Transfering files between devices

Good morning,
What are the various means to transfer files (photos, movies, books, documents) from my iMac to my iPad/iPhone and vice versa, without synchronising the devices with my iTune library. For instance I would like to load a movie I have on my iMac onto my iPad, but I don't want to do that via synchronising my iPad with my iTune library.
Can I use Air drop ?
Can I use blue tooth between the iMac and the iPad ?
Many thanks,
P0mme

Similar Messages

Is there a way to turn off using ram as intermediary when transfering files between 2 internal hdds? (write cache is off on all drives)

right forum? first time here. none of the options seem perfect. so i guess this applies to 'setup.' i tried to describe what's happening verbosely from the start of a file transfer to completion of writing file to 2nd hard drive.
win 7 64bit home - i2600k 3.4ghz - 8gb of ram - 2hdd 1 ssd
I have this problem when transferring files between 2 internal hard drives. one is unhealthy (slow write speeds but not looking for advice to replace it because it serves its unimportant purpose). so, the unhealthy drive drops into PIO mode - that's acceptable.
however, a little over 1gb of any file transfer is cached in RAM during the file transfer. after the file transfer window closes, indicating the transfer is "complete" (HA!), it still has 1gb to write from RAM which takes about 30minutes. This would
not be a problem if it did not also earmark an additional 5gb of ram (never in use), leaving 1gb or less 'free' for programs. this needlessly causes my pc to be sluggish - moreso than a typical file transfer file between 2 healthy drives. i have windows write
caching turned off on all drives. so this is a different setting i can't figure out nor find after 2 hours of google searches.
info from taskmanager and resource monitor.
idle estimates: total 8175, cached 532, available 7218, free 6771 and the graph in taskman shows about 1gb memory in use.
at the start of a file transfer: 8175, 2661, 6070, 4511free and ~2gb of ram used in graph. No problems, yet.
however, as the transfer goes on, the free ram value drops to less than 1gb (1gb normal +1gb temporary transfer cache +5gb of unused earmarked space = ~7gb), cached value increases, but the amount of used ram remains relatively unchanged (2gb
during transfer and slowly drops to idle values as remaining bits are written to the 2nd hard drive). the free value is even slower to return to idle norms after the transfer completes writing data to 2nd hard drive from RAM. so, it's earmarking an addition
5gb of ram that are completely unused during this process. *****This is my problem*****
Is there any way to turn this function off or limit its maximum size. in addition to sluggishness, it poses risk to data integrity from system errors/power loss, and it's difficult to discern the actual time of transfer completion, which makes it difficult
to know when it's safe to shutdown my pc (any data left in ram is lost, and the file transfer is ruined - as of now i have to use resmon and look through what's writing to disk2 -> sometimes easy to forget about it when the transfer window closed 20-30minutes
ago and the file is still in the process of writing to the 2nd disk).
Any solution would be nice, and a little extra info like whether it can be applied to only 1 hard drive would be excellent.

