/tmp/mili2d.log writes my tmp folder full which course an esxi outage

Hi Gent`s
I hope you could help me further or pointing into the right direction.
We had last week an ESXi Server outage which was produced as the /TMP folder was full.
I notice now that there is still writing an mili2d.log, which has filled the /TMP folder.
As far as I could find out this log file will be produced by our network cards.
My question is how could I stop writing the log file and how could I solve the error which are reported in the log file...see below.
Many thanks for your help.
Br
Jörg
Fri May 22 02:57:28 2015,14995682,   ERROR:could not open device node
Fri May 22 02:57:28 2015,14995682,   ERROR:ioctl_get_chipinfo: ioctl_get_chipinfo failed
Fri May 22 02:57:28 2015,14995682,   ERROR:enumerate_be_nics: ioctl_get_chipinfo failed with status = 1
Fri May 22 02:57:28 2015,14995682,   CRITICAL:NO BE CARD FOUND
Fri May 22 02:57:28 2015,15585519,   ERROR:could not open device node
Fri May 22 02:57:28 2015,15585519,   ERROR:ioctl_get_chipinfo: ioctl_get_chipinfo failed
Fri May 22 02:57:28 2015,15585519,   ERROR:enumerate_be_nics: ioctl_get_chipinfo failed with status = 1
Fri May 22 02:57:28 2015,15585519,   CRITICAL:NO BE CARD FOUND
Fri May 22 02:58:45 2015,15585762,   ERROR:could not open device node
Fri May 22 02:58:45 2015,15585762,   ERROR:ioctl_get_chipinfo: ioctl_get_chipinfo failed
Fri May 22 02:58:45 2015,15585762,   ERROR:enumerate_be_nics: ioctl_get_chipinfo failed with status = 1
Fri May 22 02:58:45 2015,15585762,   CRITICAL:NO BE CARD FOUND

Hi cykVM
It`s an Vsphere 55u2 2456374 Build.
Hmmm, maybe the bnx2i driver which could course writting to the log file?
~ # esxcfg-scsidevs -a
vmhba0  hpsa              link-n/a  sas.50014380264bfec0                    (0:2                                                                                               :0.0) Hewlett-Packard Company Smart Array P420i
vmhba1  ata_piix          link-n/a  sata.vmhba1                             (0:0                                                                                               :31.2) Intel Corporation Patsburg 4 port SATA IDE Controller
vmhba2  qlnativefc        link-up   fc.5001438024250029:5001438024250028    (0:3                                                                                               6:0.0) QLogic Corp ISP2532-based 8Gb Fibre Channel to PCI Express HBA
vmhba3  qlnativefc        link-n/a  fc.500143802425002b:500143802425002a    (0:3                                                                                               6:0.1) QLogic Corp ISP2532-based 8Gb Fibre Channel to PCI Express HBA
vmhba4  qlnativefc        link-up   fc.5001438024250009:5001438024250008    (0:3                                                                                               9:0.0) QLogic Corp ISP2532-based 8Gb Fibre Channel to PCI Express HBA
vmhba5  qlnativefc        link-n/a  fc.500143802425000b:500143802425000a    (0:3                                                                                               9:0.1) QLogic Corp ISP2532-based 8Gb Fibre Channel to PCI Express HBA
vmhba32 bnx2i             unbound   iscsi.vmhba32                           Broa                                                                                               dcom iSCSI Adapter
vmhba33 bnx2i             unbound   iscsi.vmhba33                           Broa                                                                                               dcom iSCSI Adapter
vmhba34 ata_piix          link-n/a  sata.vmhba34                            (0:0                                                                                               :31.2) Intel Corporation Patsburg 4 port SATA IDE Controller
~ #
There is no directory "ocmanager" to find in my entire system.
I guess as well to update first with latest HPP SPP, otherwise I will open an support case on Vmware.
Many thanks for your Support.
Br
Jörg

