Torch 9800 crashes Wifi networks

I've had a Torch for about 2 years now and I've always had this issue but I fiugre I'd finally look into it. This is the 2nd Torch I've had (first one the screen was defective after a couple months) and both have had the exact same issue.
When I use my phone on Wifi, it works fine for about 10-15 minsutes and then crashes the router that it connects to making the internet on the whole network go down. this happens at home, at other peoples homes, at work or even in public wifi areas like hotels or retail stores (yes I've tried it a few different places)
I've tried calling my phone provider a long time ago and they were stumped at this issue but since the wifi technically works the stores refused to do anything on a warranty basis while it was still active. It's not like wifi is a must for me, the internet speed on the torch is still quite slow and I have tons of data on my plan that I don't use but I wouldn't mind getting it fixed so that I can actually turn on my wifi antenna without worrying about crashing everyone's networks.
Thanks!
Chris

I also have the same problem, it crashes networks and routers etc I think it maybe some of the apps that cause it ones that also use the GPS to find your locations etc

Similar Messages

  • IOS 8.0.2 on iPhone 4S crashes WiFi network

    Question:
    Has anyone seen problems with their WiFi network associated with iOS 8.0.2?
    Background:
    I installed 8.0.2 on my iPhone4S and it appears to crash my entire home WiFi.  I have 4 iOS devices in the house: iPhone 5, IPad, Apple TV and iPhone 4S.  Only the 4S has IOS8.0.2.  Since I installed it this morning my WiFi has been continuously crashing, making it impossible for the 4 Windows laptops in our house to stay connected.  I left the house for 2 hours and things went back to normal.  When I returned, the network immediately crashed again.  I turned off WiFi on the 4S and power-cycled the router.  The network came back up.  When I restarted WiFi on the 4S, it crashed.  Turned off the 4s's WiFi again and reset the router.  Everything has been fine now for 30 minutes.  I have Frontier Communications FIOS with a MI424WR-GEN3I router.  Throughout all of the outages, the wired/Ethernet functionality of the router has worked fine and I have been able to access the Internet via Ethernet.

    sstelter wrote:
    Sorry, but that's just a ridiculous thing to say. The fact that an issue is intermittent or dependent on other variables does not mean its not an issue.  You have provided an opinion with no data and no help.  If you can't contribute to a solution, please abstain from this thread.
    If a device on a network can crash a router/WAP, the issue is with that router/WAP is there is no "crash the network" command within the Wi-Fi protocol.
    That's why there are networking standards; if properly adhered to they dictate what will occur when commands are received and commensurately, the only things that will happen.
    Feel free to fill out the form and peruse the actual specifications of the protocol yourself if you so choose; there's no "crash network" option.
    http://standards.ieee.org/getieee802/download/802.11n-2009.pdf
    Whether the router is Apple's or another vendor's, it needs to be able to deal with whatever traffic/commands are sent to it.

  • Time machine crashes Wifi network

    I have a new time machine which constantly crashes my wireless network. 
    I have tried to contact apple express lane support but the email they have sent me gives a phone number which is unrecognisable from my phone (I think it's a US not a UK number)

    http://www.apple.com/uk/buy/locator/
    This site will provide both retail and authorized servicer/support info.

  • Blackberry torch 9800 wifi connected but no internet

    hi i am using blackbery torch 9800.its giving error that wifi is connected but no internet connection.please help me

    Hi and Welcome to the Community!
    With a strong carrier network signal (e.g., not merely WiFi), I suggest the following steps, in order, even if they seem redundant to what you have already tried (steps 1 and 2 each should result in a message coming to your BB...please wait for that before proceeding to the next step):
    1) Register HRT
    KB00510 How to register a BlackBerry smartphone with the wireless network
    Please wait for one "registration" message to arrive to your Messages app
    2) Resend Service Books
    KB02830 Send the service books for the BlackBerry Internet Service
    Please wait for "Activation" Messages, one per already configured email account, to arrive in your Messages. If you have no already configured email accounts, please wait 1 hour.
    3) Reboot
    With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes.
    See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
    Hopefully that will get things going again for you! If not, then you should contact your mobile service provider for formal support and to ensure that you are subscribed to a data plan from them that is adequate to use the services you desire (many services require a data plan, even if the method of access is only WiFi).
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Torch 9800 wifi problems

