Touchsmart IQ770 - IR stopped working after Windows 7 Install

Have had the satellite hookup working under Vista. Loaded up Windows 7 and now when I try to setup the tuner the IR is not found.
During Tuner setup I see the signal and hear the audio, it is just the IR part that stops the setup configuration from working.
Could the Bluetooth be interference?

Try to install the HP Remote Solution software when it becomes available to see if that works.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01778879&lc=en&dlc=en&cc=us&product=3781376&lan...
Certain buttons on the Remote Control for Media Center might stop working.
Update to the latest HP Remote solution download from www.hp.com/support .

Similar Messages

Usb ports stopped working after windows 7 install - pavilion g6-1001sa

After reinstalling windows - My usb ports have completely stopped working - not recognised at all - These happened previously and I was able to download and install a driver which worked - I have been unable to find it this time
thanks
JO
Please help

teethinnit wrote:
I had tried here - the correct driver was not here - it is the USB controller that I am looking for
Ok go to your search bar and type "Change Device installation settings"
and look at my screen shot and this change should make it look for the latest driver.
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

FIngerprint reader stopped working after windows automatic updates

Hi,
I recently purchased an Envy j109tx laptop.
From day one the finger print scanner was not working.
After updating hp simplepass it started to work.
Again today I installed some windows update. After that it stopped working.
The light in the fingerprint reader is not turning on.
Is there a fix for this?
Someone please help me.
Thanks in advance.

@naga5speed ,
Hello and thank you for posting on the HP support forums. First thing did you do the windows update due to your system having some issue?
If not then do a system restore back before the update.
It is probably some microsoft update that is conflicting with the driver.
It is good to keep your system up to date. But it is better to make sure before you run an update that you take a look as to why you are updating.
Do I need to fix an issue?
If i do not do the update will something stop working?
Using Microsoft System Restore (Windows 8)
If this fails to work then you may have to back up your data and run a system recovery. The reason for this is what ever update you ran has made changes to system files or the registry that a restore will not fix.
Performing an HP system recovery (Windows 8)
Here is another link you may find useful.
Fix Microsoft Windows Update Issues
Please let me know how things go.
Thank you again for posting and have a great day.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

Boot keys stopped working after Leopard install

I have seen others having this problem in another thread but no answers, so thought I'd give it a go.
After reading these threads finally got Leopard to install and run okay. Many thanks all. But, along the way, my boot keys stopped working. It doesn't matter what I hold down, whether 'c' or 'cmd-opt-p-r' or 'shift' or any other key combination the machine just boots straight into Leopard.
I have tried resetting the PMU (or whatever it is these days) via the internal button in desperation but still no luck.
Anyone with any ideas?

Same problem here, so I'll pull this post up. No key works.
I always have to go to the Start Drive (or whatever it's called in english) in Preferences Panes and choose the partition I wish to start directly in OSX or Windows for booting back to OSX. This is very annoying. Alt key won't show up any possible boot disk although their both internal drives.
If someone would kindly post any ideas how to change that, would be great. I've done a fresh install, with a Time Machine recovery, but this didn't seem to help.
EDIT:
I found another subjet here from november '07:
http://discussions.apple.com/thread.jspa?threadID=1224639
it seems the new Apple Keyboard is the origin of the Problem on iMac Core Duo. Apple techs said that a new firmeware should be coming before the end of 2007 (but it's february 2008 now ?!?). Any other ideas how to get this work ? I'll write on Aplpe feedback page for sure. Maybe the other boot keys aren't working because of this keyboard too.
Message was edited by: Nordlaser

ITunes has stopped working after fresh install

Hey there,
Hoping someone can help me out. I've had iTunes for a while but just had to get my computer repaired and after a fresh windows install I am not able to get iTunes to work. I've searched the help forums and tried many things already but had no success.
Some computer info:
Windows 7
Processor: AMD A10-7700K Radeon R7, 10 Compute Cores 4C+6G 3.40 GHz
Installed memory: 4.00 GB
System Type: 64-bit Operating System
The error report I get:
Problem signature:
Problem Event Name: APPCRASH
Application Name: iTunes.exe
Application Version: 12.1.1.4
Application Timestamp: 54de1991
Fault Module Name: CoreAudioToolbox.dll
Fault Module Version: 7.9.9.6
Fault Module Timestamp: 54ddd41b
Exception Code: c000001d
Exception Offset: 00000000001fa332
OS Version: 6.1.7600.2.0.0.256.1
Locale ID: 1033
Additional Information 1: 4f7c
Additional Information 2: 4f7c296d7de48197416f5a96255d8b8d
Additional Information 3: 9f55
Additional Information 4: 9f55f98d4376c33fdaaf6d0e91a7f07b
Please help me figure this out.
I have already tried the following:
- Uninstalling iTunes and all the components and reinstalling iTunes
- Uninstalling iTunes and reinstalling in Safe Mode (wouldn't work)
- Downloading iTunes for slower video cards and installing that (didn't work)
- Downloading an older version of iTunes (would just rollback during install and not let it complete)
- Tried a different user on my system and also didn't work
Any help is appreciated. I love using this product and would like to continue using it.

