Transfering minidv in LP MODE

Can someone tell me if you can transfer mini dv in LP mode using a panasonic dvx100a into final cut pro without any problems or does it just transfer SP

Does it play the mini DV tape recorded in LP mode just fine? I'm guessing this is what you're doing - capturing tapes that were recorded in LP on another camera?
If it plays back fine, it should probably capture fine too.
I had a problem capturing with DSR-11 and had to use the original camera that recorded the LP tapes. It played them back fine and captured as well. If it looks good on the Capture window of FCP, it should capture.
Good luck.

Similar Messages

Transfering files in ASCII mode using SFTP

Hi All,
We are using SFTP to transfer our files since we are using VPN. But we need a file to be transfered in ASCII mode from the remote system. We are using toad for that, but i heard that SFTP transfers file only in Binary mode by default. Is there any way to achieve it.?
Thanks
Narain

Hi Narain,
SFTP transfers files in Binary mode only as it transfers over SSH - so it is upto the sending/receiving client to manage the line endings.
In BPEL,a java embedding can be used to convert line endings and then the payload handed over to FTP adapter for SFTP.
Regards,
Shanmu.

Transfering MiniDV to PowerBook G4: Firewire Cable

What should I look for in a firewire cable when transfering MiniDV from a camcorder to my PowerBook using FCS? Any recommendations would be very helpful. Thanks!
Powerbook G4 1.67GHz Mac OS X (10.4.4) Final Cut Studio/2GB DDR SDRAM
Powerbook G4 1.67GHz Mac OS X (10.4.4) Final Cut Studio/2GB DDR SDRAM

The transfer from your camera to the computer is a digital transfer - not analog. So even with a bad cable, there is no 'degradation' of image. If the cable is bad, the transfer simply doesn't work.
For short runs, as long as there is a solid fit in the camera and computer receptacles, most cables from reputable manufacturers will be fine. If you are running 16' or even 32' cables - then the manufacturer is pretty important.
Having said all this, Granite Digital sells a line of cables that are well made, well shielded and very reliable. I know there are others.
good luck.
x

Transferring files via Target Mode

Hello,
I just got my Mac Pro and I'm trying to transfer some files and programs from my existing G4... I have heard about using the "Target Mode" to do this, but when I tried no luck. Here's what I attempted to do:
attmept #1. G4 is connected to my display. I booted the G4 holding down the "T" key. I see the firewire symbol on the screen, so I connected a firewire cable from the G4 to the Pro and turned on the Pro. Nothing happened. Should I have connected the display cable to the Pro too? I don't need 2 displays to do this action, right?
attempt #2. Mac Pro is connected to the display. I boot the Pro and follow instructions via "Migration Assistant". So I connected the firewire from the Pro to the G4 (while Pro is still running) and booted the G4 while holding down the "T" key and still nothing happens.
What am I doing wrong? Can anyone offer some assistance please? Thanks in advance.

Hi hscarr;
Transferring programs from a G4, which is PowerPC architecture, to a Mac Pro, which is Intel architecture, is a know method of creating problems.
It is highly recommend that instead all applications be freshly install on the Intel platform.
Once that is done that your data can be moved.
Allan

Transferring itunes from old desktop to new laptop

painstakingly ollowed instructions on how to use ipod mini as hard drive, but found out none of my music tranferred. i have access to my old itunes - can i transfer directly from desktop to laptop? thx.

Hi there,
As i remember it Apple's answer is not insane.
Music sync'd to an iPod using iTunes doesnt show up as files (they're 'invisible'). As I remember it is only files that you hand copy to the mounted hard disk that do show up.
If that's true then to see no music files after an iTunes sync is normal. Problem is the usual utilities wont allow you to transfer the 'invisible' music up onto your new PC.
1/ Make sure music is transferred in 'hard disk mode' and if it doesnt then show up then it isnt copied.
2/ Use one of the un-usual utilities which circumvent Apple's attempt to prevent copying of music from iPod to a computer. E.g. http://www.ilounge.com/index.php/articles/comments/copying-music-from-ipod-to-co mputer/

Setting File transfer mode in SFTP using JSch (jsch-20070302.jar)

Hi,
I use Jsch for downloading and uploading files via SFTP. I am a facing a problem in the file transfer mode. When I download or upload manually the files seems file, but when I use my code to download or upload there is some problem. Actally the file has to be transferred in ASCII mode, but the code transfers it in binary mode. Below is the code I am using
+import com.jcraft.jsch.*
Session session = null;
try {
populateProperties();
log("INFO","Download and Encrypt Program started",getDateTime());
JSch jsch = new JSch();
String host = tumbleweedURL;
String user = tUserid;
session = jsch.getSession(user, host, 22);
session.setUserInfo(new MyUserInfo());
session.setPassword(tPassword);
session.connect();
Channel channel = session.openChannel("sftp");
channel.connect();
ChannelSftp c = (ChannelSftp) channel;
c.cd("outbox");
c.get("8",outFolderPath);
}+
Please tell me how I change the transfer mode to ASCII for the above code

Vignesh_kumar wrote:
I am not sure where to put this question, I have tried a lot of things and I am not able to find a solution for this. Will you be able to guide me..A mailing list, or forum, or faq, or support address at JCraft, maybe?