    I can connect it to my wireless N router (a D-link DIR-615) just fine.
    However, after a short period of time (not even long enough to watch a full Youtube video), the internet connection just stops functioning, and the little icon (I assume it means 'active' disappears from next to the wi-fi icon, which still indicates the wi-fi is connected.  The only way I can get the internet connection to work again is to disconnect and reconnect the wi-fi, which buys me another minute or so of internet connection.
    It's connected using WPA2, which is configured correctly because the Torch can successfully connect.
    For these purposes, I'm testing this with the  mobile network turned off..  With the mobile network turned on, it will revert back to the 3G connection, which of course I'm trying to avoid when I'm at home...
    Any ideas?  Any further information required?
    Thanks

    As best as I can tell, there's an incompatibility issue with the 'N' wifi connectivity, either in the Torch 9800 or a whole lot of N wireless routers.
    I disabled the 'N' functionality in my DIR-615 router, set it to mixed B and G, and now I have no problems at all with the wifi connection dropping.  Might be a little slower (assuming the Torch does take full advantage of N's extra speed when it works), but it's working well for me now....

  • Torch 9800 not using WIFI

    HI All,
    I got my 9800 from Canada, and using it in Taiwan.
    Model: Torch 9800
    Carrier: ChungHwa Telecom
    OS: 6.0 Bundle 2921 (v6.0.0.666, platform 6.60.241)
    I have the BIS plan from my carrier, and connecting via 3G is OK. The problem is, it seems like it's not connecting via wifi. The setting tells me that I am connecting to my home WIFI router.
    The router is in my living room, and I am using my computer to stream video from internet at this moment, so the WIFI, internet should be ok, in an adequate speed to download hi-res video. I have very low 3G signal in my living room, and I am expecting my 9800 to use the high speed internet, but it seems it's not doing it... It could not even connect to google.com.
    The phone acts like this since I bought it, brand new. But it always acts like this.
    Any suggestion to correct this problem is appreciated. 

    Hi and Welcome to the Community!!
    While connected strongly to your carrier data network, I suggest the following steps, in order, even if they seem redundant to what you have already tried (steps 1 and 2 each should result in a message coming to your BB...please wait for that before proceeding to the next step):
    1) Register HRT
    KB00510 How to register a BlackBerry smartphone with the wireless network
    Please wait for one "registration" message to arrive to your Messages app
    2) Resend Service Books
    KB02830 Send the service books for the BlackBerry Internet Service
    Please wait for "Activation" Messages, one per already configured email account, to arrive in your Messages. If you have no already configured email accounts, please wait 1 hour.
    3) Batt Pull Reboot
    Anytime random strange behavior or sluggishness creeps in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
    Then, check the status of BlackBerry Internet Service via Manage Connections > Services Status. That will tell you the pathway that BIS is using. You should try, when you have a strong WiFi, turning off your Mobile Network radio and see if BIS falls to WiFi for it's pathway. Be advised that I've heard of a few carriers who restrict the use of BIS via WiFi and mandate that all BIS services solely traverse the carrier data network. You would need to talk to your mobile service provider to know if they enforce such a thing.
    Good luck!
    Occam's Razor nearly always applies when troubleshooting technology issues!
    If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
    Join our BBM Channels
    BSCF General Channel
    PIN: C0001B7B4   Display/Scan Bar Code
    Knowledge Base Updates
    PIN: C0005A9AA   Display/Scan Bar Code

  • Safari crashing on Wifi networks

    safari crashes every time I open it when using a wifi network. It works fine when I am using a mobile USB stick for internet though. Can anyone help?

