Toshiba 32RL938F: MP4 playback stopps after 2h 6min

Hi everyone,
first time here and I subscribed to this forum just to report that I have a problem reading my MP4's files with an external hard drive. One video file just stopped after 2 hours and 6 minutes (and it lasted for more than 2 hours and 50 minutes).
I tried to read those files on my computer and there was no problem at all.
Can you help me ?
Thanks.
Here is the link to the result of the [MediaInfo Log|http://pastebin.com/NJSx4Msx] of one of my files

Hello, i would like to note that the specific issue about the movies not playing more than 2:05 is not a bug and cannot be fixed by a firmware update. At least for the model 32L4333D i recently bought toshiba responded about a faulty board and the TV needed repair... So you should check for the official support in that case rather to wait for a new firmware that may probably never come.

Similar Messages

CE: Process jstart.exe stopps after reboot

Hello,
Recently I have installed the newest trial version of CE7.1. After finishing the installation procedure I followed the installation manual (which means that I could use CE). Now I have rebootet my System (WinXP SP3) and whenever I try to start CE the Process jstart.exe (work 0) stopps after some seconds. Below I have copied the log. What makes me wonder is the fact, that the process had worked perfectly after the installation.
I hope there is someone who can help me,
Thomas
[Thr 3872] *** LOG => Process collector started (pid 2448).
F
F [Thr 3872] Mon Dec 22 17:38:29 2008
F [Thr 3872] *** LOG => Process collector stopping (pid 2448).
F
F [Thr 2444] Mon Dec 22 17:38:30 2008
F [Thr 2444] *** LOG => Signal 13 SIGCHLD.
F
F [Thr 3872] Mon Dec 22 17:38:30 2008
F [Thr 3872] *** LOG => Process collector stopped (pid 2448).
F [Thr 3872] *** LOG => Instance state is "Synchronizing binaries" (STOPPING @ 0, INACTIVE).
F [Thr 3872] *** LOG => Run level 2 completed.
F [Thr 3872] *** LOG => Instance state is "Some processes failed" (STOPPED @ 0, INACTIVE).
F [Thr 3872] *** LOG => exiting (exitcode 22002, retcode 1).

Hi,
Please go through this thread.
Re: jstart never start in NetWeaver CE 7.1
Regards,
Gayathri

After instaling the update for OS yesterday (saturday 7.10.2012) my macbook pro will not start. The instaling proses start but stopp after 2-3 minutes. I have started mayby 10 tims know but it stops every time. Help, its just a monts ago my iMac hard fail

After instaling the update for OS yesterday (saturday 7.10.2012) my macbook pro will not start. The instaling proses start but stopp after 2-3 minutes. I have started mayby 10 tims know but it stops every time. Help, its just a monts ago my iMac hard fail

Actually it sometimes gets a little further, the display will dim and the pointer will appear and then whoop it will turn off. if i do a verbose start up, it will finish all the steps, the white screen will appear and dim and then it will turn off.

I have Acrobat 8 standard, I can not create PDF file any more. It stopps after 10%. This is happen after I have trayed Acrobat IX prof. demo. I have unstalled and reinnstalled Acrobat 8, the same problem are there. Can sombody help me.

Problem to make PDF file, stopps after 10%?

Hey Tom,
Could you please tell me how have you been trying to create PDFs.
What exact error pops up on your screen when it stops after 10%?
Please specify more on what you mean by saying 'trayed Acrobat IX prof.demo' as I need to analyze what exactly is the trouble.
Hope to get your response.
Regards,
Anubha

Set the Moov in the begining in the mp4 video in after effect or using adobe encode ?

is there a way to set the Moov in the begining in the mp4 video in after effect rendering or using adobe encode, so it can fast start in web or mobile application ?

running After Effects in English, even if you’ve installed and activated it in another language

Playback stops after a second or two

My playback unexpectedly began to stop after only a second or two today. Fast forward stutters too. No change in the computer (except software updates). The file is OK as it plays fine on my laptop. Trashed preferences, restored Garageband from a previous time machine version, turned off my airport, all to no avail. Garageband is completely unusable on my G5 Tower at this point. Any suggestions or help would be appreciated. Repairing permissions right now to see if it helps.

