Too much power?

Hi (first post )
I have just got a new battery, and now a "funny" error occor.
When the battery runs dry of power, the computer shuts down, insted of going to the "standby mode" (don't know the word).
When I charge the battery and the computer is turned off, the computer will make 3 "bibs" when starting, and nothing is happening.
Then I turn of thte computer, and then it will start up.. Sometimes I have to "restart" it severel times, before it startes OS X.
When the computer is running, there are no problems at all!
I have done a SMU restart and a Hardware test, but nothing helps.
Here you can see the error: http://www.graphic-solution.dk/fejl.mpg
My theory: There is too much power on the battery, and by turning the mac on and off, it uses enough power, so the computer thinks it is all ok again.
Anyone who can help me?
(Sorry the bad spelling)
Message was edited by: Kasper Soerensen

Check this for help. Resolve startup issues and perform disk maintenance with Disk Utility and fsck
Have you done the battery update? About Battery Update 1.2.
I don't think this is a battery issue. What do you mean "Too much power?" I think I know what you mean but I would be surprised if that is the problem. Follow these directions, Determining Battery Cycle Count , and then post the following info back. Do this after the battery has reached a full charge and shows charged in the battery indicator. One tip, if you cut and paste the info like I did, be sure to remove any spaces from in front of the text or it will not display in the post.
Battery Information:
Battery Installed: Yes
First low level warning: No
Full Charge Capacity (mAh): 5495
Remaining Capacity (mAh): 5392
Amperage (mA): 0
Voltage (mV): 12472
Cycle Count: 12

Similar Messages

  • Error message (Because a USB device was drawing too much power)

    Hi Everyone,
    Bought recently a new macbook pro 13 inch with Retina display with 120 GB flash drive.
    Connected a non-apple CD drive to my macbook and after that started receiving this message: "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled."
    initially I was receiving this message after I switch on my macbook but now after every 30 seconds this message pops up although I never connected anything to my macbook through its USB ports.
    Will highly appreciate for your help on how to get rid of this problem.
    Regards
    Homayun

    Try resetting the SMC
    Shut down the computer.
    Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
    On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
    Release all the keys and the power button at the same time.
    Press the power button to turn on the computer. 
    Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.

  • I am trying to upload photos from my digital camera. Every time I try to plug it into my USB, the following error message comes up: "Because a usb device was drawing too much power from your computer, one or more of your USB devices have been disabled."

    I am trying to upload photos from my digital camera. Every time I try to plug it into my USB, the following error message comes up: "Because a usb device was drawing too much power from your computer, one or more of your USB devices have been disabled."
    I don't have anything else plugged into my MBP, so I am confused as to what's going on.  This problem has never happened before.  MBP is less than a year old - about 9 months old.  HELP

    Get a powered USB hub.
    https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

  • HT4106 How do I use a midi keyboard on GarageBand with my iPad? When I try it says the device cannot be used as it requires too much power.  However, I have given the midi it's own power source.

    How do I use a midi keyboard as an input device on garageband? Its an oxygen 61 board.  I'm using an iPad camera connection kit and a separate power source for the midi but each time it says it cannot use the midi as it requires too much power. 

    I have the same problem with my iPad and 61. Sometimes it says device not supported and sometimes it rants about power - any solutions anyone ?

  • MacBook pro 13" mid 2010 "USB drawing too much power" HELP

    Hi, my MacBook Pro keeps coming up with a window about 30 after start up saying "USB drawing too much power" and none if the USB ports work neither does the iSight camera (green light is constantly on) and the headphone jack won't work! I have tried re installing OSX but it hasn't worked! Apart from an SMC reset and a PRAM what else can I try? Absolutely nothing is plugged in not a single cable or keyboard or mouse just my MacBook on its own, is it definitely a software problem or am I going to have to get apple to repair the hardware because I do not have that much money to replace a logic board and get apple to replace it themselves. Thanks in advance!

    I hope it works for you ...

  • To upload photos from my pc onto my ipad using a usb stick. I bought a camera connector kit and tried placing the usb stick onto one of the white square adaptors, stuck it into the ipad2 and I got 'the device uses too much power'' message. Pls help.