    Ok, I found this under a related thread, and I do have Ghostery installed... someone notes that Ghostery 1.3 still works, while 1.4.1 is causing these crashes. Uninstalling it and seeing if that does it.
    "This is a known issue with Ghostery:
    https://getsatisfaction.com/ghostery/topics/safari_crashing_with_ghostery_enable d?utm_content=topic_link&utm_medium=email&utm_source=reply_notification "

  • Firefox crashes when trying to access WIFI network with security agreement

    When trying to access a WIFI network Firefox will crash immediately. If I use Safari, it will ask me if I want to continue to site 1.1.1.1, but suggests that it has an unknown certificate. Click continue and I am taken to a page where I need to accept the terms of use for the WIFI network. Once I accept the terms, then I can open Firefox.

    When trying to access a WIFI network Firefox will crash immediately. If I use Safari, it will ask me if I want to continue to site 1.1.1.1, but suggests that it has an unknown certificate. Click continue and I am taken to a page where I need to accept the terms of use for the WIFI network. Once I accept the terms, then I can open Firefox.

  • Wifi torch 9800

    Hello, 
    A question to the users Blacberry and in particular the torch 9800. 
    Could make this test to help me to understand. 
    When I connect in WIFI and in WIFI only (connection GSM 2G and 3G cut), it is impossible to me to visit the page of orange.fr as well as that of Blacberry. 
    On the other hand without changing anything I post(show) all other wanted pages with no problem at all with a display different from my PC for example to sfr.fr, to yahoo.fr infotrafic etc... 
    Is it also for you, which explanation?? 
    Thanks to the advance for the answers to this small test. 
    Cordially 
    Gilprem 
    Bonjour,  
    Une question aux utilisateurs Blacberry et en particulier le torch 9800.  
    Pourriez vous faire cet essais pour m'aider à comprendre.  
    Quand je me connecte en WIFI et en WIFI seulement ( connexion GSM 2G et 3G coupée), il m'est impossible de visiter la page d'orange.fr ainsi que celle de Blacberry.  
    Par contre sans rien changer j'affiche toutes les autres pages demndées sans problème avec un affichage différent de mon PC par exemple sfr.fr, yahoo.fr infotrafic etc..  
    Est ce de même pour vous, quelle explication??  
    Merci à l'avance pour les réponses à ce petit test.  
    Cordialement  
    Gilprem  

    As best as I can tell, there's an incompatibility issue with the 'N' wifi connectivity, either in the Torch 9800 or a whole lot of N wireless routers.
    I disabled the 'N' functionality in my DIR-615 router, set it to mixed B and G, and now I have no problems at all with the wifi connection dropping.  Might be a little slower (assuming the Torch does take full advantage of N's extra speed when it works), but it's working well for me now....

  • My torch 9800 doesn't locate 3G network

    my torch 9800 only connects to 2g network. where other torch device connects to 3G my torch 9800 only locates and connects to 2g.

    On your Mobile Network, what is your settings? If you are 3G, switch to 2G and back to 3G. You can perform hard reset by pulling your battery while your BlackBerry is ON and reinsert again. See what happens.
    Please thank those who help you by clicking the button.
    If your issue has been solved, please resolve it by marking "Accept as Solution"

  • Application crashes (after changing wifi network?)

    Hi
    I've noticed that new apps I've installed (facebook, remote, last.fm, twitterific) work fine whilst in the confines of my wifi network.
    However, once I've taken the phone out and about and connected to other networks the apps are rendered unusable - they just crash on startup, all of them
    It doesn't happen with any preinstalled apps?
    Maybe it's just coincidence but either way it renders all that good stuff absolutely useless.
    I've submitted the crash report and manually views the crashes in /username/Library/Logs/CrashReporter/MobileDevice
    Doesn't mean much to me though - say's backtrace unavailable and EXCBADINSTRUCTION (SIGILL) is given as the exception.
    Anyone else having the same problems?

    Let's look for another possibility -- does it also happen after you sync the phone to iTunes? If you sync the phone but do not copy apps purchased on the phone back to iTunes it is well-known that they will stop working on the phone. There's even a warning about this in the iPhone prompt that asks if you want to sync the apps to iTunes. If you have never seen this prompt you probably ignored it some time in the past after purchasing music. It will not re-prompt you if you ignore it.

