Toshiba laptop won't boot in normal mode?

Few weeks ago, my laptop started to get slow and than when i restarted it on normal mode, only blank screen started to appear
with the cursor. It did work the next day but still it was really slow. and after couple of days of my computer getting slow, i reset/formatted my computer and it completely wiped out all of my files. I thought it would solve the problem, but after i logged
in the same thing happened. Help?? and it's working fine in safe mode..

They'll help you over here.
Windows forums on Microsoft Answers
Regards, Dave Patrick ....
Microsoft Certified Professional
Microsoft MVP [Windows]
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.

Similar Messages

My 27" imac won't boot in normal mode. The screen stays white. I have upgraded to Yosemite. However, the computer does boot in safe mode. Could this be a virus related issue or possibly a video card issue?

My 27" iMac will not boot in normal mode. The screen stays white. The computer will boot in safe mode. Could this be virus related or is it possibly an issue with my video card. Before this happened, my computer screen was flashing weird things and the computer would unexpectedly power down.

1. This procedure is a diagnostic test. It changes nothing, for better or worse, and therefore will not, in itself, solve the problem. But with the aid of the test results, the solution may take a few minutes, instead of hours or days.
Don't be put off by the complexity of these instructions. The process is much less complicated than the description. You do harder tasks with the computer all the time.
2. If you don't already have a current backup, back up all data before doing anything else. The backup is necessary on general principle, not because of anything in the test procedure. Backup is always a must, and when you're having any kind of trouble with the computer, you may be at higher than usual risk of losing data, whether you follow these instructions or not.
There are ways to back up a computer that isn't fully functional. Ask if you need guidance.
3. Below are instructions to run a UNIX shell script, a type of program. As I wrote above, it changes nothing. It doesn't send or receive any data on the network. All it does is to generate a human-readable report on the state of the computer. That report goes nowhere unless you choose to share it. If you prefer, you can act on it yourself without disclosing the contents to me or anyone else.
You should be wondering whether you can believe me, and whether it's safe to run a program at the behest of a stranger. In general, no, it's not safe and I don't encourage it.
In this case, however, there are a couple of ways for you to decide whether the program is safe without having to trust me. First, you can read it. Unlike an application that you download and click to run, it's transparent, so anyone with the necessary skill can verify what it does.
You may not be able to understand the script yourself. But variations of the script have been posted on this website thousands of times over a period of years. The site is hosted by Apple, which does not allow it to be used to distribute harmful software. Any one of the millions of registered users could have read the script and raised the alarm if it was harmful. Then I would not be here now and you would not be reading this message.
Nevertheless, if you can't satisfy yourself that these instructions are safe, don't follow them. Ask for other options.
4. Here's a summary of what you need to do, if you choose to proceed:
☞ Copy a line of text in this window to the Clipboard.
☞ Paste into the window of another application.
☞ Wait for the test to run. It usually takes a few minutes.
☞ Paste the results, which will have been copied automatically, back into a reply on this page.
The sequence is: copy, paste, wait, paste again. You don't need to copy a second time. Details follow.
5. You may have started the computer in "safe" mode. Preferably, these steps should be taken in “normal” mode, under the conditions in which the problem is reproduced. If the system is now in safe mode and works well enough in normal mode to run the test, restart as usual. If you can only test in safe mode, do that.