Alternate modes in PPDS

Dear Friends,
i have created alternate sequence in ECC this is transferred to APO as modes. when planning in APO it takes standard sequence always for planning. now my requirement is if the load is already there for the standard sequence/mode the system has to automatically schedule to the alternate sequence. but now this can be done only manually which my client is not accepting. Pls let me know if there is anyway where we can overcome this problem.
Regards
vinay
Edited by: vinay on Jul 9, 2009 7:01 AM

transaction is /sapapo/cdpsc5, you can copy from optimisation profile sap001,
you can use at it is sap001 also.
after you open the optimisation proflie you can explore the functionality.
but i think you dont need to change anything expect optimisation horizon.
you can call this optimisation in last step of planning run.
if you further need any help please revert back.

6509E Fan tray 1 mode change failed

I have just installed a CEF720 8 port 10GE with DFC WS-X6708-10GE card in an existing 6509E Chassis and it shuts down due to inadequate cooling.
I have another 6509E Chassis with exactly the same setup and it works ok with that. Both are brand new.
The one transfers to High power mode and the other fails when trying to swap to restricted mode.
*Mar 5 13:55:38.527: %C6KENV-SP-4-FANHPMODE: Fan-tray 1 is operating in high power mode
*Mar 5 13:55:38.535: %C6KENV-SP-4-INSUFFCOOL: Module 9 cannot be adequately cooled
*Mar 5 13:56:38.787: %C6KENV-SP-3-FANMODEFAIL: Fan-tray 1 mode change failed
#sh env cooling
fan-tray 1:
fan-tray 1 type: WS-C6509-E-FAN
fan-tray 1 mode: Restricted-power
fan-tray 1 fan-fail: OK
chassis per slot cooling capacity: 70 cfm
ambient temperature: < 55C
module 1 cooling requirement: 30 cfm
module 2 cooling requirement: 30 cfm
module 3 cooling requirement: 30 cfm
module 5 cooling requirement: 35 cfm
module 8 cooling requirement: 70 cfm
module 9 cooling requirement: 84 cfm
environmental alarms:
no alarms
backplane:
operating clock count: 2
operating VTT count: 3
operating fan count: 1
fan-tray 1:
fan-tray 1 type: WS-C6509-E-FAN
fan-tray 1 mode: Restricted-power
fan-tray 1 fan-fail: OK
VTT 1:
VTT 1 OK: OK
VTT 1 outlet temperature: 0C
VTT 2:
VTT 2 OK: OK
VTT 2 outlet temperature: 0C
VTT 3:
VTT 3 OK: OK
VTT 3 outlet temperature: 0C
clock 1:
clock 1 OK: OK, clock 1 clock-inuse: in-use
clock 2:
clock 2 OK: OK, clock 2 clock-inuse: not-in-use
power-supply 1:
power-supply 1 fan-fail: OK
power-supply 1 power-input: AC high
power-supply 1 power-output-mode: high
power-supply 1 power-output-fail: OK
power-supply 2:
power-supply 2 fan-fail: OK
power-supply 2 power-input: AC high
power-supply 2 power-output-mode: high
power-supply 2 power-output-fail: OK
module 1:
module 1 power-output-fail: OK
module 1 outlet temperature: 27C
module 1 inlet temperature: 23C
module 1 device-1 temperature: 27C
module 1 device-2 temperature: 23C
module 1 VDB outlet temperature: 25C
module 1 VDB inlet temperature: 24C
module 1 VDB device-1 temperature: 25C
module 2:
module 2 power-output-fail: OK
module 2 outlet temperature: 26C
module 2 inlet temperature: 23C
module 2 device-1 temperature: 27C
module 2 device-2 temperature: 24C
module 2 VDB outlet temperature: 25C
module 2 VDB inlet temperature: 23C
module 2 VDB device-1 temperature: 25C
module 3:
module 3 power-output-fail: OK
module 3 outlet temperature: 27C
module 3 inlet temperature: 23C
module 3 device-1 temperature: 28C
module 3 device-2 temperature: 23C
module 3 VDB outlet temperature: 23C
module 3 VDB inlet temperature: 22C
module 3 VDB device-1 temperature: 25C
