Torch 9810 slow red flashing light then black screen

Hi,
My phone is over 1 year old, so its not covered by Wind provider warranty. its 15 months now. One day, I plugged into the computer, it was doing an OS update, then froze at 30%. ever since, it is flashing red a few times then nothing... complete black screen. I tried it on different computers and even went to retail store and they tried it, nothing. They said its a blackberry OS issue and need to restore to factory OS and let it do update again. how do i do this? I know its not battery issue because we tried other good batteries. help!!

Hi and Welcome to the Community!
Please refer to this official download portal as you proceed. It is sorted first by carrier -- so if all you want are the OS levels your carrier supports, your search will be quick. However, some carriers are much slower than others to release updates. To truly seek out the most up-to-date OS package for your BB, you must dig through and find all carriers that support your specific model BB, and then compare the OS levels that they support.
http://us.blackberry.com/support/downloads/download_sites.jsp
From a PC, you can install any compatible (e.g., for your exact BB Model Number) OS package to a BB via this procedure:
http://supportforums.blackberry.com/t5/BlackBerry-Device-Software/How-To-Reload-Your-Operating-Syste...
Note that while written for "reload" and the Storm, it can be used to upgrade, downgrade, or reload any BB device model -- it all depends on the OS package you download and install to your PC. After installing the OS package to your PC, please remeber to delete, on your PC, all copies of VENDOR.XML...there will be at least one, and perhaps 2, and they will be located in or similarly to (it changes based on your Windows version) these folders:
C:\Program Files (x86)\Common Files\Research In Motion\AppLoader
C:\Users\(your Windows UserName)\AppData\Roaming\Research In Motion\BlackBerry\Loader XML
Be sure that you remove, from your PC, any other BB device OS packages as having more than one installed to the PC can cause conflicts with this procedure.
You may also want to investigate the use of BBSAK (bbsak.org) to perform the wipe it is capable of.
You may also want to try the "Bare Bones OS Reload Procedure" to attempt to narrow down the precise causal item:
Load your OS "bare bones"...if anything is optional, do not install it.
If the behavior presents immediately, then try a different OS with step 1
If the behavior does not immediately present, then run for as long as it takes for you to be sure that the behavior will not present.
Add one thing -- no matter how tempting, just one.
If the behavior does not present immediately, then again run for long enough to be sure it will not have the same problem
Repeat steps 4 and 5 until all things are loaded or the behavior presents
When the behavior presents, you know the culprit...the last thing you loaded.
If the behavior does not re-present, then you know that either step 1 or 2 cured it.
If the behavior presents no matter what, then you likely have a hardware level issue for which no amount of OS or software can cure.
You may also need the use of these tricks:
KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
KB27956 How to recover a BlackBerry smartphone from any state
http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
If you are on MAC, you are limited to only your carriers sanctioned OS packages...but can still use any levels that they currently sanction. See this procedure:
KB19915How to perform a clean reload of BlackBerry smartphone application software using BlackBerry Desktop Software
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Similar Messages

Boot Camp won't boot Win 7 DVDs /Cloned disks - White cursor flashes once then Black Screen of Death.

