TouchSmart 520 Windows 7 Home premium Problems after critical updates

After my TouchSmart 520 auto ran critical updates on 13 Feb 2013,I cannot connect to Internet at all.It was still able to connect to my home wireless network.
I did a systerm recovery, to restore up to just before the critical updates on 13 Feb, then it's able to connect to internet. After that, it auto ran critical updates 2 times, and the same problem started.I have done the system recovery again and now turn off the downloading and installation of critical updates completely, but this should not be long term solution.
Has anyone encounter same problem or is able to help me on this? What else do I need to do?
Appreicate any help.TIA!

Hello sgcosimo,
You’re not able to connect to the internet after updates have run. I’ve had that happen before and usually Microsoft will send out an update that fixes the problem a few days later.
You can try to run the updates again to see if you still get the error.
If you’re still not able to get online, go into device manger and uninstall the Wi-Fi adapter and restart the computer.
Here is a link to uninstall the adapter.
Let me know if this helps.

Similar Messages

Can I change the OS of Touchsmart 610 from Windows Home Premium to Windows 7 Pro?

I have 610 1100me system loaded with Windows Home Premium 64 bit. We bought it from Dubai and is in use in Pakistan. It started giving problems after few weeks of use. Its' hard disk makes noise and sometimes, system could not find boot disk. Most of the times blue screen of death and hanging issues. Any idea about this issue and how to fix it? My observation is that the culprit is hard disk!
Also, can I change its OS to Windows 7 Pro or ultimate (32 or 64 bit)? Where can I find all drivers for Pro or Ultimate?
Many thanks for your valueable advice.
Regards,
KK
This question was solved.
View Solution.

Hi,
Nearly nothing change interms of drivers required for Windows 7 (HP, Pro, Ultimate) unless you switch from 64 to 32 bit. You can reuse your current HP 64 bit drivers for 64 bit W7 Pro or Ultimate.
Regards,
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Bluetooth software license file - HP Touchsmart IQ772 Vista Home Premium SP1

I installed Driver Max a couple of weeks ago and updated outdated drivers, blutooth amongst them, identified by Driver Max, on my HP Touchsmart IQ772, Vista Home Premium SP1. Since last week, I get this message every time I log on or restart my computer; Bluetooth Software license file not found. [2]. What does this mean and how do I stop this happening again?
Thanks.
This question was solved.
View Solution.

I had the same problem after doing a registry clean-up on my touchsmart iq518a, don't know why it worked but i fixed it by going to programs and features on the control panel and uninstalling the 'bluetooth by hp' program. Everything still works perfectly and that annoying message no longer comes up.
Hope this helps
Mat
Message Edited by Knobby_103 on 04-24-2009 03:03 PM

I am using firefox on Windows 7 home premium platform today I updated my firefox to its latest version i.e. 3.6.12 I restart my system but when I click on firefox icon nothing happened in fact its exe was running in backend

Hi! I am using firefox on Windows 7 home premium platform today I updated my firefox to its latest version i.e. 3.6.12 first I uninstall the firefox but keeps my personal setting and then restart my system but when I click on firefox icon nothing happened in fact its exe was running in backend firefox version 3.5 is working fine on my system as I low grade myself to 3.5 again. Kindly help.

A possible cause is security software (firewall) that blocks or restricts Firefox without informing you about that, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox.
See [[Server not found]] and [[Firewalls]] and http://kb.mozillazine.org/Firewalls

I recently brought a mac and downloaded windows with the help of boot camp and by mistake i installed windows 7 ultimate version whereas i had the cd and serial key of windows home premium i started installing windows home premium from windows 7 cont...

I recently brought a mac and downloaded windows with the help of boot camp and by mistake i installed windows 7 ultimate version whereas i had the cd and serial key of windows home premium i started installing windows home premium from windows 7 ULTIMATE then after the exctraction of files and everything the windows setup came and my mouse and keyboard stopped working and i dont know how to open mac os x there is no option anywhere?? what shall i do pls help!!!!if there are any keyboard shortcut key to open mac os x or boot camp pls mention.

