To be unable to discover a Nexus 5548 wirth DCNM 5.2(2e)

Hello,
I am unable to discover 2 Nexus 5548 with the SAN client of DCNM 5.2(2e)
These Nexus are used like LAN and SAN switch. Each Nexus is a SAN fabric. I would want to use DCNM in order to configurate the zone/zoneset via GUI. These Nexus 5548 run 5.1(3)N2(1b) release.
The Nexus ARE NOT managed via the Mgmt interface (OOB) but they are managed via an interface vlan (InB)
I could not configure rightly
- the snmp-server user (SNMP user V1/v2 or V3 + group ? ) CLI on Nx
- to configure the discovery in order that DCNM discover each fabric either from web GU interface or java SAN client
Please help !

I believe DCNM requires an ssh login to the Nexus and not SNMP.
DCNM uses Netconf over SSH protocol. See this earlier posting.

Similar Messages

E72 unable to discover BH-216 headset?

Greetings!
I have just bought a Nokia E72 to replace my old Nokia 6120c. Now, the 6120c was a great phone, but lacking a full keyboard as well as WLAN and GPS made me go for the E72.
Now, I have a strange problem: The E72 is unable to discover my BH-216 BT headset, that was previously paired to the 6120c, and works perfectly with the old phone.
The E72 however is unable to even detect the BH-216, and I do not know why? I already deleted the pairing on my 6120c, but I don't think this has any effect? Do I need to do anything special to get this to work?
I'm puzzled by this problem...
Thanks!

Dammit.
Next time I should really read the freaking manual...
Obviously, the BH-216 stores its pariring. Switch BH-216 off, then back on (hold on/off button for 6 seconds until green LED starts to flash rapidly) => Device open for discovery and new pairing.
Haha.
My fault.

FCoE with Cisco Nexus 5548 switches and VMware ESXi 4.1

Can someone share with me what needs to be setup on the Cisco Nexus side to work with VMware in the following scenario?
Two servers with two cards dual port FCoE cards with two ports connected to two Nexus 5548 switches that are clusterd together. We want to team the ports together on the VMware side using IP Hash so what should be done on the cisco side for this to work?
Thanks...

Andres,
The Cisco Road Map for the 5010 and 5020 doesn't include extending the current total (12) FEX capabities. The 5548 and 5596 will support more (16) per 55xxk, and with the 7K will support upto 32 FEX's.
Documentation has been spotty on this subject, because the term 5k indicates that all 5000 series switches will support extended FEX's which is not the case only the 55xx will support more than 12 FEX. Maybe in the future the terminology for the 5k series should be term 5000 series and 5500 series Nexus, there are several differences and advancements between the two series.

Prime Infrastructure 2.0 and Nexus 5548, SSH credentials fail

Hi,
I'm having problem getting the Prime Infrastructure 2.0 to login with SSH to a Nexus 5548 to do an inventory. I get "Wrong Telnet/SSH credentials". But when I use the same credentials from another SSH-client it works fine. I also tested to SSH from the console of the Prime-server and that also works fine.
Any ideas???
Regards,
Stefan Lindkvist

I have PI 2.0 working against Nexus 5k's in two different installations. See below for an example (click to enlarge).
Have you put in an entry in both the login and enable fields (even though they are not separately required when logging in directly)?

Telephony Issues on Nexus 5548

Dear Viewers,
I have Nexus 5548 devices in one of my client data centers and i have one 3750 switch to which all of these Avaya voice servers connect.
The 3750 switch was initially connected through a L2 Link to a 6509 catalyst switch and the telephony applications were working correctly.
The problem arises when i move this 3750 layer 2 link to a Nexus 5548 (OS version 5.1(3)N1 switch. All telephony calls coming from the outside (External calls) are not working as required but the internal calls work as usual.
What is odd is that when i migrate this L2 link back to the 6509 switch, all works as usual. This is just a layer 2 connection and i am wondering why this is not possible.
The vlan is accepted on all relevant trunks. I also deactivated igmp snooping on this voice vlan on the Nexus 5548 thinking it would help but in vain.
Any ideas and suggestions are welcome.
regards.
Alain