  • Torch 9800 shutdown when on 3G

    Hi, Been searching a solution. Hope this will help...
    I hv been using the Torch 9800 for about 1.5 yr. Recently, it started to shutdown unexpectedly, evenif battery is still at 90% or so. Here are the my current config:
    6.0 Bundle 862 (v6.0.0284, Platform 6.4.0.120)
    3G Bands 1,2,5,6
    The most recent Apps update was Facebook (3.1.0.17). But the issue started just before the last Facebook update. I have minimum apps downloaded (<10), and I do not download music etc. Did a SW update check and got a confirmation that the Torch SWs are all up to date (from Phone/Software Updates). Storage is about 50% filled for both buit-in & media card. 
    Most of the shutdown happen unexpectedly. No warning or whatsoever. There were a couple of incident where there was a brief msg pops up indicating the battery power is drained. 
    While debugging the issue, I notice that the shutdown only happen when I was on 3G. Knowing that 3G consume more power, I suspect it could be a battery issue. But serching online, it doesn't seem necessary a battery issue. I do not want to spend $$ on a new battery and not solving the problem. The physical appearence of the batter looks perfectly good (no deformation or any sort).
    For the past one week or so, after the device was shut down. I normally do a battery pull. But it didn't help at all. After leaving the battery out for a minute or so, and the long reboot, once on 3G, it will go down again within a minute or so. If I turn off the 3G immediately after boot up, and continue to use WiFI, then it will stay on. But once I turn 3G back on, it will go down again, especially when I running the browser. 
    Hope you can help... 

    Hey kytham,
    Welcome to the BlackBerry Support Community Forums.
    Thanks for the question.
    To determine if this a software issue, I suggest performing all the steps in this KB article and test out the 3G prior to restoring any data: www.blackberry.com/btsc/KB11320
    If the issue persists, then I suggest you contact your network service provider for repair/exchange options.
    Let me know if you have any more questions.
    Cheers.
    -ViciousFerret
    Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
    Be sure to click Like! for those who have helped you.
    Click  Accept as Solution for posts that have solved your issue(s)!

  • Torch 9800 ''email set up icon not responding'' ... unable to edit or set up email accounts.

    Torch 9800, Network provider, O2 UK.
    Although my BlackBerry service with O2 is connected and working as normal, I am totally without email on my Torch 9800. I have owned the Torch 9800 since March. All has been well until last week when I changed the password on one of the 3 email accounts I had set up on my device.  This password change left one of the accounts unable to send or receive mail, and is also what lead me to discover that I could not enter email set up on my device or via my network providers website ( www.o2email.co.uk ) .
    I have spent hours on the phone with O2 discussing this issue. The usual checks and procedures have been carried out, battery pulls, checking settings etc and the service books have been deleted and resent several times. These actions have not resolved the problem but instead led to the loss from my device of the other 2 email accounts which were working correctly but have now disappeared into thin air. Having tried all possible solutions with O2 I now come here looking for an answer.
    When I visit my Network Providers BlackBerry mail service trying to create an account using my pin etc,  I am without fail getting a pop up box containing  the error message ''Your account is not accessible via HTML browser. Please use your devive to access BlackBerry Internet Service''  !?  The result is the same whether I log in from my device over 3G or Wireless, or from a PC (have tried several browsers) .
    On my device, when I click on the Email Accounts icon from the setup menu nothing happens, no response at all. I have tried many times and there is just no way to set up or edit mail accounts. I am without mail on my device and growing increasingly short of patience.
    I am now hoping somebody here can offer me some advice on how to resolve this issue. What use is a BlackBerry without email capabilities ? I see from researching email set up problems on the Torch 9800 that I am not alone here so if somebody at BlackBerry is listening ? If this is a Torch 9800 issue then I am sure you will be doing all you can to resolve this but in the meantime PLEASE help by offering a solution to the issues I have mentioned.
    Thanks
    BlackBerry is for Life not just for Christmas
    Solved!
    Go to Solution.