Hi Guys,
I am having a serious issue with my machines ability to use boot camp. Here's what happend: I had Win 7 installed on the BOOTCAMP partition for a long while, then one day my HD crashed. So naturally I got my HD replaced from Apple and got Lion reinstalled and wokring flawlessly. Then I planned to get my Boot Camp going again, but my computer has a will against it I swear. So I run Boot Camp Assistant , create the parition and reboot. At this point I have my Win 7 disk burned using Disk utility in the drive, I am using a dvd disk image from Microsofts online store. I reboot and the computer hangs at the "pick a harddrive" grey for a second. Then the DVD drive spins up and I get a black screen, then for ever so slight a moment there is a flash of a white _ a the top left, then flash , nothing, the screen remains illumniated. Now I tried this multiple times , let it run over night , and nothing. Its almost as if my laptop will no longer boot the style of dvd that win 7 is.
Being a diagnostics first type of a person I tested all the variables, the win 7 cd works fine in other macbook pros. My computer boots other mac os x DVDs without a problem. I also tried using winclone to create a copy of another machines Boot Camp and flash it to my BOOT CAMP drive but this has the exact same result! Therefore it seems that the underlying system that runs my Macs ability to boot from Windows-style? partitions and dvd is broken. I also tried installing rEFIt, but that doesn't seem to help. I also tried booting off of an external USB drive with the same result. I tried zapping p-ram , scm and doing all software updates.
Has anyone expereinced anything like this? Anyone found resolution to a similar issue? Any other tricks related to Macs EFI and boot process that I could use to debug this? Anywhere that EFI stores logs possibly?
I went to the Apple's Genius Bar and they were stumped on my issue. I felt that they should be able to fix it considering it booted fine before I had Apple replace my HD.
Thanks to any responders, I'm really hitting my head on the table now and would love some help.

Have you reset the PRAM? It should usually be done when replacing any hardware. Have you got the latest EFI firmware for your Mac?
Not knowing what model /YEAR your MBP is (not that it would help me too much but the other fellas probably would) it's hard to guess as there are issue's for different models. The only thing I could find was it's usually caused by a non-conforming video driver. Microsoft had a page on it I found by accident and now I can't find it!
WinClone hasn't been updated by the original author in over a year, others have tweeked it a little to work with W7 but seems to be semi reliable, so the be aware.
Unless the other MBP's are identical in Model AND year your putting older or incompatible drivers on your MBP. Boot Camp, (especially if your using the drivers on the original install disks, like 10.6 and earlier) will only install for that specific computer. Just like the OS installer.
EDIT:
Oh yeah, are you sure you have the partition formatted the right way, thats another black screen problem.
Message was edited by: Jaygyver

Black screen red flashing light

Plz help.
Today my touch screen on my bb torch 9800 wouldnt work, I did a battery pull and now my phone wont switch back on. the screen is black and there is a red flashing light.
I have had my bb neary 18 months and never had a prob before.
Can you advise what i should do next,

Hi and Welcome to the Community!
Put your BB onto a known-good wall charger for 2 hours, and do not touch it. Then, with it still on that charger, remove the battery, leaving it out for 5 minutes (with the BB still on that charger!). Put the battery back in. If it boots up, leave it alone (still on the charger) for 5 hours to see if it will fully charge and function again.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Hey Dears, I was working with my Macbook pro 2011, then i have some flash light in the screen, so i shutdown the computer, when i try to open it again i had a black screen, so any one of you have any idea about what should i have to do ?

Hey Dears, I was working with my Macbook pro 2011, then i have some flash light in the screen, so i shutdown the computer, when i try to open it again i had a black screen, so any one of you have any idea about what should i have to do ?

Can you start Firefox in [[Safe mode]] ?
You can also do a clean reinstall and download a fresh Firefox copy from http://www.mozilla.com/firefox/all.html and save the file to the desktop.
Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
You can initially skip the step to create a new profile, that may not necessary for this issue.
See http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

MiFi2200 has a red flashing light

MiFi2200 has a red flashing light and will not get a signal. When it's plugged into the wall, the button light flashes red. When I plug the device into the computer, Verizon manager doesn't detect the device.

wobbly214 wrote:
MiFi2200 has a red flashing light and will not get a signal. When it's plugged into the wall, the button light flashes red. When I plug the device into the computer, Verizon manager doesn't detect the device.
You may have discovered by now:
"Red Blinking The battery is critically low."
Leave it plugged in for a while.
The LED can be Green, Green/Yellow which the book calls Amber, or Red.
http://support.vzw.com/clc/devices/index.html?p=5607&m=
Device Manual
Clarence

