To make 10.4.11 boot disk

I upgraded from 10.4.9 to .11 on my MacBook. Now I need to do a repair from utility, but my install .9 disk will not load. How can I download or create a .11 boot disk with repair option?
I am in Africa and pay by the minute..! so I will only be able to check mail periodically.
Thank you,
Bob, kc7eav

Thank you for your sharing of experience and interest.
The original install disk will not boot at startup, but I can select it from with prefs>startup drive.
This will probably be the best I can do, but if I have a major issue with the MacBook I will not be able to startup from a boot disk.
I am suspecting that there was a problem with the upgrade via the download to .11. The drive will also not reboot to target with holding the T key. Again, I can only select the Target mode from the prefs>startup file.
Well, Thank you very much. Goodbye from Bujumbura, Burundi, Africa!
Bob, kc7eav

Similar Messages

DiskWarrior Boot Disk NOT Booting

Here's an odd one:
I attempted to start-up from a boot disk containing OS 9.1 and DiskWarrior so I could run DiskWarrior on my hard-drive for routine maintenance.
Everything went okay until I got to the OS 9.1 screen with the progress bar and icons across the bottom. When 3 icons appeared the start-up process stopped dead and the cursor froze.
I restarted from the boot-disk several times with the same result. It stalled at the exact same spot, only sometimes the cursor froze and sometimes it didn't freeze.
I then started normally from my hard-drive OS and ran DiskWarrior on the boot-disk. But even that didn't solve the stalling when I tried again.
Any ideas what happened? I haven't touched the Zip boot-disk since last using it.
I guess I'll have to make a new Zip boot-disk. Maybe I'll make 2 of them. Erase this one and start over and make a back-up. I never liked the Zip boot-disk method as they seem like glorified floppies, but I couldn't find the older version of DiskWarrior on CD.
Thanks!

Hi, Paul.
Your Zip disk may be fine for a while if it was reformatted without incident, but if I were going to rely on Zip disks for emergency booting and running utilities from, I'd keep at least two duplicate Zips around.
Question: Can I transfer the data from my Zip Rescue boot disk (OS 9.1 & DiskWarrior) onto a Compact Flash card (in my PC card slot with adapter) and then put the CF card into the Kanguru CD burner and make a bootable CD for running DiskWarrior on my hard-drive?
I don't know for sure, but I doubt it. For one reason, I suspect the Kanguru drive probably burns all CDs in ISO 9660 format, which is cross-platform and almost universally compatible. But I don't think a Mac can boot to a CD in that format.
Secondly, there are some special requirements for a bootable CD, and just copying a bootable System Folder from another drive onto a CD doesn't make the CD bootable. Apple's Disk Burner application can't make a bootable CD at all, and making one with Roxio's Toast disk-burning application is a more complicated procedure than just burning an ordinary CD, though I don't know precisely what it does. I do know that since nothing can be written to a CD once it's been burned and closed, a bootable CD can't contain any software of any kind that insists on writing preferences, settings, or anything else to the startup disk. And any software that needs (for example) a prefs file to be in place before it can run will require you to create that file appropriately on the source from which the CD is burned, before burning it.
You may want to try booting to your CompactFlash card itself. Of course a CF card is much more expensive than a blank CD or even a Zip disk, but if you can't trust Zips and you can't presently burn bootable CDs, maybe a bootable CF card would be a useful temporary expedient until you get a general-purpose CD burner and appropriate burning software. I don't recall whether a Wallstreet can boot to a CF card in a CardBus adapter. To give it a try, hold down Command-Option-Shift-Delete (rather than "c") while powering up. If the card is bootable and your hard drive is the only other available bootable device, the PB should boot to the card.

Unable to Log and Capture AND make FCP a boot disk

I am unable to go into Log and Capture mode in FCP 4. I can capture from firewire using I movie just fine so I know the sytem works. The minute I open Log and Capture from within FCP (with the JVC Mini-DV camera hooked up thru Firewire), it crashes. Help. I upgraded from FCP 3 to FCP 4 a couple years ago and it hasn't worked right since. Would re-installing the FCP 4 upgrade work? Also, my system works very sluggish. Please explain to me how I would make the veersion of FCP 4 my boot disk. I realize that I can't have the FCP 4 application and the media on the same drive but is there a way to partition one of my drives and make FCP one of the startup disks? Hope this isn't too confusing. Thanks.

