Touchpad, Mouse, USB not working

On 7/09/15 an HP update did not install items. Mouse and touchpad as well as usb stopped working. Mouse is Bluetooth. Drivers won't install. Touchpad drivers were reinstalled and did not work. Usb ports won't recognize anything plugged into them and won't install any drivers. Tried dinstalling chipset and it didn't work. Tried uninstalling all usb drivers but this didn't correct the issue .Tried changing ease of access to use the keypad to control the cursor but that doesn't work. Could a settings change have done this? I keep getting a notification for a split second saying settings were changed . Any help would be appreciated.

Hi! I know this is a very old post and forum theme (the hp 6220 is a bit old...) but i have one and it works fine after i changed the motherboard and i make it run with windows 7 , the wireless driver was so difficult to make it work but i succeeded, its ok now.
My problem is the touchpad, it dosen't works at all...nothing?! In device manager it says working properly but dosent. Is there something to do to configure or something like that while i replaced the whole motherboard. The cables are ok, its connected to the right connector and the touchpad was working on the old motherboard. If you could give me some advice / trick or something to make it work. Thanks in advance!
(HP Compaq NC6220, 1,86 Ghz Intel pentium M750, 2 Gb Ram DDR2, Intel Graphics, 40 Gb Hdd, Windows 7 32-bit)

Similar Messages

  • Hp 2000 laptop touchpad mouse will not work

    I have had this laptop approx a year and no problems. The other day I went to log online and the mouse worked to get to the icon but after that it freezes. I have reset my computer several times and ran my anti virus but I keep getting the same result. I have used this computer maybe 20 times since I have had it. Please help me. Also there is an orange light on that is next to the touch pad that stays on, that is new.

    Hi there ,
    Thank you for visiting the HP Support Forums and Welcome! This is a great site to get answers and ask questions. I have looked into the issue you are having with your touchpad mouse. Have you tried plugging in an external mouse? First thing I want to address is the orange LED that is next to the touchpad. The orange LED indicated on the touchpad has been turned off. You can turn it back on by double tapping the corner of the touchpad where the LED is (usually top left corner). Here is a document that has some troubleshooting steps, shows you the LED area, and how to turn it on/off. To test if it is hardware or software please follow these steps below: Boot into safe mode by tapping F8 at start up, and see if you are still having the problem. This should tell us if it’s the hardware or software. After a while in safe mode if you don't have the problem open command prompt and run the following command SFC /scannow. This should correct any software errors. Here is a link to get to command prompt. Please re-post with the results of these troubleshooting steps and your Model Number (How Do I Find My Model Number or Product Number?) Thanks! 

  • E420 - Touchpad & Mouse Stick Not Working

    I removed the the keyword now the touchpad & trackpoint stick won't work.
    Thanks a lot
    Chris

    Hardware not detected in Device Manager. The connection ribbons are tight. Hmmm.....
    Thanks a lot
    Chris

  • Touchpad mouse scroll not working in newer versions of Firefox

    Firefox doesn't seem to like to play nice with touchpad mice on laptops when it comes to scrolling. I am running Windows 7 on an HP G60-535DX with FF 6. I noticed the scroll issue when I bought this computer and was using FF 5 but it seems the problem started with FF 4. I have searched for fixes for this and tried everything that looked promising. I uninstalled my mouse drivers and re-installed them. Everything is up to date. I don't know what else to do. I am in love with the new tab group feature and I don't want to have to switch to Google Chrome.... Help?

    Does Firefox use another font instead?
    If this is the case then which font?
    You can use this extension to see which fonts are used for selected text.
    *fontinfo: https://addons.mozilla.org/firefox/addon/fontinfo/

  • My laptop touchpad left mouse key not working

    I have a Elitebook 8440p with windows 7 professional.The touchpad left mouse key not working ,but right mouse key works well.my driver is  synaptics 14.0.10 090ct09 and the touchpad name is synapticsTouchPadV7.2.
    thanks in advance.
    wy

    i had the same problem. what solved this for me was to simply go to device manager and under mice and other pointing devices uninstall the touchpad, i had a usb mouse handy just in case i needed it, but then i restarted the laptop and it auto reinstalled touchpad for me and then all options worked on startup.

