Trace Fiber Optic Cables

Hi Folks
How to trace Fiber Optic Cables,I m Working in environment where no Fiber Optic Documentation and I Don't know how cables are running between fiber patch pannel on the rack on access switch and the fiber backbone .no label to start working and prepare documentation

Are the fibres carrying live traffic? If they are not live you can trace them with a red light source, its like a pen that has a laser that operates in a visible wavelength, heres one I found which seems to use very bright LEDs:
http://feedthenetwork.com/cable-and-satellite-tv/visible-light-use-for-fiber-continuity-testing
And this one goes 10km with a laser:
http://www.dhgate.com/10km-red-light-pen-fiber-optic-test-fault/p-ff8080812b2e44e5012b48263732532d.html
With everything you get what you pay for and cheaper ones will not go as far as the more expensive ones.
With my laser based red light source I see a break in a fibre patch cord and I can also put a gentle bend in the fibre and it will leak out the side of the sheath.
I hope this is obvious but DO NOT look into the end of a connector EVER, you can't see 1310nm or 1550nm but it will give you a very cheap laser eye surgery job and will almost certainly damage them beyond repair.
If the fibres are live you may have to disconnect them to see which port goes down, thats the safest way to do it anyway.

Similar Messages

Can I Replace or Extend the Fiber Optic Cable?

There is a cable that runs from the Verizon box outside of my house, comes into the basement corner of the house, and plugs into the router. Do I assume this is fiber optic cable? This cable is about 3 ft long which is problematic in getting a good signal throughout my house. I would like to move the router up one floor. All the other cords and cables are long enough to do so.
My question is what is this cable called and can I replace it or extend it myself? If so, is there any pertinent information I would need to know to do so such as part names and where to get them. If not, how do I get a longer cable installed.
I am not tech savvy and grateful for any help.
Solved!
Go to Solution.

rebeccajeanne wrote:
Do I assume this is fiber optic cable?
No. The fiber optic cable attaches to the Optical Network Terminal (ONT), which is usually outside.
For speed tiers < 100Mbps, the installation is usually coax from the ONT to your router.
For speed tiers > 100Mbps, the installation is always ethernet from the ONT to your router.
If the cable from the ONT is indeed an ethernet cable, you can certainly replace it.
The ONT has a standard RJ45 jack which the other end of the cable is connected to.
You can confirm if you're connected via ethernet in two ways.
1) The WAN ETHERNET light on your router should be lit and the WAN coax light should be off.
2) The ethernet cable should be connected to the white WAN port on the back of your router.
Since your ONT is outside, replacing the ethernet cable presents a couple of problems..
1) When VZ installed the cable, they passed it through the wall, then sealed the opening with silicone.
You need to make sure you can fit a preterminated cable through that opening unless you're capable of terminating a cat5 cable yourself.
2) You need to reseal the opening with silicone.
An easier option is an RJ45 coupler.
http://www.amazon.com/Britta-Products-RJ45-Coupler-F-F/dp/B000BSLW8U
rebeccajeanne wrote:
Can Verizon replace it for a longer cable?
Yes, but they will charge you a truck roll to do so. $88 or so.

How difficult/costly is it to install fiber optic cables?

I live in an area that has no underground cables, or fiber optic cables and I've lived with this 1.5 MB DSL connection for about 4 years now. Yeah, it sucks. I was curious as to what is the biggest factor when it comes to installing fiber optic cables in an area and how a company determines as to where they are going to be located. Thanks in advance.

Installing fiber optic cables is not just a "how hard is it?" question.    yes, the business considerations do take into consideration the physical issues (how hard it may be [above ground and below ground]), but there is more:   Can the company get City\county\state PERMITS to do so? What engineering problems are there? (mountains, existing drainage or other water culverts, etc.?) and then there is also the business consideration of 'how much uptake will be realized if we install the fiber cable?' (how many users in the neighborhood?)
fiber optic technology (to the premises) is here and will not go away (more like CAN NOT go away), however, until the economy picks back up, it may be cheaper for more people to see how much more can be squeezed out of the existing technologies (DSL & cable) before they want to switch to what may cost more for them. SO, in your area, the company may not be able to get the permits, maybe just not yet, who knows?   They may also not see customer uptake in your area, yet.
You may not be aware, but Verizon has recently sold-off whole states and partial states-worth of fiber-to-the-premises accounts, in what could have been Business decisions based on profit for stock holders.   -If their investments to install it will not be recouperated within the time limit required by their stock holders, it may not be installed for a while.
.02
cjacobs001