6. If you have more than one user, and the one affected by the problem is not an administrator, then please run the test twice: once while logged in as the affected user, and once as an administrator. The results may be different. The user that is created automatically on a new computer when you start it for the first time is an administrator. If you can't log in as an administrator, test as the affected user. Most personal Macs have only one user, and in that case this section doesn’t apply. Don't log in as root.
7. The script is a single long line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, though you may not see all of it in the browser window, and you can then copy it. If you try to select the line by dragging across the part you can see, you won't get all of it.
Triple-click anywhere in the line of text below on this page to select it:
PATH=/usr/bin:/bin:/usr/sbin:/sbin:/usr/libexec;clear;cd;p=(Software Hardware Memory Diagnostics Power FireWire Thunderbolt USB Fonts SerialATA 4 1000 25 5120 KiB/s 1024 85 \\b%% 20480 1 MB/s 25000 ports ' com.clark.\* \*dropbox \*genieo\* \*GoogleDr\* \*k.AutoCAD\* \*k.Maya\* vidinst\* ' DYLD_INSERT_LIBRARIES\ DYLD_LIBRARY_PATH -86 "` route -n get default|awk '/e:/{print $2}' `" 25 N\\/A down up 102400 25600 recvfrom sendto CFBundleIdentifier 25 25 25 1000 MB ' com.adobe.AAM.Updater-1.0 com.adobe.CS4ServiceManager com.adobe.CS5ServiceManager com.adobe.fpsaud com.adobe.SwitchBoard com.apple.AirPortBaseStationAgent com.apple.FolderActions.enabled com.apple.FolderActions.folders com.apple.installer.osmessagetracing com.apple.mrt.uiagent com.apple.ReportCrash.Self com.apple.SafariNotificationAgent com.apple.usbmuxd com.google.keystone.agent com.google.keystone.daemon com.microsoft.office.licensing.helper com.oracle.java.Helper-Tool com.oracle.java.JavaUpdateHelper ' ' 879294308 3627668074 1083382502 1274181950 1855907737 464843899 3694147963 1417519526 1233118628 2456546649 2806998573 2636415542 842973933 3301885676 891055588 998894468 695903914 1443423563 ' 51 5120 files );N5=${#p[@]};p[N5]=` networksetup -listnetworkserviceorder|awk ' NR>1 { sub(/^$[0-9]+$ /,"");n=$0;getline;} $NF=="'${p[26]}')" { sub(/.$/,"",$NF);print n;exit;} ' `;f=('\n%s: %s\n' '\n%s\n\n%s\n' '\nRAM details\n%s\n' %s\ %s '%s\n-\t%s\n' );S0() { echo ' { q=$NF+0;$NF="";u=$(NF-1);$(NF-1)="";gsub(/^ +| +$/,"");if(q>='${p[$1]}') printf("%s (UID %s) is using %s '${p[$2]}'",$0,u,q);} ';};s=(' s/[0-9A-Za-z._]+@[0-9A-Za-z.]+\.[0-9A-Za-z]{2,4}/EMAIL/g;/faceb/s/(at\.)[^.]+/\1NAME/g;/\/Shared/!s/(\/Users\/)[^ /]+/\1USER/g;s/[-0-9A-Fa-f]{22,}/UUID/g;' ' s/^ +//;/de: S|[nst]:/p;' ' {sub(/^ +/,"")};/er:/;/y:/&&$2<'${p[10]} ' 1s/://;3,6d;/[my].+:/d;s/^ {4}//;H;${ g;s/\n$//;/s: [^EO]|x([^08]|02[^F]|8[^0])/p;} ' ' 5h;6{ H;g;/P/!p;} ' ' ($1~/^Cy/&&$3>'${p[11]}')||($1~/^Cond/&&$2!~/^N/) ' ' /:$/{ N;/:.+:/d;s/ *://;b0'$'\n'' };/^ *(V.+ [0N]|Man).+ /{ s/ 0x.... //;s/[()]//g;s/(.+: )(.+)/ (\2)/;H;};$b0'$'\n'' d;:0'$'\n'' x;s/\n\n//;/Apple[ ,]|Genesy|Intel|SMSC/d;s/\n.*//;/\)$/p;' ' s/^.*C/C/;H;${ g;/No th|pms/!p;} ' '/= [^GO]/p' '{$1=""};1' ' /Of/!{ s/^.+is |\.//g;p;} ' ' $0&&!/ / { n++;print;} END { if(n<10) print "com.apple.";} ' ' sub(/ :/,"");{ print|"tail -n'${p[12]}'";} ' ' NR==2&&$4<='${p[13]}' { print $4;} ' ' END { $2/=256;if($2>='${p[15]}') print int($2) } ' ' NR!=13{next};{sub(/[+-]$/,"",$NF)};'"`S0 21 22`" 'NR!=2{next}'"`S0 37 17`" ' NR!=5||$8!~/[RW]/{next};{ $(NF-1)=$1;$NF=int($NF/10000000);for(i=1;i<=3;i++){$i="";$(NF-1-i)="";};};'"`S0 19 20`" 's:^:/:p' '/\.kext\/(Contents\/)?Info\.plist$/p' 's/^.{52}(.+) <.+/\1/p' ' /Launch[AD].+\.plist$/ { n++;print;} END { if(n<200) print "/System/";} ' '/\.xpc\/(Contents\/)?Info\.plist$/p' ' NR>1&&!/0x|\.[0-9]+$|com\.apple\.launchctl\.(Aqua|Background|System)$/ { print $3;} ' ' /\.(framew|lproj)|\):/d;/plist:|:.+(Mach|scrip)/s/:[^:]+//p ' '/^root$/p' ' !/\/Contents\/.+\/Contents|Applic|Autom|Frameworks/&&/Lib.+\/Info.plist$/ { n++;print;} END { if(n<1100) print "/System/";} ' '/^\/usr\/lib\/.