For Boot Camp issues please repost in the Boot Camp forum located by clicking Boot Camp

New Computer 64 Bit W7 Home Premium - problem with Ext HD E/: says in use

Brand new computer with Windows Home Premium 7 64 bit and then added this ext HD and downloaded clean new install of programs.[Now this Toshiba was E drive on previous computer which started life as XP Home and ended as Windows Premium 7 32 bit and brought
across the data. But Easy Transfer Wizard back up was corrupt. Luckily had cut and pasted as a precaution having always suffered bad backups.]
But problems arising with browsers not working correctly etc vendors say messages incorrect like windows saying re Pale Moon x64 clean install from web working then closing that its settings should be XP when the creator on being asked said was created for
W7 never XP and check for problems elsewhere. IE11 problematic too as well as Opera, Chrome and Firefox so tracked down to below or do complete re-install of system. OS is authenticated as genuine by M$. Scans MSE, SAS, Malawarebyes clean.
Ever since I installed the Ext HD a Toshiba 500B USB3.0 & 2.0 it has appeared and then disappeared on Devices & printers when there says 3.0 device checking properties unknown bu recognizes it as Toshiba.
I used it to bring over data from old computer which it did. Also for backup. Checking first backup - nonsense all data is different displays of IE11 start ups. Nothing else. Now deleted. Windows also said not compatible.And windows is continually
loading drivers to this device. I think that is what is the cause of its disappearance - shut down and boot sometimes back, sometimes not. Yet scanners find it when when not available.
OK so now how do I get Windows 7 to eject the drive and then try to put it on and get it recognized and working correctly. Because it could be why also backup corrupt. I have formatted it now and transferred all needed over to C Drive. I am not sure what
happens with this re drivers - it came without any software say plug and play and drag and drop ready for use with Windows.
If I can get this working correctly it will save me a complete re-install. As hate to do that and then find same problem with the External Drive. AfAIK no problems with it formatted now and ready to go and no bad areas.
Has to be this continual bringing down of a driver and fact checking Windows cant find it on list of compatibles. Vendor says it is.

Thanks I had already run Check disc and contacted Toshiba and it has correct driver. Definitely a problem with the actual system disc.
I have also completed website asking for my model to be added to compatible sites and just have to hope seeing as no direct contact available, must be only company in the world that gets away with that.
Managed to work around the E/: problem by adding it to Libraries and then cut and pasted the whole date files and photos ready for new disc.
Backup simply is corrupted so also the wizard to find new device- wont search or load and greyed out, so have arranged with manufacturer for a new disc - the one I should have bought at the time instead of using the upgrade.
With the Device & Printer device it says I have the keyboard 3000, a compliant mouse and and a HID keyboard device as well as M$ wireless transceiver and of course a 3.0 unknown device which is E Drive. So along with monitor and computer tower
7.
The keyboard is wired via a USB and only the mouse is wireless via the transceiver. So what the HID keyboard device is is a mystery too. So problem there in that wizard too. Plus had to uninstall Mouse/Keyboard ?Centre which improved the performance of the
mouse as 1 setting not 2.

Will my creative suite 3 program work on windows home premium 64 bit computer? I need to switch computers because my current pc is windows xp

will my creative suite 3 program work on windows home premium 64 bit computer? I need to switch computers because my current pc is windows xp

yes, though you may need to use compatibility mode to install.

How do I re install windows home premium OA?

I had windows home premium OA on my computer , but I believe it was accidentally uninstalled from my hard drive. I have the product key that is on my computer. I was having trouble finding the correct link to reinstall it on my lap top.
When I went to the microsoft Website all I found was support for windows 8 . Can you give help me with the proper link? thank you

Please provide the manufacturer and model of your pc.
It is possible you have a hidden recovery partition on your hard drive which may be used instead of a recovery disk to restore your system (and Windows) to factory defaults.
Recovery procedures vary from manufacturer to manufacturer.
You should also search for any recovery disk/s that were supplied with your pc. Manufacturers invariably charge a significant fee to supply replacements.
If you decide to use borrowed/downloaded media to reinstall Windows on an OEM pc, the process may not be straightforward. Without some experience and patience you may end up with no other option than to pay a professional to finish the job.
Microsoft does not publicly provide download links for Windows. While you may stumble upon an official download source, beware that many unofficial sources will come pre-loaded with viruses, trojans etc.