Sfp and fiber optic cabling

Hi,
I would like to ask if i can use our existing fiber optic cabling after i purchased a cisco 2960 with 4 sfp uplinks also, i purchased sfp modules for each switch. Does it mean that i only need to purhcase a converter from ST for SFP?
thanks

If the fiber type is compatible with your transmission type (single mode versus multi-mode) then all you need is to correct the physical connection.
You can change the connectors (or, more likely have them re-terminated by a pro ... it can be tricky) or use a jumper with the compatible connectors on each end (like SC-to-ST, SC-to-LC, whatever).
It's usually bad practice to use multi-mode fiber in a single mode application or vice-versa.
For multi-mode applications, you may get difference performance for the different flavors; 50/125 MMF tends to get longer distance than 62.5/125 for GigE.
Good Luck
Scott

Fiber optic cable part number for s6500

Hello
I need help because i have Catalyst S6500 24 port X2-10G-SR card but i cant find Fiber optic part numer to conect.
Does anyone know the part number?
Thanks

With what type of fiber connectors is the fiber you had installed terminated? SC, LC, ST? Is it terminated at fiber patch panel. Also, do you know what type of fiber they installed? Post a picture and it should be straightforward to tell you what you need. Since your running 10G LRM you should use OM3 multimode (OM4 is ok too), hopefully that is what's installed.
So you'll need OM3 jumper cables of sufficient length to get from your Meraki to the patch panel (if they installed one). The SFP+ end of the jumper will have dual-LC connectors and the other end, whatever they have at the optical patch panel.
Definitely post a pic.
Cheers.

Fiber Optic cable types

Hello
What are the differences between the following cable types. What does Âµ and mm 50mm or 62 etc 125Âµ values determine? Where to use which?
Dorax 8 Core MM 50/125Âµ F/O
DR-5613-12 Dorax 12 Core MM 62.5/125Âµ F/O
DR-5613-24 Dorax 24 Core MM 62.5/125Âµ F/O
DR-5613-4 Dorax 4 Core MM 62.5/125Âµ F/O
DR-5613-8 Dorax 8 Core MM 62.5/125Âµ F/O
12 Core SM 9/125Âµ F/O
Dorax 24 Core SM 9/125Âµ F/O
DR-5913-4 Dorax 4 Core SM 9/125Âµ F/O
DR-5913-8 Dorax 8 Core SM 9/125Âµ F/O
Thanks

Typically, the fiber ends are terminated into a patch panel, using SC or LC connectors. Then jumpers attached to the patch panel to the equipment.
A pigtail is just a fiber with one enter terminated with a connector and the other end a bare fiber. You can splice (fusion or mechanical) the pigtails to the fiber cable ends and install them in a patch panel.
It is difficult to install connectors on singlemode fibers so installers purchase factory made pigtails or they purchase preterminated patch panels to terminate (connectorize) the fiber.
Connectors can be attached to multimode fiber in the field using polishing equipment or special mechanical connectors (depending on the volume of connectors).
There are all sorts pre-terminated products (cables, connector modules, patch panels, etc) on the market that reduce the need for the user to field terminate the fiber ends.
I've attached a couple of links, one for product and one for fiber basics.
Enjoy!
Panduit Fiber Products
http://www.panduit.com/Products/ProductOverviews/FiberSystems/index.htm
Fiber Optic Association
http://www.thefoa.org/tech/ref/index.html

Connecting iPod to stereo with fiber optic cable???

My kingdom for the right answer to this question.
I'm brand new to the whole iPod scene. Just bought an 80GB video iPod and I want to use it with my stereo system instead of the old bulky 200 CD carousel.
I see that I can connect the iPod and stereo using the AV connection kit, but isn't there a way to get digital audio sound quality with some sort of fiber optic connection?
Will the Monster iCable Fiber Optic Kit work? It doesn't list the iPod as a use, but it sure looks like the non-Fiber optic end would fit into the iPod headphone jack.
If anyone knows, I'd greatly appreciate the help. I'm a total newb about this and haven't had any luck with my online searches.
Thanks in advance.

No you cant do it but
http://discussions.apple.com/thread.jspa?threadID=863621&tstart=180

Which fiber optic cable to use for Meraki to fiber link?

