Too many error codes: can't update!

Well, I wanted to update my iPod nano(2nd gen), so I plugged it in, and it says it is updating, and after a while, it says "iPod cannot be updated; an error occured (-50). It then continues to update again, rendering me unable to do anything, then a window pops up saying
"The disk could not be read from or written to."
So I go into my Nano's settings and click the "enable disk use" box. It then says it is updating and givse me the same error code as the one I first mentioned. This continues in a loop, and what's worse is that I accidentaly deleted all my songs the previous night! Help!
an Acer with Windows XP Windows XP

See this troubleshooting article.
Disk cannot be read from or written to error syncing iPod in iTunes.

Similar Messages

How to fix your iPhone 4 after you have been disabled from trying too many pass codes after the update? I haven't used a passcode in so long I can't remember it.

I downloaded the new IOS 7 and it asked for a pass code to unlock it when it finished, however, I haven't used a pass code in so long, I don't remember what it is! I have tried all I have ever used and still no luck. Now my phone is disabled and I can't use my new operating system! Very disappointed!

Try to connect to a computer with your paired iphone, the run iTunes and Run Restore iPhone

Too many error records - update terminated

Hello !!!
Please help me with resolutions/reasons for the below errors.
While loading data following errors are coming up & also the number of erroneous records when seen through PSA is quiet large (>2000). We neither want to delete the data nor to edit it, as prior to upgrade this InfoPackage used to work perfectly fine
(Please note that system is recently upgraded from BI 3.x to BI 7.0).
Too many error records - update terminated
Message no. RSM2706
Diagnosis
More than 1001 records have been flagged as incorrect. There is probably a system error.
System Response
For performance reasons, the system terminates the update and additional checks.
Thanks,
Shantanu.

Hi,
I think you are facing an invalid character issue.
This issue can be resolved by correcting the error records in PSA and updating it into the target. For that the first step should be to identify if all the records are there in PSA. You can find out this from checking the Details tab in RSMO, Job log , PSA > sorting records based on status,etc. Once its confirmed force the request to red and delete the particular request from the target cube. Then go to PSA and edit the incorrect records (correcting or blanking out the invalid entries for particular field InfoObject for the incorrect record) and save it. Once all the incorrect records are edited go to RSA1>PSA find the particular request and update to target manually (right click on PSA request > Start update immediately).
I will add the step by step procedure to edit PSA data and update into target (request based).
Identifying incorrect records.
System wont show all the incorrect records at the first time itself. You need to search the PSA table manually to find all the incorrect records.
1. First see RSMO > Details > Expand upate rules / processing tabs and you will find some of the error records.
2. Then you can go to PSA and filter using the status of records. Filter all the red requests. This may also wont show the entire incorrect records.
3. Then you can go to PSA and filter using the incorrect records based on the particular field.
4. If this also doesnt work out go to PSA and sort (not filter) the records based on the particular field with incorrect values and it will show all the records. Note down the record numbers and then edit them one by one.
If you want to confirm find the PSA table and search manually."
Steps to resolve this
1. Force the request to red in RSMO > Status tab.
2. Delete the request from target.
3. Come to RSMO > top right you can see PSA maintenace button > click and go to PSA .
4.Edit the record
5. Save PSA data.
6. Got to RSA15 > Search by request name > Right click > update the request from PSA to target.
This should solve your problem for now.
As a long term you can apply some user exit in source system side or change your update rules to ensure that this field is getting blanked out before getting loaded in cube or add that particular achr to permitted character list in BW (Run TCODE RSKC
Input the <character> and execute the program) This will add <character> to the allowed characters list.
OR
RSKC --> type ALL_CAPITAL --> F8 (Execute)
OR
Run the report RS_ERRORLOG_EXAMPLE,By this report you can display all incorrected records of the data & you can also find whether the error occured in PSA or in TRANSFER RULES.
OR
Go to SE38 and execute the program RSKC_ALLOWED_CHAR_MAINTAIN.
Refer
/people/sap.user72/blog/2006/07/23/invalid-characters-in-sap-bw-3x-myths-and-reality-part-2
/people/sap.user72/blog/2006/07/08/invalid-characters-in-sap-bw-3x-myths-and-reality-part-1
/people/aaron.wang3/blog/2007/09/03/steps-of-including-one-special-characters-into-permitted-ones-in-bi
http://help.sap.com/saphelp_nw04/helpdata/en/64/e90da7a60f11d2a97100a0c9449261/frameset.htm
Thanks,
JituK

0ASSET_AFAB Errors - too many error records update terminated

too many error records update terminated -
It says too many error records as I have set an allowance of 10000 erroneous records in an attempt to get the transactional loads to work as they are dependant on this extracting successfully. This brought through over 10000 erroneous records.
Regards
Helpful answeres are surely rewarded

Hi Voodi / Sorabh,
Message Text: Too many error records - update Terminated
ID: RSM2
NO: 706
Message Text: Error in the update
ID: RSAR
ID: 119
Thanks in advance.