    I am not very familiar with the ipad2. I wished to transfer some photos from my pc (not an apple pc but that is the only one I have) to my ipad2 as I thought it would be easier to cull them, edit, crop etc to create albums for our recent trip (the photos are already on the pc and no longer on the camera memory card). When I place the usb stick on the adaptor and stick it onto the Ipad2 I keep getting 'device uses too much power/ requires too much power' message. I read somewhere on the internet that a usb hub could be used to solve the issue but that did not work either. What am I doing wrong? Is there actually a way around this problem. If not why does apple sell this product for Ipad users at all?
    Thank you for any help/ solution you can offer.
    Regards

    I'd ask that on the iPad forum.
    https://discussions.apple.com/community/ipad

  • Can't print to HP Photosmart C5180. getting error mssg that says, "Because a USB device was drawing too much power from your computer, one or more of our USB devices have been disabled."  Never seen this before.  How do i fix this?

    can't print to HP Photosmart C5180. getting error mssg that says, "Because a USB device was drawing too much power from your computer, one or more of our USB devices have been disabled."  Never seen this before.  How do i fix this?

    Get a powered USB hub.
    https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

  • On my MacBook Pro with Retina Display, Why does the "USB Devices Disabled Unplug the device using too much power to re-enable USB devices" keep coming up after I unplugged the usb device?

    On my MacBook Pro with Retina Display 15", that I purchased a few weeks ago, started coming up with the following message on my desktop:
    "USB Devices Disabled Unplug the device using too much power to re-enable USB devices".
    I unplugged the device and the message still keeps coming up.
    This is what I have done so far to troubleshoot:
    I shut down the laptop. When booting up I pressed the command+option+p+r at the same time. It comes up with a menu to reinstall OSX, Get help online, Run Disk Utility, etc. I choose the disk utility and repair the disk and then restarted.
    The message keeps popping up and I can't seem to get rid of it. Why does the message keep popping up even though I don't have any devices hooked up to the laptop at all? Any help to reenable my usb ports and get rid of the messaage would be helpful.

    I talked to Apple Support and we at least stopped the bleeding, a little bit. These are the troubleshooting steps I did before I contacted Apple Support:
    1. Reinstalled OSX
    2. Restore the last known good Time Machine Backup.
    This did not fix my issue, so I called Apple Support and they told me this:
    1. Turn Power off.
    2. Wait 15 seconds.
    3. Plug in Magsafe adapter.
    4. Wait 15 seconds.
    5. Hold down the Shift+Option+Power Button for 20-30 seconds.
    6. Turn Power back on.
    Ok, this stopped the bleeding a little, but as soon as I plugged in a Apple USB Superdrive
    and a Apple Mini Displayport to VGA Adapter. This "USB Devices Disabled" pop-up pops up like every 30 minutes now. At least, it is not constantly popping up after I close it, so I guess it will do for the temporary. Going to contact Apple support, later, though to see what else can be done.

  • "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled." HELP!

    When I plug in my son's iPad I get this message "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled." I only have one charger for this iPad all my other chargers are for iPhone 4s. I have pluggerd it in different outlets around the house and the iPad will not charge. When I plugged it on my lap top to back it up it gave me the warning message. HELP!!

    I have the same problem on my Air. The message first came up while my iPhone was connected to it for some time. Since then, it pops up ALL THE TIME, whithout anything being connected to the USB port, at what appear to be random intervals that vary between about one hour and a few seconds. I have tried resetting the SMC and  the PRAM, but no results. A quick search revealed that thousands of users are facing this problem, but Apple has yet to provide a solution. Please help!

  • "Because a USB device was drawing too much power from your computer, one  or more of your USB devices have been disabled.

    Here is the total error message:
    "Because a USB devce was drawing too much power from your computer, one
    or more of your USB devices have been disabled.
    To prevent damaging your computer, the USB device drawing too much
    power has been disabled. Other devices may have also been disabled.
    When you disconnect the device drawing too much power, your other USB
    devices will be enabled again."
    Now in contrast to every other thread on this i get this error message eveytime i connect my soundcard (interface). Not when i start up the mac or anything, just when i connect the sound card. (the soundcard does not have its own power source but note that this has never happened before and i have had this soundcard for about a year!)
    It deactivates so i cannot use it.
    I have tried:
    Connecting the soundcard to my mothers mac -> it worked!
    Connecting an external harddrive to my mac -> it worked!
    so basically, i can't be the soundcard or the cable and it cannot be the mac USB port?
    I don't know what to do! i really need this to work! anyone got an idea??

    Hi, ryankeenanrk. 
    Thank you for visiting Apple Support Communities. 
    I would recommend trying the steps in both articles below and test the results. 
    OS X Mountain Lion: Reset your computer’s PRAM
    http://support.apple.com/kb/ph11243
    Intel-based Macs: Resetting the System Management Controller (SMC)
    http://support.apple.com/kb/HT3964
    Cheers,
    Jason H. 