Is it possible to create an automation that would move certain emails into their groups, for EG if an email comes from [email protected] that email must automatically go into a group or an organization called test. Is this possible?
Thank you
Stuart

While preparing to demote a DC I ran dcdiag and it's failing while attempting to register records in our external dns server at rackspace. I can only assume that since we use the same domain externally, and for AD, that the domain controller is seeing rackspace as authoritative and attempting to create the test records there. Has anyone seen this behavior before? It's never been a problem until now, and this issue did not appear in the logs when I demoted another DC earlier tonight.
Log:TextAn error event occurred. EventID: 0x0000168E Time Generated: 11/15/2010 15:37:52 Event String: The dynamic registration of the DNS record 'ForestDnsZones.contoso.com. 600 IN A 192.168.1.234' failed on the following DNS server: The DNS server it goes on to list is the public IP of our rackspace DNS.There are many of these errors listed as it attempts...

Broadband connection to fiber optic cabling

I understand that my local exchange in twyford hants maybe connecting to FTTS today,however i cannot find out when I will have the chance to upgrade .there is a new box at the end of our road but the one 80 metres away is an old box and i want to know when it will be connected.so far its impossible to get an answer.so how can i find out a date.

You can find out from this link you need to look for FTTC services http://www.dslchecker.bt.com/adsl/ADSLChecker.TelephoneNumberOutput
although an exchange goes live not al cabinets go live at the same time it can sometimes be several months before all do
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Component Video Cables vs. Fiber Optic?

I am looking to purchase a Sony HTS-S360 Home Theater system sometime in the near future and I am looking to hook my 46" Sony Bravia XBR9 up to it. I am wondering which would be better for such a setup, Component Cables or a Fiber Optic Cable. I want whichever gives me the quality of sound closer to the HDMI cable but I also don't want to pay the extra money for an HDMI cable. Any suggestions for which would be the better way to hook the Sony receiver up to my Sony TV?

Well for starters one is a video cable and the other is audio. Component cables carry video on three different cables, red, green and blue. Optical cables carry digital sound. So if you went with component cables to hook something up like a cable box or dvd player you would also have to use the optical cable for sound. So is not one or the other, its both since one does video and the other does the audio.
HDMI carries both digital video and audio.
What are you looking to hook up with this new system? It doesn't come with a blu ray or dvd player built in. So you will have to get one seperately if you don't have one. And do you have a cable box or satalite dish? This system has HDMI inputs so if you want the best quality I suggest using them. If your just looking to get sound from the tv to the receiver you would run an optical cable from the tv audio out to the optical in on the receiver.
Let us know what components you have or play on buying and maybe we can help you with the best way to hook it up. If you get a blue ray player using component cables will not be the best way to hook it up. To gain the full advantage of blu ray you will need the HDMI cable.

What is best fiber optic to analog converter to use with RCA cables to receiver?

What is best fiber optic to analog converter to use with RCA cables to receiver?

OK, in that event I would get a Toslink to analog converter. There are many sources for these, such as Monoprice and Amazon. They are not expensive.
The fiber optic cable itself is incredibly cheap. Practically free. Don't spend a lot of money on one.

ATV2 Connected with HDMI for video and fiber optics for Sound but unable to located the fiber optics option in ATV2

hello everyone, I currently have my ATV2 connected from HDMI to my TV for Audio&Video but I want to run just my HDMI for Video and my Fiber optics cable for my Sound. I am unable to locate in the settings where I can change my sound to Fiber optics output.
Thank you
Steve

ok so I figured it out.. I just needed to go into my surround sound and select optical out.

Fiber Optic Power lvl

I own a 20" Imac (2006) for 3 years I have been using the fiber optic output to my receiver via a 3 port fiber optic switch shared with a windows cpu and my tv. It took me about 6 different types of switches that to find one that did not reduce the signal to the point it was inoperable.
About 6 months ago it just decided to stop working I assumed the cable had been damaged due to a 1 year old yanking on it. So I put off investigation until I got around to obtaining a new cable 10' (old was 10'as well) when I replaced the cable, however, it still would not work.
I figured my switch had gone bad or something so I then checked the other devices just to be sure they still worked. I even switched to the port the Imac was using with no problems (using the new and old cables that were for the Imac). I can bypass the fiber switch and plugged the Imac directly into the receiver with no problems. While not detrimental I used to enjoy not having to expose my fiber ends to potential danger of contamination or damage. Not to mention not having to reach behind my receiver when I want to switch devices.
I do realize my problem ma be a bit unique but has anyone heard or know if a update has recently lowered the power output of the Imac's TOSLink output port? Or if anyone knows of a better fiber switch with 3 ports that may have less loss I have tried 6 ranging from $9.99 to $78 the one I am using is
http://www.amazon.com/gp/product/B0014Z29RW/ref=pdlpo_k2_dp_sr_3?pf_rd_p=486539851&pf_rd_s=lpo-top-stripe-1&pf_rd_t=201&pf_rd_i=B0 00812QC6&pf_rd_m=ATVPDKIKX0DER&pf_rdr=11S9KZYH7K9B3BJ8QPHB
Any help or input would be greatly appreciated

