TMS configuration  for multi-clients in one system

Hi All,
we have got some problem defining transport routes in stms in transport domain...
We have to add to target group for one system 6 clients:3 clients with the dev/test roles for country X and 3 clients with dev/test roles for country Y.
Transport requests have to route only between clients for defined country (only for country X or only for country Y, must not mix).
How i can get status when transport requests will route in one system only between clients of country X (or only for country Y)?
Should i define two target groups and add to one group 3 clients for X and to the second 3 clinets for Y? I am not sure that it is enough. May be exists a lot of other options/ actions?
Where is garanthy that requets from country X will not mixed with requests from Y?
Thanks a lot.

> The SSO is working fine for only the client which we used to import the certificate (verify.der).
> 1>Is it that the certificate import should be done from all the clients exclusively ?
Logon ticket certificate is instance wide, not client dependent. And you need to call STRUSTSSO2 in client 000 to export/import.
> And the SSO is not working for other clients  in the same system .
> 2>If yes  can you tell the procedure, why b'coz transaction STRUSTSSO2 is same for all clients and if we try to import the certificate again how about the existing one over there ?
Could you provide more details about this issue you're facing? What is the Portal UME source? What application is it based on, BI or ESS/MSS?

Similar Messages

  • How to configure TMS landscape using three clients of same system?

    Hi All,
    I have to design a prototype for linking satellite systems to Solution Manager. To work on the Change Request Management module of Solution Manager.
    Here, I need a Development - Quality - Production landscape to be configured to link it to Solution Manager, but I have only one system available to do this.
    I have the clients 410, 420 and 430 in the system XYZ. Now, how do I simulate the three system landscape in STMS for the three clients mentioned above.
    I tried using many attempts, but it is not working out. I could figure it out that this is possible by activating "extended transport control" parameter for each system, in STMS.
    Also, there are some specific needs to configure this landscape for linking to Solution Manager, the comments are shown below:
    "Transports are supported in the standard transport layer of each client. When you configure transport routes, note that only consolidation routes that are assigned to the standard transport layer of the relevant exporting client are taken into consideration. For each exporting client, exactly one target client and one target group are permitted.
    We recommend that you assign exactly one development system to a production system, and that these two systems are connected by exactly one unique transport track.
    If a development system and a production system are connected by more than one transport track, this may lead to inconsistencies within the transport distribution.
    This type of transport configuration cannot be supported by Change Request Management, and may cause inconsistencies within the tools involved."
    Please suggest me, as how to proceed to configure STMS for the same.
    Thanks in advance.
    Anil Santhapuri
    Message was edited by: Anil Santhapuri

    Hi Anil,
    Can you please share how you could setup the 3 system landscape with diferent clients on one system using Target Groups?
    Thanks,
    Poorna

  • "This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible.  This host does not support Intel VT-x"

    Hi, I have installed vmware 5.5 hypervisor on hp G8 microserver. I have created one vm as windows 2008 R2. I have also install vmware workstation 11 on this vm. In this workstation when I tried to run vmware 5.5 hypervisor I come across "This virtual machine is configured for 64-bit guest operating systems. However, 64-bit operation is not possible.  This host does not support Intel VT-x" this statement. Which shows that the host machine does not support virtualization and for that you need to go in Bios and enable it but in present case as host machine is also a vm and you would not find much detail of Bios when you log into the Bios therefore, I am pretty much stuck here. I don't see any information in relation to this. Now my question is:
    1. Can we run ESXi inside a vm which is already sitting on ESXi?

    I moved the discussion from VMware Workstation to Nested Virtualization which contains several hints on what's possible and what needs to be configured to make things work.
    André

  • HR CEE add-ons for different countries in one system

    Hello,
    is it possible to have HR CEE add-ons for different countries in one system?
    Will SAP system work properly? What kind of risks of these imports?
    Thank you very much.