Had a problem after download updated itune, error 7 (window error 126) cant open itune at all

Had a problem after download updated itune, it failed as Error code MSVCR80 and then next message is error 7 (window error 126), cant open itune at all

Had a problem after download updated itune, it failed as Error code MSVCR80 and then next message is error 7 (window error 126), cant open itune at all

Multiple Samsung Stratosphere problems after FF1 update

There have been multiple posts on various issues users have found after the recent Stratopshere FF1 update. Some were replys to older posts and some only touched on a single issue. I wanted to consolodate into one thread, and hopefully get teh attention of Verizon to maybe reply here.
For reference, a lot has been discuss here --> https://community.verizonwireless.com/message/874446
Summary: Verizon and Samsung have finally updated the Stratosphere almost 1 year after release. This updated the phone from Android 2.3.5 to Android 2.3.6. Going by filename, this is known as the FF1 update. This update went live at the end of August 2012, and most users were upgraded before mid September 2012.
There were some noticable changes in this update:
-Lock screen has changed. The puzzle piece and glass lock options have been removed. New options have been added, such as facial recognition unlock.
-Call answering screen has changed, introducing the option to ignore call with a message.
-Camera now has digital zoom ability.
-Ability to uninstall the 2 games the phone comes with (Need for Speed and Lets Golf)
-Phone icon has changed ever so slightly
-Wifi icon now included up and down arrows to indicate data is being sent or recieved
-Wallpaper no longer "stretches" over multiple screens - ie, it no longer scrolls as you move from screen to screen
-The visual voicemail app has been improved (I have personally not used this feature)
-Callback number is now supported in text / picture messages
-Android core OS updated from 2.3.5 to 2.3.6 (both versions are still Gingerbread)
-Update to how the device deals with the end of scrolling. It used to rubber-band bounce back, now it will just give a green bar and expand the bar as you scroll. (I cannot fault Samsung for this change as this was at teh core of an Apple lawsuit and has been changed in newer versions of Android.)
-(I am sure there are more. please list any others you may have noticed)
I have found some problems, and others have confirmed that this is (at least) somewhat widespread:
-The biggest problem is with wifi connectivity. Upon an initial connection to wifi, everything works great. After somewhere between 15minutes and 2 hours, problems start happening. Its as if the wifi keeps hanging or reconnecting. Download speeds (tested with the SpeedTest.com app) slow to about one third of normal. Apps like Facebook that require a constant connection will just time out.
-It appears the signal strength for 3g and 4g connections is lower. There are places where I used to get a 4g connection, and now I only get 3g. Some palces I fall back to just 2g digital.
Another minor issue i found was with text messages. When you reply to a message, it no longer automatically focuses the text in the input box. You have to first click into the box to start typing. Not a huge deal, but one more step to take over and over. Minor annoyence.
At my house, I struggle to get a 3g or 4g signal. I depend on wifi for my data connection. So with the wifi connection problem introduced by teh FF1 update, my phone is somewhat useless to me now while at home. Here are teh troubleshooting steps I have been through so far to attempt to fix the wifi problem:
-Complete factory reset on my phone. (did not help)
-Pull battery and SIM card out of phone for 15 minutes. (did not help)
-Went to a Verizon store. The guy at the store was helpful, and said he also had a Stratosphere and was getting the same wifi problems after the update. He said all he could do was to send me out a replacement phone. I got the replacement phone, and it had the same problems.
-I read in multiple palces that Android 2.3.6 has a bug within wifi and DHCP. Apparently if you have a DHCP lease set to "forever", the phone will keep requesting a new address. Setting the DHCP server on the router to something like 2 weeks, or using a static IP is supposed to solve this. I have a NetGear N900 router, and I can not change teh DHCP lease time. It appears, however, that my router is not sending out "forever" leases. But just to make sure, I gave my phone a static IP. (None of these steps made any difference).
The only thing that temporarily fixes the problem is a reboot of the phone. This will again give you anywhere from 15min to 2 hours of good wifi use before problems start happening.
I have now had this update for over a week, and on 2 phones. I still can't maintain a wifi connection for much longer than 15 minutes without problems starting up.
I am asking Verizon or Samsung to at least confirm this issue if possible. Maybe there are newer revs of the Stratopshere hardware that don't have this problem. Or there is something unique about my (and apparently others) situation. But it seems like Verizon's current stance is to offer a repalcement phone (as currently all Stratospheres are within their 1 year manufacture warranty as the phone has not been ouy for quite 1 year yet).
I am asking for a workaround for this problem, or a true fix adressed by a new software update, or at least allow us to roll back to the original Andorid 2.3.5 software.
I have had my original Stratosphere for almost a year with no wifi problems - then get the FF1 update and have had nothing but problems on 2 different phones.
Thank you for your time.