  • USB mouse does not work

    hi All
    I bought a new HP laptop few days ago,when I installed Win7 pro on it after a few minutes, the usb mouse stopped working. Its light still lights up ,but the cursor does not react. The drivers of the device are installed and working properly. the mouse will
    not work until I click "scan for hardware changes"in Device Management . but when I restart the computer, it happend again . but win7 home edition seems does not have this problem. please help.  thanks  

    Hi,
    I suggest updating the latest BIOS and chipset from HP site, then reinstalling USB controllers to check the result. If any USB hub is used, please bypass it.
    http://blogs.technet.com/b/asiasupp/archive/2010/11/23/error-message-one-of-the-usb-device-attached-to-this-computer-has-malfunctioned-and-windows-does-not-recognise-it.aspx
    Also, please perform
    clean boot, disable your antivirus and firewall
    temporarily to avoid any blocking. If the issue persists in clean boot, test the issue in Safe Mode and Device Clean boot.
    Device Clean Boot
    1. Go to Device Manager
    2. Expand "Sound, video and game controllers".
    3. Right Click on Audio device and choose disable.
    4. Please use the same method to disable other dubious hardware such as: internal modem, and CD-R drive. Please note some devices such as video adapter are not available
    to be disabled.
    5. After that, restart the computer and then test the issue. If it does not occur, you can enable the device one by one to narrow down this issue.
    After you found the device that causing the problem, you can resolve by installing last driver or replacing the device.
    Best Regards,
    Niki
    Please remember to click "Mark as Answer" on the post that helps you, and to click "Unmark as Answer" if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

  • USB port Working for my Wireless mouse but not working for another Devices like Flash Memory ?, USB port Working for my Wireless mouse but not working for another Devices like Flash Memory ?

    USB port Working for my Wireless mouse but not working for another Devices like Flash Memory ? Anyone can help me plz?

    Hi, is this a question" Post?
    or are you just offering an insight into your Mouse Issue?
    Generally and at times we all have little idiosyncrasies appearing with the running of our Macs.
    I use the same Logitech BT with my MBP. MB & iBook..(not at the same time) Only ever had one issue
    and the cure was to completely Delete the mouse from BT -> Repair Permissions & Reboot then Re Install the BT mouse..Ihave just put a new set of batteries in the Logitech (only 2nd set ever)...L

  • External mouse scrolling not working

    The scrolling function of my external mouse does not work when the MacBook Pro is not plugged in with its powercord. The mouse buttons seem to be functioning.  So does as an external keyboard. My wife has the same problem (using 10.6.2 OS). There are no options in the System Preferences that deal with this. Is this just an oversight by Apple? This basically makes using an external keyboard and mouse a nonviable option for a laptop unless you are near an electric outlet. If you know of a workaround I would appreciate the information. If not, it is something Apple will have to correct as it a pretty obvious oversight.
    Thanks in advance for any advice.
    Tony

    Check your settings when it is unplugged to make sure they are still properly configured.  You might even want to try and disable the trackpad when a mouse is being used.  I would also check out USB Overdrive (Shareware).

  • My wireless keyboard and mouse do not work on my All-In-One computer?

    Q.: My wireless keyboard and mouse do not work on my All-In-One computer?
    A.: If your wireless keyboard and mouse do not work even after changing the batteries, please try re-syncing them by following these steps.
    1. Make sure the computer is on, plug in the USB receiver. Push the button on the USB receiver until it flashes blue.
    2. While the receiver is still flashing, press the red connect button on the keyboard (Make sure the batteries are installed). The USB receiver should stop flashing after pressing the button on the keyboard. It may take up to 8 seconds to sync.
    3. Repeat the same process for the mouse. Push the button on the USB receiver, then press the connect button on the mouse (Make sure the mouse is on).
    Note: This applies to all MSI All-In-One computers that include the ES500W wireless keyboard and SW130 mouse.

    "This machine has an added 4 USB ports, could this be causing a problem?
    It definitely could be the source of the problem. Perhaps the PCI card was bumped loose during shipping?
    Have you tried removing the card? That's where I would start.
    Keep us posted.

  • Mouse is not working properly on a one month old HP Pavillion 15-NO28US

    I'm sure it's already been talked about on here, but I haven't found a successful fix or the same exact problem as I'm having. I went thru the latest Windows 8.1 update recently (at least I think it was the update) and when I restarted my computer yesterday the mouse was not working properly. Like a lot of other people who are complaining about it, the two-finger scrolling and other similar features are not working, but what really bothers me is the the mouse is almost acting like it was changed to a left handed mouse. I've checked the settings and it is still set on right-handed, but when I click the left mouse button the small window opens up next to where I clicked, which has the copy, delete and paste options (and other regular options) in it. When I click the right mouse button, nothing happens. Double tapping on the touchpad doesn't do anything either. I downloaded and install the latest synaptic drivers and nothing happened. I even performed a system recovery last night to reset all setting and it's still not working. This really sucks because I've only had this computer for about a month and I've already lost everything I've put on it...most importantly all of my school work and music apps. Is there anything to fix this or can anyone tell me what's going on with this stuff, before I have to call into HP and have a melt down?

