Top of key issues and charging issues

IPhone phone fall within the scope of change. Occasionally my phone off when I press the top button, but my situation is happening shopping mall in Istanbul Zorlu people can not change the phone are indicated. In addition, there are problems charging my Telia. What should I do?

Manuel Manev wrote:
Hi all, I have the following question - bought iphone 5c used a couple of days ago and have 2 issues so far - I have problems charging it - the battery would drain to 0% and will plug it in but will not charge, instead after a while the phone would turn on and stay 1% forever. Tried another charger and it charges but when it is off and charging it does not show the percentage bar on the screen. Secondly - when I turn it on, seems like there is weird light from the top and the screen seems to be no very responsive, when the phone is on.
Return the phone and get your money back,  Then purchase one from an authorized Apple dealer.
Could be you bought a lemon.

Similar Messages

  • My iphone 4s and ipad 2 both with 7.0.4 update will no longer connect to wifi but non-mac lap top has no issues

    my iphone 4s and ipad2 both with 7.0.4 update will no longer connect to wifi.
    About three days ago the ability to connect came and went and the connection never lasted more than 10-15 minutes; it has not been able to connect since last night. I do not think it's my wifi router as non-mac lap top has no issues. I have seem many similar questions posted.

    Reboot your router by removing all power from it for about 15 seconds. Also, if your router still has its default SSID (such as LINKSYS, DLINK, NETGEAR, etc) change the SSID to something unique. Note that all other devices on your network will have to be reconnected if you change the name, but if the name is still the default that is most likely your problem.
    If the SSID is not the default then the reboot should fix it.

  • Battery and charging issues

    I have a DROID X and have been having issues for the last few weeks with my phone staying charged and charging. I have had both my home and car chargers replaced. Everytime I charge my phone it says that it is charging bit the battery level does not improve. When I use my roommates charger it charges fine. Also the battery says I have a certain % of battery left then the next minute it goes down 10%andthat that happens whether it is charging or not. I don't know if a certain app could be causing this or if the phone is junk and I need to get it replaced. Its getting annoying that I have to charge it every night and can't be away from home because I wont have a charger. PLEASE HELP!!!

    trfalsone wrote:
    What app or type of app would you think could be causing the problem? I don't want to uninstall or factory reset my phone...if I wanted to do that I would just get a replacement phone. I do have an ATK on my phone...
    From your home screen, press menu>settings>about phone>battery use (unless Moto moved it).  This will give you a list of apps with a percentage of how much battery they have used.  Also an app called system panel in the market will help you to monitor what  is using system resources.  I would also personally recommend uninstalling ATK, though not all users would agree with me.  Maybe try turning off autokill and see if that helps.  I do agree with dirkbonn, though, that it sounds like a bad charger,

  • Accessory may not be supported error and charging issues with iphone4

    Hello,
    From past 2 weeks my Iphone4 (say A) keeps throwing error message "Accessory may not be supported" and doesn't charge the iphone after couple of minutes of charging. This happens when device is connected (for charging) to power outlet or to computer (USB port). I tried multiple original iphone/apple cables.  The same cable allows me to copy pictures from this device/Iphone4 when connected to computer via same USB cable, but the device/iphone4 does not charge. The same cable and charger charges my other Iphone4 (say B) perfectly fine. 
    I am really frustrated as to why this is happening.
    Searching on internet, it seems lot of people are facing this problem with their iphones and ipad devices and refer this issue as a software bug, which I also seem to think. How can it be the hardware issue when same charging port and same cables allows you to copy your pics etc. from your iphone device to your laptop but does not allow you to charge the same device? Same charging cable works with my other iphone4 and i tried multiple cables so I dont think it's a cable issue.
    Any help is appreciated. I was expecting apple products to be better in quality but lately I have seen this issues quite often.
    -RP

    Make sure you are using an Apple approved charger and cable.  The best would be the charger and cable that came with the iPhone in the original box.

  • IPad 3 Syncing and Charging Issue...

