Trackpad acting funky but mouse okay

Okay so suddenly after having my 12" 867 PB for almost 3 years my trackpad is acting up. Its almost acting elastic like I can only move the pointer out so far before it snaps back. If I don't have my finger on it the pointer just kinda wobbles in place a little. If I plug in a mouse the mouse works fine but if I still have the trackpad enables it wobbles while the mouse is plugged in but otherwise works. If I click ignore trackpad while mouse is plugged in the wobble goes away. If I use the mouse anywhere from a few seconds to minutes then unplug the mouse the trackpad then seems okay for a while...then out of the blue it starts acting up again (usually within minutes).
Any thoughts?

help me it's getting worse! Now I can't click anything! I restart it often but it only works for a few minutes :(

Similar Messages

  • HT201361 After taking the screenshot clicking on my trackpad just acting like right mouse click or 2 finger click. Could you help!

    After taking a screenshot command + Shift + 4, clicking on my trackpad is like right mouse click or 2 finger click. Please help!

    Maybe your trackpad battery is running low? If not I would suggest just restarting your Mac. Post again if those things don't fix your problem and some more involved problem-solving can be attempted.

  • Can I use an animated symbol acting like a mouse cursor?

    Hi,
    I'd like to use an EDGE animated symbol ( a blinking magic wand) as my mouse cursor (hiding the original cursor) that stays on the stage all the time at a certain point in the timeline and when clicked on a hotspot, goes to another point in timeline where the symbol no longer act as a mouse cursor. I used the following code suggested in the following thread by YOSHIOKA Ume
    Re: How to I have an animated symbol follow the coordinates of the cursor when clicked?
    1:create a symbol named "Symbol_1"
    2:add this code on Symbol_1-Timeline.complete.
    //delete this instance when timeline complete. sym.deleteSymbol();
    3:add this code on document.compositionReady.
    //on/off mousemove event handler method
    sym.$("Stage")  
    .mouseover(function(){    
    sym.$("Stage").on("mousemove",draw);  
    //create instance of Symbol_1 on stage.
    function draw(evt){  
    var instance = sym.createChildSymbol("Symbol_1", "Stage");  
    instance.getSymbolElement().css({    
    position:"absolute",    
    top:evt.clientY,    
    left:evt.clientX   });
    But the problem is, the symbol is being repeated/drawn one after another according to the above code, which I don't want. Changing the cursor using CSS requires a URL of a image file, not a symbol inside EDGE as it seems. How can I get back the normal mouse cursor in another point in the timeline (and go back to the animated symbol mode again if needed?). If I click on another hotspot element on the stage, do I actually click on the attached symbol as a cursor? Or the hotspot?
    Also, how can I put a constraint on the cursor so that it stays within a certain rectangular area smaller than the stage?
    A suggestion is much appreciated.

    Here is a example I had to move a symbol around as a mouse cursor and play different part of the symbol timeline based on user action.
    mouseCursor.zip - Google Drive
    To constraint the symbol to stage area,check for the x and y values in the event callback function before moving the symbol.
    To get back the normal cursor set the css back to default
    ex: sym.getSymbol('Stage').getSymbolElement().css({ 'cursor' : 'default'});

  • I have an IPhone 4, and I wanted to reset it, but couldn't do it via computer because the "find my IPhone" was turned on. So I went to ICloud Find My IPhone and just erased my phone from there. The was acting weird but I finally got to a black scre

    I have an IPhone 4, and I wanted to reset it, but couldn't do it via computer because the "find my IPhone" was turned on. So I went to ICloud > Find My IPhone and just erased my phone from there. The was acting weird but I finally got to a black screen with the spinning circle. And it won't advance. I can't just hold the sleep button and home button down because my sleep button is broken! Any help? I have reset my phone before.

    Hello cwypyski,
    The link below provides information on and can also assist with setting up service for your iPhone to have your Sleep/Wake button repaired.
    Service Answer Center - iPhone
    http://support.apple.com/kb/index?page=servicefaq&product=iphone
    All my best,
    Allen

  • Installing windows 8 with bootcamp 5. Have to make a choice at personalize but mouse is not working.  What can I do?

    installing windows 8 with bootcamp 5. Have to make a choice at personalize but mouse is not working.  What can I do?

