To disable interleaving on my line

How can I get interleaving disabled on my line to improve gaming ping for xbox?
Thanks.
Solved!
Go to Solution.

Hi, how long does switching to fastpath usually take?
A week later and my router still says -
ADSL settings
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.1
Latency type
Interleaved
Noise margin (Down/Up)
7.0 dB / 23.0 dB
Line attenuation (Down/Up)
17.0 dB / 9.0 dB
Output power (Down/Up)
19.8 dBm / 12.3 dBm
Loss of Framing (Local)
2
Loss of Signal (Local)
2
Loss of Power (Local)
0
FEC Errors (Down/Up)
39200 / 17
CRC Errors (Down/Up)
217 / N/A
HEC Errors (Down/Up)
N/A / 8
Error Seconds (Local)
35

Similar Messages

Disable autologin via command line

Is it possible to disable autologin via the command line?

To be more specific, the user's name is recorded as the value of the 'autoLoginUser' property in the "/Library/Preferences/com.apple.loginwindow.plist" file. As such, given sufficient privileges, 'defaults' or 'PlistBuddy' can be used to specifically remove that property, eg. from an "admin" account, assuming "automatic login" is enabled:<pre>
defaults delete /Library/Preferences/com.apple.loginwindow autoLoginUser</pre>
If you are referring to the "System Preferences" > "Security" setting to "Disable automatic login", a further change, in addition to the above, is required. Again, from an "admin" account:<pre>
defaults write /Library/Preferences/.GlobalPreferences com.apple.userspref.DisableAutoLogin -bool true</pre>
But this second setting doesn't seem to do much more than, combined with the first change, cause the "Disable automatic login" checkbox to appear enabled...

CCA 8 - Disable second call on line 1

Where in CCA version 8 can we disable the second call on any extension? Is it possible?

Hi William,
Have a look at these 3 good threads that detail this issue.
https://supportforums.cisco.com/message/3246737#3246737
https://supportforums.cisco.com/message/3088569#3088569
https://supportforums.cisco.com/message/3125246#3125246
It looks like you need to use the cli with Huntstop Channel if you
are using Dual Line DN's and the CCA (Busy Trigger = 1) if using
Octo Line DN's
Cheers!
Rob

MS patches that say "Disabled" in the subject line?

So using patch policies, I notice a bunch that say (Disabled) in the actual subject of the patch.
Example:
MS 2719662 Workaround for Vulnerability in Windows Sidebar and Gadgets (Disabled) (See Notes)
what does that mean? (the patch is cached, and not Disabled as far as ZPM goes). Does that mean that Novell/Lumension Disabled the patch or that MS Disabled it?
If it's Disabled by MS, then why does it show up as being needed (not patched)?

Ah, so that's what it means (the "notes" don't say that). And of course, that causes all sorts of issues with Patch Policies (guess they didn't really think that part through).
Fortunately my friend Susan has about 5 SR's and multiple bugs with Patch Policies for me. Now that you're not there.

Disable line item display in KE30 Reports

Hi,
Has any one tried disabling line item display in a KE30 Report? Which authorization object can be used to disable the access to line items?
Thanks for your time.
Regards,
SAP_CO1

Hi,
When you create user-defined authorization objects for reporting, all their fields will be checked when you execute a report, even if they are not used in the report. It is not necessary to have all fields in the report definition, but you will need at least authorization ':' to get the aggregated figures.
Example:
Authorization object contains fields WW001, WW002
Report uses field WW001 as drilldown characteristic, but not WW002.
To execute the report, the user needs authorization '*' for field WW001 and ':' for WW002.
If he does not have authorization for WW001 then he can execute KE30 but cannot drilldown to line items
For more information how authorization checks for user-defined authorization objects work, you can refer to the IMG documentation via CO-PA -> Tools -> Authorization Management ->CO-PA specific Authorization objects -> Define authorization objects for the information system.
You may use transaction SU24 in order to check the assignment of authorization objects to transaction KE30.
regards
Waman

Disable Field for Line Details Form

How do I trap an event on a Line Details form to disable a field?
The FormType for all the Line Details forms is 1 so I cannot differentiate one from the other. Also, there does not seem to be a Form Mode for Line Details forms so I cannot differentiate Add mode from Update.
Any insight is appreciated.
Thanks.