Thanks for the reply.
(Although i have an undergrad degeee in computers, it's been 15years and my vocab is terrible. so, i will try my best. keep an open mind. it's not my occupation, so i rarely have to communicate ideas regarding PCs)
It operates the same way regardless of the write-cache option being enabled. It's not using the 5gb for read/write buffer - it's merely bloating standby memory during the transfer process at a rate similar to the write speed of destination (for my situation).
at this point i don't expect a solution. i've tried to look through lists of known memory leaks but i dont have the vocabulary to be 100% certain this problem is not documented. as of now it can't affect many people - NAS's with low bandwidth networks, usb
attached storage etc. do bugs get forwarded from these forums? below i can outline the consistent and repeatable nature not only on my pc but on others' pcs as well (2012 forum post i found).
I've been testing and paying a little more attention and i can describe it better:
Just the Facts
Resmon Memory Info: "In Use" stays consistent ~1gb (idle amount and roughly the same when nothing else is running during file transfer)
"Modified" contains file transfer
data (meta data?) which remains consistent at little over 1gb (minor fluctuations due to working as a buffer). After the file transfer window closes "Modified" slowly diminishes as it finishes lazy writing (i believe that's the term). I forget idle
pc amount, but after transfer this is ony 58mb)
"Standby" as the transfer starts it immediately rises to ~2gb. I'm sure this initial jump is normal. However, it will bloat well over 5gb over time with a large enough transfer increasing at a consistent rate during the entire transfer
process. the crux of the matter.
"Free" will drop as far as 35-50megabytes over time.
as the transfer starts, the "Standby" increases by an immediate chunk then at a slow rate throughout entire transfer process(~1mb/s). once writing metadata to RAM no longer occurs, the "Modified" ram slowly (@500kb/s matching resmon disk
activity for that file write) diminishes as it finishes lazy writing, After file is 100% written to destination drive, "Standby" remains a bloated figure long after.
a 1.4gb transfer filled 3677MB of "Standby" by the time writing finished and modified ram cleared. after 20minutes, it's still bloated at 3696MB. after 30-40mins it's down to 2300mb - this is about what it jumps immediately to when transfer starts
- it now remains at this level until i reboot.
I notice the "standby" is available to programs. but they do not operate well. e.g. a 480p trailer on IMDB.com will stop-and-go every 2-3seconds (stream buffers fine/fast) - this would be during the worst case scenario of 35-50mb "Free"
ram. my pc isn't and never was the latest and greatest, but choppy video never happens even with 1 or 2 resource hogs running (video processing/encoding, games, etc).
Conjecture Below
i think it's a problem when one device is significantly slower at writing than the source device - this is the factor that i share with others having this problem. when data is written to modified ram then sent to destination, standby memory is expanded
until it completely or nearly fills all available RAM - If the transfer size is large enough relative to how slow the write speed of destination device is. otherwise it fills it up as much as the file size/write speed issue allows. the term "memory leak"
is used below but may not technically be one, but it's an apt description in layman's terms.
i saw a similar post in these forums (link at end). My problem is repeatable and consistent with others' reports. I wasn't sure if i should revive it with a reply. some of these online message boards (maybe not this one) are extremely picky
and sensitive, lol.the world will end if an old thread revives - even if for a good reason.
i can answer some of the ancillary issues. one person (Friday, September 21, 2012 8:33 PM) mentions not being able to shutdown, i asume he means stuck on the shutdown screen - this is because lazy writing has not completed - his nas write speed is significantly
slower than reading from source - the last bits of data left in ram still needs to be writen to the destination. shutdown will stall for as long as needed until the data finishes writing to destination to prevent data loss.
another person (Monday, September 24, 2012 6:31 PM) mentions the rate of the leak, but the rate is more likely a function of read speed from source relative to write speed of destination. which explains why my standby expands closer to a 1:1 ratio compared
to his 1:100 (he said 10mb per 1000mb)
we all have the same exact results/behaviour, but slightly different rates of bloating/leaking. as the file is written from from the ram to the destination, standby increases during this time - not a problem if read and write speeds are roughly equal (unless
your transfering a terabytes then i bet the problem could rear its head). when writing lags, it gives the opportunity for standby ram to bloat with no maximum except the amount of installed ram. slower the write speed, the worse the problem.
The reply on Wednesday, September 26, 2012 3:04 AM has before and after pictures of exactly what i described in
"Just the Facts". Specifically the resmon image showing the Memory Tab.
The kb2647452 hotfix seems to do some weird things relative to this problem. in the posts that mention they've applied it: after file completes it looks like the "standby" bloat is now "in use" bloat. as per info from Tuesday, October
09, 2012 10:36 PM - bobmtl in an earlier post applies the patch. compare images from earlier posts to his post on this date. seems like a worse problem. Also, his process list indicates it's very unlikely they add up to ~4gb as listed in the color coded bar.
wheres the extra gb's coming from? likely the same culprit of what filled up "standby" memory for me and others. it looks like this patch relative to this problem merely recategorizes the bloat - just changes the title it falls under.
Link:
https://social.technet.microsoft.com/Forums/windows/en-US/955b600f-976d-4c09-86dc-2ff19e726baf/memory-leak-in-windows-7-64bit-when-writing-to-a-network-shared-disk?forum=w7itpronetworking

Transfering files between macs

I am trying to transfer files between my G4 powerbook and new macbook.
For some reason the powerbook will not reboot if I hold the "T" down after I clicked restart.
Any Suggestions?

tried starting it up in TDM, but would not start .
Tried it with cable connected and disconnected. Tried shutting it down completely, but nothing.
Seems to be a bug in it.