    I solved my problem by using a USB mouse and a USB keyboard instead of bluetooth

  • All of the sudden my keyboard is not working.  the trackpad is working, but i can't enter any letters/numbers?

    all of the sudden my keyboard is not working.  the trackpad is working, but i can't enter any letters/numbers?

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Restore from backup. See:                                 
    iOS: How to back up           
    - Restore to factory settings/new iOS device.
    If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem. Likey a bad digitizer
    Apple Retail Store - Genius Bar          

  • Thought my computer was acting up- but I see there are other people with issues with the extension mgr.  Hope it's up and running soon!

    Well, I thought my computer was acting up, but I see there are others with extension manager issues! Any ideas when it will be accessible again?

    The flashing folder/question mark means the computer can't find a volume to start up from. See this Apple article for steps to take. But since it was running very slowly, I won't be all that encouraging that this can be resolved using those steps. It probably means the internal hard drive died. The slowness may have been a warning it was about to fail.
    http://support.apple.com/kb/TS1440
    PS>>> I also have an external hard drive if that helps!
    Well, it may help enormously if you had all your data backed up there to restore from, if it is clear you need a new internal drive. What kind of backup was it, a clone or Time Machine?

  • Installed Window 7 on DV6700 but mouse movement not smooth as before

    Installed Window 7 on HP DV6700 but mouse movement not as smooth as before. When you move your finger on the touch pad  but the pointer does not move along as smooth as it should. Is it because of driver problem? if yes then is there a more suitable driver to use and where can I download it?
    When I used it with Window Vista ,there was no problem. Thanks.
    One more things, there is no longer the beep sound when you press the sound button to increase or decrease the sound. The buttons on top of the keyboard. Do I need to download another driver?

    Synaptics touchpad here
    For the click sound, you need either HP Quick Touch from your Vista drivers page or 3RVX here .
    ******Clicking the Thumbs-Up button is a way to say -Thanks!.******
    **Click Accept as Solution on a Reply that solves your issue to help others**

  • Trackpad won't move mouse but will do gestures

    My trackpad is connected and registers clicks and all multi-touch gestures, but will not move the mouse when a single finger is moved across it. It is a little over one year old. I tried cleaning the surface just in case but that didn't work. Batteries are at 83% and, since it will register other gestures, I know that is not the issue.
    What is going on with this device?

    Okay, I synced it up to a macbook pro and the trackpad worked perfectly. So it looks like there must be some issue with my mac mini which is not good. Any ideas about what to do or should I just take it into the Apple store?

  • Trackpad acting weird after using mouse.

    After an extended time using the mouse, my trackpad becomes, in a way, unresponsive.
    If I hover the cursor above links, edge of windows or applications in the dock, my cursor stays as the same arrow and the link won't underline and applications on the dock won't show their names.
    Also, when I move the mouse while using the trackpad, the cursor snaps back to where it was when using the mouse.
    It isn't anything serious, but it's certainly an annoyance.
    Thankyou.

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
    The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

  • Wireless Keyboard losing connection - Mouse acting funky

    I keep getting a "connection lost" message and then have to "wake up" the keyboard. I just changed the batteries in both the wireless mighty mouse & wireless keyboard. The mouse keeps getting very "choppy" and unresponsive, then straightens out after a few minutes. Also lots of keyrepeats. The problem has been here for a while but seems to be getting worse. All software & firmware is up to date. When I turn on the keyboard the light only stays on for a few seconds then goes out.
    Dave

    There should be four tiny wires with round connectors, each labelled "1" "2" "3" and "BT". 1-3 are for the Airport card and BT is for Bluetooth.
    Try these pics to help you to identify the cable and the bluetooth module:
    http://www.xlr8yourmac.com/systems/MacPro/Bluetooth_MacPro_install/Bluetooth_MacProinstall.html

  • Trackpad acting up after USB mouse use

    I was using a wireless mouse to do homework and everything was fine. I left my computer alone for about an hour and when I came back, my cursor wouldn't move at all, with the mouse in or with just using my trackpad. Now, I have taken out the USB for the wireless mouse and my trackpad is sporadically moving around and barely responds to my touch at all. When it does respond, its movements are jerky and the cursor does not go where I am leading it. I have tried restarting the computer, turning off blue tooth and Airport, and I don't know what to do next. Everything was fine until I left the wireless mouse connected. I have used this mouse hundreds of times and it was fine. Please help!

