TOSHIBA f3507g cannot connect to 3G mobile broadband ( error code 0)

This is really a strange situation. Yesterday, I installed the lastest 3GRF POWER UTILITY and 3G F3507g drivers then inserted the 3G sim, my laptop could connect to internet (HSPA) normally but today when I download and install the lastest WIRELESS MANAGER software in other to check data and send sms but now my laptop cannot connect to 3G network although laptop still find the 3G signal. I also tested to send sms to my phone and it working but connect to 3G internet is impossible. I have tried to uninstall all the 3G driver and reinstall again but it not work. When I cheking troubleshooting, it said that " the mobile broadband network connection operation failed with error 0". I am using win7 and get the 3G driver from [http://aps2.toshiba-tro.de/wlan/] . Plz help me, thank you a lot !

In DUN, I give it a try and the error says: "The PPP link control protocol was terminated" when registering to internet.
In win7 connection manager, it 's in the same problem like WIRELESSS MANAGER
In manual profile, I set the following:
- Sim: no change
- Radio: automatic
- Profile: + APN: v-internet
+ Usernameand password: blank
+ DNS: automatic
+ IP: automatic
+ Authentical Protocols: check to NON, PAP, CHAP
- Network, Connection: automatic

Similar Messages

  • I cannot connect to itunes due to error code (-1202)

    I cannot connect to itunes due to error code (-1202) can anyoone help?

    Hi there bish bash,
    You may find the troubleshooting steps in the article below helpful.
    Can't connect to the iTunes Store
    http://support.apple.com/kb/ts1368
    -Griff W. 

  • Get error message when trying to sync iphone to puter that says"cannot connect because apple mobile divise is not started? what do i do?

    get error message when trying to sync iphone to puter that says"cannot connect because apple mobile divise is not started? what do i do?

    Restart your computer and the iPhone. Press & hold the Power and Home buttons together for 10+ seconds, ignoring the red power-off slider, until you see the Apple logo. It is safe to do, there should be no content loss. It is the same as rebooting your computer.

  • I can receive mail, but I cannot send mail, my mobile broadband is 3 and my server is BT

    I can receive mail, but I cannot send mail, my mobile broadband is 3 and my server is BT. I have been to the Apple Store today. They did not resove my problem. Can anybody help?

    Try this. Check the primary outgoing mail server username and password and make sure that they are in the settings even if it says that they are optional.
    Settings > Mail, Contacts, Calendars > select the account > account name , tap on SMTP (under the 'Outgoing Mail Server' heading) and then tap on your Primary Server and try entering your email account and password and see if you can then send emails.

  • App store on itunes not working error iTune cannot connect to itune store unknown error the network conection is refused on windows 8

    app store on itunes not working error iTune cannot connect to itune store unknown error the network conection is refused on windows 8