also when I open itunes in safemode (using shift+ctrl), it works normally...

DVD drive stopped working after Mavericks install

I have a Macbook Pro (late 08 model) that was running Snow Leopard. I recently did a clean install of Mavericks and since then the DVD drive just spins and ejects discs without being able to read them (doesn't seem to matter what I use. Software, games, audio cds, etc..). It was working fine before installing Mavericks and I can still boot from the DVD drive (old snow leopard boot disc) but it won't read any discs once booted into the OS even though the OS is detecting the drive just not the disc when inserted.
I've tried resetting the NVRAM/PRAM and resetting the SMC as suggested on other forums but like many others with the same issue it didn't help. I also cycled through several drutil commands as suggested to "wake up" the drive but that didn't help any either.
I'm kind of stumped here guys. I could roll back to Snow Leopard but I've got some software thats dropping support so I'd rather be running Mavericks if I can sort out this DVD drive issue. Clearly its not the drive itself since it worked fine before and I can boot from it. Any ideas?

Hrm looks like I might of fixed it. I went back after seeing another post about spamming drutil commands to "wake up" the drive and just spammed them about 20 or so times and the drive started working again.
I'm still very confused as to why it just stopped working within the OS after installing Mavericks (yet I was still able to boot from the DVD just fine). Clearly something is bugged in mavericks. I even came across a post on the apple forums from someone with this issue and it was effecting both his late 08 and early 2013 Macbook Pros.
I'll keep an eye on my own machine to see if it stops working again but for now it seems my drive is "fixed" go figure.

Itunes stops working after update install

Anyone have the issue where itunes stops working post the latest update install? Ive even uninstalled itunes and attempted to reinstall and it doesnt work

Hey Rockettman23,
Thanks for the question. I understand that you are experiencing issues with iTunes for Windows. I also understand that you have already attempted to reinstall iTunes. You can use the steps in this resource to further isolate the issue to user-specific or system-wide:
iTunes for Windows Vista, Windows 7, or Windows 8: Fix unexpected quits or launch issues
http://support.apple.com/kb/TS1717
Thanks,
Matt M.

Yahoo messenger voice chat stopped working (after archive & install)

I have an iMac5 Intel Core 2 Duo 2.16 GHz. I (actually my wife) was using Yahoo Messenger v3.0 beta 4 (built 156957) for all chat and voice chat. About 2 months ago voice chat stopped working. when i send invite, it keeps ringing (but the receiver never sees any invite). When the other person sends me an invite, I don't get anything.
I have downloaded Gizmo, but it also keeps "connecting...".
About 2 months ago, I had to archive and install to solve a Java update issue which was causing wierd problems. Thanks to BDAqua's advice I managed to resolve that. I have J2SE 1.4.2 and 5.0; everything else is working fine.
What can cause voice chat to stop working? Is there some vc plugin in library that needs to be there, which has disappearted after my "archive and install'? Please advise. thanks Fahd

Hi again Fahdali,
Have you tried reinstalling it since then?
http://www.apple.com/downloads/macosx/email_chat/yahoomessengerformac.html
Or...
http://wiki.answers.com/Q/CaniChat_be_used_with_yahoomessenger

8i on NT Listener stops working after Designer install

We installed Oracle 8i Enterprise Edition 8.1.5.0.0 on NT. Database worked fine. After installing Designer 6.0, the Listener will not start.
FYI, for the Designer installation, we used the same ORACLE_HOME name as the database, but a different directory location. Any suggestions?
Please redirect us to another forum if appropriate.
Thanks,
-Don & Van
null

Ravi,
Thank you for your prompt reply.
1. Your answer would suggest that we have not installed the products in the proper order. Would you suggest that we de-install and re-install in the order you listed?
2. Could the installation order have caused the Listener to stop working?
3. Can you suggest another approach to resolving the Listener issue other than re-installing Designer and Oracle 8i in the order you suggested?
Thanks again,
-Don & Van

9i Report Builder stops working after 10g install

I have the 9i Developer Suit installed and recently I installed the 10g Developer Suit. After installing the 10g Developer Suit the 9i Report Builder stopped working. When I try to start it, it hangs at the launch screen. All the other apps in the 9i and 10g Developer Suits seem to work except for the 9i Report Builder. Please Help.

