Point" at 00:00:00;00 and the "Out Point" at around 00:01:09;24. The rest of my 11 clips just go in order (i.e. 2nd clip: In = 00:01:09;25 etc...). After doing all of this I click on "Batch" under the "Capture" option, a big black screen pops up over my FCP with the capture info underneath the black screen in a gray strip. My camera then rewinds to the beginning and STOPS. I then have to sit and wait for anythin to happen, my camera still saying "STOP," and then a message pops up reading the following:
Batch Capture: Timecode Error: Unable to locate the specified timecode. You may have specified a timecode with insufficient room for a pre/post roll operation.
I have no idea what this means and I am beginning to get impatient with capturing my video. In the Log and Capture window, the tab that says Logging, i did not mess with the "Markers." I don't know if this matters.
Any help would be GREATLY appreciated so that I can start editing my project with this wonderful software otherwise.
God bless,
|-(|:^D
`

In standard trim, FCP needs at least 5 seconds preroll before capturing. The preroll is so the tape can get up to speed, the heads read timecode accurately and so on. You have discovered what happens when you give it no oppertunity to sort itself out.
The simple answer for your current situation is to set your first in point 10 seconds after the start of the time code. Be sure to make sure your last clip's OUT point is 10 seconds or more before the end of time code or you can have problems at that end of the capture as well.
The long term answer is next time let the camera run for a minute or two before you start recording anything you will want to keep. The same is true for the end of the tape - let it run for another half minute or so.
Cheers,
x

Batch Capture Error: Timecode Error: End of Tape Reached

I have been having issues doing batch capture with my JVC VS30U. I logged all my clips on the fly and did the entire tape, so the OUT point of one clip is the same as the IN point of the next clip. When I attempt to batch capture it gives this error between every clip.
I have to hit retry, sometimes more than once, in order for the deck to properly cue and FCP to start the digitize. I don't know if this is a weird pre-roll issue, or something else, but it completely defeats the purpose of a batch if I have to sit here and hit retry after each clip.
There are no TC breaks, and obviously its not really the end of the tape. I've read where people have similar problems, but didn't find a solution. Have already trashed prefs, but to no avail. Using FCP 5.0.4 with OS 10.4.3 and said JVC deck via firewire.
Any ideas? Thanks in advance!

I don't know the deck but a simple test would be to move a couple of i/o points so they are not adjacent. Or test with a single, longer clip and break it up into subclips.
Tell us what you've tried so we don't waster your time and ours with fruitless suggestions.
Errors displayed by FCP are usually irrelevant and rarely helpful.
bogiesan

Help with Batch Capturing, Timecode Issues?

Hi Final Cut Pro Pro's. I've just come over from Avid.
I have a problem with capturing - I have a lot of tapes to capture and there is no way I will make deadline doing it by individual capture - I need to batch capture. My tape shows no timecode breaks and I have already spent hours logging all the various clips. It shows it has registered all of the media start/end timecodes, but when I click on batch capture, it says
BATCH CAPTURE: TIMECODE ERROR: UNABLE TO LOCATE THE SPECIFIED TIMECODE. YOU MAY HAVE SPECIFIED A TIMECODE WITH INSUFFICIENT ROOM FOR A PRE/POST ROLL OPERATION.
I don't understand as there is clearly a functioning timecode? This is going to break my balls if I have to go through this individually, no time! Anyone? Any ideas?
Thank you.

I'm capturing from the camera directly, a Sony DSR-250...
It turns out that yes, if you have marked the in/out point too close to the head or the tail of the tape, or even if you have marked it okay and are currently at the start/end of tape when pressing on batch capture it cannot send the command to the device. If you move forward or backward accordingly by five or six seconds it doesn't come up anymore.
Thanks for all the responses, I'm going to make deadline now. Apple forums are my hot hot S€X.