Don't think you can disable a field in line detail. You can only disable a column... SDK didn't even allow you to disable a row in a line details-matrix, let alone a field... Let us pray then

BADI BBP_UI_CONTROL_BADI for disabling fields item wise in PO!

Hi all,
We are working on SRM 5.0(SP12),ECS.
I need to disable the account assignment fields like G/L account,Cost centre for the PO in Process PO transaction only for users with the role BUYER for all line items in the PO.
For users with the role of EMPLOYEE/REQUISITIONER,i need to disable the a/c assignment fields mentioned above only for all the line items in the PO except the first line item.
Can anyone confirm whether this can be achieved using the BADI "BBP_UI_CONTROL_BADI".
I have earlier disabled/enabled fields using this BADI but irrespective of the number of line items in the document.CAn i achieve the disabling effect at the line item level i.e. can i control the table control display for multiple lines in the PO?

Yes..I think you can..but not sure...Try to debug the BADI and play around and see if you are able to do it, then you can code it accordingly.
Regards, IA

Issue with Disabling one of the menu item in Forms6i

Hi,
I have a requirement where I need to disable the IR/PO Information (menu item) created using Form Personalization in Sales Order form.
If the Warehouse is other than ‘FIM’ it should be disabled for that particular line.
Please let me know if anybody has done the similare requirement???
Regards,
Bala

Bala,
I can suggest one work around.
Say your menu entry is special1.
You probably already have a personalization that fires for trigger event = special1.
You can add a condition in that personalization that says warehouse=FIM.
This way, the PO information screen will come up only for FIM.
You can consider creating a new personalization that fires for same trigger event = special1.
The condition says warehouse != FIM
In the actions, you can say "This menu option is not available"
Hope this helps,
Sandeep Gandhi

Recent change from interleave to fastpath

Hello
I recently requested an change in the latency type for my internet from interleave to fastpath (my son plays online games and said it would be better) so I emailed the moderation team on this site for the change of which they have done.
But now it seems the line is so unstable that its very hard to connect if at all, I was under the impression that should the stats on my line be insufficient that it would not be enabled but alas that doesnt seem to be the case.
The stats I emailed to the moderation team (before fastpath) were as follows:
Channel: INTR, Upstream rate = 448 Kbps, Downstream rate = 5568 Kbps
Link Power State: L0
Mode: G.DMT
Channel: Interleave
Trellis: ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 9.3 25.0
Attn(dB): 43.0 22.0
Pwr(dBm): 19.6 12.3
Max(Kbps): 6080 1208
Rate (Kbps): 5568 448
I have had to fiddle with some router settings (Netgear DG834Gv4) to be able to connect and even then it takes a while to even connect.
I have noticed that if the SNR ratio becomes 15 then it connects no problem but anything lower is little point in trying and 15 makes the download speed drastically slower.
I have asked the moderation team (which i apologised for multiple emails) if they could turn interleave back on (which I hope they can do as swiftly as possible) but out of curiosity why is it that fastpath has hurt the connection so much? And is there anything I can do for my son so he can play his online games better with a lower latency, he says sometimes people from other countries get a better *ping?* than he does on a uk server.
Many thanks

