Toshiba Tecra M1 - Won't reboot

Hello @ll
This is my first post on this forum. I write from poland, so forgive me for my poor english.
I have a problem with my old laptop (Toshiba Tecra M1). Computer won't reboot. After the Arch installation everything was fine, command init 6 was working correctly. When I was doing installs and configurations (adds daemon's to rc.conf, modifying fstab, install KDEmod etc.) i was rebooting system to see how it works. I don't know when, but after 3th, maybe 4th reboot system won't boot. I can see the screen which contains information about closing daemons, but after this listing I can see only black screen, computer stops and nothing happens.
Thanks for any advices
Last edited by pmd (2008-08-14 11:59:16)

On this virtual way nobody can say for sure what the problem is. As Joe already wrote it is hardware related issue and it should be checked by technicians. Fact is that this Tecra M1 is pretty old notebook model (I had it 8 years ago) so I think repair is not a option.

Similar Messages

Toshiba Tecra A8 won't boot

My Toshiba A8 PTA83A-04F012 notebook will not boot. When I boot the machine, I get the normal Toshiba splash screen then the screen goes blanks with a blinking cursor in the upper left hand corner. Apart from the CPU fan kicking in, nothing else happens. I've tried to boot from an alternative devices (eg CD-ROM) but the same thing happens. I’ve even tried to get into the bios (setup) but it ignores my request. The keyboard seems to function normally. Please help. Tony

Sounds like it could be ram, try it with only one ram strip at a time, also did you install any software recently that could be not working correctly? Does it work in safe mode? Also in the bios see if the computer is reading the hard drive correctly, or maybe you changed a setting in the bios and need to use the default setings Detailed specs if you need them from toshiba http://www.csd.toshiba.com/cgi-bin/tais/support/jsp/modelContent.jsp?ct=SB&os=&category=&moid=160275...
sorry for all the questions, I want your machine to work

After installing Maverick on my Macbook it won't reboot

After installing Maverick on my Macbook it won't reboot. It fully downloaded and intalled fine and once it had finished intalling, a pop up message said that my macbook with restart in 10 seconds. i restarted my macbook but it never did anything more than have a grey screen with the apple symbol and a spinning wheel underneath that.
I have tried starting in safe mode (holding down shift), ive tried holding down command, option, R and P but that didnt work, I have tried holdig down command and R and that didnt work. Holding down option when turning on did work but when i go into disk utility and i try to verify and repair disk of my 250GB Toshiba MK2555GSXF Media i get a warning saying "Live File system repair is not supported"

Hi,
On the iOS devices remove the Apple ID.
Set the device in to Airplane Mode (this breaks with the server)
Start with the iPhone to add back the Apple ID - only after you see the iPhone Number is Verified.
The Restart the Mac Version
Accept the pops ups that state what the iPhone is using.
Do same on iPad.
8:31 pm Wednesday; April 2, 2014
 iMac 2.5Ghz i5 2011 (Mavericks 10.9)
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb (Snow Leopard 10.6.8)
 Mac OS X (10.6.8),
 Couple of iPhones and an iPad

S10 X86 installation hangs on Toshiba Tecra M2 Laptop

Hello,
I am trying to install s10_X86 on toshiba tecra M2 laptop. But it hangs at secondary boot loader. Checked the HCl too from the bigadmin and it supports s10 3/05. I have the same media. Can any body help me install the os the laptop.
Thanks in Advance,
Regards,
Raghu

I too installed s10 on a Tecra M2, and have disabled legacy USB FDD support. This enabled me to get past installation problem, but at first reboot, the system hangs at checking ufs file systems. It hangs at:
" [sytem/filesystem/autofs:default failed repeatedly (see 'svcs -x' for details) ] "
This is a dual boot system, with XP on first part of disk, and s10 installed on last 17gb of disk
Thanks...Kier