This is my radius config...... on a 5K
radius-server timeout 7
radius-server host 10.28.42.20 key 7 "Password" auth-port 1645 acct-port 1646 authentication accounting
radius-server host 10.28.42.21 key 7 "Password" auth-port 1645 acct-port 1646 authentication accounting
aaa group server radius Radius-Servers
server 10.28.42.20
server 10.28.42.21
aaa authentication login default group Radius-Servers
ip radius source-interface Vlan1
aaa authentication login default fallback error local
And it is currently working. On the radius server i also had to do this to make the users admins once logged in:
https://supportforums.cisco.com/document/137181/nexus-integration-admin-access-free-radius

OEM 12c unable ot discover Weblogic 10.0.1.0

I have OEM 12c grid installed and Agent 12c running on the remote host. I have weblogic 10.0.1.0 installed in the remote host. The agent is unable to discover the domain. It is failing with below error...
"Failed to discover WebLogic. Check host,port,credentials,protocol and be sure the server is running and the same farm is not already added. This UI can not be used to discover WebLogic version 7.x to 8.x. Exception: No targets discovered"
I can login to the console appication with the ip:port and credentials.. but failing while trying to discover thru the Grid Control.
I get below error in the OMS log...
2012-06-25T05:52:09.376-04:00] [EMGC_OMS1] [ERROR:32] [] [oracle.sysman.emas.model.discovery.AddWLStep1Model] [tid: Thread-38498] [userId: SYSMAN] [ecid: 0000DUEGUt_ADSqlcKU4V_0005hD0004kK,1:32596] [APP: emgc] [URI: /em/faces/as/discovery/addWeblogicStep1] Disocvery failed[[
java.lang.Exception: No targets discovered.
at oracle.sysman.emInternalSDK.sdkas.general.pojo.model.discovery.FMWDiscoveryBase.discoverTargets(FMWDiscoveryBase.java:588)
at oracle.sysman.emas.model.discovery.AddWLStep2Model.discoverTargets(AddWLStep2Model.java:1101)
at oracle.sysman.emas.model.discovery.AddWLStep1Model.discover(AddWLStep1Model.java:464)
at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at oracle.sysman.emInternalSDK.sdkas.general.pojo.progress.WorkWrapper.run(WorkWrapper.java:113)
at java.lang.Thread.run(Thread.java:662)
I then created a empty doman on the same remote host for the same weblogic version. I was able to attch this one and not the other domain.
I am ruling out OM Grid Server - Agent connectivity issues, since the new empty domain I created can communicate to server.
I tried to check what is different between domains...
The WLD that has the issue is a clustered Domain , and has:
- 9 Managed Servers
- Not SSL enabled
- Many Application deployed
- JDBC connections
- has a custom build authentication provider for Authentication. But i made sure the user id is valid and even can login to the console.
** The new Domain is an empty one - no applications deployed.
Can you please help understand why I am not able to attach the domain?

Hi,
It is the problem in prasing the DTD of config.xml file
It look like this
<?xml version='1.0' encoding='UTF-8'?>
<domain xmlns="http://www.bea.com/ns/weblogic/920/domain" xmlns:sec="http://www.bea.com/ns/weblogic/90/security" xmlns:xsi="http://www.w3.org/2001/XMLSchema-
instance" xmlns:wls="http://www.bea.com/ns/weblogic/90/security/wls" xsi:schemaLocation="http://www.bea.com/ns/weblogic/90/security/xacml http://www.bea.com/
ns/weblogic/90/security/xacml.xsd http://www.bea.com/ns/weblogic/90/security http://www.bea.com/ns/weblogic/90/security.xsd http://www.bea.com/ns/weblogic/92
0/domain http://www.bea.com/ns/weblogic/920/domain.xsd http://www.bea.com/ns/weblogic/90/security/wls http://www.bea.com/ns/weblogic/90/security/wls.xsd">
Please change your DTD to this lines and start the server.
Regards
Ravi D

Fabric with two Nexus-5548 and a brocade switch does not get fabric updates

We have a fabric containing two Nexus 5548 and a Brocade 5000 switch in interop mode 2. When i make changes to the zoning, the first nexus (the fabric principal) and the brocade switch see the zone changes. The second Nexus switch does not see it. There are no error messages but the change just can't be seen. What can i do to find out, what goes wrong ?