Error code 800f0900 windows update

request: can someone please help me with this windows update issue? thank you<o:p></o:p>
error code 800f0900 windows update <o:p></o:p>
have: windows 7 ultimate<o:p></o:p>
tried:<o:p></o:p>
MicrosoftFixit.wu.LB.193479011044059.1.1.Run<o:p></o:p>
Windows6.1-KB947821-v34-x64<o:p></o:p>
WindowsUpdateDiagnostic<o:p></o:p>
Windows Update troubleshooter <o:p></o:p>

Unfortunately your post is off topic here, in the TechNet Site Feedback forum, because it is not Feedback about the TechNet Website or Subscription. This is only one forum among the many
that are on the TechNet Discussion Forums, and given your post, you likely chose the wrong forum. This is a standard response I’ve written up in advance to help many people (thousands, really.) who post their question in this forum in error, but please
don’t ignore it. The links I share below I’ve collected to help you get right where you need to go with your issue.
For technical issues with Microsoft products that you would run into as an
end user of those products, one great source of info and help is
http://answers.microsoft.com, which has sections for Windows, Hotmail, Office, IE, and other products. Office related forums are also here:
http://office.microsoft.com/en-us/support/contact-us-FX103894077.aspx
For Technical issues with Microsoft products that you might have as an
IT professional (like technical installation issues, or other IT issues), you should head to the TechNet Discussion forums at
http://social.technet.microsoft.com/forums/en-us, and search for your product name.
For issues with products you might have as a Developer (like how to talk to APIs, what version of software do what, or other developer issues), you should head to the MSDN discussion forums at
http://social.msdn.microsoft.com/forums/en-us, and search for your product or issue.
If you’re asking a question particularly about one of the Microsoft Dynamics products, a great place to start is here:
http://community.dynamics.com/
If you really think your issue is related to the subscription or the TechNet Website, and I screwed up, I apologize! Please repost your question to the discussion forum and include much more
detail about your problem, that could include screenshots of the issue (do not include subscription information or product keys in your screenshots!), and/or links to the problem you’re seeing.
If you really had no idea where to post this question but you still posted it here, you still shouldn’t have because we have a forum just for you! It’s called the Where is the forum for…?
forum and it’s here: http://social.msdn.microsoft.com/forums/en-us/whatforum/
Moving to off topic.
Thanks
MSDN and TechNet Subscriptions Support
Did Microsoft call you out of the blue about your computer?
No, they didn't.

How you restore your security pass code if you have disabled your iPod, due to too many pass code attempts

How you restore your security pass code if you have disabled your iPod, due to too many pass code attempts?