module 5:
module 5 power-output-fail: OK
module 5 outlet temperature: 32C
module 5 inlet temperature: 21C
module 5 device-1 temperature: 26C
module 5 device-2 temperature: 29C
module 5 asic-1 temperature: 51C
module 5 asic-3 temperature: 35C
module 5 asic-4 temperature: 46C
module 5 RP outlet temperature: 25C
module 5 RP inlet temperature: 26C
module 5 EARL outlet temperature: 28C
module 5 EARL inlet temperature: 23C
module 8:
module 8 power-output-fail: OK
module 8 outlet temperature: 23C
module 8 inlet temperature: 22C
module 8 device-1 temperature: 20C
module 8 device-2 temperature: 24C
chassis connector rating: 1302.00 Watts (31.00 Amps @ 42V)
chassis auxiliary connector rating: 2016.00 Watts (48.00 Amps @ 42V)
module 1
module 1 connector rating: 1260.00 Watts (30.00 Amps @ 42V)
module 1 vdb connector rating: 850.08 Watts (20.24 Amps @ 42V)
module 1 power consumption: 132.72 Watts ( 3.16 Amps @ 42V)
module 2
module 2 connector rating: 1260.00 Watts (30.00 Amps @ 42V)
module 2 vdb connector rating: 850.08 Watts (20.24 Amps @ 42V)
module 2 power consumption: 132.72 Watts ( 3.16 Amps @ 42V)
module 3
module 3 connector rating: 1260.00 Watts (30.00 Amps @ 42V)
module 3 vdb connector rating: 850.08 Watts (20.24 Amps @ 42V)
module 3 power consumption: 132.72 Watts ( 3.16 Amps @ 42V)
module 5
module 5 connector rating: 1260.00 Watts (30.00 Amps @ 42V)
module 5 power consumption: 338.10 Watts ( 8.05 Amps @ 42V)
module 8
module 8 connector rating: 2016.00 Watts (48.00 Amps @ 42V)
module 8 power consumption: 125.16 Watts ( 2.98 Amps @ 42V)
module 9
module 9 connector rating: 2016.00 Watts (48.00 Amps @ 42V)
module 9 power consumption: 444.36 Watts (10.58 Amps @ 42V)
chassis per slot cooling capacity: 70 cfm
ambient temperature: < 55C
module 1 cooling requirement: 30 cfm
module 2 cooling requirement: 30 cfm
module 3 cooling requirement: 30 cfm
module 5 cooling requirement: 35 cfm
module 8 cooling requirement: 70 cfm
module 9 cooling requirement: 84 cfm
*Mar 5 13:55:38.527: %C6KENV-SP-4-FANHPMODE: Fan-tray 1 is operating in high power mode
*Mar 5 13:55:38.535: %C6KENV-SP-4-INSUFFCOOL: Module 9 cannot be adequately cooled
*Mar 5 13:56:38.787: %C6KENV-SP-3-FANMODEFAIL: Fan-tray 1 mode change failed
#sh mod
Mod Ports Card Type Model Serial No.
1 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-45AF SAL1335XN4J
2 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-45AF SAL1336Y10M
3 48 SFM-capable 48 port 10/100/1000mb RJ45 WS-X6548-GE-45AF SAL1539QUPY
5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1532LPPY
8 24 CEF720 24 port 1000mb SFP WS-X6724-SFP SAL1227WDGA
9 8 CEF720 8 port 10GE with DFC WS-X6708-10GE SAL1746G73Z
Mod MAC addresses Hw Fw Sw Status
1 0027.0d00.2910 to 0027.0d00.293f 12.5 7.2(1) 12.2(33)SXJ Ok
2 0027.0d00.2880 to 0027.0d00.28af 12.5 7.2(1) 12.2(33)SXJ Ok
3 44d3.ca8b.bed0 to 44d3.ca8b.beff 12.7 7.2(1) 12.2(33)SXJ Ok
5 68ef.bd83.524c to 68ef.bd83.5253 4.0 8.5(4) 12.2(33)SXJ Ok
8 0021.d88c.1e10 to 0021.d88c.1e27 3.2 12.2(18r)S1 12.2(33)SXJ Ok
9 c067.afc4.09b8 to c067.afc4.09bf 3.6 Unknown Unknown PwrDown
Mod Sub-Module Model Serial Hw Status
1 IEEE Voice Daughter Card WS-F6K-48-AF SAL1336Y0SH 2.4 Ok
2 IEEE Voice Daughter Card WS-F6K-48-AF SAL1336Y01P 2.4 Ok
3 IEEE Voice Daughter Card WS-F6K-48-AF SAL1538QHUV 2.5 Ok
5 Policy Feature Card 3 VS-F6K-PFC3C SAL1531L4CR 1.1 Ok
5 MSFC3 Daughterboard VS-F6K-MSFC3 SAL1531LH76 5.1 Ok
8 Centralized Forwarding Card WS-F6700-CFC SAL1227W50M 4.1 Ok
9 Distributed Forwarding Card WS-F6700-DFC3C SAL1744FFSW 1.6 PwrDown
Mod Online Diag Status
1 Pass
2 Pass
3 Pass
5 Pass
8 Pass