First off, FCP 4 was darn unstable. FCP 4.5 is a free upgrade and is STILL the most stable version out there. FCP 5 is getting there.
Secondly, try:
Shane's Stock Tip Mantra: If the program was working fine, and now isn't, or just isn't working the way it should, the first things to do are:
1) Trash your FCP preferences. Download the appropriate version of FCP Rescue at http://fcprescue.andersholck.com/ and run it.
2) Open the Disk Utility and Repair Permissions.
As for partitioning the hard drive, that isn't necessary. Hasn't been since FCP 3.
Shane

Is there any way to make a snow leopard partition on an early 2011 MacBook Pro that was upgraded to Lion, without the original boot disk?

So I have an early 2011 MacBook pro, I believe it shipped with snow leopard originally, as I purchased and upgraded to Lion fairly early on. I am trying to make a partition right now and have it run snow leopard so I can use programs that have PowerPC.
I should note, I replaced both the RAM and the harddrive in my Macbook pro. I changed from 4 GB of ram (that came shipped) to 8 GB of ram from a 3rd party, that I installed on my own months ago, have registered in the computer and have been working fine for quite some time now.
Also I should note I replaced my harddrive. I went from what ever the standard 500 GB harddrive that shipped with 15 inch early 2011 MB pro's. I now have a 3rd party SSD that's 240GB's that I also installed on my own, (at the same time as the RAM---Black friday items) The harddrive has been working just fine since then.
In installing the harddrive I borrowed a friends external harddrive and used a program called carbon copy cloner to get everything over to the SSD.
Now here is my issue. I have ordered the Snow Leopard (10.6.3) install disks from apple, I have created a partition on my SSD for snow leopard, but when I try to select the install disc for snow leopard at boot I get three beeps.
I know this issue has been posted elsewere but it said answered and the answer is no longer available. I also am unsure if any of the RAM or Harddrive swapping could have been causing the issue. I have the old harddrive and RAM still, but unfortunatley have no external harddrive anymore or money to afford one.
Is there any way I can install a partition that runs snow leopard on my early 2011 MB pro with what I have (new SSD, New RAM, Current version Lion running, no external drive, lack of original snow leopard disks [I lost them ] and the general 10.6.3 snow leopard boot disks).
Let me know If there is anything I can do. I'm a now broke college student so i'd like to spend as little $$$$ as possible
*PS I should also note the DVD drive is working fine, it reads the disk, the disk is brand new, it plays DVD's fine and has never had any issues in the years i've used it for similar tasks*
sorry for the long drawn out post, I just wanted to include as much as possible from what I've seen other people have issues with

BrettGoudy wrote:
...Is there any way I can install a partition that runs snow leopard on my early 2011 MB pro with what I have (new SSD, New RAM, Current version Lion running, no external drive, lack of original snow leopard disks [I lost them ] and the general 10.6.3 snow leopard boot disks)...
As the last post suggests, call Apple and order a replacement original disc for about $17. They will ask you the model and serial numbers.
Your retail version of Snow Leopard OS 10.6.3 will not work on that Mac as it requires a minimum of OS X 10.6.7 to boot and operate.
Another alternative is to again borrow another Mac to install your retail Snow Leopard into an external HD or partition, upgrade it to 10.6.8 and then clone it back to a partition on your MBP.

How do I make a boot disk?

How do I make a boot disk in OSX 10.4 something and have some tools like Disk Warrior on it? I found one program at versiontracker that does this but it doesn't work in .4, oh well ...... or I can just wait for several days til my DiskWarrior CD comes in the mail ....... but who can be without their computer that long in today's day and age? yup, you guessed it, my powerbook won't start up and I've tried lots so far ...... hoping dw will do the trick.

http://www.macosg.com/group/viewtopic.php?t=13956
-Bmer
Mac Owners Support Group
Join Us @ MacOSG.com
iTunes: MacOSG Podcast
 An Apple User Group 
Disclaimer required by Apple Discussions Terms of Use: MacOSG - a non-profit Apple User Group - may receive some form of compensation, financial or otherwise, from my recommendation or link.

