To configure VOIP for this 2FXO card

We are having one Cisco 3640 Router with One Serial Port and 2FXS(2nos) Voice card. We have configured the 2FXO card to the best of our knowledge. These 2 ports are configured in EPABX. Now we are able to get the dialtone but we are unable to make calls to US . Kindly let me know the commands to configure VOIP for this 2FXO card.
Thanks in advance
Regards
Sapna shah

We are having one Cisco 3640 Router with One Serial Port and 2FXS(2nos) Voice card.We have configured voice card FXO but now due to some unknown reason we are not able to call the US office. Kindly help us .Here is the configuration:
Can u let us know what errors we have made in configuruing steps .
Here are HYD-RTR#sh voice port
Foreign Exchange Station 1/0/0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is Direct line for IOC
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing Voice
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Foreign Exchange Station 1/0/1
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is Connected to Alcatel PABX thru trunk line
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 1 s
Region Tone is set for US
Analog Info Follows:
Currently processing unknown
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Foreign Exchange Station 1/1/0
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is Second Direct Line For IOC
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing Voice
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Foreign Exchange Station 1/1/1
Type of VoicePort is FXS
Operation State is DORMANT
Administrative State is UP
No Interface Down Failure
Description is Second Line Connected to Alcatel PABX thru trunk line
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing unknown
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is loopStart
Ring Frequency is 25 Hz
Hook Status is On Hook
Ring Active Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Foreign Exchange Office 2/0/0
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is plar
Connection Number is 100
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is groundStart
Number Of Rings is set to 1
Supervisory Disconnect active
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Type is pulse
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Foreign Exchange Office 2/0/1
Type of VoicePort is FXO
Operation State is DORMANT
Administrative State is UP
The Last Interface Down Failure Cause is Administrative Shutdown
Description is not set
Noise Regeneration is enabled
Non Linear Processing is enabled
Music On Hold Threshold is Set to -38 dBm
In Gain is Set to 0 dB
Out Attenuation is Set to 0 dB
Echo Cancellation is enabled
Echo Cancel Coverage is set to 8 ms
Connection Mode is normal
Connection Number is not set
Initial Time Out is set to 10 s
Interdigit Time Out is set to 10 s
Call-Disconnect Time Out is set to 60 s
Region Tone is set for US
Analog Info Follows:
Currently processing none
Maintenance Mode Set to None (not in mtc mode)
Number of signaling protocol errors are 0
Impedance is set to 600r Ohm
Voice card specific Info Follows:
Signal Type is groundStart
Number Of Rings is set to 1
Supervisory Disconnect active
Hook Status is On Hook
Ring Detect Status is inactive
Ring Ground Status is inactive
Tip Ground Status is inactive
Dial Type is dtmf
Digit Duration Timing is set to 100 ms
InterDigit Duration Timing is set to 100 ms
Pulse Rate Timing is set to 10 pulses/second
InterDigit Pulse Duration Timing is set to 750 ms
Please enlighten us why we are not able to make calls .IS there any fault in the configurations made by us !
Thanks in advance

Similar Messages

When trying to install itunes on windows 7 i got a configuration data for this product is corrupt?

It is not allowing me to install, it gives me the error: configuration data for this product is corrupt. How do I install itunes on my windows 7?
Trying to update my ipad....but I first need to install itunes!!

(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

I am trying to install iTunes in my 64 bit Windows 7 PC. My PC runs normal. But when I try to install Itunes from Apple website, i get message "The Configuration data for this product is Corrupt".

I am trying to install iTunes in my 64 bit Windows 7 PC. My PC runs normal. But when I try to install Itunes from Apple website, I get a message "The Configuration data for this product is Corrupt contact your support personneI" I
am so disgusted,please help!!!

Hey madnest,
Thanks for the question. After reviewing your post, it sounds like you are having difficulty installing iTunes in Windows. I would recommend that you read this article, it may be able to help you resolve or isolate the issue.
Issues installing iTunes or QuickTime for Windows
Thanks for using Apple Support Communities.
Have a nice day,
Mario

Java 1.4.2_03 Windows: The configuration data for this product is corrupt.