    A couple of generic answers on add-ons
    - of course you can have several add-ons working on the same B1. To understand
    the details on how add-ons are started and maintained by B1 desktop pls refer
    to the e-learning available here on SDN
    - compatibility of add-ons. There is no generic answer to this, it depends on the
    functionality and implementation of the two add-ons. Anyway, if two add-ons are
    functionally independent and they follow the solution guidelines, then they should
    be interoperable. You can find the solution certification guidelines here on SDN
    under the ICC section: these rules cover points like namespaces, event handling,
    user table and form creation and so on that enforce interoperability.

  • Apps for different clients with one creative cloud license

    Can I publish apps for different clients with one single edition license on creative cloud?

    Well, "should" is about as good as it gets, no one is going to enforce that, and it's certainly making me think very very hard about whether to bother with a pro licence again in August!
    And yes I'm very much aware of the few advantages of the Pro Licence, I do need to see some much bigger differentiators to justify the extra cost though!
    Just putting cards on the table :-)
    Alistair

  • TMS configuration - Transports between clients

    Hi Experts,
    I have an ECC system on which I would like to configure 3 clients.  Client 400 for DEV, client 500 for QA, and client 600 for PRD.
    I would like to configure TMS so that I will be able to transport directly from 400 to 500 and from 500 to 600.
    Could anyone tell me if this is possible and (if so) how it should be done?  Could you take me through the process?
    Many thanks,
    Aldo

    Aldo
    If you drill down further in the above link, you may find what you are looking for:
    http://help.sap.com/erp2005_ehp_03/helpdata/EN/44/b4a09a7acc11d1899e0000e829fbbd/frameset.htm
    title
    u2022     Improved import controls
    If you work with extended transport control, you can import requests into different clients in a system without using  unconditional modes.
    When you first import a request into a system, all the objects are imported completely. Any subsequent imports into other clients in the system only import client-specific components.
    This makes it possible to set up consolidation routes and delivery routes between different clients in the same system.
    Hope this helps!
    PJ

  • SCM and CRM Multiple Clients in one system

    Dear all,
    I want to ask a question regarding Multiple clients in SCM 5 - IDES and CRM 5 -IDES.
    I installed the system and plan to have multiple clients in a system with copying client 800 (IDES) to others.
    I heard opinion that it can't possibly be done because if during the exercise the Administrator Workbench is executed it will search to the source client (800) and probably affect the exercise.
    Would you mind giving me more suggestion about this?
    Thank you.
    Fausto

    Hi Fausto,
    Could you be more specific about what you need to achive?
    You can always creat a new client, logon to the client and do a client copy with TCod SCCL.
    If you logon to other IDES clients then You'ld overwrite the content of the client which have been pre-configured.
    Check the status of the client you need to overwrite from TCod scc4.
    Also to verfiy the status of the target client for TCod se06 -system change option.
    Regards,
    Tolulope

  • Solman_setup configuration for local client copy

    Dear Experts,
    We made a client copy from 100 to 110 in solution manager 7.1,But solman_setup configuration is missing. how we can copy the java solman_setup configuration also?

    Hi Prathish,
    always welcome.... but I hope you have understood now that solman doesn't support multi client concept.
    There is nothing wrong technically to create a new client but you need to know which functionalities/module within solman support client dependent or client independent configuration
    for e.g Monitoring Template are not client specific ..check below FAQ link
    Monitoring and Alerting related FAQ - Technical Operations - SCN Wiki
    hope this helps your understanding further...
    Thanks
    Prakhar

  • Backend configuration for Fiori client

    Hi experts,
    we would like to try out the Fiori client for Android (Link: SAP Fiori Client - Android Apps on Google Play), but I don't know which URL has to be entered in the client.
    SAP fiori is accessable on our SAP Server in web browser via URL https://server:port/sap/bc/ui5_ui5/ui2/ushell/shells/abap/FioriLaunchpad.html, but when I try to use that URL within Fiori client I get a 404 error. The same goes when just I use https://server:port.
    Which URL does the Fiori client expect for connection to SAP backend? Or does this indicate that the backend isn't fully configured for connection from SAP Fiori client?
    Thanks for your help!
    Best regards
    Alej
    Tags edited by: Michael Appleby