How to make boot disk for MacBook Pro with Mavericks pre-installed

Hi -
I recently bought a new 15" MacBook Pro with Retina Display, which came pre-installed with Mavericks (10.9.0). I want to make a bootable USB disk of the system software, and have successfly used DiskMaker X (formerly Lion DiskMaker) to make the USB boot disks for Lion and Mountain Lion. In those cases, however, I was running earlier versions of the OSX, and downloaded the new OSX version -- Lion and Mountain Lion -- from the App Store in order to make to make the disk. In this case, however, Mavericks was pre-installed, and I was unable to download it from the App Store (an alert said that it couldn't be installed on this computer... presumably because it was already installed). I would apprecite any suggestions as to how I can create the boot disk without the ability to download Mavericks. Thanks very much for any help anyone can provide.
Shelly

Open App Store and locate the full installer download file (5.29 GBs) for 10.9.1. Download to your computer.
Make Your Own Mavericks, Mountain/Lion Installer
After downloading the installer you must first save the Install Mac OS X application. After the installer downloads DO NOT click on the Install button. Go to your Applications folder and make a copy of the installer. Move the copy into your Downloads folder. Now you can click on the Install button. You must do this because the installer deletes itself automatically when it finishes installing.
2. Get a USB flash drive that is at least 8 GBs. Prep this flash drive as follows:
Open Disk Utility in your Utilities folder.
After DU loads select your flash drive (this is the entry with the mfgr.'s ID and size) from the leftside list. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
Select the volume you just created (this is the sub-entry under the drive entry) from the left side list.
Click on the Erase tab in the DU main window.
Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
Click on the Erase button. The format process can take up to an hour depending upon the flash drive size.
3. Use DiskMaker X to put your installer clone onto the USB flash drive.
Make your own Mavericks flash drive installer using the Mavericks tool:
You can also create a Mavericks flash drive installer via the Terminal. Mavericks has its own built-in installer maker you use via the Terminal:
You will need a freshly partitioned and formatted USB flash drive with at least 8GBs. Leave the name of the flash drive at the system default, "Untitled." Do not change this name. Open the Terminal in the Utilities folder. Copy this command line after the prompt in the Terminal's window:
sudo /Applications/Install\ OS\ X\ Mavericks.app/Contents/Resources/createinstallmedia --volume /Volumes/Untitled --applicationpath /Applications/Install\ OS\ X\ Mavericks.app --nointeraction
Press RETURN. Enter your admin password when prompted. It will not be echoed to the screen so be careful to enter it correctly. Press RETURN, again.
Wait for the process to complete which will take quite some time.

How I make a boot disk

Hello.
I'm an absolut Linux beginner and I tried to install archlinux on an external HDD, because my internal windows drives are dynamic logical Volumes and this doesn't work with Linux.
After the installation from the CD I noticed that I cannopt boot from USB HDD because of the BIOS.
How I make a boot disk (floppy) now ? The wiki guide doesn't help because if I boot from the installation CD I don't have the command fdformat and the command pacman - S grub works neither.
Can you help?
Best Regards
BX-8017
Excuse by bad language please, I'm not english!

Ok,
I found a grub boot disk on the net, it was a super grub boot disk. I deleted nearly all files and just copied my files from /boot/grub in the grub directory of the floppy disk. I used the windows tool "explore2fs" to get acces to my boot partition with the grub directory.
Her is my menu.lst:
# (0) Arch Linux
title Arch Linux
root (hd2,0)
kernel /vmlinuz26 root=/dev/sdc1 ro vga=773
initrd /kernel26.img
# (1) Arch Linux
title Arch Linux Fallback
root (hd2,0)
kernel /vmlinuz26 root=/dev/sdc1 ro vga=773
initrd /kernel26-fallback.img
# (1) Windows
title Windows XP
rootnoverify (hd0,0)
makeactive
chainloader +1
It doesn't work, because the hd 2,0 is not found from grub. (Selected disk does not exist)
It seams that grub is not recognizing my usb hdd at start up ?!?! but this cannot be, because during the installation process it is.
Many Thanks
BX-8017
PS The possibility to boot Arch with the Windows Bootmanager is interesting. Maybe we can discuss this later.....
Last edited by BX-8017 (2007-07-18 15:36:57)

Can I Make a Leopard Boot disk with my Free Agent Desk 1.5TB External Hard Drive?

Can I Make a Leopard Boot disk with my Free Agent Desk 1.5TB External Hard Drive? Using my Power Mac G5 Dual 2.0Gig original computer?

Only if it is a FireWire interface. The G5's won't boot to a USB 2.0 drive.