    Welcome to the forums, bs342!
    Well, since you searched the forums, you are undoubtedly aware that the problem you report is unfortunately a common one these days.  The good news is that RIM is definitely aware of and working on the problem.
    First, let's try something on your computer.  What browser are you using?  Your problem there might just be as simple as clearing cache in your browser, then closing and reopening the browser to try the website again.
    If that doesn't work, try this:
    From your device's browser, go to mobile.blackberry.com. Select your country of choice, then go to Communicate>Email. Scroll down to Other Personal Email and click on Integrate Now, then Launch Email Setup. You should be able to integrate your e-mail accounts that way until RIM has fixed this issue.
    Please let us know how it goes!
    *** If I've been helpful please consider clicking the LIKE BUTTON beneath my post.
    *** Please remember to mark your thread as "Resolved" by clicking on OPTIONS to the right of the post and selecting "Accepted Solution."

  • My iMac suddenly no longer connects to wifi network when in KIOSK (username) mode, and only connects when as ADMINISTRATOR mode. Its strange because the iMac has been working fine in KIOSK mode for over a year until 2 days ago.

    My iMac suddenly no longer connects to wifi network when in KIOSK (username) mode, and only connects when as ADMINISTRATOR mode. Its strange because the iMac has been working fine in KIOSK mode for over a year until 2 days ago.

    One of the memory cards was indeed faulty, and the other completely fine
    Thanks very much for all your help!
    Although there is one little thing that I've noticed. The iMac works properly, but I tried to software update to see if that may help my Minecraft sound issue (as I still don't think only having 2GB instead of 4GB would cause such a problem) but the software update application won't work. Running the "Software Update" from the apple menu on the toolbar gains no response, nothing happens. If I run the software update from  system preferences, the application icon appears for a second, then disappears (as in the blank app. icon, the blank canvas with the pencil, pen and ruler in the bottom right corner). It does this every time I try to run it. It did work when the computer was crashing, but this started when on one of the occasions I ran the app. while it was crashing. Since this occured during the crashes, and still occurs now, I'm wondering did something simlar happen minecraft, as it's sound disappeared during the crashes and is still gone now.
    However, the computer is now working again without crashes, which is the main thing, thanks for helping me fix the issue
    Edit: I would mark the topic as solved, but I'm unsure if this would lock the topic or something simlar, so I'd rather leave it open for any ideas regarding the software update and Minecraft issues I'm having

  • Wifi network failing, but Chrome is fine!