If You Are Locked Out Or Have Forgotten Your Passcode
iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
iOS- Understanding passcodes
     If you have forgotten your Restrictions code, then follow the instructions
     below but DO NOT restore any previous backup. If you do then you will
     simply be restoring the old Restrictions code you have forgotten. This
     same warning applies if you need to restore a clean system.
A Complete Guide to Restore or Recover Your iDevice (if You Forget Your Passcode)
If you need to restore your device or ff you cannot remember the passcode, then you will need to restore your device using the computer with which you last synced it. This allows you to reset your passcode and re-sync the data from the device (or restore from a backup). If you restore on a different computer that was never synced with the device, you will be able to unlock the device for use and remove the passcode, but your data will not be present. Refer to Updating and restoring iPhone, iPad and iPod touch software.
Try restoring the iOS device if backing up and erasing all content and settings doesn't resolve the issue. Using iTunes to restore iOS devices is part of standard isolation troubleshooting. Restoring your device will delete all data and content, including songs, videos, contacts, photos, and calendar information, and will restore all settings to their factory condition.
Before restoring your iOS device, Apple recommends that you either sync with iTunes to transfer any purchases you have made, or back up new data (data acquired after your last sync). If you have movie rentals on the device, see iTunes Store movie rental usage rights in the United States before restoring.
Follow these steps to restore your device:
     1. Verify that you are using the latest version of iTunes before attempting to update.
     2. Connect your device to your computer.
     3. Select your iPhone, iPad, or iPod touch when it appears in iTunes under Devices.
     4. Select the Summary tab.
     5. Select the Restore option.
     6. When prompted to back up your settings before restoring, select the Back Up
         option (see in the image below). If you have just backed up the device, it is not
         necessary to create another.
     7. Select the Restore option when iTunes prompts you (as long as you've backed up,
         you should not have to worry about restoring your iOS device).
     8. When the restore process has completed, the device restarts and displays the Apple
         logo while starting up:
           After a restore, the iOS device displays the "Connect to iTunes" screen. For updating
          to iOS 5 or later, follow the steps in the iOS Setup Assistant. For earlier versions of
          iOS, keep your device connected until the "Connect to iTunes" screen goes away or
          you see "iPhone is activated."
     9. The final step is to restore your device from a previous backup.
If you can not restore your device then you will need to go to recovery mode.
Placing your device into recovery mode:
Follow these steps to place your iOS device into recovery mode. If your iOS device is already in recovery mode, you can proceed immediately to step 6.
     1. Disconnect the USB cable from the iPhone, iPad, or iPod touch, but leave the other end
         of the cable connected to your computer's USB port.
     2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the
         red slider appears, then slide the slider. Wait for the device to turn off.
          If you cannot turn off the device using the slider, press and hold the Sleep/Wake
          and Home buttons at the same time. When the device turns off, release the Sleep/Wake
          and Home buttons.
     3. While pressing and holding the Home button, reconnect the USB cable to the device.
         The device should turn on. Note: If you see the screen pictured below, let the device
         charge for at least ten minutes to ensure that the battery has some charge, and then
         start with step 2 again.
     4. Continue holding the Home button until you see the "Connect to iTunes" screen.
         When this screen appears you can release the Home button.
     5. If necessary, open iTunes. You should see the following "recovery mode" alert:
     6. Use iTunes to restore the device.
If you don't see the "Connect to iTunes" screen, try these steps again. If you see the "Connect to iTunes" screen but the device does not appear in iTunes, see this article and its related links.
Additional Information:
Note: When using recovery mode, you can only restore the device. All user content on the device will be erased, but if you had previously synced with iTunes on this computer, you can restore from a previous backup. See this article for more information.

Aborting index build. Too many errors with finding and copying files ...

Hi dears,
I'm using UCM 11g.
I'm trying to start the automatic update cycle. When i start it, it gives me an error message just like :
Indexing aborted at :<time>. Aborting index build. Too many errors with finding and copying files to the appropriate place.+
Can anybody help me about this problem?
Helps will be appreciated.
Erdo
Edited by: erdo on 28.Mar.2013 11:11

Read this: error in Collection Rebuild Cycle
and maybe also UCM Indexer - Collection Rebuild Cycle errorring out

CJV4: Termination: Too many errors (Message no. CJ280)

Hi experts
While attempting transfer of Modified simulation version to Operative in transaction code CJV4, the following error experienced:
Error u201CTermination: Too many errors (more than 10% of methods)
Message no. CJ280u201D
Request please suggest solution.
Also suggest any other way to transfer simulation version to operative project (To update the operative project with selected simulation version).
warm regards
ramSiva

Hi experts
While attempting transfer of Modified simulation version to Operative in transaction code CJV4, the following error experienced:
Error u201CTermination: Too many errors (more than 10% of methods)
Message no. CJ280u201D
Request please suggest solution.
Also suggest any other way to transfer simulation version to operative project (To update the operative project with selected simulation version).
warm regards
ramSiva

Update_prebinding: too many errors (101)

thought my console was not working but then I realised that I had just reloaded the OS and there were no widgets in the console. so that works, but in the process I found this thread on CNET -- says;
Update prebinding Many cases of application launch-failure can be resolved easily by simply updating prebinding, via the following steps:
Log in as an administrator
Open the Terminal (located in Applications/Utilities)
Type: sudo update_prebinding -root / -force and press Return.
When prompted for a password, enter your admin password, and press Return again. The process may take a few minutes, and you may see various messages flash by. The process is complete when the Terminal returns to a normal prompt.
Type exit and press Return.
Check for the capability to launch the problematic application.
so I did that and it said;
update_prebinding: too many errors (101)
update_prebinding: error: terminating
... why would it be "too many errors" and how can I fix that?