I had the same issues with playback stopping after a few seconds. It began happening in every project that I had.
I tried a vast number of things, changing mac settings, changing garageband settings, software update of garageband etc etc...
Nothing made any difference until late last night. I decided to make a brand new project with one simple recorded audio track to see if the problem would happen with the new project.
Playback worked fine in my new project and then when I checked my other projects, they all worked fine as well.
I don't know whether initialising a new project fixed things or whether it was a coincidence but the problem went away for me.
Good luck

Choppy mp4 playback in iTunes

Until tonight, I've never had issues with video playback in iTunes. I have a library of mp4 video files that I've played successfully in the past with little or no video quality issues.
All of a sudden, none of my videos will play correctly in iTunes. The video is incredibly choppy, with a new frame or two playing every 30 seconds while the audio plays relatively normally. If I open the same file in another player (VLC or WMP), the file will play correctly with no choppiness. In fact, I can play the video file in both players at the same time with zero quality loss, so there's no lack of computer power that would cause this in iTunes. To the best of my knowledge, nothing changed on my system to prompt this - I was literally in the middle of watching a video when it happened.
After experiencing this issue, I upgraded iTunes, Windows, and my video card drivers to the latest versions/drivers (rebooting several times in the process), but this did not help. Next, I followed all of the instructions in the relevant support document (http://support.apple.com/kb/TS1718), also to no avail.
For the heck of it, I rented an HD movie from the iTunes store and had the exact same problem. I originally thought that this might be an issue with my media, but it is clearly not.
I often stream video from my PC to my AppleTV, and this is also experiencing the exact same choppy video (as you would expect).
I have no clue what else to try. I would prefer to watch the videos in another player, but this is sadly not an option if I wish to continue using my AppleTV. Has anyone else experienced this (or a similar) problem? I'm at my wits' end, and very unhappy that I spent so much time transferring my video library into iTunes. Nothing substantial changed on my computer that should have caused this, especially not in the middle of watching a movie. Any help or further ideas would be greatly, greatly appreciated.

Solution: format computer because iTunes is terrible. Problem "solved," I guess

Toshiba 42VL863 and DLNA - disconnection after 30 minutes

I have the television on the network, wired with Category 7 shielded cable, gigabit lan on a switch, such as media servers I have a Qnap TS-509 with DLNA, all connected devices (tablets, PCs, and other devices) reproduce the video stream without problems.
The TV instead: after 30 minutes of playback device tells me disconnected.
I tried everything but I can not see a whole movie.
I demand an answer from toshiba. The money I gave for this TV were not fake but good.

I just contacted the helpline for advice, in addition to not understand at all what I was saying, after making me wait a good five minutes (paying of course) they told me to turn it to the dealer because the television is not under warranty.
If this is the support that you have toshiba from their customers, I will be very happy (being an IT technician in a large company) not to recommend the 'Buy toshiba products.

QT playback delayed after upgrade to 10.6

Just upgraded MacPro Dual Quad to 10.6.
Ran all the updates - everything is current.
Something happened to QuickTime playback, both V10 and V7 Pro have problem playing regular mp4 or m4v files, same ones that my MacBook Pro with 10.6.2 plays just fine.
In short - click on Play button in QT 10, and nothing plays, after a while "application is not responding" will appear in Force Quit window.
Using QT 7 Pro is a bit better, but it takes about 5 seconds till it starts. Sometimes I get a rainbow ball till it start playing....
I ran Snow Leopard Cache Cleaner, then four utilities programs - Disk Utility, Drive Genius, TechTool Pro and Disk Warrior from MacBook while MacPro was in FW Target mode.
No luck.
Downloaded QT 7 to reinstall, but it doesn't let me as QT is "already installed on this drive." And would it help QT 10, that's another question.
I am not new to computers, but seems like a hit a wall.
Am I the only one "lucky" with this ot somebody else had this issue as well?
Any thoughts on what to do next?
Anything will be greatly appreciated!
:: Iggio ::