Similar Messages

  • Cluster with shared domain folder using OCFS2 and the domain /tmp folder

    I've setup a cluster with two machines and one managed server on each machine. One of the machines also hosts the admin server.
    Initially, both managed servers were running on the same machine. Everything worked well. When I move to having two machines, I didn't want to have to independently maintain the domain folder on each machine.
    So I decided to setup a shared drive between the machines and use OCFS2 to share the domain folder between the two machines.
    Everything started up fine, but when I deployed software to the server I would frequently (but not always) get this error:
    [wldeploy] Target state: deploy failed on Cluster cluster-01
    [wldeploy] weblogic.management.DeploymentException: [Deployer:149189]Attempt to operate 'deploy' on null BasicDeploymentMBean for deployment mylibrary#[email protected]. Operation can not be performed until server is restarted.
    After looking around a bit on google I saw this issue:
    http://download.oracle.com/docs/cd/E11035_01/wls100/issues/known_resolved.html#CR279281
    which says
    Some OS and NFS combinations result in deployment failures or configuration updates with an exception like:
    weblogic.management.DeploymentException: Attempt to operate 'distribute' on null BasicDeploymentMBean
    Workaround or Solution:
    * Run statd() and lockd() processes on every NFS client that accesses a remote NFS volume.
    * If multiple servers that share the same domain root are started with different user Ids of same group, set the correct "umask" for the server processes so that a file created by one server can be opened for read/write by other servers without security exceptions.
    Unfortunately, I wasn't running NFS, so the workaround didn't help me.
    Through dump luck, I tried this:
    I replaced the domainroot/tmp folder with a symbolic link to a folder on each machine's local filesystem. Following that change my deployments work everytime.
    Does anyone know why this change worked? What is the purpose of the /tmp folder in a domain folder?
    Are there any switches I could turn on to get more information about the exact error that causes the deployment mbean to come back null?

    It may not be the same situation, but I had this "deployer:149189" error and it turned out to be mixing WLS 10.0 and 10.3 installations together in the same install directory and not being scrupulous about environment setup. I think the problem was caused by accidentally running a 10.0 domain with Java 1.6.
    Eoin.

  • Xorg crashes when Thunar views /tmp folder

    After I upgraded to Xorg 1.16.0-6 yesterday and restarted, whenever I open Thunar and go to the /tmp folder, Xorg crashes and the system becomes completely unresponsive (for instance, the sound from banshee infinitely stutters on a single sample). I have to hard reboot the system to regain use. It doesn't appear to occur with any other folder, and removing the thumbnailer didn't help. Checking Xorg.0.log.old in /var/log shows it segfaults when this happens. I am using the Radeon open-source drivers with a Radeon HD 7310. (This occurs both with the standard Arch kernels as well as the -ck kernel I use most of the time).  Any suggestions?

    headkase wrote:
    GourdCaptain wrote:
    I am using tmpfs for /tmp. I went to check /run/user/1000 which is also mounted with tmpfs, went to /run... and that also crashed it. Unfortunatly, REISUB is less than of use on a computer without a SysRq key or equivelent.
    EDIT: /tmp is mounted tmpfs with nodev and nosuid. ls-ing it from a command prompt doesn't cause any issues.
    If your system doesn't have a SysReq key then you hold Alt + Print Screen for each of the letters of REISUB with about a second or two between each letter.
    Huh. I tried that after enabling it as specified both with and without Fn (it doesn't say Fn+PrtSc = SysRq, but no harm in trying) and it still didn't work.

  • File manager problem - weird .tmp folder - PLEASE ...

    Every time I try to copy any type of file to my PC using File Manager, the file will not transfer and instead it creates a .tmp folder with a file inside PhoneFiles.
    Has anyone also encountered this?

    Hi,
    This post was started in april. Did any one found the solution for this? PC suite just doesnt allow to copy files directly from the Nokia file manager to PC. It creates the .tmp folder, with a 'PhoneFiles' named file in it. I just upgraded to Nokia pc suite 6.83.14.1.
    Phone model: Nokia 6630
    Phone firmware: Never updated
    PC suite ver: 6.83.14.1
    OS ver: Win XP prof with SP2
    It will be very helpfull if somebody knows a solution for this.
    Thanks in advance.
    SSB

  • Tmp Folder in Weblogic 10.3

    Can anyone tell me what is the purpose of tmp folder inside the domain directory for Weblogic 10.3
    * domain_name/tmp ?
    what is its purpose?