    Hello Krishna,
    Thanks a lot for your very fast response!
    You were correct... I am ashamed to tell you that it was a network issue.....
    Unfortunately I have a follow-up issue. Instead of the new fancy login page I get only get an old-fashioned one when starting the LaunchPad URL (the one also mentioned in my first post):
    When starting the fiori admin panel via URL https://server:port/sap/bc/ui5_ui5/sap/arsrvc_upb_admn/main.html the new login page is properly displayed:
    Any idea what is causing this? It puzzles me since both URLs should use the same HTTP handler from ICF node /default_host/sap/bc/ui5_ui5?
    Kind regards
    Alej

  • Transaction Launcher for Multi Client system

    Hi Gurus,
    I need a very big help. This is my problem:
    The CRM system on which I'm currently working has two client 1 and 2 and the second one
    is closed to customizing, so that all the settings we can make are on
    1. When we create a transaction laucher object, by
    transaction CRMC_UI_ACTIONWZ, we got the following error: "An RFC
    destination could not be specified for the logical system 2" (even if the connection are all set up)
    and if we set it from 2 at the end of the process we get the
    following message: "Client 2 has status not modifiable".
    In this way both on client 1 and 2 we´re able to execute only
    transactions of client 1.
    All the settings have been done according to the official SAP guide.
    Since on SAP guides there are no information about how set up the
    transaction laucher in a similar situation, how can we solve this issue?
    Please, reply as soon as possible.
    Thanks a lot,
    A.G.

    Hi Helmut,
    well I am also not sure what they did, but anyway, from the beginning on bw is designed to have only one client to work in. Technically I believe that all of the 'BW-Tables' storing the BW metadata don't have a client field. So how will you separate developments of different clients?
    regards
    Siggi

  • OCSM FOR MULTI CLIENT INSTALL

    Can anyone give me a clue as to why the Oracle Client Configuration Manager and the Oracle Client Software Agent do not appear as installable programs when you run Installer from the CD (and the Installer patch come to that)?
    Thanks.

    Hi SYDZ!!,
    You can install and activate Creative Cloud desktop applications on two computers, regardless of operating system, for the individual associated with the Creative Cloud membership. See the product license agreements page for more information.
    Link: http://www.adobe.com/in/products/creativecloud/faq.html#what-cc
    Regards,
    Romit Sinha

  • Disk and tempdb configuration for multiple Instances in one SQL cluster

    Hi Everyone ,
      I am in planing to build SQL Cluster on Blade server . Two blades are allocated for SQL. and planning to cluster those two blades. It will be windows 2012R2 and SQL 2012/2014. Initially it was plan to put most of database on one SQL instance. but
    due to other requirements I will be Installing more SQL Instance on same cluster. 
    for now Everything will be on  RAID 10 but do not have more details about storage yet that how it will get configured
    256 GB Ram on Each blade server.
    1) what are the Disc configuration recommendation for data and log files when each instance get added?
    2) what are the Disc configuration recommendation for  tempdb files when each instance get added?
    3) Each Instance Tempdb file on Same drive is good practice?
    Any other Best practices should follow for this setup?
    Thank you ....
    Please Mark As Answer if it is helpful. \\Aim To Inspire Rather to Teach A.Shah

    1) what are the Disc configuration recommendation for data and log files when each instance get added?
    Keep both the sql instances in diffèrent drives.read the below link for RAID levels and according to your usage you can cofigure it..
    http://technet.microsoft.com/en-us/library/ms190764%28v=sql.105%29.aspx
    Storage best practice.
    http://technet.microsoft.com/en-us/library/cc966534.aspx
    2) what are the Disc configuration recommendation for  tempdb files when each instance get added?
    Its good to have sepreate drive for tempdb and each instance too with correct allocation or configuration..RAID5
    for data if you must, but have to keep a spare drive around for that.
    Best is 10 everywhere. If that's too expensive, then 1 or 10 for log and 5 for data (and 10 for TempDB)
    RAID 5 is terrible for logs because it has a high write overhead. Tran logs are write-heavy, not read-heavy.
    3) Each Instance Tempdb file on Same drive is good practice?
    Tempdb configuration is depends, its completelty based on your server and tempdb usage..Make sure to have equal size for all the files in tempdb, As a general rule, if the number of logical processors is less than 8, use the same number of data files
    as logical processors. If the number of logical processors is greater than 8, use 8 data files and then if contention continues, increase the number of data files by multiples of 4 (up to the number of logical processors) until the contention is reduced to
    acceptable levels or make changes to the workload/code.
    http://www.confio.com/logicalread/sql-server-tempdb-best-practices-initial-sizing-w01/#.U7SStvFBr2k
    http://msdn.microsoft.com/en-us/library/ms175527(v=sql.105).aspx
    http://www.sqlskills.com/BLOGS/PAUL/post/A-SQL-Server-DBA-myth-a-day-(1230)-tempdb-should-always-have-one-data-file-per-processor-core.aspx
    Raju Rasagounder Sr MSSQL DBA