Ouch, deprecated is not the word i wanted to read
We are using 5.1(3)N1(1a) on nexus-rz1-a
and 6.0(2)N1(2) on nexus-rz2-a.
The fabric can be seen :
nexus-rz2-a# show fcs ie vsan 10
IE List for VSAN: 10
IE-WWN                   IE     Mgmt-Id Mgmt-Addr (Switch-name)
10:00:00:05:1e:90:57:27 S(Rem) 0xfffc01 10.88.133.110 (bc-san1)
20:0a:00:2a:6a:72:ba:01 S(Loc) 0xfffc1c 10.88.133.105 (nexus-rz2-a)
20:0a:54:7f:ee:7f:dc:01 S(Adj) 0xfffc0b 10.88.133.100 (nexus-rz1-a)
[Total 3 IEs in Fabric]
nexus-rz1-a# show fcs ie vsan 10
IE List for VSAN: 10
IE-WWN                   IE     Mgmt-Id Mgmt-Addr (Switch-name)
10:00:00:05:1e:90:57:27 S(Adj) 0xfffc01 10.88.133.110 (bc-san1)
20:0a:00:2a:6a:72:ba:01 S(Adj) 0xfffc1c 10.88.133.105 (nexus-rz2-a)
20:0a:54:7f:ee:7f:dc:01 S(Loc) 0xfffc0b 10.88.133.100 (nexus-rz1-a)
[Total 3 IEs in Fabric]
I try to distribute the zoneset this way:
zoneset distribute vsan 10
Zoneset distribution initiated. check zone status
nexus-rz1-a# show zone status
VSAN: 10 default-zone: deny distribute: full Interop: 2
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 6291 bytes
    Zonesets:1 Zones:62 Aliases: 44
Active Zoning Database :
    DB size: 10243 bytes
    Name: FABRIC1 Zonesets:1 Zones:60
Status: Zoneset distribution completed at 08:06:00 UTC Dec 3 2013
nexus-rz2-a# show zone status
VSAN: 1 default-zone: deny distribute: active only Interop: default
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 4 bytes
    Zonesets:0 Zones:0 Aliases: 0
Active Zoning Database :
    Database Not Available
Status:
VSAN: 10 default-zone: deny distribute: full Interop: 2
    mode: basic merge-control: allow
    session: none
    hard-zoning: enabled broadcast: disabled
Default zone:
    qos: none broadcast: disabled ronly: unsupported
Full Zoning Database :
    DB size: 6291 bytes
    Zonesets:1 Zones:62 Aliases: 44
Active Zoning Database :
    DB size: 10243 bytes
    Name: FABRIC1 Zonesets:1 Zones:60
Status: Activation completed at 13:03:42 UTC Dec 2 2013

CRS-10010: unable to discover DHCP server

Hy
I try to set up Grid Infrastructure using GNS. When running the root script
I get a Problem with dhcp.
Here an example of my problem:
[root@oranode1 bin]#
[root@oranode1 bin]# ./crsctl get clientid dhcp -cluname grid112 -viptype HOSTVIP -n oranode1
CRS-10007: grid112-oranode1-vip
[root@oranode1 bin]#
[root@oranode1 bin]# ./crsctl discover dhcp -clientid grid112-oranode1-vip
CRS-10010: unable to discover DHCP server in the network listening on port 67 for client ID grid112-oranode1-vip
CRS-4000: Command discover failed, or completed with errors.
[root@oranode1 bin]#
The dhcp server is tested by my admin.
Any Idea how to debug this problem ?
Thanks
Peter

Thanks , but this does not work
[root@oranode1 ~]# /u01/install/11.2.0.2/grid/runcluvfy.sh comp dhcp -clustername grid112
You must NOT be logged in as root (uid=0) when running /u01/install/11.2.0.2/grid/runcluvfy.sh.
[root@oranode1 ~]# su - grid
[grid@oranode1 ~]$ /u01/install/11.2.0.2/grid/runcluvfy.sh comp dhcp -clustername grid112
Verifying DHCP Check
PRVF-0055 : User "grid" does not have sufficient authorization to run this command
Verification of DHCP Check was unsuccessful on all the specified nodes.
[grid@oranode1 ~]$
do you know why?
Thanks
Peter