Toshiba tecra a11-17c refusing to boot from LAN

Hello
I am working on a Toshiba tecra a11-17c. We currently have about 18 of the same laptop and the person who originally built the computers has left the office we are currently working at.
The issue I am have is that I want to boot the computer from lan and do a windows 7 installation on the laptop but I keep getting the error "Media test failure, check cable"
I know the cable is working because I was able to build a Toshiba satellite pro l20 perfectly fine
The other Toshiba tecra a11-17c laptops have the same issue when trying to rebuild them too
I am fully able to log into a Toshiba tecra a11-17c and connect to the internet via the same network cable and port when in windows.
I have also tried to swap the hard drive with a different tecra a11-17c but it just kept getting a blue screen as soon as the windows flag appeared.
I then tried a format of the hard drive and a reset to default of the bios settings as suggested in a different forum.
I then tried to clone a fully working hard drive from a different fully working tecra a11-17c and it just dose the blue screen as stated above.
I then used an old windows XP recovery disk for the tecra a11-17c it did the build fine no issues then when it came to build to windows but as stated above it just dose a blue screen the same as windows 7.
Now I have no idea what to do but to believe it is something Toshiba has done with the tecra a11-17c range because its the same issue for all 18 of the tecra a11-17c laptops I have here.
Any way I am at a loss and have no idea what to do it seems to be something as simple as the network card need to be turned on during the boot phase but I can not find anything in the bios.

I'm sorry but I have no experience doing what your attempting to do. However, for your information, this site is for U.S. models only and I would suggest you also post in the appropriate regional Toshiba Support forum to get better suggestions. Good luck
L305-S5955, T9300 Intel Core 2 Duo, 4GB RAM, 60GB SSD, Win 7 Ultimate 64-bit

CPU Upgrade on Toshiba Tecra M3

Hi,
I just finished refurbishing my Toshiba Tecra M3 (64MB Nvidia 6200 model) which had been dead for 6 months. Basically it had the mainboard changed (applied new daimond thermal grease over GPU/CPU due to overheating issue), new screen installed, new 160GB Samsung 5400 HDD and body plastics refursbished too and at present its working like a charm and as new condition inside out. The system currently holds a Pentium M 750 CPU (1.86GHZ) and I'm aware that such models supports up to 2.13GHZ. I have tried to replace the CPU with a 2.0GHZ Pentium M 760 SL7SM model however upon boot up, laptop powers up fine to bios but pwoers down soon after. Any idea's what the issue may be? The BIOS has been upgraded to 1.50 (latest version)
Thanks for any help.
Clive Cordina MC.P MCS.A MCS.E
Regards
Clive Cordina
MC.P, MCS.A, MCS.E

Hi again, just managed to solve the issue by myself. I have resetted the mainboard from the bottom (aside VGA heatsink), reinstalled again latest version of BIOS i.e 1.50 and now I can run my Tecra M3 on a 2.26GHZ CPU (Pentium M 780).
P.S Currently averaging a 60deg temp CPU at high usage. Not that bad for the BBQ warrior.
Clive.
Regards
Clive Cordina
MC.P, MCS.A, MCS.E

Help! My Mac mini won't reboot

Hi. I posted yesterday (in the Safari forum) concerning a problem I was having with Safari 3.0.4 after updating to 10.4.11. Basically, it wouldn't run. Anyway, I did a bunch of searches on the Web (including this forum) to try to figure out what to do. One piece of advice was to move System/Library/Frameworks/ApplicationServices.frameworkapplicationservices.fram ework to the desktop.
Well, I did that, and things started acting weird. I tried to copy it back, but the process just seemed to hang. So, I did what I thought was obvious but was apparently a bad idea: I rebooted. Guess what--now my Mac won't reboot. I just get a perpetual hourglass.
I tried doing repairs with Disk Utility, but that didn't fix the problem. I also did a superfluous Hardware Check from the same OS disk, and that turned out normal.
So, what's the solution? A visit to my friendly Apple dealer for some service? Or am I just permanently hosed with no recourse? Please let me know what I can do. Thanks!

Sadly Apple stores are rarely set up for the purpose of completing backups and securing data, so that's not something you can rely on them to do. Some Apple approved service providers are better equipped for doing this, but in the end, it's not a good (or comfortable) proposition to trust your data to anyone else, and the more important that data, the less good, (or comfortable) it is if you have to.
The risk of data loss is relatively small in this situation - particularly if you ran 'repair disk' from disk utility and it reported no errors. That generally would indicate the drive is healthy and there are no indications of damaged data or file structures. Still there is always a risk!
In your situation, if I were faced with the knowledge that I was going to be buying an external drive for future backups, I'd be inclined to buy it now (selecting a firewire-connected hard drive of at least the same, if not much larger capacity than the internal), and then run Disk Utility again, this time (carefully) selecting the external drive, partitioning it under the Apple scheme, then formatting it (MacOS Extended (journaled) and then installing MacOS on it from your 10.3 installer. After that, I'd boot to it by holding down the option key during startup, then selecting the external drive from the list that (after a couple of minutes) should appear. Then the internal drive will be mounted on the desktop under the external which has booted the system. That will give you to option to copy your iPhoto and iTunes libraries to the external drive, and thus secure your data.
Once that's done, you can reboot to the install disk and basically even erase and install, because your data is safe on the external drive!
After the internal is set up again, and fully updated, it then becomes a simple matter of moving your data back to it, and then erasing the external once more, and setting up your backups with SuperDuper! or CCC.
It might sound like a bit of messing about, but that would keep your data safe in your own hands!