    instead of import weblogic.security.SubjectUtils; use import weblogic.security.spi.WLSUser; and get the username as below
    Set users = subject.getPrincipals(WLSUser.class);
              Iterator iter = users.iterator();
              while (iter.hasNext()){
                   userName = ((WLSUser)iter.next()).getName();
                   System.out.println(userName);
    this returns you the username

  • How to disable application jar creation in tmp folder

    Hi
    I am deploying an application on clustered server.
    Everytime i deploy application a jar(for the application) is getting created in admin server's tmp folder in the folder WLTEMP_APP_DOWNLOADS/<application_name>/<application_name.jar>
    I am deploying application in exploded format and one of its functionality is to generate csv files.
    As Weblogic seems to be referring the application_name.jar I get a 404 error whenever csv files are accessed in UI.
    Could somebody please suggest the settings to disable the application jar creation.

    The issue was with weblogic caching.
    The server was creating a jar of the application in a tmp folder for every deployment .
    Due to this any new file generated within deployment path was not being identified.
    Disabling caching on admin server resolved the issue.

  • Program/T-Code to load files from local system to XI system's tmp folder

    Dear all,
    Do we have any program or transaction to load files from our local system to the usr/tmp folder of XI system.
    Please share the info, if anyone has already faced the similar requirement.
    regards,
    Younus

    1) goto SXDA_TOOLS Transaction code
    2) Provide the Following details
    Object Type : DXPROJECT
    Program Type: BAPI
    Program/Method: CREATE
    3) Click on Copy Button
    4) Select the Source as Presentation Server
    a) Select the File where you saved in your Local machine
    5) Select the Target as Application server
    a) Check the check box Remote Server
    b) Select the File type as Physical
    c) In File name give /usr/sap/SSD/DVEBMGS00/work\Your file name (This the Server path
    Where the file is going to save)
    6) Click on Continue
    Go to AL11 and check whether the File has been create in the following path /usr/sap/SSD/DVEBMGS00/work
    Provide this path in the Communication channel path when you select the Transport Protocol as NFS and you place the file in AL11 directory.

  • Tmp folder

    How do I find and view the contents of the tmp folder? I tried searching in Spotlight for tmp folder and nothing comes up. I realize this is probably a basic question, but I am a recent switcher.
    Thanks in advance...

    You can use Find File in the Finder's File menu to search for visibility is invisible items, and that might bring up /tmp/ folder contents,
    It won't. It is possible to search within the /tmp and other unix folders, but to do so, you need to have that folder specifically selected on the location bar of the ⌘ F window.
    To show the /tmp folder, you can use the Go>GoToFolder command on the Finder menubar.

  • Tmp folder taking up 9GB

    I have almost 9GB of in my tmp folder; it does not clear when restarting. Most of it is in very small files, but it's eating up valuable space on my computer.  How can I best/most safely clear it out?  Other threads say it updates automatically, but it's one of the largest folders on my laptop.

    Try a restart.

  • Private TMP folder is growing exponentially.

    Starts at 16kb and grows to 95GB in a matter of days, forcing me to go back to an older copy.  Always goes back to 16kb and then is at 95gb days later.  Disk Inventory X has isolated it to the tmp folder, I just don't know how to stop it from happening.
    Update > The folders are .vbfolder_xxxxxx and contain two files, Archive.pax and Archive.pax.gz
    The folder replicates over and over again, getting bigger almost every time, with the same two files in them.
    I've done Virus Scans with Virus Barrier.  Not ready to start with a clean install unless I have to.
    Any ideas??

    I'm unclear as to how that would help?  Do you believe that Virus Barrier is the culprit?  It was downloaded from the Mac App Store, so I'm not concerned with its authenticity?

  • Java creating random folders on /tmp folder on RHEL VMs running on VMWare

    Hi
    I have a java program running on virtual machines (RHEL5 & RHEL6) on a VMWare hypervisor. We are seeing random files / directories being created in /tmp folder on those virtual machines with the owner as the user under which the java program runs. What could be possible reasons for this behavior and how to troubleshoot it?
    Regards
    -- Babu

    Which Java? Oracle Java? OpenJDK? JRockit? Which version? How did you install it? Imagine someone coming up to you and saying "yeah, Linux isn't working, what could be the reason?" Oh, okay. That narrows it down.
    Not that you are going to get many answers in a user to user Java -programming- forum, your question is more suited for Redhat support or a Redhat tech forum.