+dylib$/p' ' /Temp|emac/{next};/(etc|Preferences|Launch[AD].+)\// { sub(".(/private)?","");n++;print;} END { split("'"${p[41]}"'",b);split("'"${p[42]}"'",c);for(i in b) print b[i]".plist\t"c[i];if(n<500) print "Launch";} ' ' /\/(Contents\/.+\/Contents|Frameworks)\/|\.wdgt\/.+\.([bw]|plu)/d;p;' 's/\/(Contents\/)?Info.plist$//;p' ' { gsub("^| |\n","\\|\\|kMDItem'${p[35]}'=");sub("^...."," ") };1 ' p '{print $3"\t"$1}' 's/\'$'\t''.+//p' 's/1/On/p' '/Prox.+: [^0]/p' '$2>'${p[43]}'{$2=$2-1;print}' ' BEGIN { i="'${p[26]}'";M1='${p[16]}';M2='${p[18]}';M3='${p[31]}';M4='${p[32]}';} !/^A/{next};/%/ { getline;if($5<M1) a="user "$2"%, system "$4"%";} /disk0/&&$4>M2 { b=$3" ops/s, "$4" blocks/s";} $2==i { if(c) { d=$3+$4+$5+$6;next;};if($4>M3||$6>M4) c=int($4/1024)" in, "int($6/1024)" out";} END { if(a) print "CPU: "a;if(b) print "I/O: "b;if(c) print "Net: "c" (KiB/s)";if(d) print "Net errors: "d" packets/s";} ' ' /r\[0\] /&&$NF!~/^1(0|72\.(1[6-9]|2[0-9]|3[0-1])|92\.168)\./ { print $NF;exit;} ' ' !/^T/ { printf "(static)";exit;} ' '/apsd|BKAg|OpenD/!s/:.+//p' ' (/k:/&&$3!~/(255\.){3}0/ )||(/v6:/&&$2!~/A/ ) ' ' $1~"lR"&&$2<='${p[25]}';$1~"li"&&$3!~"wpa2";' ' BEGIN { FS=":";p="uniq -c|sed -E '"'s/ +\$[0-9]+\$\$.+\$/\\\2 x\\\1/;s/x1$//'"'";} { n=split($3,a,".");sub(/_2[01].+/,"",$3);print $2" "$3" "a[n]$1|p;b=b$1;} END { close(p);if(b) print("\n\t* Code injection");} ' ' NR!=4{next} {$NF/=10240} '"`S0 27 14`" ' END { if($3~/[0-9]/)print$3;} ' ' BEGIN { L='${p[36]}';} !/^[[:space:]]*(#.*)?$/ { l++;if(l<=L) f=f"\n "$0;} END { F=FILENAME;if(!F) exit;if(!f) f="\n [N/A]";"cksum "F|getline C;split(C, A);C="checksum "A[1];"file -b "F|getline T;if(T!~/^(AS.+ (En.+ )?text(, with v.+)?$|(Bo|PO).+ sh.+ text ex|XM)/) F=F" ("T", "C")";else F=F" ("C")";printf("\nContents of %s\n%s\n",F,f);if(l>L) printf("\n ...and %s more line(s)\n",l-L);} ' ' s/^ ?n...://p;s/^ ?p...:/-'$'\t''/p;' 's/0/Off/p' ' END{print NR} ' ' /id: N|te: Y/{i++} END{print i} ' ' / / { print "'"${p[28]}"'";exit;};1;' '/ en/!s/\.//p' ' NR!=13{next};{sub(/[+-M]$/,"",$NF)};'"`S0 39 40`" ' $10~/$L/&&$9!~"localhost" { sub(/.+:/,"",$9);print $1": "$9;} ' '/^ +r/s/.+"(.+)".+/\1/p' 's/(.+\.wdgt)\/(Contents\/)?Info\.plist$/\1/p' 's/^.+\/(.+)\.wdgt$/\1/p' ' /l: /{ /DVD/d;s/.+: //;b0'$'\n'' };/s: /{ /V/d;s/^ */- /;H;};$b0'$'\n'' d;:0'$'\n'' x;/APPLE [^:]+$/d;p;' ' /^find: /d;p;' "`S0 44 45`" ' BEGIN{FS="= "} /Path/{print $2} ' ' /^ *$/d;s/^ */ /;' ' s/^.+ |\(.+$$//g;p ' '/\.appex\/Contents\/Info\.plist$/p' ' /2/{print "WARN"};/4/{print "CRITICAL"};' );c1=(system_profiler pmset\ -g nvram fdesetup find syslog df vm_stat sar ps sudo\ crontab sudo\ iotop top pkgutil 'PlistBuddy 2>&1 -c "Print' whoami cksum kextstat launchctl sudo\ launchctl crontab 'sudo defaults read' stat lsbom mdfind ' for i in ${p[24]};do ${c1[18]} ${c2[27]} $i;done;' defaults\ read scutil sudo\ dtrace sudo\ profiles sed\ -En awk /S*/*/P*/*/*/C*/*/airport networksetup mdutil sudo\ lsof test osascript\ -e sysctl\ -n pluginkit );c2=(com.apple.loginwindow\ LoginHook '" /L*/P*/loginw*' "'tell app \"System Events\" to get properties of login items'|tr , \\\n" 'L*/Ca*/com.ap*.Saf*/E*/* -d 1 -name In*t -exec '"${c1[14]}"' :CFBundleDisplayName" {} \;|sort|uniq' '~ $TMPDIR.. $ -flags +sappnd,schg,uappnd,uchg -o ! -user $UID -o ! -perm -600 $' '.??* -path .Trash -prune -o -type d -name *.app -print -prune' :${p[35]}\" :Label\" '{/,}L*/{Con,Pref}* -type f ! -size 0 -name *.plist -exec plutil -s {} \;' "-f'%N: %l' Desktop L*/Keyc*" therm sysload boot-args status " -F '\$Time \$(RefProc): \$Message' -k Sender kernel -k Message Req 'bad |Beac|caug|corru|dead[^bl]|FAIL|fail|GPU |hfs: Ru|inval|jnl:|last value [1-9]|n Cause: -|NVDA$|pagin|proc: t|Roamed|rror|ssert|Thrott|tim(ed? ?|ing )o|WARN' -k Message Rne 'Goog|ksadm|Roame|SMC:|suhel| VALI|ver-r|xpma' -o -o -k Sender fseventsd -k Message Req SL -o -k Sender Req launchd -k Message Req de: " '-du -n DEV -n EDEV 1 10' 'acrx -o comm,ruid,%cpu' '-t1 10 1' '-f -pfc /var/db/r*/com.apple.*.{BS,Bas,Es,J,OSXU,Rem,up}*.bom' '{/,}L*/Lo*/Diag* -type f -regex .\*[cght] ! -name .?