    Hi I just recently bought a new ipad (3rd gen) in a local apple store,,, an now I try to sync it on my PC via itunes and I noticed that in the batter indicator it says "Not Charging" even though I hooked it up on a USB 2.0 port,,, why is that? I have an iPhone 4s but everytime i connect it to my pC it automatically charge why is that my iPad is not charging????

    The quickest way (and really the only way) to charge your iPad is with the included 10W USB Power Adapter. iPad will also charge, although more slowly, when attached to a computer with a high-power USB port (many recent Mac computers) or with an iPhone Power Adapter (5W). When attached to a computer via a standard USB port (most PCs or older Mac computers) iPad will charge very slowly (but iPad indicates not charging). Make sure your computer is on while charging iPad via USB. If iPad is connected to a computer that’s turned off or is in sleep or standby mode, the iPad battery will continue to drain.
    Apple recommends that once a month you let the iPad fully discharge & then recharge to 100%.
    How to Calibrate Your Mac, iPhone, or iPad Battery
    http://www.macblend.com/how-to-calibrate-your-mac-iphone-or-ipad-battery/
    At this link http://www.tomshardware.com/reviews/galaxy-tab-android-tablet,3014-11.html , tests show that the iPad 2 battery (25 watt-hours) will charge to 90% in 3 hours 1 minute. It will charge to 100% in 4 hours 2 minutes. The new iPad has a larger capacity battery (42 watt-hours), so using the 10W charger will obviously take longer. If you are using your iPad while charging, it will take even longer. It's best to turn your new iPad OFF and charge over night. Also look at The iPad's charging challenge explained http://www.macworld.com/article/1150356/ipadcharging.html
    Also, if you have a 3rd generation iPad, look at
    Apple: iPad Battery Nothing to Get Charged Up About
    http://allthingsd.com/20120327/apple-ipad-battery-nothing-to-get-charged-up-abou t/
    Apple Explains New iPad's Continued Charging Beyond 100% Battery Level
    http://www.macrumors.com/2012/03/27/apple-explains-new-ipads-continued-charging- beyond-100-battery-level/
    New iPad Takes Much Longer to Charge Than iPad 2
    http://www.iphonehacks.com/2012/03/new-ipad-takes-much-longer-to-charge-than-ipa d-2.html
    Apple Batteries - iPad http://www.apple.com/batteries/ipad.html
    Extend iPad Battery Life (Look at pjl123 comment)
    https://discussions.apple.com/thread/3921324?tstart=30
    New iPad Slow to Recharge, Barely Charges During Use
    http://www.pcworld.com/article/252326/new_ipad_slow_to_recharge_barely_charges_d uring_use.html
    Tips About Charging for New iPad 3
    http://goodscool-electronics.blogspot.com/2012/04/tips-about-charging-for-new-ip ad-3.html
    Prolong battery lifespan for iPad / iPad 2 / iPad 3: charging tips
    http://thehowto.wikidot.com/prolong-battery-lifespan-for-ipad
    In rare instances when using the Camera Connection Kit, you may notice that iPad does not charge after using the Camera Connection Kit. Disconnecting and reconnecting the iPad from the charger will resolve this issue.
    Since you are a new iPad owner .....
    You can download a complete iPad User Guide here: http://manuals.info.apple.com/en/ipad_user_guide.pdf
    Also, Good Instructions http://www.tcgeeks.com/how-to-use-ipad-2/
    Apple - iPad - Guided Tours
    http://www.apple.com/ipad/videos/
    Watch the videos see all the amazing iPad apps in action. Learn how to use FaceTime, Mail, Safari, Videos, Maps, iBooks, App Store, and more.
    How to - Articles & User Guides & Tutorials
    http://www.iphone-mac.com/index.php/Index/howto/id/4/type/select
    iPad How-Tos  http://ipod.about.com/lr/ipad_how-tos/903396/1/
    You can download this guide to your iPad.
    iPad User Guide for iOS 5
    http://itunes.apple.com/us/book/ipad-user-guide-for-ios-5/id470308101?mt=11
     Cheers, Tom