  • [SOLVED] Home folder full & can't figure out why (MBs not matching up)

    /home (as a partition) is 5GB and completely full... however, XFE, emelfm2, and PCManFM all see the home "folder" as being between 1.3GB and 1.8GB full... I am under the impression that I have a ghost file SOMEWHERE that even root can't properly detect, as it's not making any sense.  What tools can I use to figure out why my /home partition is full?
    Note: XFE, when checking the properties of the home partition vs home folder, it also shows the partition as full and the contents of the folder as 1.5GB or so.  I can't shut down the computer, as I'm transferring large files from one flash drive to another (and my /tmp is on another partition and is 1% full out of 3.8GB. The comand 'df' returns that the partition is full as well... all tools, whether accessed via root or user, are telling me contradicting things: partition full, folder 40%(ish) and it's driving me mad!  Any and all help is, and will be, GREATLY appreciated!
    SOLUTION:
    installed ncdu from repos, used command 'ncdu /home' and found which folder was the culprit... I had a large transfer going overnight that wasn't going when I got back in the morning, so the disk wasn't at 100% when I got back (not sure why any space was taken up by the transfer since the tmp folder is NOT in /home and the transfer wasn't to or from /home, but that may be an issue for another day).
    Last edited by CPUnltd (2012-01-25 20:37:44)

    trash was empty, lost+found could be a possibility... what is ncdu?
    EDIT:
    figured out what ncdu is, can't believe I'd never seen this program before!!! will be using it to track down the issue tomorrow! THANKS!!!
    Last edited by CPUnltd (2012-01-25 08:58:32)

  • Apache Sling Logging Writer Configuration

    Hi,
    I'm having an issue where my custom log writer configuration is not being picked up and used by CQ5 sometimes.  I've created a custom error log writer based on the example provided at http://helpx.adobe.com/cq/kb/HowToRotateRequestAndAccessLog.html which I've installed on an author, replicated it to the publishers, and all seemed ok and working correctly.  The settings are:
    Log File: ../logs/error.log
    Number of Log Files: 5
    Log File Threshold: 200MB
    After installing this, the error logs rotated at 200MB resulting in error.log.0, error.log.1 etc as expected.
    However after rebuilds on the machines, this configuration was overwritten (as expected).  So I've installed and replicated the package again, but now the configuration is not taking effect.  I'm using the exact same config package as I was previously, but the logs don't seem to be rotating at all now (not even daily).  I've deleted the config from the Felix console on all authors and publishers, reinstalled on the authors, replicated to the publishers, then restarted the CQ5 service on all machines, but it's still not working.
    So I have a couple of questions about this:
    Is there somewhere else in CQ5 that might be overriding these log writer config settings?
    Is ../logs/error.log correct for the standard log file location?  A note in step 3 of Creating Your Own Loggers and Writers on http://dev.day.com/docs/en/cq/current/deploying/configure_logging.html states:
    Log writer paths are relative to the crx-quickstart/launchpad location.
    Therefore, a log file specified as logs/thelog.log writes to crx-quickstart/launchpad/logs/thelog.log.
    To write to the folder crx-quickstart/logs the path must be prefixed with ../ (as../logs/thelog.log).
    So a log file specified as ../logs/thelog.log writes to crx-quickstart/logs/thelog.log.
         The configs in the log rotation example also use ../logs.  However when looking at the default/standard logging writer config, it uses logs/error.log.  Which one is correct?
    Any help on what's going on here would be appreciated!!
    Thanks,
    K