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
    The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

  • The office suite shows up twice on the bottom--I need to uninstall and reinstall it but now it still shows up twice; documents act funky and load again when I pick the other icon--how can I reinstall completely so just one office suite in indeed installe

    I put office for MAC on my macbook air--it somehow shows up twice and documents load out there depending on which one you pick. I need to get all of the office installiations off and reinstall but it appears to leave one out there. When I go to applications I cannot see it but I can see it on the icon line on the bottom of the screen. How can I reinstall Office for Mac so there is only one installation on my computer ?

    Unfortunately the information given to you by r8er is incorrect, deleting the Office folder from Applications only partially uninstalls Office.
    Here are the correct uninstallation instructions for you.
    And the icons at the bottom are just shortcuts.

  • Make T440s trackpad act like the older one? - disable touch but keep buttons?

    Is there a way to disable the "touch" portion of the new T440s trackpad - while keeping the "button" functionality?  I'm a big fan of the trackpoint plus the two discrete buttons (Like my old T420/430s had), and if there is some way to disable everything EXCEPT the "soft buttons" on the new T440s... then I can get very very close to the old behavior... any thoughts on whether this is possible?

    Yes, this is possible:
    - Disable the TrackPad in BIOS
    - Enable "Classical TrackPoint only Mode" in the driver

  • Keyboard & Trackpad not working but USB are...

    Hi - 2007 white Macbook, 10.6.8...
    Today the machine appeared to keep freezing completely... after numerous checks (including booting in 10.5), it transpired it was the keyboard and trackpad that weren't responding, not the OS. I know this because I plugged in a USB keyboard/mouse to check and they work fine.
    That said, the onboard keyboard & trackpad do work upon boot up for anything from 1 to 10 minutes. Then they just stop responding and I have to resort back to USB again. I can see others who've had similar problems but I can't find a solution.
    It doesn't appear to be a fatel hardware error because they will always work on boot up for a limited time. All updates are applied and disc permissions repaired.
    Anyone know how to solve this? Appreciate the help - stars all round, thanks.

    It doesn't sound like a fatal hardware issue but I think your Top Case Assembly or the connection cable are going bad. The top case is basically the plate containing your keyboard, trackpad, and power button.
    The fact that it works via USB basically confirms that, but there is the outside shot that the connector on the Logic Board could be the problem....
    Before you take it to an Apple Store, try to boot it up from your software discs that came with your Mac (disc #1, you can do this by restarting your Mac with the disc in and holding down the C key after the startup chime) and see if the problem occurs. If it does, I would have an Apple Service Provider or an Apple Store replace your Top Case for you.If it's okay on the discs, run your Disk Utility on the software disc and reinstall the OS.
    I hope this helps!

Maybe you are looking for

  • I corrupted the firefox profile file using profile manager and firefox thinks it is still running and asks me to close but there is no instance of it running...I have tried several re-installs but cannot resolve the problem....

    .........I have deleted the .ini file associated with the profile file and the profile file itself...have tried to locate the "lock" file but cannot find the file in the specified path on the support forum for this problem....I believe there is a fil

  • Best Log Setting for ASA & MARS

    Hi, I'm going back and trying to clean up our MARS install a little bit now that I have some time. I need to update MARS to the latest version, but right now I'm just trying to wade through some of the undefined logs coming from our ASA. Is there any

  • Proforma

    Hi, Issue of this is that the ZPRS (copy of VPRS) of billing type YWIA and proforma should be the same. But in my case, it is different. I have an invoice with billing type of YWIA. The amount in ZPRS (copy of VPRS) is 21,833.20. while the proforma i

  • Applet Init Performance

    Hi, I am new to Applets. Every time I access an Applet browser downloads all related classes. Can I do something so that if the classes are not modified then the browser uses the cached copy instead of downloading again and again? Thanx in advance. S

  • Rate limit a CQC?

    I would like to be able to shovel objects into a cache as fast as the storage enabled server nodes can digest them but not overload my clients listening with CQCs. It would be nice if when you create a CQC you can specify a max receive rate. Currentl