Difficulties transferring files between Lion and Leopard

Hello all-
The short: Our two computers running Leopard can transfer files across our home network to all other computers with no problems, and can grab files from other computers with no problems. Our new iMac Lion can't do any of that.
The long: We have recently purchased a new iMac (Lion 10.7.3), and have connected our old 2006 iMac (Leopard 10.5.8) to the TV and stereo (and directly to our B/G/N Airport Extreme) for use primarily as a media server. We also have an MBP (Leopard 10.5.8). All three computers are shared on a home network, and I believe I have set up the sharing and permissions correctly.
From both Leopard computers I can transfer files back and forth, as well as access files on the other and bring them over. Additonally, from both Leopard computers I can do the same while accessing the iMac Lion- either transfer files to it, or connect to it and bring files over. This is what leads me to believe that the sharing is set up correctly.
However, when I am on the iMac Lion and try to do any of these processes with either of the Leopards, I get a confusing set of steps and ultimately, failure.
First, I when I try to transfer or copy a file I get a window asking:
Finder wants to make changes. type your password to allow this.
It automatically fills in the admin username for the iMac Lion. While it is waiting for me to enter the password, a progress bar pops up stating that it is "Preparing to copy to "(Location)", and then I enter the password.
As soon as I enter the password, a new window tells me that:
A newer item named “(filename here)” already exists in this location. Do you want to replace it with the older one you’re moving? (note- this 'file' has just been created, it is the 'newer item', and it contains zero kb of information).
and gives me three options: Keep both files, Stop, or Replace
If I choose Keep both files it immediately begins duplicating the empty version of the file and it will make thousands of duplicates in mere seconds. I must kill Finder in order to make it stop.
If I choose Stop the process simply quits.
If I choose Replace it says The operation can’t be completed because an item with the name “” already exists. (the quotation marks are exactly like that with no filename inbetween).
Summary: I am at a loss as to how to proceed. I cannot seem to find why the iMac Lion cannot do anything to the Leopards, while the Leopards seem to have full abilities, even with the Lion. I have tried turning off AFP and turning on SMB to no avail.
Any advice would be greatly appreciated. It is incredibly helpful to be able to share files between our systems, as the iMac Leopard has PPC programs that I cannot install or run on Lion, and so I keep them around in case I need them. Plus, my wife uses the MBP Leopard for specialized research and many of the programs they use do not run with Lion.
Message was edited by: Jeff Sorley

Repairing the permissions of a home folder in Lion is a complicated procedure. I don’t know of a simpler one that always works.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the page that opens.
Drag or copy — do not type — the following line into the Terminal window, then press return:
chmod -R -N ~
The command will take a noticeable amount of time to run. When a new line ending in a dollar sign ($) appears below what you entered, it’s done. You may see a few error messages about an “invalid argument” while the command is running. You can ignore those. If you get an error message with the words “Permission denied,” enter this:
sudo !!
You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning not to screw up.
Next, boot from your recovery partition by holding down the key combination command-R at startup. Release the keys when you see a gray screen with a spinning dial.
When the recovery desktop appears, select Utilities ▹ Terminal from the menu bar.
In the Terminal window, enter “resetpassword” (without the quotes) and press return. A Reset Password window opens. You’re not going to reset the password.
Select your boot volume if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select  ▹ Restart from the menu bar.

Transferring file between two mac os 10.7.5 computers

what do i need to trsansfer files between two mac os 10.7 computers on the sqame network and I want to do this over the wireless network?