    Hi,
    I've recently started to have terrible problems with my wifi network: i thought perhaps i was losing internet connectivity, but this is not the case.
    All i can say is that periodically my internet apps lose connection, and then i will notice i've lost network connection.
    Eventually, some of it is restored, but this time i noticed something interesting: I can use Chrome fine, I can now see my network, but apps such as Slack and Safari are totally failing to connect.
    This is a brand new Macbook Pro with16GB Ram, a 521MB SSD, and the latest Yosemite OS (10.10.4 14C109)
    From my perusing, i noticed that often a log is requested from EtreCheck, so I include one here in advance, taking whilst Chrome is working but Safari etc are not.
    Thanks
    -Mark
    Problem description:
    No network over wifi : Chrome is working ok, but Safari is failing as is Slack
    EtreCheck version: 2.1.7 (114)
    Report generated 30 January 2015 13:45:08 GMT
    Download EtreCheck from http://etresoft.com/etrecheck
    Click the [Support] links for help with non-Apple products.
    Click the [Details] links for more information about that line.
    Click the [Adware] links for help removing adware.
    Hardware Information: ℹ️
        15" MacBook Pro with Retina display, discrete NVIDIA graphics (Late 2013)
        MacBook Pro - model: MacBookPro11,3
        1 2.5 GHz Intel Core i7 CPU: 4-core
        16 GB RAM Not upgradeable
            BANK 0/DIMM0
                8 GB DDR3 1600 MHz ok
            BANK 1/DIMM0
                8 GB DDR3 1600 MHz ok
        Bluetooth: Good - Handoff/Airdrop2 supported
        Wireless:  en0: 802.11 a/b/g/n/ac
        Battery Health: Normal - Cycle count 8
    Video Information: ℹ️
        Intel Iris Pro
        NVIDIA GeForce GT 750M - VRAM: 2048 MB
            Color LCD spdisplays_2880x1800Retina
            Thunderbolt Display 2560 x 1440
    System Software: ℹ️
        OS X 10.10.2 (14C109) - Time since boot: 17:0:59
    Disk Information: ℹ️
        APPLE SSD SM0512F disk0 : (500.28 GB)
            EFI (disk0s1) <not mounted> : 210 MB
            Recovery HD (disk0s3) <not mounted>  [Recovery]: 650 MB
            Macintosh HD (disk1) / : 499.10 GB (381.15 GB free)
                Core Storage: disk0s2 499.42 GB Online
    USB Information: ℹ️
        Apple Internal Memory Card Reader
        Apple Inc. BRCM20702 Hub
            Apple Inc. Bluetooth USB Host Controller
        Apple Inc. Apple Internal Keyboard / Trackpad
        Apple Inc. Display Audio
        Microsoft Microsoft Optical Mouse with Tilt Wheel
        Dell Dell USB Keyboard
        Apple Inc. Apple Thunderbolt Display
        Apple Inc. FaceTime HD Camera (Display)
    Thunderbolt Information: ℹ️
        Apple Inc. thunderbolt_bus
            Apple Inc. Thunderbolt Display
    Gatekeeper: ℹ️
        Mac App Store and identified developers
    Kernel Extensions: ℹ️
            /Applications/Parallels Desktop.app
        [loaded]    com.parallels.kext.hypervisor (10.1.2 28859 - SDK 10.7) [Support]
        [loaded]    com.parallels.kext.netbridge (10.1.2 28859 - SDK 10.7) [Support]
        [loaded]    com.parallels.kext.usbconnect (10.1.2 28859 - SDK 10.7) [Support]
        [loaded]    com.parallels.kext.vnic (10.1.2 28859 - SDK 10.7) [Support]
    Startup Items: ℹ️
        ciscod: Path: /System/Library/StartupItems/ciscod
        MySQLCOM: Path: /Library/StartupItems/MySQLCOM
        Startup items are obsolete in OS X Yosemite
    Launch Agents: ℹ️
        [loaded]    com.cisco.anyconnect.gui.plist [Support]
        [loaded]    com.oracle.java.Java-Updater.plist [Support]
    Launch Daemons: ℹ️
        [running]    com.cisco.anyconnect.vpnagentd.plist [Support]
        [loaded]    com.microsoft.office.licensing.helper.plist [Support]
        [loaded]    com.oracle.java.Helper-Tool.plist [Support]
        [loaded]    com.oracle.java.JavaUpdateHelper.plist [Support]
    User Launch Agents: ℹ️
        [loaded]    com.citrixonline.GoToMeeting.G2MUpdate.plist [Support]
        [loaded]    com.google.keystone.agent.plist [Support]
    User Login Items: ℹ️
        Flux    Application  (/Users/[redacted]/Applications/Flux.app)
        iTunesHelper    Application  (/Applications/iTunes.app/Contents/MacOS/iTunesHelper.app)
        Dropbox    Application  (/Applications/Dropbox.app)
        Alfred 2    Application  (/Applications/Alfred 2.app)
        Google Chrome    Application Hidden (/Applications/Google Chrome.app)
        BetterTouchTool    Application  (/Applications/BetterTouchTool.app)
    Internet Plug-ins: ℹ️
        MeetingJoinPlugin: Version: Unknown - SDK 10.6 [Support]
        SharePointBrowserPlugin: Version: 14.4.7 - SDK 10.6 [Support]
        QuickTime Plugin: Version: 7.7.3
        JavaAppletPlugin: Version: Java 8 Update 31 Check version
        Default Browser: Version: 600 - SDK 10.10
    User internet Plug-ins: ℹ️
        CitrixOnlineWebDeploymentPlugin: Version: 1.0.105 [Support]
    Safari Extensions: ℹ️
        1Password [Installed]
        Open in Internet Explorer [Installed]
    3rd Party Preference Panes: ℹ️
        Java  [Support]
        MySQL  [Support]
    Time Machine: ℹ️
        Skip System Files: NO
        Mobile backups: ON
        Auto backup: YES
        Volumes being backed up:
            Macintosh HD: Disk size: 499.10 GB Disk used: 117.95 GB
        Destinations:
            TimeMachineBackup [Network]
            Total size: 1.92 TB
            Total number of backups: 15
            Oldest backup: 2015-01-11 18:24:44 +0000
            Last backup: 2015-01-30 13:01:55 +0000
            Size of backup disk: Excellent
                Backup size 1.92 TB > (Disk size 499.10 GB X 3)
    Top Processes by CPU: ℹ️
            15%    WindowServer
             6%    prl_vm_app
             4%    Google Chrome
             3%    Safari
             3%    prl_client_app
    Top Processes by Memory: ℹ️
        893 MB    prl_vm_app
        567 MB    idea
        447 MB    Finder
        395 MB    prl_client_app
        326 MB    WindowServer
    Virtual Memory Information: ℹ️
        2.55 GB    Free RAM
        6.92 GB    Active RAM
        4.39 GB    Inactive RAM
        3.31 GB    Wired RAM
        27.59 GB    Page-ins
        3 MB    Page-outs
    Diagnostics Information: ℹ️
        Jan 29, 2015, 08:47:06 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/QuickLookSatellite_2015-01-29- 204706_[redacted].crash
        Jan 29, 2015, 08:45:43 PM    Self test - passed
        Jan 29, 2015, 02:48:07 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/p4v_2015-01-29-144807_[redacte d].crash
        Jan 29, 2015, 02:39:13 PM    /Library/Logs/DiagnosticReports/p4v_2015-01-29-143913_[redacted].hang
        Jan 28, 2015, 02:00:38 PM    /Library/Logs/DiagnosticReports/App Store_2015-01-28-140038_[redacted].hang
        Jan 27, 2015, 04:51:03 PM    /Users/[redacted]/Library/Logs/DiagnosticReports/Google Chrome_2015-01-27-165103_[redacted].crash