Hello and thanks for responding
I ran that 17070 quiet line test and there doesnt really appear to be any noise down the phone, maybe the slight very tiny ammount of noise but only on the odd occassion.
speedtester results:
Download speedachieved during the test was - 3543 Kbps
For your connection, the acceptable range of speedsis 1200-4000 Kbps.
Additional Information:
Your DSL Connection Rate :4320 Kbps(DOWN-STREAM), 448 Kbps(UP-STREAM)
IP Profile for your line is - 3500 Kbps
The throughput of Best Efforts (BE) classes achieved during the test is - 13.39:22.37:64.24 (SBE:NBEBE)
These figures represent the ratio while sententiously passing Sub BE, Normal BE and Priority BE marked traffic.
The results of this test will vary depending on the way your ISP has decided to use these traffic classes.
2. Upstream Test: -provides background information.
Upload Speed
360 Kbps
0 Kbps
448 Kbps
Max Achievable Speed
Here are the stats i can produce from my router:
System Up Time 01:31:47
Port
Status
TxPkts
RxPkts
Collisions
Tx B/s
Rx B/s
Up Time
WAN
PPPoA
872226
869609
0
7126
230989
01:30:46
LAN
10M/100M
871078
873888
0
231608
10833
01:31:41
WLAN
11M/54M
1242
652
0
42
13
01:31:31
ADSL Link
Downstream
Upstream
Connection Speed
4320 kbps
448 kbps
Line Attenuation
42.0 db
22.0 db
Noise Margin
14.6 db
24.0 db
usr/sbin/adslctl: ADSL driver and PHY status
Status: ShowtimeRetrain Reason: 8000
Channel: FAST, Upstream rate = 448 Kbps, Downstream rate = 4320 Kbps
Link Power State: L0
Mode: G.DMT
Channel: Fast
Trellis: ON
Line Status: No Defect
Training Status: Showtime
Down Up
SNR (dB): 14.6 24.0
Attn(dB): 42.0 22.0
Pwr(dBm): 19.2 12.1
Max(Kbps): 4352 1116
Rate (Kbps): 4320 448
G.dmt framing
K: 136(0) 15
R: 0 0
S: 1 1
D: 1 1
ADSL2 framing
MSGc: 1 1
B: 136 15
M: 1 1
T: 1 1
R: 0 0
S: 1.0000 1.0000
L: 1096 128
D: 1 1
Counters
SF: 323850 323797
SFErr(CRCErr): 3474 11
RS: 0 0
RSCorr: 0 0
RSUnCorr: 0 0
HEC: 1636 5
OCD: 0 0
LCD: 0 0
Total Cells: 56091767 0
Data Cells: 26593926 0
Drop Cells: 0
Bit Errors: 0 0
ES: 2337 0
SES: 0 0
UAS: 35 0
AS(Uptime): 5506
INP: 0.00 0.00
PER: 1.75 1.75
delay: 0.25 0.25
OR: 32.00 32.00
Bitswap: 0 0
Total uptime: 5506
Total time = 1 hours 32 min 41 sec
SF = 323850
CRC = 3474
LOS = 0
LOF = 0
ES = 2337
Latest 1 day time = 1 hours 32 min 41 sec
SF = 323850
CRC = 3474
LOS = 0
LOF = 0
ES = 2337
Latest 15 minutes time = 2 min 41 sec
SF = 9499
CRC = 112
LOS = 0
LOF = 0
ES = 84
Previous 15 minutes time = 15 min 0 sec
SF = 52923
CRC = 577
LOS = 0
LOF = 0
ES = 319