\* ! -name \*ag \( -exec grep -lq "^Thread c" {} \; -exec printf \* \; -o -true $ -execdir stat -f:%Sc:%N -t%F {} \;|sort -t: -k2 |tail -n'${p[38]} '/S*/*/Ca*/*xpc* >&- ||echo No' '-L /{S*/,}L*/StartupItems -type f -exec file {} +' '-L /S*/L*/{C*/Sec*A,Ex}* {/,}L*/{A*d,Ca*/*/Ex,Co{mpon,reM},Ex,In{p,ter},iTu*/*P,Keyb,Mail/B,Pr*P,Qu*T,Scripti,Sec,Servi,Spo,Widg}* -path \\*s/Resources -prune -o -type f -name Info.plist' '/usr/lib -type f -name *.dylib' `awk "${s[31]}"<<<${p[23]}` "/e*/{auto,{cron,fs}tab,hosts,{[lp],sy}*.conf,mach_i*/*,pam.d/*,ssh{,d}_config,*.local} {,/usr/local}/etc/periodic/*/* /L*/P*{,/*}/com.a*.{Bo,sec*.ap}*t {/S*/,/,}L*/Lau*/*t .launchd.conf" list getenv /Library/Preferences/com.apple.alf\ globalstate --proxy '-n get default' -I --dns -getdnsservers\ "${p[N5]}" -getinfo\ "${p[N5]}" -P -m\ / '' -n1 '-R -l1 -n1 -o prt -stats command,uid,prt' '--regexp --only-files --files com.apple.pkg.*|sort|uniq' -kl -l -s\ / '-R -l1 -n1 -o mem -stats command,uid,mem' '+c0 -i4TCP:0-1023' com.apple.dashboard\ layer-gadgets '-d /L*/Mana*/$USER&&echo On' '-app Safari WebKitDNSPrefetchingEnabled' "+c0 -l|awk '{print(\$1,\$3)}'|sort|uniq -c|sort -n|tail -1|awk '{print(\$2,\$3,\$1)}'" -m 'L*/{Con*/*/Data/L*/,}Pref* -type f -size 0c -name *.plist.???????|wc -l' kern.memorystatus_vm_pressure_level );N1=${#c2[@]};for j in {0..9};do c2[N1+j]=SP${p[j]}DataType;done;N2=${#c2[@]};for j in 0 1;do c2[N2+j]="-n ' syscall::'${p[33+j]}':return { @out[execname,uid]=sum(arg0) } tick-10sec { trunc(@out,1);exit(0);} '";done;l=(Restricted\ files Hidden\ apps 'Elapsed time (s)' POST Battery Safari\ extensions Bad\ plists 'High file counts' User Heat System\ load boot\ args FileVault Diagnostic\ reports Log 'Free space (MiB)' 'Swap (MiB)' Activity 'CPU per process' Login\ hook 'I/O per process' Mach\ ports kexts Daemons Agents XPC\ cache Startup\ items Admin\ access Root\ access Bundles dylibs Apps Font\ issues Inserted\ dylibs Firewall Proxies DNS TCP/IP Wi-Fi Profiles Root\ crontab User\ crontab 'Global login items' 'User login items' Spotlight Memory Listeners Widgets Parental\ Controls Prefetching SATA Descriptors App\ extensions Lockfiles Memory\ pressure );N3=${#l[@]};for i in 0 1 2;do l[N3+i]=${p[5+i]};done;N4=${#l[@]};for j in 0 1;do l[N4+j]="Current ${p[29+j]}stream data";done;A0() { id -G|grep -qw 80;v[1]=$?;((v[1]==0))&&sudo true;v[2]=$?;v[3]=`date +%s`;clear >&-;date '+Start time: %T %D%n';};for i in 0 1;do eval ' A'$((1+i))'() { v=` eval "${c1[$1]} ${c2[$2]}"|'${c1[30+i]}' "${s[$3]}" `;[[ "$v" ]];};A'$((3+i))'() { v=` while read i;do [[ "$i" ]]&&eval "${c1[$1]} ${c2[$2]}" \"$i\"|'${c1[30+i]}' "${s[$3]}";done<<<"${v[$4]}" `;[[ "$v" ]];};A'$((5+i))'() { v=` while read i;do '${c1[30+i]}' "${s[$1]}" "$i";done<<<"${v[$2]}" `;[[ "$v" ]];};';done;A7(){ v=$((`date +%s`-v[3]));};B2(){ v[$1]="$v";};for i in 0 1;do eval ' B'$i'() { v=;((v['$((i+1))']==0))||{ v=No;false;};};B'$((3+i))'() { v[$2]=`'${c1[30+i]}' "${s[$3]}"<<<"${v[$1]}"`;} ';done;B5(){ v[$1]="${v[$1]}"$'\n'"${v[$2]}";};B6() { v=` paste -d: <(printf "${v[$1]}") <(printf "${v[$2]}")|awk -F: ' {printf("'"${f[$3]}"'",$1,$2)} ' `;};B7(){ v=`grep -Fv "${v[$1]}"<<<"$v"`;};C0() { [[ "$v" ]]&&sed -E "$s"<<<"$v";};C1() { [[ "$v" ]]&&printf "${f[$1]}" "${l[$2]}" "$v"|sed -E "$s";};C2() { v=`echo $v`;[[ "$v" != 0 ]]&&C1 0 $1;};C3() { v=`sed -E "${s[63]}"<<<"$v"`&&C1 1 $1;};for i in 1 2;do for j in 0 2 3;do eval D$i$j'(){ A'$i' $1 $2 $3; C'$j' $4;};';done;done;{ A0;D20 0 $((N1+1)) 2;D10 0 $N1 1;B0;C2 27;B0&&! B1&&C2 28;D12 15 37 25 8;A1 0 $((N1+2)) 3;C0;D13 0 $((N1+3)) 4 3;D23 0 $((N1+4)) 5 4;D13 0 $((N1+9)) 59 50;for i in 0 1 2;do D13 0 $((N1+5+i)) 6 $((N3+i));done;D13 1 10 7 9;D13 1 11 8 10;D22 2 12 9 11;D12 3 13 10 12;D23 4 19 44 13;D23 5 14 12 14;D22 6 36 13 15;D22 38 52 66 54;D22 7 37 14 16;D23 8 15 38 17;D22 9 16 16 18;B1&&{ D22 35 49 61 51;D22 11 17 17 20;for i in 0 1;do D22 28 $((N2+i)) 45 $((N4+i));done;};D22 12 44 54 45;D22 12 39 15 21;A1 13 40 18;B2 4;B3 4 0 19;A3 14 6 32 0;B4 0 5 11;A1 17 41 20;B7 5;C3 22;B4 4 6 21;A3 14 7 32 6;B4 0 7 11;B3 4 0 22;A3 14 6 32 0;B4 0 8 11;B5 7 8;B1&&{ A2 19 26 23;B7 