Hello David,
Thank you for your reply!
I was not clear enough first time, sorry. QT 7 was installed originally during the 10.6 upgrade, I wanted to have it as I have QT Pro license and use its editing features. In my case, QT 7 had a bit less of delay then QT 10 Player. I wanted to reinstall QT 7 hoping it will wipe out some old prefs or other files that may be were left from 10.5... That's when I couldn't install it again, as it was already there.
At this point I crossed the threshold of patience and wiped everything clean.
I had a backup of 10.5.8 of this drive that I made right before 10.6 upgrade (which I recommend to anyone to do), and now I run my MacPro from that drive.
I installed 10.6 after I erased the main drive completely, and will reinstall all the apps and plugs again. It is a massive pain, as I have many audio plugins and video applications, but once it is done the result is usually worth the time and effort.
My friend at APPLE Store always tells me - upgrades are for those who has no patience or on the road Well time for me to have patience.
Thank you for reply - you were the only one out off thousands on this discussion board!
All the best!

Lumia 800 and 23.976 FPS MP4 - Playback Issue

Quite lately, I have been wondering, if I should bring up this issue or not. Thought, what the hell - lets pen it down anyway.
So here's the deal, I have a lot of 720P DTS/DD HD movies which I generally re-encode to H.264 lower bit rates (1500 to 2000 kbps) and Audio to AAC and finally MUX them in MP4 (sounds terrible right !). The resultant file plays fine on VLC, HOWEVER, its terribly laggy/jerky on Lumia 800.
After a lot of hit and trial, I found a workaround though : Mux the H.264 Video stream @ 25 fps and Speed up the Audio from 23.976 to 25. Now the movie playback on Lumia is tolerable but not that smooth.
My N8 can play 23.976 Movies just fine. Now the Question - Why is Lumia 800 not able to playback the most widely used 23.976 framerate encoded movies and why I have to increase the FPS (to 25) in order to achive a decent playback.
PS: Movies which are @ 30 fps has absolutely brilliant playback on Lumia, though. But unfortunately, we cannot speedup 23.976 to 30, coz speeding up the Audio to 30 framerate makes the audio sound terrible and cartoonish.
EDIT : Let's make it more clear. The culprit is not 720p. I even tried resizing the video to 800x450 (Progressive) and keeping the original framerate to 23.976.The playback is still noticeably jerky. So the culprit is definitely the framerate.
Cheers !!

@ noenid : Hey buddy... Still stuck with the playback issue.. I realized that long back and am glad that I finally gave up on Nokia. Few weeks back I just bought Sony Xperia Z. Now that's what a "smartphone" should be... Its almost impossible to find something that the "Z DOESN'T DO"...
Maybe Nokia can convince Microsoft to re-design the Windows Phone OS and bring it at part with other OS. I really don't know why Microsoft chose to go the "Apple Way"... They may say "Security" >> to which I say "**bleep**"....
And why do I say **bleep** ?? Depite all the security and locked OS API's, I still don't see any substantial acceptance of Windows Phone OS in Business community... Android on the other hand, was highly criticized for being "vulnerable" >> But look around man... Almost every banking / IT / Financial Sector have their apps on it.. I really don't want Windows Phone OS to roll-over and die...
As they say: You can fool me once, but not twice...

IPhone 5 music playback issues (after iOS 8 upgrade)

Hi,
After upgrading my iPhone 5 to iOS 8 I have had many playback issues with my Music. Songs randomly skipping or stopping without even doing anything are some of the issues. Also sometimes when I am listening to a song it would fast forward the music.
P.S. I don't sync my music, I just manually add content.
Is there any way I can fix this problem?
Thanks
L

My wife had something like this happen with her iPad. The problem was that the device had not been synced and so some file were not loaded on the device.
The way to correct the problem is to plug the device into the computer and tell it to sync.

Slow preview playback in After Effects

Hi Folks
I just recently set up CS6 on a new z820 workstation and for some reason my after effects timeline does not playback in realtime when previewing. Everything is green on the timeline, yet when it plays it is about half speed. I have no doubt my system has the specs to play rendered media in real time (2x8core, Quadro 4000, 64GB Ram, Sonnet hard drive array) so obviously I have something set up wrong. I'm running a Kona 3 with the latest drivers and I suspect this is the culprit. I've had other issues related to the Kona, such as losing display to my external monitors sporadically. It will be fine for a while then suddenly the output signal turns either solid green or some form of garbled junk. Very strange, although the Kona output seems perfectly fine when I'm in Premiere.
Anyhow, any help zeroing in on the problem would be greatly appreaciated.
Best,
EE