MacBook Pro won't reboot. Get spinning circle even after hard drive replaced at Apple Store

MacBook Pro won't reboot. Have to reinstall OSX each time I shut down in order to get it to start up. What could be wrong? I had the hard drive replaced already.

You shouldn't be using the disc at all. I thought I had made that clear. Boot from your recovery partition and run Disc Utility. If you get the same result -- the internal drive can't be repaired -- then you should consider replacing it. No storage device can be trusted, in my opinion, after throwing an error like that. But whether you choose to replace it or erase it, you have to get the data out first.
There are several ways to back up a Mac that is unable to fully boot. You need an external hard drive to hold the backup data.
1. Boot from your recovery partition (10.7 or later), a local Time Machine backup volume (10.7.2 or later), or your installation disc (10.6.8 or earlier.) Launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
How to back up and restore your files
2. If you have a working Mac, and both it and the non-working Mac have FireWire ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive.
How to use and troubleshoot FireWire target disk mode
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.

The screen on my iPhone 4s is not working it's just black & won't reboot?

The screen on my iPhone 4s is not working it's just black & won't reboot?

Try the suggestions here to see if they resolve your problem:
http://support.apple.com/kb/ts1559
If these don't work you probably have a hardware problem. Visit an Apple store for an evaluation or contact Apple Support.

MSI Z87I Won't Reboot or Shut DOwn

My new system won't shut down or reboot from the OS (Ubuntu 14.04) or from the BIOS settings, i.e. Settings -> Save & Exit -> Save Changes and Reboot will not reboot the system. All my peripherals will turn off, but the fans stay on and the only way to power off the system is to long-hold the power switch on the front of the case or turn off the power at the PSU.
There is ONE case in which the system will reboot. If I go to Settings -> Save & Exit, choose "Restore Defaults" and then select "Save Changes and Reboot," the system will reboot one time, but it won't reboot or shut down after this.
I'm already on my second MoBo since I thought it was a MoBo issue.
Specs:
SSD: Patriot Pyro 60GB
Memory: 2x PNY 4GBH2X02E99927-16-H
CPU: Intel Core i3-4150 LGA1150
PSU: Thermaltake TR2 500W
I've tried reseating the MoBo as well as testing it outside of the case with no luck.

Quote from: rusty.carruth on 10-January-15, 07:52:22
Ah, thanks! Got it.
It looks to me like that is a different link to the same program, as when I downloaded it I got 'MSIHQ Tool 1.25g Installer(1).rar' as the filename, since I had just downloaded 'MSIHQ Tool 1.25g Installer.rar' from the link I posted (or perhaps from a page pointed to by that page, I've already forgotten where I got it...)
I notice that the '180' file has a batch file that runs 'fpt'. Am I supposed to run that batch file, or run 'efiflash bios.bin'? (Or both if this is the first time I've flashed the motherboard)
Quote
It looks to me like that is a different link to the same program, as when I downloaded it I got 'MSIHQ Tool 1.25g Installer(1).rar' as the filename, since I had just downloaded 'MSIHQ Tool 1.25g Installer.rar' from the link I posted (or perhaps from a page pointed to by that page, I've already forgotten where I got it...)
em nope, its the same program. (1) is auto renamed because the same name was already existing in your download folder
Quote from: rusty.carruth on 10-January-15, 07:52:22
I notice that the '180' file has a batch file that runs 'fpt'. Am I supposed to run that batch file, or run 'efiflash bios.bin'? (Or both if this is the first time I've flashed the motherboard)
no need to run anything
just let the tool to prepare the USB key then boot from it
when this menu appear select option 2:
1 Run Memtest
2 Proceed with BIOS Update
3 Flash back to prevision bios
then press any key after read some safety instructions
then when asked if you want to Run Memtestx86, answer with "N"
then flash will start and will be asked for reboot when its done
you no need to type or run anything manually, its tottaly automated

My Torch 9800 won't reboot

I have tried several times to reboot my Torch and it won't reboot. I have removed the battery but the reboot only goes a short way then stops. What else can I do?