Thanks for starting a comprehensive thread on problems with this update. I want to add one more.
I have Bluetooth in my car (a 2004 model), and previously the phone has connected to it practically instantly when I start the car. Since the update, I have never been able to connect the phone to the car by Bluetooth. Several times the phone has made a standard notification sound at the moment it should be connecting to Bluetooth, though no notification appears. I have no idea what that could mean.The car's Bluetooth shows up as paired in the list of devices in Settings > Wireless & networks > Bluetooth settings. I haven't seen this widely reported as an update issue, but perhaps some others have experienced it too.
UPDATE: I finally did some testing, and found that the notification was to signal the extremely brief appearance of a dialog indicating that the car's Bluetooth was requesting a connection. Accepting that request let the phone connect with the car, and calls went to the car's sound system as they should. When I turned the car off and back on (just the electrical system; not wasting any gas on this!), the connection was established immediately, so apparently the acceptance only had to be done once. Nevertheless, it did have to be done, and the dialog notification disappears within seconds. I believe it would have been possible to go into Bluetooth settings and accept the connection request there if I missed the notification; but not seeing the notification, I might not know to do this.
One further observation: When I turned the phone's Bluetooth off and back on after a connection had been established, leaving the car on the whole time, the two did not reconnect. I believe that may be different from before the update, but I'm not really sure.
Message was updated by David Rensberger

System failure after critical updates auto downloaded on HP-DV7 17.3" AMD Quad Core

After critical updates system auto reboot closed programs and went into reboot mode but system will not reboot and cannot run recovery successfully. Windows tries to load files and get to the start windows screen but will not complete. Not sure if it will bring me back to orig. format, was not able to find a restore point and do not have any reboot disks. Still under warranty but no list of available service people in area. Easy to buy hard to get service! UGH! HELP PLEASE. Thanks

Hi:
Make your own windows 7 repair/reinstallation disk and use the repair option to see if you can get it fixed.
Use the repair with command prompt method and try the fixboot command.
http://support.microsoft.com/kb/927392
Here's how to make a W7 installation/repair disk.
I just copy and paste my standard instructions for using this disk to reinstall windows.
You don't need to enter the product key to repair windows, only to use this disk as a last resort to reinstall windows.
If you can read the 25 character Microsoft windows 7 product key, you can download plain Windows 7 ISO files to burn to a DVD for the version of windows that came installed on your PC, and that is listed on the Microsoft COA sticker on your PC's case.
Burn the ISO using the Burn ISO option on your DVD burning program and burn at the slowest possible speed your program will allow. This will create a bootable DVD.
Or use the Windows 7 USB/DVD installation tool to compile the ISO file you download from Digital River. Link and instructions below. You need a 4 GB flash drive to use the USB method of compilation.
http://www.microsoftstore.com/store/msstore/html/pbPage.Help_Win7_usbdvd_dwnTool
Use the 25 character product key on the PC to activate the installation.
The key will activate either a 32 or 64 bit installation.
Then go to the PC's support and driver page to install the drivers you need.
Link to the W7 ISO file downloads is below.
http://www.mydigitallife.info/official-windows-7-sp1-iso-from-digital-river/
Paul

EFI Problems after last update anyway to downgrade ??

Hello
EFI Problems after last update anyway to downgrade ??
i have updated my MacBook 2010 EFI to MB71.0039.B0E which is 2.1 version
after updating to this version the Boot time become much slower when i want to change boot partition
and shutdown become very much slower and startup too
i tried to install Mac OS X Lion again but it doesnt help
can i downgrade to this version 2.0 ???
or when Apple will release the new version ?
or where can i send a feedback regarding this issues !!!!
Thanks

These are user to user forums. If anyone knows the answer, they will give it.
You can always call Apple support which may charge a fee or you can patiently wait for an answer here, which is free.

Share and save problem after latest update

hello,
i have share and save problem after latest update - i have installed ps touch on nexus 5 about 2 months ago and until yesterday everything was good but after latest update i can't save and share images in ps touch ( i do reinstall this app but problem is still and app doesn't work properly ) how can i downgrade to the old version ? Could you fix this problem quickly ?