    Microsoft Windows 8 Business Edition (Build 9200)
    Hewlett-Packard HP Pavilion dv6 Notebook PC
    iTunes 11.1.5.5
    QuickTime not available
    FairPlay 2.5.16
    Apple Application Support 3.0.1
    iPod Updater Library 11.1f5
    CD Driver 2.2.3.0
    CD Driver DLL 2.1.3.1
    Apple Mobile Device 7.1.1.3
    Apple Mobile Device Driver 1.64.0.0
    Bonjour 3.0.0.10 (333.10)
    Gracenote SDK 1.9.6.502
    Gracenote MusicID 1.9.6.115
    Gracenote Submit 1.9.6.143
    Gracenote DSP 1.9.6.45
    iTunes Serial Number 0150B8980AD913B8
    Current user is not an administrator.
    The current local date and time is 2014-03-18 04:37:01.
    iTunes is not running in safe mode.
    WebKit accelerated compositing is enabled.
    HDCP is supported.
    Core Media is supported.
    **** External Plug-ins Information ****
    No external plug-ins installed.
    iPodService 11.1.5.5 is currently running.
    iTunesHelper is currently not running.
    Apple Mobile Device service 3.3.0.0 is currently running.
    **** Network Connectivity Tests ****
    Network Adapter Information
    Adapter Name:    {240FD97D-8118-4928-BF4E-8A531F89D837}
    Description:    Microsoft Wi-Fi Direct Virtual Adapter
    IP Address:    0.0.0.0
    Subnet Mask:    0.0.0.0
    Default Gateway:    0.0.0.0
    DHCP Enabled:    Yes
    DHCP Server:   
    Lease Obtained:    Wed Dec 31 16:00:00 1969
    Lease Expires:    Wed Dec 31 16:00:00 1969
    DNS Servers:   
    Adapter Name:    {BCD0EF3F-C4A4-402C-969A-C46C079E56A6}
    Description:    Bluetooth Device (Personal Area Network)
    IP Address:    0.0.0.0
    Subnet Mask:    0.0.0.0
    Default Gateway:    0.0.0.0
    DHCP Enabled:    Yes
    DHCP Server:   
    Lease Obtained:    Wed Dec 31 16:00:00 1969
    Lease Expires:    Wed Dec 31 16:00:00 1969
    DNS Servers:   
    Adapter Name:    {DD5C0797-BC23-4732-85FE-AC59C926EE98}
    Description:    Realtek PCIe GBE Family Controller
    IP Address:    10.144.120.70
    Subnet Mask:    255.255.255.0
    Default Gateway:    10.144.120.1
    DHCP Enabled:    Yes
    DHCP Server:    10.144.120.3
    Lease Obtained:    Tue Mar 18 03:26:26 2014
    Lease Expires:    Mon Jun 16 03:26:26 2014
    DNS Servers:    10.144.5.30
            10.144.130.5
    Adapter Name:    {E7CA4853-FF4A-49AE-AA4E-06BB1DEE67D4}
    Description:    Ralink RT5390 802.11b/g/n WiFi Adapter
    IP Address:    0.0.0.0
    Subnet Mask:    0.0.0.0
    Default Gateway:    0.0.0.0
    DHCP Enabled:    Yes
    DHCP Server:   
    Lease Obtained:    Wed Dec 31 16:00:00 1969
    Lease Expires:    Wed Dec 31 16:00:00 1969
    DNS Servers:   
    Active Connection:    LAN Connection
    Connected:    Yes
    Online:        Yes
    Using Modem:    No
    Using LAN:    Yes
    Using Proxy:    No
    Firewall Information
    Windows Firewall is on.
    iTunes is NOT enabled in Windows Firewall.
    Connection attempt to Apple web site was unsuccessful.
    The network connection timed out.
    Basic connection to the store failed.
    The network connection was refused.
    Connection attempt to Gracenote server was successful.
    The network connection was refused.
    iTunes has never successfully accessed the iTunes Store.
    **** CD/DVD Drive Tests ****
    No drivers in LowerFilters.
    UpperFilters: GEARAspiWDM (2.2.3.0),
    F: hp DVD-RAM UJ8B1, Rev H.02
    Drive is empty.

  • ITunes cannot connect to iPad because it is code blocked.

    iTunes cannot connect to iPad because it is code blocked.

    I have a iPad that is deaktivated - no code. Been advised via support to use iTunes to download and restore updated software. Have made several attempts but no go. iTunes cannot connect to the iPad because it is code blocked.

  • Cannot connect to the configuration database Error in HTTPS

    Hi
    We have a SharePoint 2010 farm ,with more then 20 web application  running . I am getting  "Cannot connect to the configuration database" error in one web application when   we browse through  https 
    The same application is working  fine when we  browse through http . I am  using AAM   i have 2 web server  which is been network load balanced  and the  https traffic  comes through F5
    Kindly help to resolve the issue 
    Prabakar

    HI Prabakar,Check the below URL that exactly related to the issue.
    http://expertsharepoint.blogspot.de/2014/05/cannot-connect-to-configuration-database.html
    Anil Avula[MCP,MCSE,MCSA,MCTS,MCITP,MCSM] See Me At: http://expertsharepoint.blogspot.de/

  • Cannot connect to olap service. Cannot connect to Essbase Server. Error:Essbase Error(1051293): Login fails due to invalid login credentials

    Hello All,
    I am getting following error, when trying to expand essbase from calculation manager, "Cannot connect to olap service. Cannot connect to Essbase Server. Error:Essbase Error(1051293): Login fails due to invalid login credentials",
    I am using EPM 11.1.2.1
    Thanks
    Yash

    If you have moved the server to a new data center and an issue has started occurring then it could point to the change.
    Are you able to log into essbase directly with Maxl using the same account?
    If you run a registry report do you see any of the configuration with IPs instead of DNS/hostname
    Cheers
    John
    http://john-goodwin.blogspot.com/

  • Error: Cannot connect to fulfillment server. Error: cannot find loan record.