Batch Capture - Error/Warning

I have a PowerPC G5 with a Firewire800 external HD plus a SATA external RAID system all connected to the G5. I have been (up to now) successful in batch capturing my video's. I now get an error message (warning) when I attempt to batch capture even one file. The messages says:
Warning:
_You are about to capture non-drop frame media from a device currently detecting or configured for drop frame media. If you proceed, you may experience changes in logged in and out points, problems relinking media or removal of master clip relationships_.
If I continue, the process quickly gives me an error.
My playback unit is a Sony DSR-11. I am capturing it directly to the 800 Firewire external HD (granite digital). I have ran TechTool on the G5 without issues (I even re-seated all the PCI cards, memory boards prior to running TechTool). I have two aftermarket cards (SATA card for the LaCie and a Firewire card). The Granite Digital is plugged into the standard 800 Firewire port.
The only way I can capture a video is by NOT using Batch Capture but only by capturing the individual clip. For some reason that works but the Batch Capture does not. I use this system a LOT for video editing (I use FCP Pro 6.0.5).
I would appreciate any suggestions.

I didn't receive a reply to this but I believe I figured out what what "drop frame box" Irl is taking about.
The only Drop frame box I could think of is in User Preferences. I unchecked that and it didn't do anything. I captured one clip and the audio was out of sync.
Looking at the Batch Capture dialog closer I noticed an unchecked "Add Handles" with a timecode that includes the semicolon. I checked that and started the recapture. The Warning came up again but I went ahead and the audio was back in sync.
I have no clue as to why this setting is in the batch window as I only thought handles were for trimming. The manual skips over what it does. I'll reply again if I find anything else.
Dan

Failed Batch Capture - Broken Timecode

Hello,
I'm attempting to capture some old footage from a project I had done in Premiere about a year ago.
There is clip in particular I'm trying to capture where the timecode was broken - premiere attempts to capture the first 8 minutes of my clip and then stops and gives me an error stating that the timecode was broken.
Is there anyway to force premiere to capture this clip all the way through and ignore the broken timecode point?
It's not a big deal to capture the clip "manually" but the problem is that I had split up and edited this clip so much, I'd rather batch capture it so that it will automatically appear on my sequence and I won't have to re-edit the whole thing.
Thanks!
FOO

I also have a Canopus card (in a system with Premiere 6.5) and broken timecode ("timecode hell" as I call it) was really only an issue when the tape pre-rolled over the break point during batch capture.
Do you still have the old Canopus .avi? You could use their util for CDVC <-> DVSD conversions:
http://download.videohelp.com/download/Canopus_DV_File_Converter.exe

Errors Batch Captures!! Tips for setting up Batch list corre

I have set up a Batch List, and I keep getting an error after I have imported the Batch capture list, when I go to Batch Capture I keep getting an error about Timecode? I am also wondering when doing a Batch List is ok to begin with 00:00:00:00 timcode as a media begin? As batch capture truly saves a lot time, I sincerely appreciate your time in courtesy in replying to my post.
Sebastian

I avoid this problem by shooting the first 30 seconds of each tape to throw away. That way, my starting code for any new tape is always at least 00:00:30;00. I started doing this back with FCP 3 (and now have FCP 5). So, I don't know if this is still an issue with the newer version. I do know, however, that working with timecodes below 30 seconds was a pain. Before I learned this trick, I would be able batch capture all of my other clips. Then, the first clip on each tape I would use Capture Now (which seemed to be less finicky with the low time codes).
I hope this helps.

Batch capture a sequence - strange error

Hi I am trying to batch capture a sequence (1 hour long, captured on DV PAL), now I am trying to get it into the FCP in HDV. I copy the sequence make all clips offline, select batch capture and it asks for a tape. So far so good.
Always when I put a tape it will rewind the tape fully and then give a time code error...
Is the first time I do a batch in FCP. I think I select the correct audio/video setup, but always happens the same: rewind and error...
Can anyone help me?
Am I missing something?

FCP rewinds the tape because it loads the clips in ascending timecode order -not the order that they appear in your sequence. This saves wear and tear on the tape because FCP does not have to spool back and forth, it simply progesses up the tape grabbing the clips.
It might be that the first segment that FCP is trying to grab is too close to the beginning of your tape and there is not enough stable timecode at that point.
Try the following: reduce the amount of pre-roll time or shorten the length of any handles you may have assigned.
It is probably a good idea to reduce pre-roll time and/or handles just for this first clip, then do the rest with your normal settings.