Hi, Prebinding isn't needed any more...
https://discussions.apple.com/thread/1808611?start=0&tstart=0
After Safari 3.2 no need...
http://www.xlr8yourmac.com/archives/nov08/111408.html

Error code 805a0193 when updating apps and install...

Up until Sunday the 12th of August 2012 I have been able to install and update my apps with no fuss. When I tried to install an app on Sunday I got an the error code mentioned above whether through wifi or 3g (for both wifi and 3g my carrier is CELL C) I get the same error message. I have tried to restore my phone software to previous software prior to recent update and even there I get an error code 801812E0. I also tried resetting my phone to factory settings through the phone and this didn't help.
I'm now stuck and I posted the same message on here http://answers.microsoft.com/en-us/winphone/forum/wp7-wpapps/error-code-805a0193-when-updating-apps-... I have not received an answer.
The solutions posted on the site for a similar error relate to a DNS issue with wifi since I am using a cellc 3g card connected to a Sitecom wl-326 router and my Carrier is Cell C for my Lumia 800 i suspect it is an issue with Cell C our the current OS update.
Please Assist
Country: South Africa
Carrier: Cell C
Phone: Lumia 800 phone
OS version: 7.10.8773.98
Firmware version: 1750.0805.8773.12220
Hardware revision number: 112.1402.2.4
Zune Version: 4.8.2345.0

I'm experiencing the same problem on my Lumia 800 (as well as my girlfriend on her Lumia 710). The workaround is to set your router to use Google's DNS settings (8.8.8.8 and 8.8.4.4), further details here: http://answers.microsoft.com/en-us/winphone/forum/wp7-wpapps/marketplace-download-error-805a0193-ove...
I've tried it and it works but something still needs to be done about the problem itself.
I doubt there is anything Nokia can do about this sadly....

About ORA-00600 [kdiss_pin_hdr: too many] error

I meet a 'ORA-00600: ... parameter: [kdiss_pin_hdr: too many],[],[],[],[],[],[],[]' error when executing:
set transaction use rollback segment rbs_large_01;
select
CUST_NO||','||
TEL_NO||','||
ADDRESS||','||
ADDR_CODE_PREF||','||
ADDR_CODE_CITY||','||
ADDR_CODE_ZONE||','
from
CUSTOMER
where
     ADDR_CODE_ZONE = '000';
My system:
Oracle9i Enterprise Edition Release 9.0.1.2.0 - Production
With the Partitioning option
System name:     SunOS
Release:     5.8
Version:     Generic_108528-21
Machine:     sun4u
The sql should output about 70,000 rows, but it's stopped with the ora-00600 error after output 40,000 rows.
The table has 10,000,000 rows
rbs_large_01 is 512M - 2G
tempory tablespace is 2G
What's the error mean?
How can I resolve or avoid it?

Hi
i found in bug database:
bug 1827660 which is fixed in the 9.0.1.3 patchset
so, i mentioned use the latest patchset
lajos

Error code 50 when updating desktop

I received error code 50 when updating the creative cloud dekstop. It tells me to contact customer support. how do i do that?

Creative Cloud chat support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html

I want to restore my ipod 4g to ios 6.1.2 but it said error code 3194 i updated itunes and i checked my host file and it won't work Thank you for choosing the Apple Store. If you have any additional questions, please chat us again. You are currently not i

i want to restore my ipod 4g to ios 6.1.2 but it said error code 3194 i updated itunes and i checked my host file and it won't work and i am running 6.1.5 at the moment

That's because downgrading is not supported.

Does anybody know the error code 11 while updating to ios 4.3.3.? thx

does anybody know the error code 11 while updating to ios 4.3.3. on an ipad1? thx

but my hard drive is still lot of spaces...still keep on trying to update...

Error code after itunes update -42404

error code after itunes update -42404 cannot connect to ipad it is telling me to restore ipad, and cannot connect to store...
Message was edited by: CFC.Steve

I assume you updated itunes on your computer. PC or Mac?
Look at the posts in the More Like This area to the right side of this page.
Update and restore alert messages on iPhone, iPad, and iPod touch
http://www.buybuyla.com/tech/view/012953a0d412000e.shtml
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
 Cheers, Tom

Too many error codes: can't update!

Similar Messages

Maybe you are looking for