Touchsmart tx2 1160ea only showing single touch in windows 7

as stated above i have just updated to windows 7 32bit ultimate, and i can use multi touch to zoom and things like before but non of the windows 7 things work, like the multi touch in paint and windows explorer.
The notebook is a touchsmart tx2 1160ea
In system it's saying, pen and touch: pen and single touch input available
Thanks for any help,
Luke

In case you have not found the answer yet, try n-trig website as well as hp.
Found by downloading and installing:
DuoSense_MTM_RTM_Win7_32bit_TouchSmartTX2_2.239.zip
Rollback_x32.zip ( and using the driver folder within)
WinTab_Setup_x32.zip
The single point was replacd by 4 points !
of course for a 64 bit OS, a 64 bit version of that software would be needed.
Hope that works for you

Similar Messages

Hold Option key at start up only show Mac OS but Windows

Hi all,
i have installed windows xp on my macbook(the new one with leopard).
and windows work well.
but when i hold option key at start up, it only show me mac os.
i don't know why.how can i make it show me 2 systems(mac and windows) after i hold option key at start up?

If I remember correctly, Bootcamp needs an NTFS partition for Windows in order to work correctly. This is the default file system for WindowsXP. The Bootcamp assistant tells you during installation that a FAT32 partition already exists and, curiously, gives you the default selection of leaving this intact. You need to ignore that and format using NTFS. If you don't, then Windows wont boot. To convert to NTFS, you will need to run the assistant again and reinstall Windows.
To overcome the problem of data portability between WinXP and OSX, I use a small 30 gig USB external drive formatted using FAT32 as a bridge between the two. Hope all this is useful?

Visual Composer 7.0.1 (EHP1) - Value Help only shows "Single Selection"

I tried to add a value help to a field that allows multiple selections. However, when I used the wizard through "Add Value Help" drop-down menu, I can only see one proposed selection - "Single selection". However this SAP help document (http://help.sap.com/saphelp_nw70/helpdata/en/b5/036d391f074f769e00602634ee9960/content.htm) mentioned about the "Multiple selection" option. What I can do to make this selection available?
I am using VC 7.0.1 (EHP1). Thanks for any helps in advance.
Kelly

Hi
Are you using 'BI Query' as 'data Service'? & are you creating value help for variable? If Yes -
Create necessary variable as 'Multiple Single Options' in your BEx query & then create value help in VC. Then it will allow multiple options or interval values.
Regards
Sandeep

Contact sheet only shows single image; need multiple duplicates

I'm trying to print an image using the "Contact Sheet" setting. I need to output a page containing multiple instances of one single image. When I select the image and select "Contact Sheet," it shrinks the single image down and sticks it in the top-left box of what should be a page full of that single image ... but it's only creating a single instance of the image, and the rest of the blocks on the contact sheet are blank.
I'm ready to put my fist through the monitor. Please help before it's too late. Thanks.

{quote:title=LarryHN wrote:}
In the customize window when you click the settings icon ther is a pull down menu in teh resulting screen that lets you select multiple photos pre page and multiples of a photo{quote}
Oh, how I do so wish that were the case, but when I click "Customize" and then get to the subsequent screen containing the "Settings" button, and then click said "Settings" button, I get, as previously stated, nothing but a dropdown that allows me to changes settings only for the text that one can select to accompany one's image, as shown in the screen capture found here:
http://dl.getdropbox.com/u/1009048/iphoto-customize-settings.jpg

External Video - No longer plays video...? Only shows single frames

Hey all - thanks for stopping by! I am hoping for help as soon as possible!
So I've been doing fine on my project up until I did the FCS 2008-03 update today... ugh (I know I shouldn't have).
I use 2 monitors; one for my timeline, etc. the other for full screen playback. It's worked swimmingly for the past month. Now, it will only play a single frame back - wherever my playhead is, generally. But takes a second to refresh.
I have external video set to "all frames" and have refreshed the external devices, restarted, reverted to QT 7.5, etc.
What can I do to get back to where it was working?
A black magic card is installed but I'm not capturing anything right now. Will that still affect it?
Thanks to all who stop by
Specs:
FCP 6.0.4
QT 7.5
10.4.11
G5 2GHz
2.5 GB DDR SDRAM