Previous 1 day time = 0 sec
SF = 0
CRC = 0
LOS = 0
LOF = 0
ES = 0
15 minutes interval [-30 min to -15 min] time = 15 min 0 sec
SF = 52982
CRC = 589
LOS = 0
LOF = 0
ES = 405
15 minutes interval [-45 min to -30 min] time = 15 min 0 sec
SF = 52923
CRC = 597
LOS = 0
LOF = 0
ES = 394
15 minutes interval [-60 min to -45 min] time = 15 min 0 sec
SF = 52923
CRC = 546
LOS = 0
LOF = 0
ES = 376
Showtime Drop Reason: 8000
Last Retrain Reason: 8000
usr/sbin/adslctl: ADSL driver and PHY statusStatus: ShowtimeRetrain Reason: 8000Channel: FAST, Upstream rate = 448 Kbps, Downstream rate = 4320 KbpsLink Power State: L0Mode: G.DMTChannel: FastTrellis: ONLine Status: No DefectTraining Status: Showtime Down UpSNR (dB): 14.6 24.0Attn(dB): 42.0 22.0Pwr(dBm): 19.2 12.1Max(Kbps): 4352 1116Rate (Kbps): 4320 448 G.dmt framingK: 136(0) 15R: 0 0S: 1 1D: 1 1 ADSL2 framingMSGc: 1 1B: 136 15M: 1 1T: 1 1R: 0 0S: 1.0000 1.0000L: 1096 128D: 1 1 CountersSF: 323850 323797SFErr(CRCErr): 3474 11RS: 0 0RSCorr: 0 0RSUnCorr: 0 0
HEC: 1636 5OCD: 0 0LCD: 0 0Total Cells: 56091767 0Data Cells: 26593926 0Drop Cells: 0Bit Errors: 0 0
ES: 2337 0SES: 0 0UAS: 35 0AS(Uptime): 5506
INP: 0.00 0.00PER: 1.75 1.75delay: 0.25 0.25OR: 32.00 32.00
Bitswap: 0 0Total uptime: 5506
Total time = 1 hours 32 min 41 secSF = 323850CRC = 3474LOS = 0LOF = 0ES = 2337Latest 1 day time = 1 hours 32 min 41 secSF = 323850CRC = 3474LOS = 0LOF = 0ES = 2337Latest 15 minutes time = 2 min 41 secSF = 9499CRC = 112LOS = 0LOF = 0ES = 84Previous 15 minutes time = 15 min 0 secSF = 52923CRC = 577LOS = 0LOF = 0ES = 319Previous 1 day time = 0 secSF = 0CRC = 0LOS = 0LOF = 0ES = 015 minutes interval [-30 min to -15 min] time = 15 min 0 secSF = 52982CRC = 589LOS = 0LOF = 0ES = 40515 minutes interval [-45 min to -30 min] time = 15 min 0 secSF = 52923CRC = 597LOS = 0LOF = 0ES = 39415 minutes interval [-60 min to -45 min] time = 15 min 0 secSF = 52923CRC = 546LOS = 0LOF = 0ES = 376Showtime Drop Reason: 8000Last Retrain Reason: 8000
Sorry if there is too much information there. There is an option on my router to change a percentage on SNR as I read somewhere this may improve stability, My normal snr is 9db on the downstream but I cannot connect on that, i changed the setting so that its 14.6db but it still takes such a long time to connect, and the download speed is dropped dramatically.
Unless theres something obvious in these stats that Im missing I would very much rather have interleave turned back on asap so that the internet actually works as intended