  • Touch Screen and Charge Issue

    Hey everyone, first time here but also registered at precentral
    Asked there, but I'm hoping here would be a better place to voice this issue.
    This is my 2nd New Pre I had as the first one had random keyboard loss when my phone died due to battery. I was able to fix it with a 5th batt pull, but I wasn't chancing it..so swiped it.
    Well, got my phone with 1.2.x out of the box and tested fine at the store. When home and updated to 1.3.1. weeks later the issue.
    touch would random stop working...I had preware so I decided maybe it was a patch or app messing it up (I noticed I didn't have message foward working after update)
    So I Doctored it. The Process went nervously fine, up until I got to the home screen. The Touch went out again!
    But after messing around a bit after getting it back after a battery pull (at the time touch comes and goes) I was easily able to recreate the issue.
    For example:
    Touch = dead, once I plug it into a charger (usb/wall), Touch returns.
    Touch = alive, (after it came back during day) Once I Plug in to charge, Touch gone.
    There was a point that touch wouldn't return if I had the phone slider closed, with screen unlocked. Wether I was plugging it in or removing to charger.
    I hope this makes sense, and really hope its not hardware, as I don't wanna return phone to find out it repeats on a new/refurb one. As this one feels solid in every other dept.
    Q's Did palm change how the phone locks..reacts to charger??
    If so, god, please fix it!
    Post relates to: Pre p100eww (Sprint)

    ok, I left work today. in the elevator down to my car i started pandora, bluetooth. Got in the car, docked the phone, plugged in the aux wire to my radio, charger to the phone. Music, couple of calls, music agian, skipped some songs, changed pandora stations, etc...
    Got home, undocked the phone, unplugged aux cable and charger, close pandora, turn off the light. Grab my stuff, phone rings can not answer it. Screen now does not work anymore.
    Pull the battery twice, no luck. Do some searching and see some post that it is realated to the battery connection and a post that other have got it to work with the charger plugged in.
    I take the USB cable, PC to phone and it starts working!! yeah... mess with that batter and no luck. stops working again. unplug the USB from the PC and it is still working. Uplug the USB from the phone, stops working, plug it back in to the phone, not the PC and the screen works again... not really sure what that is about. now it is working with no wire.

  • Toshiba USB Sleep and Charge causes s3 wake issues

    Toshiba Satellite P500-ST6844
    PSPGSU-0Q2012
    Windows 7 Ultimate SP1 x64
    I have posted before about an issue with my laptop not waking from sleep properly, (see here)
    basically my problem is this:
    I put the laptop to sleep and everything appears to go normally. but when i go to wake the system up, the Toshiba boot logo is shown, and i have lost my windows session. the system acts like it is cold booting, except for a 30 second pause following the boot logo. Just to be clear, once my windows is up and running again my session is not restored, so my system has not gone into hibernation.  this issue does not affect hibernation mode. Hibernation mode works perfectly. Only taking out the battery and unplugging the machine and then pressing the power button for 30 secs. seems to alleviate the issue. but the issue always seemed to return. after much trial and error, I have narrowed down the cause of the issue. if the Toshiba USB Sleep and charge feature is used, the sleep problem is triggered, even if the sleep and charge port is not being used. This issue occurs even in a clean state (clean from a factory restore using restore media). this sleep issue has been occurring since i bought the laptop in 2010, but it has been only in the last 2-3 months that i have been able to narrow down the exact trigger for the issue.
    I have updated to the latest version of the sleep and charge app for my laptop, but this does not seem to help any. the issue does not seem to be triggered by just activating or deactivating the USB sleep and charge feature in bios, but using/configuring the sleep and charge feature using the Toshiba application in windows, does. 
    I don't know if this is indicative of a bios, software, utility, hardware, or power supply issue. I am hoping some one here might have an answer for me, or at least point me in the right direction on where i can go from here.

    this behavior even occurs in a "factory fresh state" - (restored from OS recovery media). In that state, only toshiba stuff is installed..
    Sounds like you found a bug.
    -Jerry

  • Hi i have updated the 8.1 in my i phone 4s . then i got in my home screen i tunes and charging symbol only . its not getting on . can you help me out to solve the issue with my phone ?? thanks.

    hi i have updated the 8.1 in my i phone 4s . then i got in my home screen i tunes and charging symbol only . its not getting on . can you help me out to solve the issue with my phone ?? thanks.