I haven't heard of anything about an alternate power source for Digital Voice. I don't see how that is possible considering Digital Voice essentially works just like FiOS POTS does. The ONT still needs to be powered by the Battery Backup or AC Power, and that's all that would be to it.
Now that you have FiOS, it's going to be difficult to get the Copper service reconnected. Verizon will not normally reconnect the copper unless there's something extreme or there is a medical need that requires the assurance of a copper line. You can ask around to see if you can get it connected or not, but failing that, I would invest in a small generator (tiny camping one, power draw is basically idle run lol) to keep the ONT powered up as needed for the phone service, if it is at all possible to do. The Fiber Optic cabling will remain lit since the Central Office should remain powered off of Diesel Generators/Turbines/Batteries for quite a while.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Can't see others in iChat over Fiber Optic connection

This was a strange, recent occurence. For the past few years, those of us on Macs (G5's and a PowerBook with latest OS and updates) have been able to communicate via iChat. With new offices, most Mac users went to the new building. I'm still in the old building where the network server is kept. Once the others moved, we are no longer able to see each other via iChat. The only exception are two stations in the same office which share the same Ethenet wall connection.
Bringing any station back into the old building and connecting to the network will allow this station and my station to see each other, so I've narrowed the situation to our cable connection from the new building to the network server here in the old building. The cable used to bridge the two buildings is a Belkin 3 meter Multimode LC/ST Duplex Fiber Optic Cable.
I am able to see other Macs on the network through the Finder. I've just lost iChat and VNC capabilities since we've gone to this connection. If anyone has any ideas on how to correct the situation, whether they be adjustments to the Macs' Network settings or ideas of proven alternatives to the connection, all would be appreciated.
Thanks.
G5 Mac OS X (10.4.8)

Hi DrVvack,
Welcome to the Apple Discussions
It is likely that the computers in the new building are in a different subnet of the LAN
Lets say you are at 192.168.1.100.
Others in your building also start 192.168.1.xxx
The other building is likely to be on a router for that building. Now the router is probably at an IP that is in the same group as your computer - but it will be issuing IPs of it's own.
Now a bit like street numbers this other router could be using a similar set of IP addresses (192.168.1.xxx) but it is the IPs in relation to the original routing device that makes a difference.
You can get around this by creating a Virtual Private Network then the Bonjour side of iChat will see everyone.
Another option is to have the second router in Bridge mode or Access point mode (not routing) and have everyone have an IP from the original device.
10:41 PM Wednesday; February 14, 2007

Interdepartment connectivity via fiber optics, which wquipment to use

I have given a task to interconnect department with one another via fiber optics.
This means there will be a core switch in a server room which will interconnect these departments. The each departments are away from server room approx 900 meters and 1500 meters. Kindly tell me which fiber optics cable to use ( single mode or multi mode) and which cisco switch to use in the in the core ( server room) and in the departments (one deptt is 900 m and other is 1500 meters away from server room) . kindly also tell me which fiber optics module to use in the switch and which connector.

Since in both cases you are well within the reach of multimode fiber, it makes no sense to look any further, as it is the most cost effective solution unless you need 10 gigabit performance.
As to what switches to use, there are a lot of variables once you get past the basic requirement here of having of having two optical ports on the one in the server room, and one optical port for the other two. Other considerations are how many ports do you need in the server room, and in each of the two departments. Then features, performance, and reliability factors come into play, along with budget.
If you don't need a lot of ports, and you are looking at normal office levels of traffic, 3560's might be a good choice. You could put a second one in the server room, and duel home the servers and department switches to them to add redundancy. That would make a single switch failure unlikely to take out the whole network at one time. One the other hand if you need hundreds of ports, have a mission critical situation, or expect intensive levels of data traffic, then you will need to look at high end switches such at the 4500 and 6500 series.

Trace Fiber Optic Cables

Similar Messages

Maybe you are looking for