    1. Power off the router. Unplug it from the wall. Wait a while.
        Plug it back to the wall. Power the router on. Wait until all the lights are lit properly. It will take a while.
        Restart the computer.
        Start up in Safe Mode.
        http://support.apple.com/kb/PH14204
    2. Deselect Proxies if selected.
       System Preference > Network > Advanced  > Proxies Tab
       Under "Select Protocol", uncheck any box if selected.
       Click "OK" then  "Apply”.

Maybe you are looking for

  • AP Credit Memo on AP Invoice with a downpayment amount linked

    Hi all. I would like to know the y is it not possible to create a A/P Credit Memo on an A/P Invoice which is adjusted with A/P Downpayment amount. If the above posting is made in the system, its not possible to Copy to AP Credit Memo, the AP Invoice

  • Sort to subfolders based on last three letters of file

    I am working on a script i found that will take the contents of a folder and seperate them into sub folders based on the last three characters of the file name. They are named by user and month for example: Sam_Jan.xlsx. Here is what i have so far: p

  • LM46: Error Target handling unit NNN is not assigned to TO MMM.

    In LM46, if we select the material with F1, it works. If we initialize o_ltap_kzqui = 'X' in the User Exit EXIT_SAPLLMOB_480 we get the error. Is there an issue about that?

  • Lightroom Adobe Revel Smart Collections

    Hi There, when i first tried the export function from LR to Revel i was totally thrilled because most of the time i work with smart collections. i just upoaded them to Revel from LR. From time to time some of the photos belong to more of one smart gr

  • How to move NEF pictures in a folder on my desktop

    Hi all, I'm new to mac and have been playing a bit with iPhoto and it really seems great. Here is my problem, I have a D90 which takes JPG and NEF pictures at the same time. When I import my pictures in iPhoto it puts both files next to each other. H