Trying to install j2SE 1.4.2_03 JRE on a Windows system (exact version needed for a bussiness application) after all previous Java installations have been deleted and all Windows Registry Java related keys have been manually deleted with Regedit.exe.
The EXE installer works properly in other machines but in this one it stops after a few seconds with the following message:
"The configuration data for this product is corrupt. Contact your support personnel".
The problem is related to the Windows install mechanism rather than the Java installer itself and likely caused by the manual Registry deletion.
The error code is 1610: ERROR_BAD_CONFIGURATION.
Reinstalling Windows didn't fix the problem.
Unable to recover the system to a previous state with the System Recovery Tool (Accesories/System Tools).
Other versions of Java installers fail the same way and show the same message.
I don't know how to contact "my support personnel" nor who they are.
I'd appreciate any help about this problem or what Java installers need within the Registry to work or a clue of any kind.

Sorry for the duplicated message. It's my first post and I messed up a little with the right section.
A new downloaded copy of the file or other versions of Java failed to install with the same error message.
I've learned there is a product ID in the registry that must be present for the installer to run. I'm searching for this "mysterious" product ID and how to set the right Windows XP Registry entry for the JSE 1.4.2_03 version.
I'm still not sure this will fix the problem.
Thanks for replying.

Java 1.4.2_03 WindowsXP The configuration data for this product is corrupt.

Trying to install j2SE 1.4.2_03 JRE on a Windows XP system (exact version needed for a bussiness application) after all previous Java installations have been deleted and all Windows Registry Java related keys have been manually deleted with Regedit.exe.
The EXE installer works properly in other machines but in this one it stops after a few seconds with the following message:
"The configuration data for this product is corrupt. Contact your support personnel".
The problem is related to the Windows install mechanism rather than the Java installer itself and likely caused by the manual Registry deletion.
The error code is 1610: ERROR_BAD_CONFIGURATION.
Reinstalling Windows didn't fix the problem.
Unable to recover the system to a previous state with the System Recovery Tool (Accesories/System Tools).
Other versions of Java installers fail the same way and show the same message.
I don't know how to contact "my support personnel" nor who they are.
I'd appreciate any help about this problem or what Java installers need within the Registry to work or a clue of any kind.

Sorry for the duplicated message. It's my first post and I messed up a little with the right section.
A new downloaded copy of the file or other versions of Java failed to install with the same error message.
I've learned there is a product ID in the registry that must be present for the installer to run. I'm searching for this "mysterious" product ID and how to set the right Windows XP Registry entry for the JSE 1.4.2_03 version.
I'm still not sure this will fix the problem.
Thanks for replying.

When i install latest itunes gives an error the configuration data for this product is corrupt.how can i i fix it

hi there
i was trying to install latest itunes it gives error
the configuration data for this product is corrupt contact your personal support
how can i fix it and what is the reason for this error

(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

Why does it say "The configuration data for this product is corrupt. Contact your support personnel." when trying to install itunes64installer on my b4 bit windows 7 acer pc? Any help would be much appreciated...

Why does it say "The configuration data for this product is corrupt. Contact your support personnel." when trying to install itunes64installer on my b4 bit windows 7 acer pc? Any help would be much appreciated...

(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

I tried to update itunes to the latest version yet it wont update. Im currently getting a error message,from Window Installer, configuration dat for this product is corru

I'm trying to update itunes but not very successful and im not making much progress. Im currently getting a message on the screen from Window Installer quoting configuration data for this product is corrupt while trying

The path 'C:\Documents and Settings\HP_Administrator\Local Settings\Application Data\Apple\Apple Software Update\iTunes.msi' cannot be found. Verify that you have access to this location and try again, or try to find the installation package 'iTunes.msi' in a folder from which you can install the product iTunes.
Unfortunately, this sort of trouble has gotten more complicated to deal with ever since Microsoft pulled the Windows Installer CleanUp utility from their Download Center on June 25. First we have to find a copy of the utility.
Let's try Googling. (Best not to use Bing, I think.) Look for a working download site for at least version 3.0 of the Windows Installer CleanUp utility. After downloading the utility installer file (msicuu2.exe), scan the file for malware, just in case. (I use the free version of Malwarebytes AntiMalware to do single-file scans for that.)
If the file is clean, to install the utility, doubleclick the msicuu2.exe file you've downloaded.
Now run the utility ("Start > All Programs > Windows Install Clean Up"). In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove".
Quit out of CleanUp, restart the PC and try installing iTunes again. Does the install go through properly now?
(If you do find a clean download site for the correct version of CleanUp, please don't tell me where it is. Without wishing to sound paranoid (although I grant it does sound paranoid), there is a non-zero chance that posting links to download locations for the utility here at Discussions leads to that download location being shut down.)