Nope. The 10g report builder works fine. The issue is only with the 9i report builder.

Toupad Tapping and Scrolling stopped working after Windows 10 Upgrade

Hi, I upgraded my OC to Windows 10 today, after the upgrade tapping and scrolling stopped working on the synaptics touchpad. the toucpad only finctions as a pointer now. for taps/Clicks i always have to use the buttons below the touchpad. It was working fine before the upgrade, the earlier OS was Windows 7 I have checked for driver updates but i get a message that the drvier is up to date.I have check the device setting and confirmed that tapping and scrolling is enabled.I have also done a device reset. Nothing solved the problem, i also did not find a relevant answer on the forums.Also, the same problem did not happen with my other HP laptop (Notebook PC) which was also upgraded to windows 10 recently. Does anyone have a solution? Regards,Siddharth.

, Hello and thanks for posting on the HP support forums. What you will need to do is the run the Windows Update Fixer tool. Here is a link to help you with that. Make sure you run all updates including optional. Fix Microsoft Windows Update Issues If that fails to work the only other option is to roll your system back to the original supported operating system that came with your notebook. Thanks again for the post and have a great day.

Satellite P200 - Microphone has stopped working after Windows 7 install

My Satellite P200 came with Vista Ultimate, the mic worked for a few months suddenly it stopped. I decided to install Windows 7, but mic still does not work.
Any ideas anyone?
I use this laptop to skpe my folks a lot. I can use an external mic fine, but really want my inbuilt one working again.

Hi buddy,
Sounds like its something wrong with your Windows 7 installation if the microphone doesnt work anymore...
I would recommend updating the webcam driver because the microphone is a part of it. You can find driver updates here:
http://eu.computers.toshiba-europe.com
I dont know what Satellite P200 you have exactly but if you cant find a Windows 7 driver for webcam, choose another model that is fully Windows 7 supported, e. g. Satellite P300.

10g stopped working after 11g installed. Getting ORA-12514: error

I had Oracle 10g installed in win2000 sp2. with port 1521.
I have installed Oracle 11g on the same system. with port 1522.
I am able to start both the instances and tnslistener but I am not able to connect to Oracle10g database. Getting following error.
ORA-12514: TNS:listener does not currently know of service requested in connect
descriptor
I have done the following check.
c:\> tnsping tek10g
TNS Ping Utility for 32-bit Windows: Version 11.1.0.6.0 - Production on 14-MAR-2
008 13:04:26
Copyright (c) 1997, 2007, Oracle. All rights reserved.
Used parameter files:
C:\app\mmurugai\product\11.1.0\db_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS_LIST = (ADDRESS = (PROTOCOL = TCP)
(HOST = PC456)(PORT = 1521))) (CONNECT_DATA = (SERVICE_NAME = tek10g) (SRVR = DE
DICATED)))
OK (50 msec)
2) Checked lsnrctl services
LSNRCTL> services
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=PC456.SYNTELORG.COM)(PO
T=1522)))
Services Summary...
Service "orcl11g" has 1 instance(s).
Instance "orcl11g", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:3 refused:0 state:ready
LOCAL SERVER
Service "orcl11gXDB" has 1 instance(s).
Instance "orcl11g", status READY, has 1 handler(s) for this service...
Handler(s):
"D000" established:0 refused:0 current:0 max:1022 state:ready
DISPATCHER <machine: PC456, pid: 284>
(ADDRESS=(PROTOCOL=tcp)(HOST=PC456.SYNTELORG.COM)(PORT=2963))
Service "orcl11g_XPT" has 1 instance(s).
Instance "orcl11g", status READY, has 1 handler(s) for this service...
Handler(s):
"DEDICATED" established:3 refused:0 state:ready
LOCAL SERVER
The command completed successfully
LSNRCTL>
I am not able to see my tek10g 10g database details.
I also checked my tnsnames.ora file which has the entries properly.
Sqlnet.ora file has
SQLNET.AUTHENTICATION_SERVICES= (NTS)
NAMES.DIRECTORY_PATH= (TNSNAMES, EZCONNECT)
How to solve this issue? Is that possible to run oracle 10g and oracle 11g in same host?
Thanks in Advance...
regards,
Manikandan