Batch capture HDV error

I have FCP 5.14 and have just logged a bunch of HDV footage offline. I did this the normal way I would when capturing DV footage, marking the in and out point and then log the clip, standard stuff?
When I try to Batch capture the offline clips it captures only 1 frame from each clip, then the clip details are also effected, ie the Media start and media end of my clips changes from what they where into two new time codes 1 frame either side of the newly captured clip.
Is this a program error or am I just completely useless??? Can somebody help me please

Not sure if this is your exact problem, but I've had issues with Batch Capturing HDV in FCP 5.1.4 using both a Sony M15U and M25U.
The deck would seek to the appropriate place on the tape and then just jog back and forth looking for the right start point. It would do this about 3 times and then give up.
The solution for this was a DROP FRAME / NON-DROP FRAME setting in FCP. If you go to your A/V Settings and then to the Device Control Presets tab and edit your preset (If it's locked you can just make a copy of it and edit the copy - I am using the Sony HDV firewire preset). If you know what your footage was shot in (drop or non) make this setting adjustment. If you don't know, try both.
As soon as this not so little detail was checked everything batch captured without fail. Just make sure there aren't any timecode breaks on your tape.
Hope this helps.

Unable to locate timecode in batch capture

Hi there, I have been working on this problem for a while and would really appreciate some help.
I have a documentary project I have been working on for some time and have completed the EDL. I am now trying to batch capture the footage again in full res and am having problems with a couple of the tapes.
First the specs:
The video was shot on a Sony HDR-HC1 in HDV(1080) mode.
I am using this camera to capture the footage.
I am trying to recapture the footage in a sequence with the easy setting on HDV1080i50.
I had originally captured the footage in SD on an older version of final cut pro (I am now working with FCP6) and didn't realise that my 16:9 footage was actually all 4:3 letterboxed. To fix this problem I used the media manager to export and then in the new project batch capture all the footage again from the tape. The project uses 18 tapes, 16 of which were batch digitised with only minor troubleshooting required. However 2 of the tapes are proving to be very problematic. It seems that whatever clip I select on the tape it gives me a message saying "unable to locate timecode".
I have tried setting the tape to the exact location of the clip before selecting the batch capture, but the computer always seems to look for a spot which is 2-3 mins out of sync with the clip. For example, if the in point is 00:10:00:00 the computer will roll the tape to around the 00:12:00:00 mark and start jogging around there for about 30 seconds until eventually giving me the "unable to locate timecode" message. Looking in the information in the bins, the in and out points are accurate, its just that when I try to capture, the computer rolls the tape to the wrong position.
If anyone knows a workaround for this that will help me avoid having to edit the footage all over again I will be extremely grateful.
Thanks
Liam

HI I have the same problem, the capture window says: Waiting for time code, the device must set in vcr mode and then This operation could not be complete as there is no video, the F!#!%$$ problem is very illogical ,at this mooring I do batch capture without a problem but since the second tape this problem starting, I update to FCP 6.0.4 and,. @@#%#@%#$ the first tape capture but the second not capture and the problem starting againd, note that IMOVIE capture the tape and work very well, iI replace fire wire, camera VCR and , I trayu with Canon, Sony, JVC and the problem persist , I have quicktime 7.4.5, FCO 6.0.4, note that I have two Macs with the same problem in both macs IMOVIE work like a PRO edition Software but FCP is very bad, I have with this problem a long time, I formated Mac, reinstall FCS2 many timers and the problem persist. IS not a problem whit easy setup or wherever , I download the FireWire SDK from Apple and test all connection with the applications of sdk and in all case , the camera and the fire wire are OK, the problem is with quicktime and FCP, If any one is working OK with FCP and DV NTSC devices and JVC PRO HD devices, please tell us HOW DO. I'm working with FCP since 2000 and in this month FCP makes me very UNHAPPY.

Timecode error in batch capture

Similar Messages

Maybe you are looking for