Bonjour64 error: "The configuration data for this product is corrupt. Contact your support personnel."

Have use WinRAR to pull out only Bonjour64 from iTunes 11.1.5 (and prior releases) to do an install of only Bonjour, as all other iTunes-related software loads fine (have used 11.1.4 and new 11.1.5). I get the error: "The configuration data for this product is corrupt. Contact your support personnel." Have tried everything suggested on net and this forum, including uninstalling everything, cleaning registry, disabling firewall, etc. Not worthwhile to reinstal Windows 7. What do I do?

(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page). Here's a screenshot showing the particular links on the page that you should be clicking:
After clicking one of the circled links, you should be taken to another page, and after a few seconds you should see a download dialog appear for the msicuu2.exe file. Here's a screenshot of what it looks like for me in Firefox:
Choose to Save the file. If the dialog box does not appear for you, click the link on the page that says "CLICK HERE IF IT DOES NOT". Here's a screenshot of the page with the relevant link circled:
When the dialog appears, choose to save the file.
(2) Go to the Downloads area for your Web browser. Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
4) In the list of programs that appears in CleanUp, select any Bonjour entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

Trouble configuring Xserver for multiple graphics cards

I suspect I have a fairly simple problem but am getting in over my head and need some help setting up a multihead X configuration.
I have a plain vanilla installation of Solaris 9 on an Ultra 60, 1.5GB, 2x450 MHz CPUs, originally configured with one Elite3D lite card in the 64 bit/66 MHz PCI slot as a single head installation. All ran fine.
I have now added a pair of Elite3D-m3 cards in the 2 UPA slots. At boot, the Elite3D in the first UPA slot comes up as the character mode console device and the OS boots normally up to the point of starting X/CDE desktop then defaults to the console login with " ...could not start X server..." error message .
I configured the Xservers file to include the two Elite as the default display :0.0 on /dev/fbs/afb0 and /dev/fbs/afb1, but on closer examination, found that the devices do not exist in /dev or /dev/fbs.
I do have a device /dev/fbs/ifb0 corresponding to the Expert3D lite card, known to function normally as a single headed machine.
Here are the questions:
1. How do I obtain and install the necessary device files, /dev/fbs/afb0 and /dev/fbs/afb1 to allow the two Elite3Ds to drive 2 monitors under X/CDE? What are the necessary packages needed to drive the Elite3Ds?
2. In the meantime, how can I start the Xserver in the expert3D card? The Xserver will not start (gives errors) by simply defining :0.0 to be /dev/fbs/ifb0 (Expert3D lite) in /usr/dt/config/Xserver. This device is not the default Solaris character mode boot console device, so I am not sure how to set up the Xserver file to run the X session on this card **alone** to tide me over pending Elite3D's configured and running and the new monitors are delivered.
I recall that CDE and X require special consideration for this situation where the boot console device and the graphical device to run X are not identical. The Xservers file comments refer to this problem but I cannot seem to find sufficient documentation to figure out how to configure this situation.
I would like to avoid ripping out the two just installed cards to get back to the original configuration.
Thanks for the help in advance.

Please note the following erratum: The original configuration was with an Expert3D lite in the 64bit/66 MHz PCI slot, not an Elite3D. Thanks.

Added additional user. How do I configure password for this user?

Have two different accounts. Second accound added but don't understand how to cinfigure password for this account.