Help me make a boot disk

hi, i have tried all sorts of ways to make a boot disk with a working Disk warrior, i have tried bootcd( but doesnot work on 10.4) i have tried CLoneX, but it wont load Disk warrior, i have even created a disk image of my mac os X up grade disk and then put diskm warrior on it, (just drag and drop form the orginal disk image) , but itg wont load, at the moment, i am tring to use my mac os X install disk.....any tips would be great
i am trying to repair my catalog file , whihc apparently has an illegal name..... alos ii need to fix my 250gb hard drive that crashed, and now my computer wont even reconize,,,,,,,now, i have at my disposale aa 10gb hard drive and a 20 gib drive, i have installeed mac os x on the 10 gb, but it wont boot form it ( it is in a fire wire enclousre)...... my other 20 gb is crashed, and i cant mount it, in order to format it....... HElp plz
all3 haard drives are western digital,, and the enclousre is a A-Power.....here is a link to some info on the enclouure..... http://www.geeks.com/details.asp?invtid=AP35-C&cat=CAS
Help me plz
also any tools besides disk warrior would be a great help, because when the device is connected and i try to run diskwarrior, it just freezzes......

Hello,
I am following the video Alsoft recommends in order to create an emergency disk.
http://www.macworld.com/quicktime/webbungalow12-01.mov
It is very helpful. I only purchased Disk Warrior a few days ago.
I am trying to install from the download I received. My CD will arrive in the mail at some point
I can only get so far. As it is installing to the emergency disk it stops with an error message:
An error occurred while trying to complete the installation. Installation was canceled, leaving your dis untouched.
Any idea what am I doing wrong?????
Thank you

Make a USB boot disk to restore OS AND files

I use Time Machine faithfully. I've installed OS 10.6 on a thumb drive for emergencies to restore files etc. when i've errantly thrown them away, and always thought I could somehow use it to restore my system in the event of a really big problem (never had to really test it out for real...until last night!)
I discovered that just having a boot disk isn't enough. I still needed to boot from the original CD, go to "Utilities", then "Restore from Backup". So much for all my planning.
Isn't there a way to include that essential feature on my USB boot disk?

All you need is a external powered USB drive and free Carbon Copy Cloner.
http://www.bombich.com/
You can hold option and boot from the clone, make a backup or reverse clone when you want, total access to the clone from another Mac.
You don't need TimeGizmo or a USB thumb drive or cd's that scratch. Your not a newbie that deletes files by accident.
And if you are there is free software for that here:
http://www.cleverfiles.com/pro.html
(no comp ever)

How do I make a boot disk for my new iMac?

How do I make a boot disk for my new iMac?

Make Your Own Mavericks, Mountain/Lion Installer
After downloading the installer you must first save the Install Mac OS X application. After the installer downloads DO NOT click on the Install button. Go to your Applications folder and make a copy of the installer. Move the copy into your Downloads folder. Now you can click on the Install button. You must do this because the installer deletes itself automatically when it finishes installing.
   2. Get a USB flash drive that is at least 8 GBs. Prep this flash drive as follows:
Open Disk Utility in your Utilities folder.
After DU loads select your flash drive (this is the entry with the mfgr.'s ID and size) from the leftside list. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID then click on the OK button. Click on the Partition button and wait until the process has completed.
Select the volume you just created (this is the sub-entry under the drive entry) from the left side list.
Click on the Erase tab in the DU main window.
Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
Click on the Erase button. The format process can take up to an hour depending upon the flash drive size.
Use DiskMaker X to put your installer clone onto the USB flash drive.
Make your own Mavericks flash drive installer using the Mavericks tool:
You can also create a Mavericks flash drive installer via the Terminal. Mavericks has its own built-in installer maker you use via the Terminal:
You will need a freshly partitioned and formatted USB flash drive with at least 8GBs. Leave the name of the flash drive at the system default, "Untitled." Do not change this name. Open the Terminal in the Utilities folder. Copy this entire command line after the prompt in the Terminal's window:
     sudo /Applications/Install\ OS\ X\ Mavericks.app/Contents/Resources/createinstallmedia --volume
     /Volumes/Untitled --applicationpath /Applications/Install\ OS\ X\ Mavericks.app --nointeraction
Press RETURN. Enter your admin password when prompted. It will not be echoed to the screen so be careful to enter it correctly. Press RETURN, again. Wait for the process to complete which will take quite some time.

How to make a boot disk for new iMac?