  • Server sizing for multi-client Acrobat Reader access of .pdf files

    I am trying to specify the appropriate file server (need processor rating & memory size)running Windows 2008 for 64 high tempo users on a LAN accessing large .pdf files (~20 mb each) using Acrobat Reader 8 or 9. Total data package size is about 30 Gig. LAN is Gigabit speed on CAT 6 cable.
    Suggestions?

    Time is 10:35 PM, Jan 30, 2014 after a day of nerve racking attempts to get Adobe Reader 11.0.6 to open a pdf file I have finally succeeded in doing so.  The following apkhan response to my original inquiry, even though it didn't directly help me much, but it gave me an insight that what I was inquiring about in the description of my problem had to do something with the EULA I was inquiring about and couldn't find were and how that is to be done.  For whatever reason I had installed Reader 11.0.6 three times throughout the day and still couldn't read a pdf file or see the EULA to agree to it or not.  During another installation of Reader 11.0.6 at 9:00PM, 1-30-14, a window appeared and required my administrative password to install the software and rightly so.  This is probably the reason why Reader was  so dysfunctional, because for whatever reason, this approval window didn't appear during the initial installations but I was allowed to install Reader anyways and the proof of it was it did end up in my Applications Folder-confusing and strange at best.  Without my administrative password the software should not have been allowed to be installed and this has always been the case. I will have to dwell upon that one for a while.  Anyway, for everyones information, the Mac version of 11.0.6 Adobe Reader doesn't ask for you to click a button to Agree or Not Agree to an EULA verbiage statement.  Just above the INSTALL BUTTON (Yellow Background)  on the installation window the instructions notes, when you hit the install button you aromatically agree to the EULA and the way you go.  I tried getting into the EULA via the Adobe the desktop Icon but to no avail.  Hopes this helps someone else.  Thanks to those at the Adobe Community that tried to help me with this mind boggling episode.

  • Chat Programm for multi client-server on LAN

    import java.net.*;
    import java.io.*;
    public class ChatClientThread extends Thread
    {  private Socket           socket   = null;
    private ChatClient client = null;
    private DataInputStream streamIn = null;
    public ChatClientThread(ChatClient client, Socket socket)
    client = _client;
    socket = _socket;
    open();
    start();
    public void open()
    try
    streamIn = new DataInputStream(socket.getInputStream());
    catch(IOException ioe)
    System.out.println("Error getting input stream: " + ioe);
    client.stop();
    public void close()
    try
    if (streamIn != null) streamIn.close();
    catch(IOException ioe)
    System.out.println("Error closing input stream: " + ioe);
    public void run()
    while (true)
    try
    client.handle(streamIn.readUTF());
    catch(IOException ioe)
    System.out.println("Listening error: " + ioe.getMessage());
    client.stop();
    public static void main(String args[])
    }

    Refer to the response here:
    http://forums.sun.com/thread.jspa?threadID=5428090

  • IT 0102 Grievances Configuration For Indian client

    Dear Experts,
    Please explain the IT0102 Grievances configuration and also explain for Portal configuration i.e, how to reflated IT0102 information and process over view.
    Thanks
    Sayini.S

    Hi Promod,
    Thank you for giving replay back,i am unable to understand this infotype process i thought that this process same as like US garnishment is it correct or any other process is there??? and can you explore the why we are using TI0102 and process please help me for this.
    Thanks
    Sayini.S

Maybe you are looking for