A bit confused by your query, so can you clarify a few points.
re: added additional user
You do not add additional users to Thunderbird, so I presume you mean you have tried to create another mail account for someone else in your own profile.
You do not configure passwords for other peoples email addresses as that would be a privacy issue and only they should do it.
Lets start at the begining.
If more than one person is using a computer, they should have their own User Account which they access via a password they choose. This gives them their own desktop view and access to programs installed on computer, such as Thunderbird.
Thunderbird will be available for them to use.
When you run it for the first time in their User Account, it will create a Profile in their User Account.
Thunderbird will also then ask you to create a mail account in that Profile.
The details you enter will ask for Name. email address and a password.
That password is the same password they use to access their email in their webmail account using a browser, so only they should know that password and they should not divulge it to anyone - however in some cases, eg: spouses, they may know each others password.
You can choose whether Thunderbird remembers the password or not before creating the account, but the password would still be required to configure the mail account.
This method means that no one can see that persons emails nor access their password details because they do not know the password to the computer User Account.
If you have only the one admin User Account which several people use, then anyone has access to anything on that computer. This may be fine if eg; spouses share the computer, but it is not a practise that should be used in any other environment.
If you have mail accounts created in the same Thunderbird profile, then all mail and passwords are freely available for anyone to see and this may not be desired.
Some people use only the one User Account, but they have their own Profile created in Thunderbird.
When Thunderbird was initially run, it created a defult Profile, but you can add additional Profiles using the Profile Manager.
The mail account is created in that Profile and then they can apply a Master Password in Thunderbird.
This means that anyone can still see anyone's emails as on startup as anyone can select any Profile.
But, the access to passwords is locked and removal of Master Password will remove all stored paswords to safe guard privacy.
Some info on Master Passwords:
* http://kb.mozillazine.org/Master_password
Some info on creating additional Profiles using Profile Manager:
* http://kb.mozillazine.org/Profile_Manager

Crawled the UCM through SES but unable to search on Search screen. I have to use OID as identity management. How to configure SES for this??

I have crawled the UCM through SES, but when I try to search on the Search screen nothing is searched.
followed the following document - http://www.oracle.com/technetwork/search/oses/stellent-white-paper-178229.pdf
But at the end I need to configure the identity management for OID not for Content Server. I have activated the OID plug-in in SES, but nothing is searched in both the foloowing cases:
1) When I login with a OID user
2) When i do not login, even the public data is not displayed.
What could be the problem??

Thanks for the reply. Authorization was use source ACL, and I tried logging in as every user that had access to the content and could not bring up anything.
However, this is no longer an issue as we are not going to be using this content database. We are going to be using the new Beehive collaboration instead. I don't know if there will be a different plugin for SES or what, but it should be interesting.
Jennifer

VI Analyzer - How Would You Configure It for This Use Case?

My group has different people working on different LVPROJs for each software deliverable we have. Each LVPROJ uses our user.libs and instr.libs, as well as an overall "framework" that is the same for most LVPROJs.
I really think the VI Analyzer toolkit would be powerful for code reviews, but only if I can configure it in a way where which tests I run and what the criteria are can be saved and used on any project. I can't seem to get this to work for me. I want to save all those configurations, and use it on new LVPROJs easily - the easier I can make this process, the more inclined others will be to use this for code review. How would you do it? (if it's even feasible)
Solved!
Go to Solution.

I suggest creating a .cfg file without a project linkage, but with all the tests selected and configured as you want...so a .cfg file with no "Items to Analyze" specified. Then, when working on an individual project, open that CFG file, add the project's top-level folder to the analysis, then save that CFG file with that project. This means you can't have the project linkage in your CFG file, but assuming your project is all within some top-level folder, that shouldn't be much of an issue, since the CFG file will be "linked" at that point to the top-level folder containing your project.
Darren Nattinger, CLA
LabVIEW Artisan and Nugget Penman

Integrated Configuration - Possible for this scenario?

Hi experts,
Could you please tell me if Integrated Configuration would work in this scenario, if so could you please tell me how.
A file is read and accordingly a RFC call is made. The response of the RFC is used to determine receivers. The receivers are other RFC's and IDoc's to different systems.
I was planning to use the receiver determination step in BPM to achieve this.
I am on PI 7.11
Thank you.
Radhika.

> Could you please tell me if Integrated Configuration would work in this scenario, ...
No. You cannot use IC in combination with BPM.

I want to run whatsapp on my ipod can i use iphone configuration utility for this

PLze tell can i do it

Hey Abhi 18, Sorry-- I'm out of touch. Was not aware of the method of using an iPhone as a hat. I watched the link Illaass supplied, a little work, but it appears to work. Is it safe? I can't answer that, haven't done it, so I don't know. But I would think Illaass would not have given the link if it were not. Cheers.

To configure VOIP for this 2FXO card

Similar Messages

Maybe you are looking for