    Hi,
    I am answering your last question and this one here only.
    1. Log configuration can be override at project via creating config and overriding factory "org.apache.sling.commons.log.LogManager.factory.config-<identifier>" and writer (if required) "org.apache.sling.commons.log.LogManager.factory.writer-<identifier>". So plz check if you have configure log at project level. Now if you are not able to see then plz recheck you log configuration in felix console http://localhost:4502/system/console/slinglog here you can see entire log configuration for CQ system.
    2. both will work but the location will change
         i. CQ 5.5 - log file located under "crx-quickstart" ../logs/<filename>.log will create under this
         ii. CQ 5.4 - logs creates under "crx-quickstart\logs" also under "crx-quickstart\launchpad\logs" so if you select ../logs/ it will go under "crx-quickstart\logs" only but you can change wherever you want to store. Again you can see this configuration info at http://localhost:4502/system/console/slinglog
    3. You can also customize you log via creating at project level and assigning the "identifire" (with all other configure parameters) for more information you can refer http://sling.apache.org/site/logging.html apart from earlier share links.
    I hope above will help you to proceed. Please let me know for more information.
    Thanks,
    Pawan

  • HT1549 How do I read write to an external drive?  I am under admin account and cannot read write to any folder on the external drive.

    I have a Mac Mini with Mavericks installed, as well as a PC running Windows 7.  I want to be able to read write from both computers to an external drive on the Mac.  I created 2 folders on the drive and named them Movies, and TV Shows.  The content of those folders are the respective files. I set up both folders to be shared on the Mac under system preferences, and then mapped the drives on the PC.  I also created a user account with admin privileges on the mac that matched my PC.   I then copied a Music folder to the root drive instead of using external, and set up sharing as well.  File Sharing is selected for all three folders, however the music folder is the only one which allows me to change the permissions to allow read write to everyone, or to create individual user accounts to connect with read write permissions.  The options to add users or change permissions are simply grayed out for the two folders on the external drive, so not only can I not write from my PC, but I can’t even do it on the Mac with the administrative user logged in. The folder on the root drive is fine but I cannot make any changes to the external drive at all.  Get info for any folder on drive shows read only.  SMB and AFP are selected for all folders under options.  I can access all three folders from PC, but can only add files to the Music folder. I cannot do anything from either computer to the folders on the external drive.

    Try Applications/Utilities/Disk Utility - select the drive and run Repair Disk.

  • Run with user privileges but write to restricted folder

    In Windows Server 2008 R2 (and in an Active Directory domain), the login and logoff scripts are run with user privileges.
    Suppose that I run script1.ps1, when user1 logs in; I need that script1.ps1 is associated to user1, because it will write some informations about that user: it modifies a log file in a folder. Anyway, script1.ps1 will be run with user1 privileges.
    I obviously made that file and that folder accessible (readable/writable) to user1: but I actually don't want the user to modify that log file. I would like that
    only the script could do it.
    Is there a way to work around this problem? Maybe should I run script1.ps1 in a different way?

    Henry.  You can add a subscription to a server that subscribes t event log entries on user computers.  Subscribe to the logon/logoff events. Now you have a central repository of logon and  logoff events.
    There is no way to accomplish what you are asking to do.  Any file that can be written to in logon script or during a user session can be changed by the user.
    Bil is suggesting a "startup" script that runs when the user logs on and not when the computer starts.  A user startup script runs as the user and not system.
    Another method is to schedule a script that run at logon.  This can run as system and write to a file that the user cannot change.
    ¯\_(ツ)_/¯

Maybe you are looking for

  • Theme / CSS question

    Hello! I have a very basic theme / csss question: Working with Oracle XE and Apex I want to create my own theme. Therefore I tried to use http://wiki.shellprompt.net/bin/view/Apex/ThemeTips But thereit says: 1. Copy the theme_4 images directory to th

  • Function in namespace not found

    I'm trying to move out small piece of code to just prepare and execute some xquery function. I do exactly the same thing as in main branch, but in moved out code I'm getting the error: (6, "Error: Function 'xxx' in namespace 'http://www.my.com' with

  • Dates shifting by a day in shared calendar

    Hello there, I have a shared calendar with my band where I'm the administrator. For some reason, everytime one of my friends input an event it shows in my calendar in the wrong date, more precisely it shift one day forward and displays always that th

  • Streams on a standby database

    Does anyone know if Streams can be implemented on a standby database (logical or physical stnadby)? In other words, can a standby database be the source or primary database for streams?

  • Do I get encryption with transport-guarantee set to NONE over HTTPS?

    Hello, If I established HTTPS connection and then access some web resource which either does not have <user-data-constraint> or has <transport-guarantee> set to NONE. Do I still have my communication encrypted? I read Servlet spec 2.3, but does not f