    Error: Cannot connect to fulfillment server. Error: cannot find loan record. Definitely connected to internet, authorization correct, etc. Not sure what else to look at.

    Is the computer join the domain?
    Run the following command to check the automatic configuration is working
    Nslookup
    >set type=srv
    >_sipinternaltls._tcp.<sip domain>.com(for internal user)
    >_sip._tls<sip domain>.com(for external user)
    If you can ping to FE, please try to sign in with manual configuration.
    Lisa Zheng
    TechNet Community Support

  • Cannot connect to iTunes store unknown error(0x80090318)

    cannot connect to iTunes store unknown error(0x80090318)

    This solved my problem; maybe it would fix yours too: Uninstall iTunes 11 and all the applications that were installed with it. Afterwards, install iTunes 10 instead.
    Make sure to delete the library folder created by iTunes 11 in C:\Users\[username]\My Music\iTunes before launching the older versions of iTunes. Otherwise you would receive an error indicating that the programme cannot start.

  • App-v 4.6 The system cannot find the path specified. Error code: 4625DD4-07D0082C-00000003

    Below is our environment,
    App-v 4.6 SP2 Client installed on Windows Server 2008 R2 and managed with SCCM 2012 R2. 
    This server is part of Terminal Server Farm which contains two members.
    Only one user is getting the error when launching one application. It doesn't happen when he launches other applications
    The system cannot find the path specified.
    Error code: 4625DD4-07D0082C-00000003
    corrupt cp file detected ('Q:\AppName\osguard.cp'). osguard cp file, NO CORRECTIVE ACTION TAKEN
    I have renamed the Application's userdata in both roaming and local appdata.
    I have researched quite a bit about this and haven't anything solid. Most of the discussions suggest to clear the .fsd file and let the whole app layer re installed. 
    I am hesitant to do that as this is happening for only one user and for particular app.

    you can try to 'repair' the application: Ask the user to close all applications of that package, then use the App-V client MMC (sftcmc.msc) to locate the application entry. Right-click and 'repair'. This has to be done in the user's context/session
    Falko
    Twitter
    @kirk_tn   |   Blog
    kirxblog   |   Web
    kirx.org   |   Fireside
    appvbook.com

  • When i try to back up my iphone 4 it says i cannot back it up with the error code -50

    when i try to back up my iphone 4 it says i cannot back it up with the error code -50? HELP

    If you are running Windows and it stops on the first stage of a sync then my suggestion is to uninstall AppleDeviceSupport version 2.0.1 and re-install 1.5.2.
    There are instruction here to do it on Windows 7 (see the first post):
    https://discussions.apple.com/thread/3280228?tstart=0
    Those instructions are to fix a different problem, but it fixes the problem with syncing devices stopping on the first stage (backing up the device) too. The AppleDeviceSupport 2.0.1 comes with Quicktime 7.7 and, I believe, the latest Safari version.
    I'm running XP, so used the Everything search program (http://www.voidtools.com/download.php) to find the directories with the AppleDeviceSupport installers (they have the extension .msi and the version in the directory name) and right-mouse-buttoned them to do the uninstall and install. Note you need a reboot afterwards. (Actually I just sorted out the service in the Service Manager, but that's a longer explaination and a reboot works fine).
    Hope that helps,
    John

  • Cannot Modify Identity Management Realm : [LDAP: error code 20 - Attribute

    Hi ,
    I am new to the OID and now i am trying to Creating a New Identity Management Realm, i followed the steps of these followed URL
    http://www.oracle.com/technology/obe/obe_as_10g/im/realm_mng/realm.htm
    in step 12 it showing the following error
    Cannot Modify Identity Management Realm : [LDAP: error code 20 - Attribute
    Anyone please help me
    Thanks & Regards,
    Manoj                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                                       