I just purchased a new iMac equipped with a bare bones 1TB SATA hard drive. I want to replace that disk with a 1TB SSD from Crucial (less than 1/2 of the cost of purchasing the iMac with the SSD). I have a Time machine backup of the iMac on a Time Machine/Airport device; how do I make a boot disk that can get the OS up and running, and able to restore the backup from the Time Machine?
Thanks,
Tony Darst
Baton Rouge, LA

tdarst wrote:
I had not given the warranty issue any prior thought; thanks for pointing that out. Is there a way around the warranty issue; such as a "factory authorized" way to install it, that is feasible?
Thanks for the quick response...
TD
You can take it an AASP to have the install done however you probably would be better off returning the machine (assuming it was bought directly from Apple and is less than 14 days old) and buy the configuration you want. Even if an AASP does install the SSD there is no guarantee Apple will honor the warranty, it's 100% at their discretion.

White Screen at Boot When Attempting to Access Recovery or Select a Boot Disk

Introduction
I want to share a solution for a problem I encountered that Apple technical support was unaware of (they said they would create a new kdoc when I called them to share my problem and its solution) and for which I could find no documentation online.
First, this is really a tip rather than a question, but I did leave it marked as a question in case anyone wants to earn some points by responding with a different solution to the problem I am about to describe. Additionally, I do not have a enough points to post a "Tip" so I am just starting a discussion instead.
Next, when I encountered the problem I am about to describe, I had not yet enabled a firmware password.
Finally, a massive "Thank you!" to the Great Pondini (James Pond - http://pondini.org) for helping me learn so much more interesting stuff about various OS X features and functionality (all for no charge) over the years.
Now on to why I have started this discussion...
The Problem
I recently purchased a new MacBook Pro (Core i7, SSD, etc.). After working with Setup Assistant to transfer everything from the most recent Time Machine backup of the older MBP I was replacing, applying all OS updates, and then enabling FileVault 2 and letting the requisite disk encryption process complete, I decided to I would go ahead and just proactively repair any permissions and ACLs for my user directory just in case any repair was necessary.
However, after shutting down my MBP, waiting, and then starting it up with Cmd-R being pressed while turning the MBP on, nothing would happen - I would just have a white screen with no Apple logo, no EFI login, no Recovery Console, nothing (and I waited for a very long time for something to show up). My only option was to do what I really do not like doing and that was to just power my new MBP down.
So, I tried again, this time holding down Opt while turning my computer on so as to select a disk at boot. The same problem returned.
Just to check, I once again started up while holding down the Shift key to attempt a Safe Boot. No dice.
Prior to trying all of this I made sure that I did have the Apple Recovery Partition in addition to my user partion and the EFI partition, so I did not understand why this would be happening. Why could I not boot into Recovery? Why could I not select a boot disk? And, why could I not go into Safe Boot?
To be safe, I started up and logged into my MBP as I normally would, then set my startup disk to be my Recovery USB for OS X 10.8, restarted, and verified all three partitions (and, since I had my Time Machine disk connected all three times I forced the computer to power off, I verified it as well). I then set my startup disk back to my SSD, and logged in and got online to see if anyone else had experienced this issue. After making sure I was not being crazy and using key combinations that were somehow made irrelevant, I shut my MBP down and walked away for a few minutes.
The Solution
So what solved my problem? A good 'ol reset of the NVRAM (aka/fka PRAM). If you are not familiar with how to reset the NVRAM:
Power off your Mac and go do something else for 30 seconds to a minute.
Press and hold down the Opt, Cmd, P and R buttons, and then press the power button. I have big hands and this is a one person operation for me. If you are not so "lucky", find someone to press the power button as you hold those four buttons down.
Continue holding those four buttons down through the first startup chime and then release all four of them only after the second startup chime is sounded.
So, for some reason, I had to reset the NVRAM on a brand new MBP that had been started up only once and restarted only once when I enabled FV2. Maybe something cached needed to be cleared out following the FV2 process, or maybe something funky was carried over after it was setup in the factory and shipped direct to me from China.
The moral of the story is: If you have strage issues during the startup of your Mac, just reset the NVRAM and try again. This has worked for a number of strange issues on various Macs for me in the past and proved to be useful once again on a brand new MBP that I never would have thought needed its NVRAM reset so soon into its lifecycle.
Special Note
There are two processes I always complete and recommend to others following a major software update (e.g. upgrading to a new version of OS X) and when I restore or otherwise transfer the most recent Time Machine backup to my current Mac or to a new one.
First, following a major or massive software update, go into Disk Utility, select your system and data drive(s), and then just click on "Repair Permissions" (Choosing "Verify Pemissions" will result in having to then click "Repair Permissions" if any permissions need to be repaired, so remove one click from the process).
Second, after transferring from a Time Machine backup, I like to make sure that my user directory permissions are good to go before any time is allowed for problems with those permissions to set in. If you are not familiar with the user directory permissions and ACL repair process (this process is not the same as the "Repair Permission" functionality in Disk Utility), here is how to do it:
Shutdown your Mac and wait about 30 seconds.
Press and hold down Cmd-R and then power on your Mac. Once the Apple logo with the spinning wheel shows up, release those two keys.
From within the Recovery Console, open a new Terminal session via the "Utilities" menu.
Invoke the following command (all one word, lowercase): resetpassword
In the "Reset Password" application that opens, select the disk that your user home directory is on, and then click the "Reset" button at the bottom underneath the "Reset Home Folder Permissions and ACLs" heading and wait for the process to finish. Any messages displayed can typically be safely ignored. If you want to be sure, search for information regarding any messages that you do not like.
Restart your MBP and enjoy using it.
(Note that if you have FV2 enabled, you will need your FV2 Recovery Key to actually reset your password. This is one of many reasons that I enable FV2 - anyone can startup a Mac and go into the Recovery Partition if it exists and reset a password, but having to also enter the FV2 Recovery Key adds a nice extra layer of protection. In addition to that, setting a Firmware Password makes it nearly impossible to start up from any disk other that that which is currrenlty installed in your Mac without knowing the Firmware Password - another security bonus. If someone gets ahold of your Mac, and you have FV2 enabled and an appropriately complex Firmware Password set, then them using your Mac as their own becomes a decently difficult process. It's by no means perfect computer security, but it makes it more challenging for someone to steal and use your Mac.)
If anyone has any other tips to share or additional solutions to problem I described, please discuss and share.