Try all these?
Shane's Stock Answer #8: External Monitor Viewing
CUTTING SO YOU ONLY SEE THE TROUBLESHOOTING THINGS
If for some reason you can't view your timeline on your external monitor, there are a few things to try:
1) Make sure that the camera/deck is connected and powered on BEFORE you open FCP.
2) In the Final Cut Pro menu select AUDIO/VIDEO Preferences and make sure your signal is being sent out thru Firewire DV.
3) Go to the menu and select VIEW>EXTERNAL>ALL FRAMES.
4) Click in the % box above the image and select FIT TO WINDOW.
5) Go to VIEW->refresh A/V devices
6) Make sure the Log & Capture window is closed
If you want it to play in both the canvas and the external monitor you need to go to the FINAL CUT PRO menu and select AUDIO/VIDIO settings and make sure MIRROR ON DESKTOP is selected under the PLAYBACK OUTPUT section.
Shane

Touchsmart IQ700 screen only shows diagional lines on start up can anyone help

Can anyone please help me as when i start up my IQ 700 all i get is coloured diagional lines on the screen and can not use the pc.

If you have been inside the machine, verify your RAM sticks are fully seated.
If you have added non-OEM ram, remove it and try to boot.
Run the Apple HW CD and perform a ram test. What are the results?

Mission Control Only Showing App Icons, NOT Windows

I just purchased a new MacBook Pro Retina and am noticing a bug with Mission Control. When I go to Mission Control to see all of the different windows I have open, it's showing just the app icons, NOT the actual app windows. This occurs sporadically; sometimes it works properly, and sometimes it doesn't. I actually realzied the same issue on my MacBook Pro (2009) after upgrading to Mountain Lion a few weeks ago, therefore it seems to be an OS issue and not a HW issue.
Here is a screen shot of what I see when Mission Control is not working properly:
Instead of those icons, it should be showing the actually windows within those apps that I have open.
Any ideas?

I have this problem too and would love a solution...when it happens to me it only seems to be on one of my spaces, if I use gestures to get to another space Mission Control" works fine on a different space, but if I go back to the original space it stops working..I have found a fix, which is just move the active window slightly, yep, that actually works, and then Mission Control starts working again...it's weird...would still love to know what causes it, even though the fix is an easy one...
Just on the safari comments above, I have noticed this happens when one of the tab has "reader" activated...turning of 'reader' seems to fix the issue with safari...

What can i do if my new iphone 5 dropped dead after the last update and it only shows itunes on its window?

i connected my phone to the copmuter to chargethen i tunes asks for an update i strted installing and left it to finish when i came back it said that the update couldnt be finished and that i should try again later but my device is not working at all it just shows yhe i tunes logo on the cover and the usb picture below it. i gess its asking for me to conect it so i did but its just charging with out doing anithyng else and i can't access my device from the computer to search the problem either.HELP PLEASE im desperate!!!

Hi jandroantonio,
Welcome to Apple Support Communities.
It sounds like your iPhone update may not have completed succesfully. Not to worry, we have an article with information on how to treat this symptom:
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808
Best,
Jeremy

Tx2 1160ea will not boot

When I power up my notebook, Touchsmart TX2-1160ea, The fan starts, and the boot sequence does not start, with num lock light slow flashing. original vista Home was upgraded about 9months ago to Win7, and worked fine up to a week ago, when the above error started to happen. Any advice / help gratefully received. Thanks Jim McDonald

Can you id the flash sequence?
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&destPage=document&docname=c01443366&jumpid=reg_r10...
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**

I have several albums by and an artist as is expected for a number of artists. But after the new iOs5 update my ipod touch now only showing one on my ipod.