    Hi Kevin3047,
    Thank you for your query, I will do my best to assist you!!
    I understand that after updating from Windows 8 to 8.1 your mouse is not performing correctly. You have tried the built in troubleshooter but to no avail.
    You checked the settings and they appear ok, but when you click the left mouse button the small window opens up next to where you  clicked, which has the copy, delete and paste options (and other regular options) in it. When you click the right mouse button, nothing happens. Double tapping on the touchpad doesn't do anything either. I grasp that you did a recovery but it did not help.  You also stated you lost your data once, and that in itself is extremely aggravating, I agree.
    Here is a step that may help.
    Go to the Command Prompt and right click on it to run as Administrator
    type sfc /scannow and press enter.  This will scan for corrupted files and try to repair them.
    Here are links to two documents that may aid with this process.
    Troubleshooting Mouse Problems (Windows 8)
    Using and Troubleshooting the TouchPad or ClickPad (Windows 8)
    Would you also please try a clean boot to see if it persists. Here is  a Windows document to assist you.
    How to perform a clean boot in Windows
    If none of this has alleviated the issue, I suggest you do a  Refresh Your PC to Resolve Problems (Windows 8).
    If the issue still pesists, I would do a recovery again.  You will be prompted during the recovery to backup your personal files to prevent data loss. I would suggest you choose yes, to prevent data loss.
    Performing an HP System Recovery (Windows 8)
    Restoring Files that were Backed Up Using HP Recovery Manager (Windows 8)
    This will take it back to factory. Here is a document on Updating Windows 8 to 8.1 to assist you with doing the update again.
    If you are still experiencing the issue, as @visruth stated I would contact HP support for assistance.  They are able to remotely log onto your system to help with this difficulty.
    Please call HP technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region HP Technical Support Sitemap.
    Good Luck!!
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • PS/2 Mouse does not work anymore

    I was playing Halo on WinXP and I had to switch my wireless mouse with a wired mouse because I was not getting a good response out of it. When I wanted to switch back the mouse did not work. I tried a number of different mice and none of them work. If I use a USB mouse it will work in the USB port. This causes a problem for when I am running Linux on my machine.
    My question is, are there any known problems with the PS/2 mouse port on the SIS 645DX Chipset board (645E Max Series).
    OR
    Has anybody had a similar problem to this?
    I searched the posts but there were quite a few on this board. Too many even after I filtered out junk.
    Thanks a bunch guys.

    Well it turns out that I needed to reboot with the mouse plugged in. That was an easy fix. I can't believe I didn't do that.
    Side note, Why do you say it is bad for me to have the receiver on the top of the computer? Is there some interferenece?
    Thanks for the help.
    Roderic J

  • Installing windows 8 with bootcamp 5. Have to make a choice at personalize but mouse is not working.  What can I do?

    installing windows 8 with bootcamp 5. Have to make a choice at personalize but mouse is not working.  What can I do?

    I solved my problem by using a USB mouse and a USB keyboard instead of bluetooth

  • Left mouse controls not working... very strange

    I don't believe this is unique to R40 so any help would be appreciated 
    I have just installed new hard drive and now the left track point and ultranav left mouse does not work. If I go to
    mouse>ultranav> settings> buttons> left click  and select jump to start it works until standby power off or logon screen. So
    again it works until any of the above and then I need a usb mouse to re enable the left mouse control. I do not believe it is a
    hardware issue as all 3 left click methods will work until standby etc. i have re-installed latest drivers and am now considering a
    reinstall of Windows XP.
    Any suggestions???
    R40 2723

    Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance/Themes).
    *Don't make any changes on the Safe mode start window.
    *https://support.mozilla.org/kb/Safe+Mode
    *https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

  • Just downloaded Yosemite and now the swipe feature on my mouse does not work. Why?

    Just downloaded the new OS onto my iMAC and now the "swipe" feature on my mouse does not work, i.e. I can't go back and forth between web  pages.  Is this a function of the new OS?

    What kind of mouse do you have? USB? Have you tried to plug it in - try all the USB ports (maybe there is a problem with one). It should automatically detect it.

  • Portg R500 - Blue Screen and keyboard mouse are not working

    Hi All,
    I am using windows XP, well I was not any more due to below problem.
    Laptop blue screened and now any time it goes to windows xp screen blue screen comes and reboot the system. Its not working in safe mode at all. Keyboard any mouse are not working. I cannot even go to BIOS.
    I tried to plug a USB keyboard but still its same. I cannot even boot from CD.
    Please could some one advise what do I need to do in order to resolve the problem.
    Thanks in advance.
    Nysoh

    Hey,
    How you can test it in safe mode if keyboard doesnt work? I mean before Windows starts you have to press F8 key and then go down to select safe mode. Therefore you need the keyboard
    In your case I would try to remove the battery and AC/DC adapter for at least one hour. Then connect both devices again and make sure battery is fully charged. Start your notebook and try accessing the BIOS setup and load the default settings.
    If Windows doesnt start you have to do a recovery installation I think. Some Windows files might be muddled up

Maybe you are looking for