7;C3 23;};A2 18 26 23;B7 7;C3 24;D13 4 21 24 26;B4 4 12 26;B3 4 13 27;A1 4 22 29;B7 12;B2 14;A4 14 6 52 14;B2 15;B6 14 15 4;B3 0 0 30;C3 29;A1 4 23 27;B7 13;C3 30;B3 4 0 65;A3 14 6 32 0;B4 0 16 11;A1 39 50 64;B7 16;C3 52;D13 24 24 32 31;D13 25 37 32 33;A2 23 18 28;B2 16;A2 16 25 33;B7 16;B3 0 0 34;B2 21;A6 47 21&&C0;B1&&{ D13 21 0 32 19;D13 10 42 32 40;D22 29 35 46 39;};D23 14 1 62 42;D12 34 43 53 44;D12 22 20 32 25;D22 0 $((N1+8)) 51 32;D13 4 8 41 6;D12 26 28 35 34;D13 27 29 36 35;A2 27 32 39&&{ B2 19;A2 33 33 40;B2 20;B6 19 20 3;};C2 36;D23 33 34 42 37;B1&&D23 35 45 55 46;D23 32 31 43 38;D12 36 47 32 48;D13 20 42 32 41;D13 37 2 48 43;D13 4 5 32 1;D13 4 3 60 5;D12 26 48 49 49;B3 4 22 57;A1 26 46 56;B7 22;B3 0 0 58;C3 47;D22 4 4 50 0;D12 4 51 32 53;D23 22 9 37 7;A7;C2 2;} 2>/dev/null|pbcopy;exit 2>&-
Copy the selected text to the Clipboard by pressing the key combination command-C.
8. Launch the built-in Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Click anywhere in the Terminal window and paste by pressing command-V. The text you pasted should vanish immediately. If it doesn't, press the return key.
9. If you see an error message in the Terminal window such as "Syntax error" or "Event not found," enter
exec bash
and press return. Then paste the script again.
10. If you're logged in as an administrator, you'll be prompted for your login password. Nothing will be displayed when you type it. You will not see the usual dots in place of typed characters. Make sure caps lock is off. Type carefully and then press return. You may get a one-time warning to be careful. If you make three failed attempts to enter the password, the test will run anyway, but it will produce less information. In most cases, the difference is not important. If you don't know the password, or if you prefer not to enter it, press the key combination control-C or just press return three times at the password prompt. Again, the script will still run.
If you're not logged in as an administrator, you won't be prompted for a password. The test will still run. It just won't do anything that requires administrator privileges.
11. The test may take a few minutes to run, depending on how many files you have and the speed of the computer. A computer that's abnormally slow may take longer to run the test. While it's running, there will be nothing in the Terminal window and no indication of progress. Wait for the line
[Process completed]
to appear. If you don't see it within half an hour or so, the test probably won't complete in a reasonable time. In that case, close the Terminal window and report what happened. No harm will be done.
12. When the test is complete, quit Terminal. The results will have been copied to the Clipboard automatically. They are not shown in the Terminal window. Please don't copy anything from there. All you have to do is start a reply to this comment and then paste by pressing command-V again.
At the top of the results, there will be a line that begins with the words "Start time." If you don't see that, but instead see a mass of gibberish, you didn't wait for the "Process completed" message to appear in the Terminal window. Please wait for it and try again.
If any private information, such as your name or email address, appears in the results, anonymize it before posting. Usually that won't be necessary.
13. When you post the results, you might see an error message on the web page: "You have included content in your post that is not permitted," or "You are not authorized to post." That's a bug in the forum software. Please post the test results on Pastebin, then post a link here to the page you created.
14. This is a public forum, and others may give you advice based on the results of the test. They speak only for themselves, and I don't necessarily agree with them.
Copyright © 2014 by Linc Davis. As the sole author of this work, I reserve all rights to it except as provided in the Use Agreement for the Apple Support Communities website ("ASC"). Readers of ASC may copy it for their own personal use. Neither the whole nor any part may be redistributed.