The approach I would take, in general is:
1) pick a listener, and only one. Get that working.
2) Make sure all the databases register to that listener
3) Fix the TNSNAMES.ORA files appropriately.
To fix the listener
1) Verify the listener address matches the current environment
SID_LIST_LISTENER =
(SID_LIST =
    (SID_DESC =
      (SID_NAME = PLSExtProc)
      (ORACLE_HOME = C:\oracle\app\oracle\product\10.2.0\server)
      (PROGRAM = extproc)
    (SID_DESC =
      (SID_NAME = CLRExtProc)
      (ORACLE_HOME = C:\oracle\app\oracle\product\10.2.0\server)     << - MUST point to correct HOME
      (PROGRAM = extproc)
LISTENER =
(DESCRIPTION_LIST =
    (DESCRIPTION =
      (ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC_FOR_XE))
      (ADDRESS = (PROTOCOL = TCP)(HOST = myHOST)(PORT = myPORT))
)where
myHOST is this host's resolvable name or IP address
myPORT is the port (default 1521) that the listener should monitor
The HOST is often a problem if the machine uses DHCP.
2) Register the databases
On startup, database will auto-register to the listener defined in the init parameter 'LOCAL_LISTENER', which defaults to 'HOST={current_host}, PORT=1521'
After startup, if the listener is taken down, you can register each database manually using the DBA command
ALTER SYSTEM REGISTER;
Either way, it should show up in the output of 'lsnrctl status'
While you are accessing the database, you might want to find out which services the database supports. That can be done in SQLPlus using the command
SHOW PARAMETER SERVICE_NAMES
Note that the database name is the default service name.
3) Fix [all] the TNSNAMES.ORA file[s].
Each SERVICE_NAME from the previous list that you want to access from this client, yu should find an entry that looks like
myTEST =
(DESCRIPTION =
    (ADDRESS = (PROTOCOL = TCP)(HOST = myHOST)(PORT = myPORT))
    (CONNECT_DATA =
      (SERVER = DEDICATED)
      (SERVICE_NAME = mySERVICE)
myTEST is the alias I want to look up by using it as the connect target string.
myHOST should match the HOST= entry in the LISTENER.ORA
myPORT MUST match the PORT= entry in the LISTENER.ORA
mySERVICE is the Service to which I am asking the listener to connect me, as found in the lsnrctl status output

Personas has stopped working after Windows updates. Halp! How do I get personas to start working again?

Personas was working just fine. A few days ago there was a Windows update (somewhere along the lines of 20 updates). Both our Vista laptop AND our 7 Desktop were updated and now personas doesn't work on either computer . . . with the exception of one user account on the desktop. <--- which is weird, huh?
We are perplexed. When we mouse over a persona, the font color changes but the picture doesn't. When we wear a new persona again, ''only'' the font color changes but the picture doesn't. It seems to be 'stuck' on whatever our current persona is on the computer. I also tried uninstalling personas and rebooting and . . . the persona picture was still on the computer. More weirdness. I re-downloaded personas after this but the problem persists.
I've searched and searched and can't find anything on this. My best guess is that it has something to do with one of the Windows updates as several of them were security updates ... but this is only a guess on my part.
Any help would be greatly appreciated. Let me know what other information I can provide to try and resolve this problem.
Oh, both machines are running the current versions of Java and Adobe flash. We are running on Firefox 3.6.17 on both laptop and desktop.

Anyone else experiencing this problem? Anyone have any ideas/suggestions on what to look for to try and resolve this? Thx.

After Effects CS6 stopped working after Mavericks install

I started getting a - You cant use this version of the application "Adobe After Effects CS6 with this version of OS X 10.9.1 - You have Adobe After Effects CS6" 11.0 - all my other Adobe CS6 programs are working - photoshop, premiere, bridge ect. Is this a delete and re install or is there a way around this problem?

You have to run the update for AE. You may have to use the uninstaller and then re-install. I'm guessing that this started after you ran an update for your OS.
When you ask a question assume that we know nothing about your system or your history with that system. We can provide better help if we know if your system worked before, what changed, and anything else that pertains to your problem. Something as simple as an automatic update to your virus protection can kill another app.

Touchsmart IQ770 - IR stopped working after Windows 7 Install

Similar Messages

Maybe you are looking for