Have you recently upgraded or downloaded any application to the device?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Older mac mini won't reboot from Install DVD?

I've passed on my 2006 era mac mini to my daughter. We can't seem to get to a factory settings because it won't reboot from the install DVD. It keeps cycling through to the normal reboot.

Could be damaged disks.
BestBuy sells disk repair kits.
But for about the same price as disk repair kit, you could call 1-800-676-2775 and give them the unit serial number and pay shipping/handling fee for replacement.
Assuming it is bad disks.

Clustered Oracle VM server 2.1.2 won't reboot or hangs

Has anyone experience with clustered Oracle VM servers 2.1.2 seem to be hang or won't reboot until the server is power reset?
Every time I reboot the master pool server, the server seems to be hung or won't reboot. To solve this problem I have to power reset the server or reboot the other server in the server pool or vice versa. This is not what I wanted. What do i need to do to have a smooth reboot of master server pool without reboot the other server in the server pool?
Thank you in advance.

Hi Avi,
There is no entries logged after issuing the reboot command on ovm-s-2 or ovm-s-1.
SSH session #1
[root@ovm-s-2 network-scripts]# reboot
It hangs right here
SSH session #2
[root@ovm-s-2 ~]# tail -100 /var/log/messages
Apr 16 12:03:54 ovm-s-2 shutdown[5694]: shutting down for system reboot
Apr 16 12:03:54 ovm-s-2 init: Switching to runlevel: 6
Apr 16 12:06:35 ovm-s-2 ntpd[2675]: synchronized to LOCAL(0), stratum 10
Apr 16 12:07:40 ovm-s-2 ntpd[2675]: synchronized to 72.18.205.156, stratum 2
Apr 16 12:13:02 ovm-s-2 ntpd[2675]: synchronized to 4.79.132.217, stratum 2
[root@ovm-s-2 ~]#
# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 3.0G 738M 2.1G 27% /
/dev/sda1 99M 36M 58M 39% /boot
tmpfs 293M 0 293M 0% /dev/shm
/dev/sdb1 3.0G 738M 2.1G 27% /OVS
The /OVS should not be still mounted. If it does, it should be like this, right?
FROM ovm-s-1 the master server pool.
[root@ovm-s-1 ~]# df -h
Filesystem Size Used Avail Use% Mounted on
/dev/sda2 3.0G 741M 2.1G 27% /
/dev/sda1 99M 36M 58M 39% /boot
tmpfs 293M 0 293M 0% /dev/shm
/dev/sdb1 954G 1.1G 953G 1% /OVS

Solaris 7/8 on Toshiba Tecra 8000 Laptop - Possible?

This could be an easy one or one that has to go to Toshiba but I've been trying to get Solaris 7 loaded onto a Toshiba tecra 8000 laptop and can't get a 'fit' for the screen size. I've looked on the tested h/w list and can't see it listed so just wondered if anyone has used this platform for Solaris 7 and what they used? It's a 1024x768 screen. Any help appreciated.

I added Xig's Accelerated X server. With it I use 1024x768 screen and desktop
though I have also played with a larger virtual desktop at same resolution.

Solaris 8 and PCMCIA on Toshiba Tecra 520 CDT

I am having problems with my pcmcia services with X86 on my Toshiba Tecra 520 CDT laptop. It will not recognize the network card(s) or any PCMCIA cards for that matter. Do I need to load a specific driver or turn on the PCMCIA service or something to that affect for the PCMCIA slot to work? I have heard that the Toshiba laptop is the most supported laptop model for X86. Could anyone give me some advice or point me to the right website or news group. Please reply or contact me directly at [email protected] Much appreciation!

I believe that PCMCIA is broken in Solaris 8.
I can't seem to get networking to work on my Dell either.
Good Luck,
Mike

Toshiba Tecra M1 - Won't reboot

Similar Messages

Maybe you are looking for