i use app which called "aLogcat"
--------- beginning of /dev/log/main
I/dalvikvm(24476): Enabling JNI app bug workarounds for target SDK version 11...
D/dalvikvm(24476): GC_CONCURRENT freed 174K, 2% free 17054K/17264K, paused 2ms+2ms, total 15ms
W/InputEventReceiver(24476): Attempted to finish an input event but the input event receiver has already been disposed.
W/InputEventReceiver(24476): Attempted to finish an input event but the input event receiver has already been disposed.
W/InputEventReceiver(24476): Attempted to finish an input event but the input event receiver has already been disposed.
--------- beginning of /dev/log/system
W/ViewRootImpl(24476): Dropping event due to root view being removed: MotionEvent { action=ACTION_MOVE, id[0]=0, x[0]=38.0, y[0]=-115.0, toolType[0]=TOOL_TYPE_FINGER, buttonState=0, metaState=0, flags=0x0, edgeFlags=0x0, pointerCount=1, historySize=2, eventTime=27743080, downTime=27743066, deviceId=4, source=0x1002 }
W/ViewRootImpl(24476): Dropping event due to root view being removed: MotionEvent { action=ACTION_UP, id[0]=0, x[0]=38.0, y[0]=-115.0, toolType[0]=TOOL_TYPE_FINGER, buttonState=0, metaState=0, flags=0x0, edgeFlags=0x0, pointerCount=1, historySize=0, eventTime=27743086, downTime=27743066, deviceId=4, source=0x1002 }
D/dalvikvm(24476): GC_FOR_ALLOC freed 122K, 1% free 17271K/17428K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 10K, 1% free 17434K/17604K, paused 7ms, total 7ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 65K, 2% free 17690K/17928K, paused 8ms, total 8ms
I/dalvikvm-heap(24476): Grow heap (frag case) to 17.615MB for 328336-byte allocation
D/dalvikvm(24476): GC_FOR_ALLOC freed 0K, 2% free 18010K/18252K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 18011K/18252K, paused 9ms, total 9ms
I/dalvikvm-heap(24476): Grow heap (frag case) to 18.073MB for 479536-byte allocation
D/dalvikvm(24476): GC_FOR_ALLOC freed 0K, 2% free 18479K/18724K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 2% free 18481K/18724K, paused 2ms+1ms, total 10ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 6ms
I/dalvikvm-heap(24476): Grow heap (frag case) to 18.532MB for 479536-byte allocation
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 18949K/19196K, paused 9ms, total 9ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 2% free 19418K/19668K, paused 1ms+1ms, total 10ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 7ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 19592K/19844K, paused 8ms, total 8ms
I/dalvikvm-heap(24476): Grow heap (frag case) to 20.049MB for 933136-byte allocation
D/dalvikvm(24476): GC_FOR_ALLOC freed 0K, 2% free 20503K/20756K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 2% free 21416K/21668K, paused 1ms+1ms, total 12ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 50K, 2% free 22351K/22580K, paused 7ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 5K, 1% free 23900K/24140K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 1% free 25824K/26084K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 3411K, 14% free 24528K/28204K, paused 12ms, total 13ms
D/dalvikvm(24476): GC_CONCURRENT freed 2814K, 14% free 24256K/28204K, paused 2ms+1ms, total 11ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 4ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 9266K, 1% free 17270K/17424K, paused 10ms, total 10ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 15K, 1% free 17575K/17748K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 22K, 2% free 17875K/18072K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 1K, 2% free 18195K/18396K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 18517K/18720K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 18838K/19044K, paused 11ms, total 11ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 19159K/19368K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 19480K/19692K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 19974K/20192K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 20616K/20840K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 21431K/21664K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 2% free 22714K/22960K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 182K, 2% free 24004K/24432K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 8478K, 33% free 17593K/26228K, paused 14ms, total 14ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 18K, 32% free 17895K/26228K, paused 12ms, total 12ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 18K, 31% free 18198K/26228K, paused 11ms, total 11ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 1K, 30% free 18519K/26228K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 29% free 18840K/26228K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 26% free 19482K/26228K, paused 2ms+1ms, total 14ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 10ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 23% free 20297K/26228K, paused 2ms+1ms, total 15ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 11ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 19% free 21260K/26228K, paused 10ms, total 10ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 15% free 22543K/26228K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 182K, 9% free 23979K/26228K, paused 21ms, total 22ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 8485K, 33% free 17598K/26132K, paused 13ms, total 14ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 25K, 32% free 17894K/26132K, paused 12ms, total 12ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 12K, 31% free 18204K/26132K, paused 12ms, total 12ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 1K, 30% free 18524K/26132K, paused 12ms, total 12ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 28% free 18845K/26132K, paused 8ms, total 9ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 26% free 19487K/26132K, paused 1ms+0ms, total 9ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 7ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 23% free 20129K/26132K, paused 9ms, total 9ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 20% free 21091K/26132K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 15% free 22375K/26132K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 9K, 9% free 24011K/26132K, paused 14ms, total 14ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 2147K, 10% free 23855K/26456K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_CONCURRENT freed 8776K, 35% free 17337K/26304K, paused 3ms+2ms, total 20ms
W/InputEventReceiver(24476): Attempted to finish an input event but the input event receiver has already been disposed.
W/InputEventReceiver(24476): Attempted to finish an input event but the input event receiver has already been disposed.
W/ViewRootImpl(24476): Dropping event due to root view being removed: MotionEvent { action=ACTION_UP, id[0]=0, x[0]=564.0, y[0]=-50.0, toolType[0]=TOOL_TYPE_FINGER, buttonState=0, metaState=0, flags=0x0, edgeFlags=0x0, pointerCount=1, historySize=0, eventTime=28190972, downTime=28190972, deviceId=4, source=0x1002 }
D/dalvikvm(24476): GC_CONCURRENT freed 186K, 31% free 17626K/25476K, paused 2ms+1ms, total 12ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 4ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 63K, 30% free 17884K/25476K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 3K, 29% free 18201K/25476K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 27% free 18696K/25476K, paused 2ms+1ms, total 12ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 9ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 25% free 19190K/25476K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 23% free 19831K/25476K, paused 9ms, total 9ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 19% free 20794K/25476K, paused 2ms+0ms, total 12ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 8ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 14% free 22078K/25476K, paused 1ms+2ms, total 14ms
D/dalvikvm(24476): WAIT_FOR_CONCURRENT_GC blocked 12ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 7% free 23855K/25476K, paused 10ms, total 10ms
D/dalvikvm(24476): GC_CONCURRENT freed <1K, 6% free 24176K/25476K, paused 2ms+1ms, total 14ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 6440K, 26% free 19562K/26216K, paused 9ms, total 10ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 93K, 23% free 20207K/26216K, paused 10ms, total 10ms
D/dalvikvm(24476): GC_FOR_ALLOC freed 11K, 21% free 20935K/26216K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 18% free 21673K/26216K, paused 9ms, total 9ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 15% free 22499K/26216K, paused 8ms, total 8ms
D/dalvikvm(24476): GC_FOR_ALLOC freed <1K, 10% free 23695K/26216K, paused 9ms, total 9ms