Which OS X is installed on your Mac ?
Troubleshooting advice can depend on that information.

I've downloaded Lion. I have a boot disk. Can I use it to install on another machine?

I downloaded Lion from the Mac App store and it's working 100%. Love it.
After downloading and before installing, I copied the installESD.dmg (I think that's the correct filename) to a DVD (as per all the instructions out there to create a boot disc). I did NOT copy the entire "Install Lion App" to the DVD.
My question is: if a friend buys lion from the app and then cancels the download, can he use my boot disk to install lion as an upgrade? The reason I'm asking is that his Internet connection is rubbish and he can't download it. Presumably if I copy the dmg file to his hard disk I can run it that way?

Actually, you can burn a DVD or USB (8GB) thumb drive and let him boot and install from it. Or, you can actually run the InstallESD.dmg file from his machine. I've done both and Lion installs.
Personally, I would burn a DVD or thumb drive so you always have it.
Burn the InstallESD.dmg to a bootable DVD.
Launch Disk Utility and click the Burn button
Select the InstallESD.dmg file from your desktop as the image to burn. Insert a blank DVD and wait for the the image to be burned.
Burn the InstallESD.dmg to a bootable USB thumb drive.
Open Disk Utility and drag the InstallESD.dmg file to the left side pane. Go to the Partition tab ad select 1 Partition from the drop down menu. Choose Mac OS Extended (Journaled) on the left. Click the Options button under the partition table and choose GUID Partition Table. You will need this to make the drive bootable on a Mac. Hit the Apply button when ready to format the drive (it will erase everything on the drive).
Click on the Restore tab and drag the InstallESD.dmg file to the Source. Drag the USB partition to the Destination. Hit the Restore button and it will create the bootable USB drive with the OS X Lion installer

"No Bootable Device -- insert a boot disk and press any key" Error Message.

Last month I just got a HP netbook (HP Mini 110-3100) and when I got it from the box, the error message; "No bootable device -- insert a boot disk and press any key" appeared. But then I managed to boot up the netbook normally. After that, I can use the netbook normally but the error message keeps appeared and becomes more frequent and now I even cannot turn on the netbook.
Is it a hard disk failure?
p/s: yesterday accidentally I can turn on the netbook without any problems. Did a lot of Hard Disk Maintenance by some softwares downloaded from the internet. But now already cannot turn on.
p/s/s: i have no cd/dvd drive, and also no 8GB usb drive.
p/s/s/s: what should i bring if i want to send the netbook to the HP centre? just bring the netbook?

I would suggest try and reseat the hard drive and check...If you still have the issue, than take it to the service center...And you will need to take only netbook to Service center...
Although I am an HP employee, I am speaking for myself and not for HP.
Make it easier for other people to find solutions, by marking my answer with 'Accept as Solution', if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

To make 10.4.11 boot disk

Similar Messages

Maybe you are looking for