Hope this helps.
If both computers are using OS X Lion or OS X Mountain Lion, use AirDrop to send files wirelessly to those near you.
http://support.apple.com/kb/PH11466

Transferring iTunes between devices

I reloaded iTunes from the Apple.com site and have the next to newest software on my iPhone.
I finally am able to 'see' iTunes on my laptop but when I try to download the tunes from my iPhone, they are not highlighted.

Hello there, clarencetoo.
It sounds like you're trying to get your content transferred from your iPhone to your iTunes Library on your computer. The following Knowledge Base article offers up how to do just that:
Re-download or transfer your iTunes Store purchases from an iPhone, iPad or iPod to a computer - Apple Support
Transfer your purchases to your computer
Before you transfer your purchases, make sure that your computer is authorized with the same Apple IDaccount you used to make the purchases. Learn how to authorize your computer using iTunes.
If you bought the iTunes Store content on your device using multiple Apple ID accounts, you'll need to authorize the computer for each one.
To transfer purchases from your device to a computer:
Connect your device to the computer. Wait for its icon to appear in iTunes.
Go to File > Devices. If you're using iTunes for Windows and can't see the menu bar, learn how to turn on iTunes menus in Windows.
Choose Transfer Purchases from [device name].
This feature works only for content bought from the iTunes Store. Any items that you imported from audio CDs or received from other sources won't copy from your device to the iTunes library. However, all podcasts from your device's Podcasts app and copies of all PDFs and books from your device's iBooks app will transfer to the computer. Learn how to transfer media to your iTunes library.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Transferring files between MacBook Pro and PC

First, what's the best way to copy files back and forth between a MacBook Pro and a 5-year-old Dell PC? Would I use a "firewire"? (Is that the same thing as a USB?)
Next, I've heard that there's some way to automate the process so that you can copy and paste or drag and drop an item to a certain location on one computer, and it's automatically transported to a certain location on the other computer. For example, suppose I'm modifying some Dreamweaver files on my PC, and I want to copy them a local website on my MacBook. Can this be done?
I have an external hard drive that I use to back up data from my PC. I discovered that I can connect it to my MacBook. However, it's a somewhat tedious process.
Thanks.

In actual fact the simplest is just to use a flash USB thumb drive.

Transferring files between Creative play

I have both a zen micro and a jukebox 3. If I have wav. file recordings on my JB3 can I transfer them to my zen?
From there can I move them to my pc?
how do I go about doing that?
thanks a ton for any help!!!
jackfee

You can use Creative MediaSource to do that. Just view the JB3 in one panel and Zen Micro in the other panel. Select the tracks to be transferred and click the transfer arrow.
Let me know if you need more precise ste
ps.

Transferring music between devices

Hi,
I just bought an album on iTunes on my iPad, how do I get this album on my iPhone, it's the same apple ID

You might be able to re-download it on iPhone via the Purchased tab in the iTunes store app on it : re-downloading.
If you aren't in a country where music can currently be re-downloaded then you will need to connect the phone to your computer's iTunes and copy it over via File > Transfer Purchases (File > Devices > Transfer Purchases), and you then sync it to your iPad.

Transferring files between iMac and Mac Air

My daughter gifted me a new but older Mac Air (mid 2011). I tried to transfer files from my existing iMac (2008) to Mac Air using migration assistant, but the connection never happens. What am I doing wrong?

It sounds like you were attemting the transfer over a network. Try creating a Time Machine backup (or updating the one you have) and use that with Migration Assistant. It is faster and more reliable. You need a Time Machine backup anyway so if you don’t have on this is the time to create one. Create one (or more) for each machine.
For more about backups
Time Machine Basics: http://support.apple.com/kb/ht1427
Most commonly used backup methods:
https://discussions.apple.com/docs/DOC-3045
Methodology to protect your data. Backups vs. Archives. Long-term data protection
https://discussions.apple.com/docs/DOC-6031

Transfering files between computers

I have just ordered an iMac G5 1.9 ghz 17" computer and need to transfer my files from my eMac 700 to the new iMac G5. I also ordered a firewire male to male cable for the transfer. Any suggestions for how to do it so that, other than system software, all my programs and data will be duplicated? I have Drive Genius 1.1.5 and also use SuperDuper for my backups.
eMac 700 Mac OS X (10.3.9)
eMac 700 Mac OS X (10.3.9)

Welcome to Apple Discussions!
Since you are backed up, you can use the Migration Assistant on the new machine:
http://docs.info.apple.com/article.html?artnum=25773
when hooked up to the old machine with the Firewire cable you mentioned.