I have several albums by and an artist as is expected for a number of artists. But after the new iOs5 update my ipod touch now only showing one on my ipod. I have already resynced it, any suggestions on how to fix the problem without having to restore my iPod to factory settings.

Becaise the digitizer is broken in that area
Apple will exchange your iPod for a refurbished one for $199 for 64 GB 4G and $99 for the other 4Gs. They do not fix yours.
Apple - iPod Repair price
A third-party place like the following maybe less. Google for more.
iPhone Repair, Service & Parts: iPod Touch, iPad, MacBook Pro Screens
Replace the screen yourself if you are up to it
iPod Touch Repair – iFixit

My iPod touch is not recognized on my computer and is only showing the connect to itunes screen.

I don't know what to do. It was working fine yesterday but now it won't recognize it anywhere and only shows the screen "connect to itunes" which it won't let me do.

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar
Then as necessary
iOS: Device not recognized in iTunes for Mac OS X
Or
See
iOS: Device not recognized in iTunes for Windows
- I would start with
Removing and Reinstalling iTunes, QuickTime, and other software components for Windows XP
or
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
However, after your remove the Apple software components also remove the iCloud Control Panel via Windows Programs and Features app in the Window Control Panel. Then reinstall all the Apple software components
- Then do the other actions of:
iOS: Device not recognized in iTunes for Windows
paying special attention to item #5
- New cable and different USB port
- Run this and see if the results help with determine the cause
iTunes for Windows: Device Sync Tests
Also see:
iPod not recognised by windows iTunes
Troubleshooting issues with iTunes for Windows updates
- Try on another computer to help determine if computer or iPod problem

Sync session failed to start on my ipod touch. tried to delete back up history but it only shows my daughters ipod touch and not mine! Im unable to update or purchase new aps, not sure how to fix this problem?

sync session has failed to start on my ipod touch. Tried to delete the back up but it only shows my daughters ipod touch. Iam unable to update or purchase new aps, not sure how to fix this problem?

Try:
https://discussions.apple.com/thread/3415227?start=0&tstart=0
https://discussions.apple.com/message/16400530#16400530

HT201302 When i open up itunes on my computer, it says that i have 2 videos but when i sync it and check my ipod touch, it says i have no videos so it only shows up on my computer but not on my iPod touch and its a 4th Generation.

When i open up itunes on my computer, it says that i have 2 videos but when i sync it and check my ipod touch, it says i have no videos so it only shows up on my computer but not on my iPod touch and its a 4th Generation.

Update Server
Try:
- Powering off and then back on your router.
- iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
- Change the DNS to either Google's or Open DNS servers
Public DNS — Google Developers
OpenDNS IP Addresses
- Try on another computer/network
- Wait if it is an Apple problem

HELP!!! The iTunes in my iPod touch 4g doesn't show the music . Only show the podcast.

My ITunes store in my iPod touch 4g doesn't show music,only show podcast and iTunes U.

Z i n C wrote:
Yep it doesn't show the music section,so how I want to download a song ?
You cannot buy music from itunes, as they do not sell it in your coutnry. You would have to buy elsewhere.

I have 100 songs on i pod touch. But when i connect it to itunes it only showed 44 songs. What is actually happening and how to fix the problem so that all music in my iphone can be seen in my itunes

I have 100 songs on i pod touch. But when i connect it to itunes it only showed 44 songs. What is actually happening and how to fix the problem so that all music in my iphone can be seen in my itune

If they are iTunes purchased music then go to Settings>iTunes and App Store and turn off Show All.
Next
Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Unsync/delete all music and resync
To delete all music go to Settings>General>Usage>Storage>Music>Tap edit in upper right and then tap the minus sign by All Music
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.

Touchsmart tx2 1160ea only showing single touch in windows 7

Similar Messages

Maybe you are looking for