Install pbr feature nexus 5548

I am in need of Policy Based Routing for a new project. At my core I have a couple of Nexus 5548s clustered together. I go into configure terminal and run the command "feature pbr" and the return is invalid. So I check the license with the command "show license usage" and I get the following output:
Feature Ins Lic Status Expiry Date Comments
Count
FCOE_NPV_PKG No - Unused -
FM_SERVER_PKG No - Unused -
ENTERPRISE_PKG Yes - Unused Never -
FC_FEATURES_PKG Yes - Unused Never -
VMFEX_FEATURE_PKG No - Unused -
ENHANCED_LAYER2_PKG No - Unused -
LAN_BASE_SERVICES_PKG Yes - In use Never -
LAN_ENTERPRISE_SERVICES_PKG Yes - Unused Never -
From here I see that the enterprise package is installed and is unused. How can I gain access to the enterprise features? I found a document here that says "Ensure that you are in the correct VDC (or use the switchto vdc command). " The switchto vdc command is also invalid. What am I missing?
Eric

I realise this is a very old post however I wanted to post here in case others are still looking for this feature. PBR is now supported in version 6.0(2)N2(1) on Nexus 5k.
RELEASE NOTES: http://www.cisco.com/c/en/us/td/docs/switches/datacenter/nexus5500/sw/release/notes/6_02/Nexus5500_Release_Notes_6_02.html#pgfId-472355

IPhone 5 is unable to discover bluetooth enabled devices Mac Book and iPad

My new iPhone 5 is unable to discover bluetooth enabled Macbook and iPad sitiing next to it

That's not a feature of the iPhone. The only thing you can use bluetooth for with a computer is tethering.

Unable to discover Why No Join Predicate

Please help me, I have this query:
select pc.Val,
PC2.Valstring as valstring,
pc.ValString as MessageType,
pc2.Val as Port
from dbo.tblproperty p with(nolock)
inner join dbo.tblpropertycfg pc with(nolock) ON p.pkPropertyID = pc.fkPropertyID
inner join dbo.tblpropertycfg pc2 with(nolock) ON p.pkPropertyID = pc2.fkPropertyID
where p.pkPropertyID = 5
and pc.Concept = 'PBX'
and pc2.Concept = 'PBXIP'
I am attaching the Excution Plan, this plan showing "No Join Predicate" Warning, I am unable to discover where is the problem, please help.

Hi SathyanarrayananS:
Thank you for your support, when you say "are there any chance they are UDF or View" you mean if I could create and UDF or View with those tables?, because both tables are physical.
I am already readed the link and IMHO my query does not meets on any of examples provided.
As you can see, the first joins using the table, does not cause NJP, but when we apply the third join is when the NJP arise.
Do you need additional information about my schema?
Best regards.

Command to see transmit qeueing drops in Nexus 5548

Hello, 10g links in our core are getting rather congested as seen by MRTG graphs. Any command on Nexus 5548 to show transmit queuing drops on a given interface?

You could use #show queing interface eth 1/1
it shows you output similar as below:
NEXUS-1# show queuing interface ethernet 1/1
Ethernet1/1 queuing information:
TX Queuing
    qos-group sched-type oper-bandwidth
        0       WRR            100
RX Queuing
    qos-group 0
    q-size: 470080, HW MTU: 9216 (9216 configured)
    drop-type: drop, xon: 0, xoff: 470080
    Statistics:
        Pkts received over the port             : 222434
        Ucast pkts sent to the cross-bar        : 199674
        Mcast pkts sent to the cross-bar        : 22760
        Ucast pkts received from the cross-bar : 101087
        Pkts sent to the port                   : 145083
        Pkts discarded on ingress               : 0
        Per-priority-pause status               : Rx (Active), Tx (Inactive)
Total Multicast crossbar statistics:
    Mcast pkts received from the cross-bar      : 43996

TACACS Nexus 5548 Authorization

I am having an issue with authorization on the Nexus 5548. Note: The tacacs configuration has and still works correctly with all non-Nexus gear.
Authentication succeeds, and initiatial authorization passes. However, all sh and config commands fail, though AAA Autho Config-Commands .... and Commands Default Group <Grp Name), are configured.
ACS generates the following error: 13025 Command failed to match a Permit rule. The Selected Command Set is DenyAllCommands. I created an AllowAll, but am unclear how to associate this with Access Policy.
Any help would be greatly appreciated.

Hello,
Hope the attached document points you into the right direction.
Regards.