Hp pavilion dv7-1451nr caps and number flashing once. Black screen

HP Pavilion dv7-1451nr: caps and number flashing once. Black screen. I took out top memory card then laptop booted.
Shut off and booted about 5 times no problem. Shut off overnight. Now same problem reoccurred.
Thanks for any advice, Stan

Hi
1 Blink normally indicates a Processor issue. for more info
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01732674&lc=en&jumpid=reg_r1002_us...
Hope this helps.
***** Click the KUDOS Thumbs UP (Like) on the left to say 'Thanks'*****
****Make it easier for other people to find solutions, by marking my answer “Accept as Solution”&"Kudos"if it solves your problem.****
-VJ
Although I am an HP Employee, I am speaking for myself and not for HP.

Ipod touch 5th generation battery screen with lightning bolt locked cannot charge or restart. ive tried everything from new cables attempting to shut down but stays at screen for a few seconds then black screen again over and over

screen locked up and shows the battery with low red and ligtning bolt and cannot hard shut down or reset just stays there for a few seconds then black screen. hooked up to computer and itunes doesnt recognize it or even shows that it is pluged in. looked and made sure nothing is broken or metal in ligting port or on cable which would prevent it from accepting a charge. ipod is only a month old and seems like a waste of money if its so hard to try to get an explanation of why this is ive been tryning to get an answer from apple for a week now.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try on another computer
- Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

I keep getting a message to update my flash player, then a screen showing flash player pro appears, I don't have this on my iPad that I'm aware of. I cannot view videos etc (new to ipad) can anyone assist please.

I keep getting a message to update my flash player, then a screen showing flash player pro appears, I don't have this on my iPad that I'm aware of. I cannot view videos etc (new to ipad) can anyone assist please.

Adobe has not made a version of Flash for the iPad.
Kappy explains why. https://discussions.apple.com/message/19446567#19446567
5 Flash Player Alternatives http://www.techshout.com/features/2011/01/flash-player-for-ipad-apps/
Top 4 browsers supports flash player on iPad and iPhone
http://mashtips.com/flash-player-ios/
 Cheers, Tom

While loging in my Facebook account apple logo shwed up then blue screen then black screen and my phone didnt work ever since . what is that

I searching my Facebook account when apple logo showed up then blue death scree then black screen after all white and black stripped screen . It happened for a few times the the phone went off and didn't work ever since . What was that ?
And how can it be solved ?

Back up and restore your software via iTunes. If the problem continues, restore as a NEW device. If this solves it, that means there is some corruption in your backup file, or maybe it's one of your apps causing the trouble. If the problem is still there, you should take it to the Genius Bar at an Apple Store for evaluation.
For the charging problem:
Inspect the charging port area for dirt/debris/fluff build-up that may be preventing a good connection and use a wooden toothpick, soft clean toothbrush, or a can of compressed air to clean it. Also look for bent or broken pins. Try another cable and/or charger block (be sure to always use a genuine Apple certified brand) in a known good outlet. If you're using a USB port, try another port. If you're using a hub, try a direct connection. If you're using a USB port in the front of a desktop computer, try one in the back. If all these fail, make an appointment at your nearest Genius Bar to have the device evaluated.

MSI GE70 botting and then black screen :(

Hello!
I recently got my laptop back from service repair, because it had Hard drive problems, and HDD was changed with new one.
But today, when I was playing a game, the PC froze, so i turned it off and now, I get to windows bootup sequence, and then black screen :(.
Is there anything that could be done, or I would need to send it back to service repair and wait anohter month to get it back?
Kind regards.

Same problem here. The update killed my video. Tried rebooting three times. The audio is fine. I hear the reboot audio. I hear clicks when I press buttons on the remote. But, there's a blank screen.