Disabling Payment term

Dear Experts:
I want to disable payment terms at line item level for customer invoice because i dont want users to change it to save proper aging of overdue invoices. Please tell how will it be disabled at line item level.
Regards
Atif

Hi ,
Do you want the payment term to the in display mode at the time of posting or after posting the document .
In OB32 you can make the settings for document change rules after posting .
you can set the field status group settings at GL account level OBC4 or at Posting key level OB41.
FInally if above is not feasible to you then you will have to go for screen varient SHD0.
Regards ,
Dewang T

C819G-4G-V-K9 help (no ip address) Cellular0 is up (spoofing), line protocol is up (spoofing)

We recently purchased a C819G-4G-V-K9 for a remote site that has no ISP available. I can't seem to get this working properly. I can tell the cell portion is up and working becuase I can send the router a text message and I receive it on the router. The cell 0 interface however, is not getting a dhcp address. Below is my configuration:
hostname Router
boot-start-marker
boot system flash:c800-universalk9-mz.SPA.153-3.M.bin
boot-end-marker
aqm-register-fnf
no aaa new-model
memory-size iomem 10
ip cef
no ipv6 cef
multilink bundle-name authenticated
chat-script lte "" "AT!CALL1" TIMEOUT 60 "OK"
license udi pid C819G-4G-V-K9 sn FTX180680R8
vtp domain MobileCell
vtp mode transparent
controller Cellular 0
interface Cellular0
ip address negotiated previous
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer string lte
dialer-group 1
async mode interactive
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface GigabitEthernet0
no ip address
shutdown
duplex auto
speed auto
interface Serial0
no ip address
shutdown
clock rate 2000000
interface Vlan1
ip address 192.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Cellular0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0
dialer-list 1 protocol ip list 1
access-list 1 permit any
control-plane
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
mgcp profile default
line con 0
script dialer lte
no modem enable
line aux 0
script dialer lte
modem InOut
no exec
line 2
no activation-character
no exec
transport preferred none
transport input all
stopbits 1
line 3
script dialer lte
modem InOut
no exec
line vty 0 4
login
transport input all
scheduler allocate 20000 1000
end
Cellular0 is up (spoofing), line protocol is up (spoofing)
Hardware is 4G WWAN Modem - Verizon Multimode LTE/eHRPD/EVDO RevA/Rev0/1xRTT
Internet address will be assigned dynamically by the network
MTU 1500 bytes, BW 9 Kbit/sec, DLY 100000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
     DCD=down DSR=down DTR=up RTS=up CTS=up
Router#sh ip int bri
Interface                  IP-Address      OK? Method Status                Protocol
Cellular0                  unassigned      YES manual up                    up
FastEthernet0              unassigned      YES unset down                  down

Not sure if you solved your problem yet, but my Cell0 has a few extra lines. I also have a static IP, so it might not be exactly the same as yours.
interface Cellular0
ip address negotiated
no ip unreachables
ip nat outside
ip virtual-reassembly in
encapsulation slip
load-interval 30
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer watch-group 1
async mode interactive
routing dynamic
ip sla auto discovery
access-list 100 permit ip any any
dialer watch-list 1 ip 5.6.7.8 0.0.0.0
dialer watch-list 1 delay route-check initial 60
dialer watch-list 1 delay connect 1
dialer-list 1 protocol ip permit
Cellular0 is up, line protocol is up
Hardware is 4G WWAN Modem - Verizon Multimode LTE/eHRPD/EVDO RevA/Rev0/1xRTT
Internet address is xxx.xxx.xxx.xxx/32
MTU 1500 bytes, BW 50000 Kbit/sec, DLY 100000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 264
Queueing strategy: fifo
Output queue: 0/10 (size/max)
30 second input rate 11000 bits/sec, 16 packets/sec
30 second output rate 11000 bits/sec, 16 packets/sec
     1242186 packets input, 660512785 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     1164618 packets output, 233386561 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
     DCD=up DSR=up DTR=up RTS=up CTS=up

Line Reset

Hello there,
I was just wondering if it was possible for an Openreach engineer to perform a line reset at all? If possible, it would be great to go back to the open profile I was on before and it was my fault to reboot the router several times during the stabilisation which obviously would have messed DLM up (which has put a major amount of interleaving on my line).
BT Home Hub Manager - Information for Helpdesk agents:
BTW Performance Test:
ADSL Checker:
Solved!
Go to Solution.

you need an engineer visit before you will get a reset and from looking at your stats compared to your estimate I think that unlikley unless you can show you have a problem with your conenction and not just interleaving. if engineer visit and no fault you may get charged £129.99
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

DepthTest.DISABLE not working for my node?

Hello all!
I basically have a root container with 3D objects with a Perspective Camera set up in the scene; however I have a JFXtras Window set up as a List and a GridView via ControlsFX. I am Using the GridView to also Display 3D content, and I want to turn the DepthTest to Disable, however it isn't working.
I have tried setting
window.setDepthTest(DepthTest.DISABLE);
GridView.setDepthTest(DepthTest.DISABLE);
setDepthTest(DepthTest.DISABLE); //This and the line below are for the CellFactory of the GridView, to see if either worked on the cell's themselves.
setDepthTest(DepthTest.DISABLE);
Not too sure if I am doing something wrong, or if I should report this to Jira? Thanks!