IPhone 4s got problem after I update to 7.1.1. Battery drain so fast

iPhone 4s got problem after I update to 7.1.1. Battery drain so fast

The Ultimate Guide to Solving iOS Battery Drain
<http://www.overthought.org/blog/2014/the-ultimate-guide-to-solving-ios-battery-d rain>

Please Read This To Reduce or Eliminate Problems after Software Update

Hi all, I have been reading quite a handful of Mac users here reporting problems ranging from minor ones like slow downs to major ones like application crashes, and many of them blame the new OS and/or Security Updates.
Without learning more from the details of how did they perform their Software Updates and Install, I am making a huge assumption that it maybe something they did or didn't do, one of the key things they did not do is Repair Disk Permission
Below is what I called, the "ritual procedure" needed to perform before and after a Software Update, and also any other major software installation - to help reduce or eliminate "hiccups" afterwards, I cannot gaurantee that all macs all over the world will not suffer any problems after an update, but by doing so, you may help reduce it; I have 4 macs all together and so far I have not encounter any major problems after many versions updates.
Anyway, I didn't come out with this series of procedures, I read it off somewhere in this Discussion quite a while ago, and thought I share it again with all of you:
1.Before starting Software Update, unplug all external devices, FireWire, USB, hubs etc etc, not just turning them off but unplug the cables off your Mac, leave only your keyboard, mouse and internet connection on (unless you are using a wireless keyboard and/or mouse or on wireless internet)
2.Repair Disk Permission
3.Restart the Mac, then start your SU, do not run any other apps.
4.After finishing SU, restart your mac; If you are updating OS or Security Updates, Restart is required.
5.Repair Disk Permission again
6.Shutdown and re-plug in everything and start up your mac as normal.
I know the procedure is pretty long and "troublesome", especially the unplugging and restarting part, but so far it really has done my macs good, so I am going to "swear" by it... my FireWire, USB devices etc still work as normal.
This is really contrary to that "Macs are easy to use", yes, no doubt about it, but the software updates etc is just well, put it this way: The Mac OS when it comes to updates, is very very delicate... so handle with it great care, it will just turn out okay.
Cheers

Thank you for posting that. I posted a similar set of suggestions here:
http://www.macmaps.com/backup.html
Disclaimer: Reference to links I make to my Macmaps.com website are a for your information only type reference. I do not get any profit from this page, and it is open to the public.

TouchSmart 520 Windows 7 Home premium Problems after critical updates

Similar Messages

Maybe you are looking for