    I was doing a terrible mistake.. Instead of using createSubcontext, i was using modifyAttributes to create an user. The Problem is resolved now. Here is the latest code
    try {
                   Hashtable env = new Hashtable();
                   env.put(Context.INITIAL_CONTEXT_FACTORY, "com.sun.jndi.ldap.LdapCtxFactory");
                   env.put(Context.SECURITY_AUTHENTICATION, "simple");
                   env.put(Context.SECURITY_PRINCIPAL, "cn=" + "Directory Manager");
                   env.put(Context.SECURITY_CREDENTIALS, "password");
                   env.put(Context.PROVIDER_URL, "ldap://localhost:389/dc=mytest,dc=com");
                   DirContext ctx = new InitialDirContext(env);
                   // Create attributes to be associated with the new context
                   Attributes attrs = new BasicAttributes(true); // case-ignore
                   Attribute sn = new BasicAttribute("sn");
                   sn.add("NewUser");
                   Attribute cn = new BasicAttribute("cn");
                   cn.add("NewUser");
                   Attribute objclass = new BasicAttribute("objectclass");
                   objclass.add("top");
                   objclass.add("inetOrgPerson");
                   attrs.put(objclass);
                   attrs.put(sn);
                   attrs.put(cn);
                   // Create the context
                   Context result = ctx.createSubcontext("cn=NewUser", attrs);
              } catch (Exception e) {
                   System.out.println("e is " + e);
              }

  • Cannot connect to Azure Mobile Services as DataSource

    I've created an Azure Mobile Service which is using .NET backend.
    Project Siena isn't able to connect or work against this kind of data source.
    Error message is
    An error occurred connecting to Azure Mobile Service
    I have also tried to create zz_config support table, and implement a custom TableController for serving the URI
    tables/zz_config but I could only got few steps further, still without the possibility to read and use the model exposed by Mobile Services
    This behavior has been reproduced with both Beta 2 and Beta 3
    P.S. Adding the AMS as REST data source makes possible to import and use the model exposed. The operation of association in this case must be done per-table in Siena
    Wheb can we expect Siena to work well together with the new version of Azure Mobile Services?
    Massimo Prota
    .NET MCAD - SP2007 MCTS - SP2010 MCPD and MCITP
    My blog: http://blogs.ugidotnet.org/mprota - Twitter:
    @massimoprota

    Yes, that article is indeed precise and updated. I followed all steps described properly, especially for the part about setting up the database structure, and create
    zz_config table (second post of the series)
    I can connect to AMS (JS Backend) with Siena, but tables' names aren't showing up correctly, but display as
    undefined, and from there on doesn't work properly.
    JSON object returned from GET /tables/zz_config?$filter=(Key%20eq%20'table') 
    "id": "ccb9c9a8-9bae-41c8-87aa-277e2e0d1379",
    "key": "table",
    "value": "users"
    I do confirm I have the same (incorrect) behavior using a .NET Backend where I set up
    zz_config table and create a TableController mapped with it; with route
    tables/zz_config
    I confirm also I had the same behavior this morning with Beta 2, before I installed Beta 3.
    P.S. The error message reported in my first post is returned only when the table
    zz_config isn't setup correctly on AMS
    Massimo Prota
    .NET MCAD - SP2007 MCTS - SP2010 MCPD and MCITP
    My blog: http://blogs.ugidotnet.org/mprota - Twitter:
    @massimoprota

  • Problem connecting Huawei E303 Mobile Broadband Dongle to MBP 2012

    I have just purchased the Huawei E303 USB Stick for my mobile broadband from Singapore's StarHub. According to the instruction sheet, the laptop should detect the USB automatically and the mobile broadband should install itself automatically. My MBP 2012 does not detect the USB drive so I can't install the mobile broadband. My MBP run Mountain Lion 10.8.2. Does anyone have the same problem? Do you think it's the problem with Huawei or Apple? I have seen many forum posts on this issue but no one seems to offer definite solutions.

    Just my personal experience : I just installed a E303 on my MacBookPro Retina 15" running 10.8.2.
    All went smoothly (took a bit of time) for the first time.
    I unplugged the modem and pluged it back a few minutes later, and the modem doesn't show anymore, and is not recognized by the previously installed software. LED status show booting.
    Then I tried on a recent macbook Air 13", 10.8.2 as well. modem is not seen either.
    This link may help as well :
    http://forums.macrumors.com/showthread.php?t=1458137
    Jean-David

Maybe you are looking for