Unable to discover local disks in T5220

According to http://docs.oracle.com/cd/E35328_01/E35332/html/vmusg-storage-types.html#vmusg-storage-local
I should be able to use extra disks in a T5220 to store VMs:
Local storage consists of hard disks installed locally in your Oracle VM Server. In a default installation, Oracle VM Server will only use the first disk (/dev/sda), leaving other disks available for storage.
As long as no partition and data are present the device will be detected as a raw disk. The choice is yours to use the local disks either to provision logical storage volumes as disks for virtual machines or to install a storage repository. If you place a storage repository on the local disk, an OCFS2 file system is installed.
But I am unable to discover these disks using Oracle VM Manager 3.2.2.520, managing a host running Solaris 11.1 with latest version of VM Server for SPARC:
# pkg list | grep ldom
consolidation/ldoms/ldoms-incorporation     0.5.11-0.175.1.9.0.4.0   i--
system/ldoms    0.5.11-0.175.1.9.0.2.2    i--
system/ldoms/ldomsmanager    3.0.0.4-0.175.1.9.0.4.0    i--
I suspect that it is because "partition and data are present" on the disk, but I don't know how to delete partitions with the format command, only change them to unassigned and zero length, and that didn't work:
partition> p
Current partition table (original):
Total disk cylinders available: 46873 + 2 (reserved cylinders)
Part      Tag    Flag     Cylinders         Size            Blocks
0 unassigned    wm       0                0         (0/0/0)             0
1 unassigned    wm       0                0         (0/0/0)             0
2     backup    wu       0 - 46872      279.38GB    (46873/0/0) 585912500
3 unassigned    wm       0                0         (0/0/0)             0
4 unassigned    wm       0                0         (0/0/0)             0
5 unassigned    wm       0                0         (0/0/0)             0
6 unassigned    wm       0                0         (0/0/0)             0
7 unassigned    wm       0                0         (0/0/0)             0
I can't make slice 2 size zero, otherwise when I run label to write the changes I get an error. Can anyone tell me what I'm missing? Thanks!

The reason you can't do this, is that the currently shipping support for Oracle VM Manager on SPARC systems is only for NFS. The paragraph you are quoting is from the base Oracle VM manual and that section applies to x86. /dev/sda is a Linux convention, not Solaris, so it wouldn't apply here.
If you go to the Oracle VM Server for SPARC documentation at Oracle VM for SPARC Documentation and then select View Library for Release 3.0 at
http://docs.oracle.com/cd/E37707_01/index.html
you will see a page with all the documents for the current release. Pick the "Oracle VM Manager 3.2: Quick Start Guide for Managing Oracle VM Server for SPARC" at http://www.oracle.com/technetwork/server-storage/vm/ovm3-sparc-quick-start-guide-1900072.pdf
You are running the correct version of Solaris 11 and the logical domains manager, so you should be able to discover the server, networks, and file-based repositories, but you'll have to wait till a later release provides support for local disk, FC SAN, and iSCSI. I hope this helps explain the situation.
Jeff

Nexus 5548 L3 daughter card flapping

Hi guys,
Anyone of you here that experienced the logs below on their Nexus box:
2011 Dec 12 06:24:45 GDCNXS5K01 %BTCM-2-BTCM_LOG_ROUTER_ERR: router card in slot 3 has internal link(s) flapped: router ports down: 0x1a108000 0x1a109000 0x1a10a000 0x1a10b000 0x1a10c000 0x1a10d000 0x1a10e000 0x1a10f000
I am getting this log at least once a day. Seems like it is shutting down the SVI of the box after the said log occured. Good thing I have enable vPC and I am able to access the NXS5K through the vCP keepalive link (mgmt).
I have two Nexus 5548, but only one is experiencing the said error.
Any inputs, suggestions would be greatly appreciated.
Thanks,
Edzel

We had this same problem this past weekend, only in module 2 on a 5596.
In our case, we had rebooted our primary Nexus and found the following message immediately preceeded the BTCM error you noted:
%$ VDC-1 %$ %NOHMS-2-NOHMS_DIAG_ERROR: Module 2: Bootup diag detected major event: Forwarding ASIC failure: Ethernet2/9 Ethernet2/10 Ethernet2/11 Ethernet2/12 Ethernet2/13 Ethernet2/14 Ethernet2/15 Ethernet2/16
We replaced the module. A "show diag results module 3" would probably show you the same thing. However, I don't think the error message will show up until you reboot.
If your flapping Nexus is secondary, you probably won't notice anything major, but if it is your primary, it would probably affect your routing.

To be unable to discover a Nexus 5548 wirth DCNM 5.2(2e)

Similar Messages

Maybe you are looking for