Thanks Tom
However, I do think I have playback set to computer monitor (not in front of system right now). Definitely seems like there's something AE doesn't like about my card (it is an older version of the Kona 3). I have a support ticket in with AJA so hopefully that will turn up something.
As far as my Quadro 4000 goes, I was kind of forced into using it on account of other software on my system. If it was up to me, I would have put in a GTX680 or 690. I have a GTX680 at home and it is rock solid in AE and Premiere. Timelines that are heavily dependant on GPU accelerated FX render about twice as fast on my 6-core/GTX680 vs my z820/Quadro 4000 work system. I'm hoping to upgrade to the Quadro 5000K when it comes out, possibly with the Tesla sidekick. In the meantime, I have to sort out this Kona thing

Avchd imports into fcp 10.0.7 but choppy playback-even after using clipwrap

I am not sure where the problem may be. I record onto the sd card (16gb sandisk extreme class 10, 45mb/s) from brand new canon m500. Card is read in FCP X and can import but when I play back everything is choppy.
I am recording as avchd, mxp-used 60i frame rate & 30 frame both had same issue.
I tried clipwrap and that improved the first 5 seconds and then still choppy for the remainder.
When I playback the sd card inside the camera no problem-looks and sounds great.
If I look at the file on the sd card - after putting sd card in macbook pro (mid 2009-handles FCP just fine) or copying to computer it is titled as "private." I changed the permissions.
I am also using a canon hv 20 (mini dv)-absolutely no problems with import.
Any thoughts or ideas? I am on a deadline and losing a lot of time.

Thanks Alchroma & digibudIl--Iappreciate the quick reply.
I was able to figure out a solution very similar to the suggestion of changing the playback & optimizing media. Here is what I set up. With these setings, the playback of the file before import is still choppy. After import it is still choppy until the background tasks reach 100%-next to the timecode. Once 100% then it playsback smoothly with these settings.
I was using the internal hard drive on my macbook pro. My workflow is to (sometimes) use the internal hard drive and then transfer to external hard drive. Other times import to external hd.
What was interesting to me about the import process is with AVCHD, is that FCP X recognizes the file from the sd card as an avchd file. I did not need to save the files to another folder, create an archive etc. I tried all these with the same result as the simple import in FCP X.
One last question. The Canon M500 can shoot at a frame speed of 60i and 30. Is 30 lesser quality or is 60 better in some way. I will be editing the footage in FCP X.
Thanks again for the help and I hope my experience helps others.

Toshiba Virtual Store works perfectly after update!

Hi
after using my journey, I realized that I have not made ??the right choice.
But when I saw your discussions, I told myself that I have nothing to lose if I do an update.
I followed the instructions to the letter and " MIRACL" Toshiba virtual store works perfectly.
I download all the applications without any problems.
But Youtube stil not working!
c'est dommage

As far as I know the YouTube changed its software architecture and therefore this app is not working.
But thanks for the commend regarding the virtual store update

Where do I get Toshiba Tools for Tecra A9 after HDD formatting?

Hello.
I've purchased a Tecra A9 notebook with Vista Business. I'd like to format it because there are a lot of tools and programms on it the notebook already that I do not need, and it's very slow.
There is a "hidden partition", but if I use that to recover it installs all the tools and software.
Luckily, there was a Vista Business DVD in the box.
So I would use that one.
Now my question: A few of the tools (Toshiba HDD-protection, Fingerprint-Software) seem useful and I'd like to reinstall them once it's all running again. Where can I download them? I did only find drivers on the Toshiba website.
Thank you very much!

Hello Daniel
Please do not be mad on me but you make it pretty complicated. If you want to optimize operating system you must not install it again. Leave preinstalled version. Preinstalled version is perfectly configured and all hardware components will work well.
All you must do is to remove Toshiba specific stuff that you do not want to use. Thats all!
I do this all the time. I use recovery DVD for OS installation but after finishing the first thing I do is to remove preinstalled Norton or disable autostart of all disturbing tools or utilities.
Before you reformat HDD try to make the same thing.

Toshiba 32RL938F: MP4 playback stopps after 2h 6min

Similar Messages

Maybe you are looking for