  • "Because a USB device was drawing too much power from your computer..." error withOUT any USB device

    Hi,
    I am getting this error since recently when I am using my MBP:
    "Because a USB device was drawing too much power from your computer..."
    The 'funny' thing: there is no USB device attached to the computer (only power and monitor cables).
    Why is this happening and what could I do about it?
    Appreciate your ideas?

    It's probably an internal hardware fault, but you can try this:
    Intel-based Macs: Resetting the System Management Controller (SMC)

  • I am having a problem when I plug my iPod into my macbook. When I plug the cable into my mac I get the following message - "Because a USB device was drawing too much power from your computer, your USB device has been disabled." PLEASE HELP!

    I am having a problem when I plug my iPod into my macbook. When I plug the cable into my mac I get the following message - "Because a USB device was drawing too much power from your computer, your USB device has been disabled." CAN SOMEONE PLEASE HELP!

    The rest of the message in the pop up window says "To prevent damaging your computer, the USB device drawing too much power has been disabled. Other devices may have also been disabled. When you disconnect the device drawing too much power, your other USB devices will be enabled again."

  • New iMac 27"  and just plugged in a Apple USB superdrive and get message, "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled."  I am trying to load Office mac2011  what to do?

    I have a new iMac 27"  and just plugged in a Apple USB superdrive and get message, "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled."  I am trying to load Office mac2011  what to do?

    If you just bought the iMac and the Sjuperdrive take the superdrive back and get a refund. The by any other brand external DVD drive that connects by USB and try that. Most come with a Y USB cable to allow you to connect to 2 USB ports to supply enogh power to the drive IF Needed.
    Or take both back and get a refund on both, you have 14 days to return it no questions asked, and buy another iMac and some other brand external DVD drive.

  • I keep getting this message : Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled.

    I keep getting this mesage : Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled.
    I need to charge my phone but it's not letting me!! Please help!

    Solution may be found if you search in the "More Like This" section over in the right column and in the article - http://support.apple.com/kb/HT1151. 

  • HT1212 i get this message? "Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled."

    Because a USB device was drawing too much power from your computer, one or more of your USB devices have been disabled?
    What do I do?

    Not Charge
    - See:      
    iPod touch: Hardware troubleshooting
    - Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use. One symptom of a bad Lightning cable is the message you are getting.
    - Try another charging source
    - Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
    - Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar      

  • Device drawing too much power...?

    Am trying to charge my original iPhone and both the wall charger as well as computer (mac) do not seem to allow it to charge. When I plug into my computer, I get an error message that says:
    +Because a USB device was drawing too much power from your computer, one or more of your devices have been disabled. To prevent damaging your computer, the USB device drawing too much power may have also been disabled. When you disconnect the device drawing too much power, your other USB devices will be enabled again.+
    When I press the power button on the phone, I get the low battery icon on the screen (red bar showing it needs to be plugged into a power source).
    Not sure what is happening or what to do... Can anyone help?
    Thanks so much in advance.

    Try it with a new cable. The one you have might be damaged.

Maybe you are looking for

  • My Apple TV is not authorize to play rentals movies

    I rented a movie and when I try to play it on my apple TV 2 generation it shows the following mesage "your apple tv is not authorize to play this content". I try desathorizing it and authorizing it again but nothing happent. I have 3 new retals movie

  • Granting permanant read access

    I am developing a project that accesses the mobile's filesystem.. When i tested it on SE phones, it asks only the 1st time whether to allow the application to read user data.. However on nokia phones it constantly prompts this message each time my mi

  • Edit stereoscopic (3d) footage

    I'm trying to edit stereoscopic (3d) footage. I've seen some tutorials of Dave Helmly. I 'm using AVCHD 3D (.MTS) files. I'm expecting to see a Side-by-side image in the program monitor and  hope to see an actual 3D image on my 3D screen. But that do

  • Multiple malfunctions on my iPad mini

    My iPad mini has taken on a life of its own.  Apps open and close on their own, components of games either move on their own or lock and won't move at all, (i.e. jigsaw puzzle pieces in Magic Puzzle app spin and move in and out of puzzle area without

  • PLN PCK No in BAPI for service entry

    Hi, I am creating service entries via BAPI_ENTRYSHEET_CREATE for planned services. If I am using one PO line item then I am able to create service entries with proper PLN_PCK number and all. But if I use mutliple line items in PO(not sublines) then P