IMac G5 won't boot in normal and safe mode, but will from single-user mode

Hello everyone,
I'm quite new here, so I try to do my best if you have a question.
Yesterday, someone nearby me had a iMac G5 (Powermac8,1), and he sayd, that the computer sometimes will boot, sometimes not.
I did test it, I thought it was running fine, but when I played some music in iTunes, it was stuck on 9 seconds, and crashed (with a kernel panic). The guy also sayd, that there was nothing important on the computer, so a clean install was fine.
Now, the problem is, that it will not boot in normal mode (without anything pressed on boot), also it won't in safe mode (shift-boot), but it will, when I enter single-user mode, mount the hard drive and exit from single-user mode so it will go futher on booting. Sometimes it will not, and immediately gives you a kernel panic in single-user mode, but it will 90 percent of the time.
Then you've got another problem: when it's running in the normal desktop from single-user mode, it'll be stuck after some time again. If I look into the Kernel Panic file created, most times it's because of Spotlight indexing, so I disabled that.
He also gave me the disks (Apple Hardware Test and Extra Applications, and iMac G5 Mac OS X Install Disks 1-3) that came with the Mac. He sayd that I could use them, but I think he didn't test out the SuperDrive, because when I insert a disk, it will try to read, but it will make 2 same sounds, and quits after 10 tries, when it will spit the cd out. Also normal (audio) disks.
Also, I must hurry with the commands for mounting and exiting in single-user mode, or it will just not boot.
In all cases, after 30-45 seconds from pressing the power button, the fan will start blowing at full speed, and it will stop after the exit command in Single-user mode. That's weird.
I can't do anything with the SuperDrive, I can't normally boot in Mac OS X except for Single-user mode (but I don't think he would like to do that every time the computer boots up), and I have very limited time when Mac OS X arrived on the desktop.
When booting in Verbose mode, it will be stuck on this:
AppleSMU::PMU vers = 0x000d004c, SPU vers = 0x15, SDB vers = 0x01,
(and sometimes ends with a kernel crash by fsck_hfs)
Things I've tried (without any success):
- /sbin/fsck -fy (in single-user mode)
- Disabling Spotlight and mds
If you want some more information, feel free to ask!
Greetings
-MrYoranimo
PS: My main language is Dutch, so my English can be bad at some points.

Thank you for your support! This reply is a little bit late, because I was to the camping this weekend.
The only thing I sure do know, is that the iMac has a bad SuperDrive. That's one problem, but I don't really wanna use it, and you fix everything by Single-user mode and when I get to the desktop to test things and change stuff in the Preference Panes.
What also came to my mind was that there also is a problem with the videocard (driver), because sometimes when I boot into Single-user mode, I can see some white pixels which aren't supposed to be there. And when booting from SUM you can see that some of the colors are different and there are weird patterns on the screen.
I also tried to setup a NetBoot server on this computer (MacBook Mid 2010) with just Lion 10.7.4 on it, but I'm not that expert and I didn't really find the good posts on the Internet, although I tried it with the Server applications and both Server applications and DeployStudio. But I didn't succeed.
I don't really like buying a new FireWire hard disk or external FireWire dvd reader/writer, except if it has USB support, because my MacBook doesn't support FireWire, and I really wanna make use of it then.
If I know more or have fixed it, I will surely post again here with what I did to fix it (if no one else has posted here already ).

MacBook Pro won't start in normal mode and won't open in safe mode.

My Mac suddenly won't open in normal mode. It just stays on the apple logo and won't continue. Then, I tried going on Safe Mode. Unfortunately, it only loads up to the Apple Logo with the progress bar below it. I would load one-third the bar and shut down completely. What do I do?

Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu.
Reinstall Lion, Mountain Lion, or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

Laptop won't boot beyond the screen showing "Tobshiba leading innovation"

I installed an antivirus recently and in its scan some viruses were found. Those viruses were deleted and now my laptop wont boot into windows. It just stays where "toshiba" logo is displayed. My laptop is running on windows 8.1. I have a recovery DVD, but the laptop won't boot from the DVD either. Is there a way to get my laptop to boot windows without doing a factory reset. Please help!!

Try the Troubleshooting Assistant or the suggestions in this article.
What can I do if my Windows 8 laptop won't start?
- Peter

MacBook Pro Retina 15" mid-2012 won't boot in clamshell mode with an external display attached

I have a 15" MBPr mid-2012 running OS X 10.10.1. The system won't boot in clamshell mode (power is connected, lid shut) with an external display attached via an Apple Thunderbolt->DVI adapter. it boots fine if the lid is open. It isn't the adapter or the display since my 15" MBPr mid-2014 boots up just fine connected to the same adapter and monitor. And this system used to boot like this just fine some while ago (probably before it was upgraded to Yosemite). I've reset the NVRAM (twice) to no avail.
Has anyone encounter this? Anyone have a solution? Should I try an SMC reset (always a bit nervous about that)? Might it be a driver issue in Yosemite?
Thanks.

I have a 15" MBPr mid-2012 running OS X 10.10.1. The system won't boot in clamshell mode (power is connected, lid shut) with an external display attached via an Apple Thunderbolt->DVI adapter. it boots fine if the lid is open. It isn't the adapter or the display since my 15" MBPr mid-2014 boots up just fine connected to the same adapter and monitor. And this system used to boot like this just fine some while ago (probably before it was upgraded to Yosemite). I've reset the NVRAM (twice) to no avail.
Has anyone encounter this? Anyone have a solution? Should I try an SMC reset (always a bit nervous about that)? Might it be a driver issue in Yosemite?
Thanks.

Hp laptop won't boot up

My daughters laptop won't boot up the automatic repaire screen comes on then just goes off and try's to reboot on loop won't do anything

@Neilco15 ,
Hello and thank you for posting on the HP support forums.
Firs thing you will want to check for is any blinking LEDs on your system.
Here is a link to check out.
Troubleshooting LED Blink Codes or Beep Codes During Startup or Boot
Please post back with any results.
Thank you again for posting and have a great day.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

HP laptop won't boot at all

My one and half year old Hp 2000 laptop won't boot at all. When I press the power button, it doesn't show any sign of life at all.
I have tried Hard test several times yet it didn't fix it.
Battery charges, power adapter working.
I have also tried to boot using the AC adapter alone yet my precious laptop isn't showing any sign of life.
Please how do I fix this? I need to do my assignment and prepare for my exams, and I can't afford a new laptop. Not when the current laptop is pretty new.
Please help me HP support.
Thank you in advance.

Hi @Chichiiii ,
Thank You for your inquiry.
I understand that when you power on your notebook it is unresponsive. You did state that the AC adapter is working and the battery is charging.
Here is a link to HP Notebook PCs - Computer Does Not Start (Windows 8), which has multiple links to help you determine the issue.
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

Mdworker deny mach-lookup. But macbook won't boot in safe mode

I have a common problem, I get theese messages every now and then in console:
2/8/13 6:38:24.000 PM kernel[0]: Sandbox: sandboxd(793) deny mach-lookup com.apple.coresymbolicationd
2/8/13 6:38:24.534 PM sandboxd[793]: ([791]) mdworker(791) deny mach-lookup com.apple.ls.boxd
2/8/13 6:38:24.556 PM sandboxd[793]: ([792]) mdworker(792) deny mach-lookup com.apple.ls.boxd
There is a solution, which should resolve it, like here https://discussions.apple.com/message/19750564?searchText=mach-lookup%20com.appl e.ls.boxd#19750564
I have just boot in safe mode. (holding Shift during boot)
but my macbook won't boot in Safe mode. It just freeses with a grey screen for hours and wont boot.
I tried to leave it overnight to boot, but it didn't.
Please help me make my macbook to boot in SafeMode.
my configuration is the following:
MacBookPro8,1
OSX 10.8.2

There is a bug in fsck_hfs that is affecting a bunch of people. Basically as your comptuer starts in safe mode, it runs a file system check (fsck) against your hard drive, it gets to a certain point and... just sits there. No one knows why outside of apple.
Lots of info here, including a way to get around it by tricking the system to think fsck had been run, though the fsck will not be complete so it is not a good solution.
https://discussions.apple.com/message/21389737?ac_cid=tw123456#21389737

Windows server 2008 r2 operating system not booting in normal mode after unstalled the virus gaurd

Windows server 2008 r2 operating system is not booting in normal mode after i uninstalled the virus guard in the system. I tried to repair the system but repairing option not available in server 2008. i can log in to the system only safe mode.
Please help me to solve this issue as soon as possible .I do not have the any system backup with me .