Red orange flash on startup then black screen

My macbook was working well one second, and thewn the screen went black. I tried rebooting, but i get a quick red/ orange flash on startup and then a solid black screen. The computer still works, I'm listening to music from it as I write this...
Based on what I've read so far, it seems the only solution is connecting an external monitor or paying out about £200.00 to have a motherboard reinstalled?
Has any one got any thing else on how to tackle this problem?
Thans for any advice!

You need a new screen or new GPU depending on what has gone bad. If the motherboard/GPU is bad then you will not be able to use an external monitor. So if you can use an external monitor then it's more likely that the screen is bad.

Red Flashing Light on ImageCLASS8280Cw

I've just unpacked my MF8280Cw, pulled the strips from the cartridges, and added paper to the paper drawer. The red error light continues to flash - all this prior to attempting to connect the printer to a PC.
There doesn't appear to be a paper jam. I've removed the tray, re-inserted it and rebooted the printer several times.
I then plugged the printer to the laptop via USB cable but the Windows8 PC didn't recognize a printer.
Are there any other things to check for, or did I get a dud?
Thanks for your time.
Patrick

I took another attempt at getting the printer to work today. I powered it up, and stepped through the setup menu. After completing the menu options I now receive the following error message:
"Remove tabs/pieces of tape from the toner cartridge. Black(K)
I had, of course already removed the tape by pulling out the orange ring. Any thoughts?
Patrick

Red flashing light on device

My Curve 8520 will not switch on today and the red message indicator light flashes once then rapidly 4 times then stops for a few secs then starts again. It looks like a morse code signal. Any ideas please?
Solved!
Go to Solution.

Do a simple reboot on the BlackBerry in this manner: With the BlackBerry device POWERED ON, remove the battery for about five minutes, and then reinsert the battery to reboot. A reboot in this manner is prescribed for most glitches and operating system errors, and you will lose no data on the device doing this.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

BT Broadband - Red Flashing Light on Home Hub and ...

(Posting on behalf of a friend).
Good morning,
Having recently got a the latest home hub (recieved as part of upgrade to broadband package) I currently do not have a working broadband connection. Have been unable to get BT on the phone so posting here (hopefully for a resolution).
The Homehub 5 goes through its start up procedure then goe straight to a flashing red light. It has been installed just over a month and was working at the start of this time.
We have tried leaving it to cool down, removing the phones so only the broadband is plugged in and even resetiing it through the procedure identified in the help documentation. Each time, the same result.... flashing red light!
According to the BT website, the flashing red broadband light means probelm with the broadband line. Is there anything we can do on our end or should we try BT again?
Thanks in advance,
K.

are there any problems in your area http://usertools.plus.net/exchanges/mso.php
http://usertools.plus.net/exchanges/?
http://btbusiness.custhelp.com/app/service_status
http://bt.custhelp.com/app/answers/detail/a_id/15036
http://community.plus.net/exchange-information/
If you like a post, or want to say thanks for a helpful answer, please click on the Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

HELP Needed ASAP! Curve Not Turning On, Red Flashing Lights!

Hi,
I have a Blackberry curve 8310. I plugged my curve into my mac to do a software update. Midway through, my phone shut off and hasn't worked since. The battery is fully charged. The phone is off and won't turn on. Additionally, there is a red LED light blinking twice every few seconds. I think I found an article on blackberry.com's knowledge database that diagnosed my issue, but my problem now is that because the curve isn't turning on/off, it's not connecting to my mac's desktop manager. So I can't do anything the article tells me to do. What should I do now? I need help ASAP!
Here's the link to the article: http://www.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB19915
Thanks in advanced!

Hello Asmro and welcome to the BlackBerry Support Community Forums.
It can take up to 30 minutes for the Mac to connect to the BlackBerry.
I would remove your battery and connect to the BlackBerry Desktop Manager. Once it comes up there is no software installed, re-insert the battery and follow the article KB19915.
Let me know how you make out.
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Torch 9810 slow red flashing light then black screen

Similar Messages

Maybe you are looking for