    Hi vijayanandhtkp,
    It sounds like you are getting the Connect to iTunes screen as discussed in this article.
    If you can't update or restore your iPhone, iPad, or iPod touch - Apple Support
    If so, please check out this article as linked from there.
    Use iTunes to restore your iOS device to factory settings - Apple Support
    Thank you for using Apple Support Communities.
    Nubz

  • A few weird issues with my Z2 and charging !

    Hello guys,
    My Z2 is having some really weird issues (not exactly issues but still)
    1) If i am using magnetic charger and if i am charging from less than 15%, it takes like 8hrs to get to 50% or near 50%. But if i am using the normal chager, i am able to get 100% in around 2ish hrs from 15%.I am facing this magnetic charging issue only if the battery % is less than 15%. I use the same charger for both cables. Both cables are original sony products. If the initial battery charge is greater than 15%, then magnetic charger works normally and charges up fast...But if its less than 15%, then it acts weird.
    2) I am able to get 270 Rotation on the desktop screen ONLY when the phone is being charged. Even though i have the auto rotation ON, it doesnt change the rotation in the app drawer or on the initial screen. Once i connect the phone to charge, it can rotate to any side.
    3) The Super Vivid mode gets resetted to NONE randomly.... Why is this ?
    Can somebody help me with these questions ?
    Thankyou !

    2) that is normal if you want the home launcher to rotate without the need of the dock or magnetic cable you'll need to download a third party home launcher.

  • New Mac Battery and Charger Issue

    Ok today I got a new battery from the apple store for my macbook pro. Everything seems to work. As usual with any new battery I wanted to turn my macbook pro off and charge it fully. Well I went to charge it and the light on the indicator was red meaning charging. But all of a sudden the light turned to green. This I know is not correct because I know from when I was in the apple store, the battery was at 56%. So right now I am not charging it because I don't want to destroy this battery like my last one. is this a malfunction with my computer or charger?

    If you have a charging problem, it's probably related to hardware rather than OS 10.4.x. So, suggest you post your question in the MacBook Pro forum http://discussions.apple.com/category.jspa?categoryID=190 where other MBP users hang out.
     Cheers, Tom

  • Tecra M10 - Stuck CTRL key issue -- perhaps to do with BIOS?

    Hello and thanks for reading.
    I recently switched my Tecra M10 to Windows 7 (from XP) and it soon developed the dreaded "stuck CTRL key" issue. This causes the keyboard to behave as if the CTRL key is permanently depressed. Sometimes hitting a combination of keys, or bringing up the onscreen keyboard, temporarily solves the issue, but then it returns.
    It seems to be an issue many people have, with no simple solution. I've looked at every thread about it I can find, and tried many things to do with drivers etc. without any success.
    So firstly, if anyone knows a remedy that works for this particular machine, I would be very grateful to learn it!
    Then, there are two things I've not yet done: update BIOS and disable pinch zoom.
    I was looking at the following BIOS update:
    http://www.toshiba-asia.com/sg/support/drivers/details/25244
    ... which is version 3.00 and seems to be most recent. My own version is 1.90.
    However version 3.00 is labelled "For PTMB0* ONLY". I don't know what this means or whether it applies to me. Can anyone help? Should I install this BIOS?
    For the pinch zoom, I've been told that disabling it does sometimes cure the CTRL problem -- but I can't find any pinch zoom facility on the M10. I suspect it simply doesn't have one. Is that right?
    Many thanks for any help you can give.