Hi,
Regarding the issue here, please restart the computer and press F8 until you see the
advanced boot options, select start windows normally,
if it starts with no problem, please check if you have the option boot from safe mode checked:
run->type msconfig->tab boot->boot options, check if the
safe boot is selected, if yes please uncheck it. Then restart the computer to check if this problem still exists.
If the system needs repair, please take a look into the below WIKI article, and check the event viewer to see if any errors for further troubleshooting.:
Windows Server 2008 Repair Steps for No Boot Issues
http://social.technet.microsoft.com/wiki/contents/articles/4162.windows-server-2008-repair-steps-for-no-boot-issues.aspx
Hope this helps
Best regards
Michael
If you have any feedback on our support, please click
here.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Yosemite install won't boot into any mode

Really sorry if this has been covered before but I spent a good time searching and couldn't find any existing posts with symptoms to the same extent.
I've got a 2008 iMac 27" and have the latest version of Yosemite installed (10.10.1 I guess). I upgraded to Yosemite probably 2-3 weeks ago and everything has been fine. Then yesterday when I woke it up from sleep it effectively froze - no mouse or keyboard input. So I did a reset by holding down the power button, and when I turned it back on it went to the apple logo boot screen with a progress bar that gets to just below 50% and stuck there. I've restarted quite a few times and left it running up to six hours and still it doesn't boot.
Now this is similar to the issue here - OSX Yosemite won't boot after install on mid 2010 iMac - except I am unable to boot into any mode, and the only startup keys accepted are the P-RAM reset. It won't boot into recovery mode (command+R), safe mode (Shift), startup drive select mode (Option), diagnostics mode (D)... nothing
I've booked into a Genius Bar appointment when the Apple stores reopen after Christmas, but I'm hoping that is a last resort and to be honest I'm unsure what they can do for me except to say it's a lost cause.
Are there any suggestions on what could be happening and why it's ignoring the startup modes? I would have suggested the keyboard not being recognised except the P-RAM command works perfectly, so it's obviously seeing it. I'm a little scared that because it won't let me into a boot device menu (which must operate independent of any HDD) then there's an issue ahead of that in the boot sequence, so possibly the motherboard is shot...
Sorry if I seem a little desperate. I had a HDD crash two years ago to the day (great Christmas present Apple) and it kind of puts a dampener on things.
Happy holidays and I'm grateful for any help that anyone can offer

Hello there, semerton.
Great job on troubleshooting the issue on your own so far. The following Knowledge Base aritcle offers some additional steps to try for resolving your issue:
Mac OS X: Gray screen appears during startup - Apple Support
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

My laptop won't boot and caps lock blinking continuously (1blink in 4 sec.)

Sir,
Today morning I turned on laptop but laptop won't boot and wireless button glowing continuously and also caps lock blinking continuously as 1 blink per 4 sec.

do you mean 1 blink repeating and then a pause and 1 blink repeating again? The diagnostics show that as a CPU not functional issue.http://support.hp.com/us-en/product/HP-Pavilion-15-Notebook-PC-series/6529948/model/6622489/document/c01732674#AbT2 Try a hard reset.Follow the instructions at the following web page.http://support.hp.com/us-en/product/HP-Pavilion-15-n209tx-Notebook-PC-(ENERGY-STAR)/6529948/model/6622489/document/c01684768 If a hard reset does not help, then contact HP for warranty service. Is your notebook still in warranty?Check your warranty status Here.

My laptop won't boot-up,won't let me get to the boot menu . can anyone help me,please.

Laptop won't boot-up,won't bootmenu.

Hi Willrobb1,
I understand your computer will not boot up. Restart your computer and keep press F9 to open the "Boot Menu" or "Boot Device Options". Press Enter to continue.
Here is a document on system restore if you need it. You can restore it to a previous point when it was working correctly.
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&dlc=en&docname=c01835735&lc=en&product=5218386&tmp...
Hope it helps.
Thanks
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Laptop won't boot; Black screen w/moveable cursor

Satellite A305-S6905
Current Situation: Laptop won’t boot-up; black screen with moveable mouse cursor, HHD indicator actively flashing.
I was attempting to upgrade from Vista to Win7-32bit-Ultimate. Kept receiving error messages regarding non-compatible files. Next the computer would not recognize the Multi-Drive (did not appear on the My Computer screen. Now all I get is the black screen. How can I restore?

BTW, to reboot this PC (Windows 7), all you need to do is pres ctr+alt+delete at the black screen, and it will do just that. But if you disconnected all usb drives, then you cannot use this shortcut. You need to just shut it down with the power button.

Laptop won't boot 10

So my Asus laptop won't boot up Windows 10 and I've tried to "Refresh" it but it won't work. It worked once after I installed it but I couldn't even access the App Store. Help!

Hi,
What is your current situation?
If Windows 10 has low performance on your laptop, you may take a check at the system requirements :
System requirements
You may alos contact the manufacturer and see if they could offer any further help.
For the current situation, you may consider install Windows 10 using Virtual Machine:
Step-By-Step: Creating and Running A Windows 10 VM on Windows 8.1
Best regards
Michael Shao
TechNet Community Support

Toshiba laptop won't boot in normal mode?

Similar Messages

Maybe you are looking for