phelpy wrote: Ive tried using another charger and the same thing happened, no green light.
Does not sound so good.
Start here:
http://support.apple.com/kb/ts1713
If you are still under warranty, no fee.
https://selfsolve.apple.com/agreementWarrantyDynamic.do

Getting interleaved turned off

I know this is a Mod job, but I may as well post here too in case someone has any ideas as to why its been applied.
When I first moved in to this house a few months back, I was on a fastpath connection, now its dropped to interleaved, despite the line spec and quality being well above average. The 10 days uptime is only because I moved the router power supply to another socket. I've seen 20+ days on it since moving in.
Download speedachieved during the test was - 6.46 Mbps
For your connection, the acceptable range of speeds is 0.6 Mbps-7.15 Mbps.
Additional Information:
Your DSL Connection Rate :8.13 Mbps(DOWN-STREAM), 0.45 Mbps(UP-STREAM)
IP Profile for your line is - 7.15 Mbps
Connection Information
Line state:
Connected
Connection time:
10 days, 17:07:10
Downstream:
7.938 Mbps
Upstream:
448 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.1 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
17.9 dB / 26.0 dB
Line attenuation (Down/Up):
5.5 dB / 2.0 dB
Output power (Down/Up):
12.0 dBm / 12.3 dBm
FEC Events (Down/Up):
56864 / 3
CRC Events (Down/Up):
47 / 3
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
86 / 1
Error Seconds (Local/Remote):
40 / 1

Hi
I am sorry to see you are having problems
I suggest you contact the forum mods they should be able to get this problem sorted for you this is a link to them http://bt.custhelp.com/app/contact_email/c/4951
They normally reply by email or phone directly to you within 3 working days they will take personal ownership of your problem until resolved and will keep you informed of progress
They are a UK based BT specialist team who have a good record at getting problems solved
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Creative Cloud: "Build" MSI Hangs During SCCM OSD Task Sequence Installation

I wanted to share problem and solution I found when deploying Creative Cloud Packager-created packages/application using SCCM 2012 R2. I encountered this problem packaging this as both a Package and as an Application in SCCM.
When installing the software through SCCM Software Center onto a client, Software Center would close right as the installation of the "Build" folder MSI completed. This is abnormal behavior.
When installing the application as part of an OSD Task Sequence, the software would get installed (as shown by logs) but SCCM would hang forever at the "Installing Application" step.
I tried all sorts of different settings in SCCM and with the MSIEXEC command line and eventually traced it to the Reboot Manager functionality in MSIEXEC that will close and attempt to restart processes using files that the installer needs. Reboot Manager clobbered part of SCCM and in the Task Sequence, the connection between SCCM and the installer was broken.
The solution is to pass the property "MSIRESTARTMANAGERCONTROL=Disable" along the command line when calling MSIEXEC on the Build folder MSI file. This setting disabled Restart Manager so it didn't mess up SCCM. Once I did this, my Software Center installs and OSD Task Sequences ran as intended.
For reference, I used the REBOOT=ReallySuppress property for reboots and let SCCM determine what to do with reboots based on the return code. My testing was done with Windows 8.1 Enterprise x64.

Like said, did you configure my proposal: "Configuration Manager client will force a mandatory device
restart" ? After you've configured that, update your deployment type manually and remove the old revisions of the application and try running the TS again. I'm guessing you're a little bit too fast on your doings so the ConfigMgr doesn't play a long very
nicely...
The TS stops because of your Hard Reboot (exit code 1641), I've seen this before and I configured my application so that ConfigMgr client will force device restart and that fixed my problem. Although, also my application is the last one in the TS, but still,
the TS continues after the reboot.
Btw. have you tried changing your command line to:
msiexec.exe /i cd-ord.msi TRANSFORMS=sv-se.mst MVLICENSE_KEY=xxxxxxxxxxxxxxxxx /L*V "%temp%\cdord.log" /qn
/norestart

To disable interleaving on my line

Similar Messages

Maybe you are looking for