    Hi
    > I was looking at the following BIOS update. which is version 3.00 and seems to be most recent. My own version is 1.90.
    There are different Tecra M10 models on the market.
    Check the labels at the bottom of the unit. There you should find some numbers like for example PTMB0E-01K00LGR
    The first 6 characters are important: for example PTMB0E
    I assume your notebook belongs to European series.
    In such case you should check the Toshiba EU driver page for possible BIOS update.
    http://www.toshiba.eu/innovation/download_drivers_bios.jsp
    However, on Toshiba EU driver page you will find also the BIOS v3.0 for all European Tecra M10 units.
    Anyway, back to the CTRL button issue: guess what, you should connect an external USB keyboard and should check how the CTRL button acts.
    In case the USB keyboard would work properly, the CTRL button of internal keyboard is affected and you will need to replace the internal keyboard.
    PS: it could be possible that the option "sticky keys" has been enabled. To disable this function, you have to press SHIFT button 5 times in the row.

  • P key issues on Macbook pro

    Hello! A few nights ago my girlfriend's lowercase p key stopped working properly. When pressed it activates the volume down function on F11. The uppercase P works however, but she recently told me that pressing capslock makes a comma. It is a 15 inch 2011 Macbook Pro. Any ideas as to what the issue is or what to do to fix it?

    Hold down the option key and select the Wi-Fi menu in the menu bar. What values are shown for the following?
              PHY Mode
              Channel
              Security
              Signal/Noise or RSSI
              Transmit Rate
    Please do not post the BSSID, as that information is private.
    Now hold down the option key again and select
               ▹ System Information... ▹ Network ▹ Wi-Fi
    Compare the two-letter Country Code with the ISO code for your country. Does it match? The code X0 means that the country couldn't be determined. The code X3 means South America, not otherwise specified.

  • Windows 8 Key Issue

    Here's my problem.  Windows 8 came preinstalled on my computer; however, I accidently deleted the Windows 8 key from the bios and now Windows keeps asking me to enter the correct key.  Since there is no longer a sticker with the key included with the computer I have no way of finding the key.  Does HP keep a record of the keys tagged to the serial number?  Or am I just out of luck?
      I called HP Support about this and they told me to get the key off the CDs which were included with the computer.  When I told him there were no CDs, he said I had bought a used computer mascarading as new because all of their computers ship with Windows CDs.  When I disputed this he said that Microsoft could solve the issue for me.  Microsoft said that HP could solve it.  Can anyone help me?  I'd rather not spend money on buying Windows 8
    Thanks in advance,
    Mike
    This question was solved.
    View Solution.

    HP does not retain records of the keys issued .  HP also does not ship Windows CD's with the computers unless they were specifically ordered.  If you have somehow deleted the key then you are out of luck, sorry.
    Please mark my post as SOLVED if it has resolved your problem. It helps others with similar situations.

  • T400 stuck key issue

    I bought my T400 2764-CTO in last December, and started using it on mini dock without any problem. Until recently, it starts to show stuck key issue randomly (not always failure) both at boot up or under Windows Vista.
    ERROR
    0210 Stuck Key FF
    Press <F1> to SetUp
    Note: the stuck key keeps changing, sometimes 13, sometimes 1F, sometimes other key.
    I opened the laptop, and checked the connection of the keyboard but couldn't locate any problem there. Can this be a keyboard issue? Or even a motherboard issue?
    Can Lenovo swap a new keyboard for me? If so, what do I need to do then? 
    Thanks!
    Best Regards  

    You can call Lenovo service, and log a service call, they will make the necessary arrangements. If you are not confident with bios update then please don't do it youself, and let the warranty department do it for you, as any mistakes can make your laptop useless and you will be paying couple hundreds of euros to get the motherboard replaced. 
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • Process key issue in MM

    Hi All,
    I am working on 0PUR_C01 cube and theDS is 2lis_02_itm.i am facing a issue with the process key ,only process keys 2 and 3 are coming into the BI system even though process key 1 and others are also there in the source.
    i have maintained the BF 11 flag and industry sector in mcb_.
    please suggest.
    Thanks
    Sri

    Hi, i'm having the same problem. Can you give me some guidance in how you solved the problem?
    Thank you.
    GG

Maybe you are looking for