Very slow speed during transferring files between two MacBook Pro by AirPort

I have a MacBooc Pro md101 and my friend have MacBook Pro early 2011 model, when we transfering something a speed is very slow,3 month ago i've the same model like his model ( Early 2011 ) and speed was very fast by airport, but now is slow ! Anyone help me or say why ? Thank you...

If it is wireless to wireless transfer it will go at less than half of the slowest connection..
Check each mac link speed to the Express.. if either of them is far away or using 2.4ghz instead of 5ghz you will lose lots of speed.

Question about transfering files between windows OS and mac OS when using bootcamp

I'm thinking about buying the latest macbook pro, however, many of the statistical programs I use are only compatible with windows OS. I am aware of fusion and parallels, but I was advised to use bootcamp to maximize the performance of both the statistical programs AND the macbook itself. When using bootcamp, if I were to create a word document for my statistical output in the windows 7 partition, would I be able to access it directly from the hard drive in the mac OS partition using windows for mac? Any suggestions would be appreciated!

I run both Windows and OS X on my Mac. I would never ever want the Windows partition to have write access to my OS X partition. Be cautious when considering this ability. I would much prefer sharing files by a third drive, be it a flash drive, and external HDD, NAS, or an SD card.

HT201317 Transferring files between apple products

How does my iphone take pictures and it transfer to my macbook pro on icloud? I have an ipad, iphone and macbook. I cannot figure out how to make them all talk to each other on icloud even though they are all connected to the same account.

First, make sure you meet the requirements for icloud on those devices.
http://support.apple.com/kb/HT4759
If they do, and you're signed in with the same apple ID, turn on photo stream. On the macbook, in iPhoto, there is a photostream entry on the left side you can click.

Transfering files between Oses

So I have an interesting issue…at least I think it is. I have an older Mac, a Dual Proc. 867 Tower with mirrored doors running OSX 10.3.9. On this computer I have an after market internal hard drive. On this drive is all my music. The computer has gotten old and we now have a laptop running 10.5.8 and a (ghasp!) pc (I needed it for school, don’t hate).
I went to Best Buy and bought an external 1TB hard drive. My intention was to get all my tunes on this drive so I could have them play through either my Mac OR pc. But when I got home, the old Mac OS didn’t recognize the drive and I couldn’t transfer a thing. I went back to BB and they said, in short, “whoops, our mistake, you’re screwed.”
I’m not accepting that. There has to be a way to get my music off the old Mac. I was curious if there was a way I could use the tower as an external drive of some sort and hook it up to the PC. Then I all I’d need to do would be to plug the drive into the new mac and BINGO! I’d have tunes.
Am I on the right track here? If so, how do I go about it?
Thanks!

Most likely the new drive was formatted NTFS, and OS X cannot write to an NTFS formatted drive. If you want to use the drive on both computers then you have to use a format that is compatible with both platforms. That would be MSDOS. Or you can purchase third-party software for the PC enabling it to read a Mac formatted drive. This would be a preferable solution.
In any event here's what you need to do to prep the new drive:
1. Open Disk Utility in your Utilities folder.
2. After DU loads select the new hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button and select the third option, MBR. Click on the OK button. Set the format type to MSDOS. Click on the Partition button and wait until the process has completed.
This will partition and format the drive for MSDOS and can be used on both platforms. Note that MSDOS is not fully compatible with Mac files so I would not suggest using it to transfer all your files from the old computer. It would be much better to prep the drive for use on the Mac:
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
This disk format is unreadable on a PC without third-party software such as MediaFour's MacDrive.

Transfering files between devices

Similar Messages

Maybe you are looking for