Hi see the below information:
About the Fan Tray Mode: This high power mode may change to restricted power mode depending upon the environment temperature, the fan may be working at High or Restricted mode depending on the cooling needed at the moment.
Restricted Power mode: This is a default mode for a fan-tray operation. This mode ensures that there is an adequate amount of cooling provided to the chassis to keep its temperature in control.
High Power mode: This is another mode which is used for future line cards if there an increase in temperature due to addition of modules. In our case, this mode only gets in use when there is WS-X6708-10GE module inserted. Logs are getting displayed as new module is causing rise in chassis temperature and fan-tray has to accommodate more cooling thereby changing its operating mode.
The WS-X6708-10GE requires 84 cfm. Installing a second fan module in the chassis should bring the chassis cooling capacity up to 84 cfm per line card. WS-X6708-10GE is supported in non-E Series chassis at operating temperature up to 40 C only.
Hope this helps.

How to install iLife on an iBook without DVD drive

Some time ago I bought iLife 8 only to find it was on a single DVD which I could not use on my twin-USB iBook with only a CD drive. Now a friend has suggested that the DVD could perhaps be copied to 6 Cds and loaded that way. Toast has a spanning facility to spread a big file over multiple disks. Or could my iBook be hooked to a big Mac with a DVD drive, and the program transferred by Target Disk Mode. Does anyone know if either of these techniques would work?

Of the two, target mode would be far more efficient (and less risky -- in terms of software data corruption). I have in the past installed OS X on a machine with a poor DVD drive, so iLife should be no problem.

Wire transfer Incoming payment

Hi Gurus,
i got a scenario to import wire transfer file ( one receives from bank) to sap. usually we have transaction to import the lockbox file (T-code FBL2) in to sap and do posting. Similarly, whether is there any t-code or program for importing wire transfer file and do incoming payments in sap.
Thanks in advance.

Hi
Think the below would be helpful:
Wire Transfer - Refers to a same-day transfer of funds from an account at one bank to an account at another bank, initiated over the Fedwire system. The Fed guarantees to pass value as of the date of the Fedwire transfer is initiated provided the transfer meets all required criteria. Fedwire is a part of the Federal Reserve System Communication Systems.
ACH Transfer - Clearinghouse associations in many major cities have developed electronic methods of passing payments among members and other financial institutions in the region, and of exchanging payments among the ACHs themselves. ACH transfers may be either credit transfers (sending funds out) or debit transfers (pulling funds in). Either the payee or the payor may initiate them.
Differences between Wire and ACH
Wire Transfer is geared to a single transfer, while ACH Transfer is geared to handling multiple transfers in a batch mode.
Wire Transfer is geared to same-day settlement, while ACH Transfer is geared to future-date settlement.
Wire Transfer is expensive because of their customized one-at-a time nature, while ACH Transfer is inexpensive because of their structured data format and high-volume batch nature.
Regards
Aravind
Assign points if useful

Can't open Web Archive

Thanks for reading. I have a number of web archives saved and understood them to save whatever was shown, notwithstanding future changes to the page. Am I correct in my understanding?
Trying to open some (not all) of these pages, I get "There was one opening error... choose Activity from the Window menu." The pages will not open.
Choosing Activity shows-
"file:///Users/martin_bell/Documents/Documents/Finances/Sandys%20Tax/Sandy's%20 return%202006:2007.webarchive 1 of 2 items (1 error)".
These were saved on a previous iMac and transfered using target disk mode. Any ideas?
Thanks.

Hi Martin
safari & webarchives is a little err, less than ideal... although most of the images/items are stored in the archive - they don't always seem to get displayed by safari if they're no longer on the web - hmmm.
web archive folderizer extracts all stored items from the webarchive into folders, but doesn't produce a nice, easy to click icon that displays it all in a browser - however, it might let you find the items that don't show up.

FTP transfer problem

Hi,
I've created a code that transfer files from a Robot Controller to a PC.
My code is working, I can see all the files in my computer and I don't have any error from LabVIEW, but the size of the files are not exactly the same.
We decided to compare the files (binary comparison) with UltraCompare and some bytes are not the same, which cause us big trouble.
I'm using LabVIEW 2010 SP1.
You can see in attachment the result from the UltraCompare Software, also the 2 files transfered with CoreFTP and with my LabVIEW code.
Any ideas why some bytes are not exactly the same?
Thank you
Stephanie
Attachments:
FTP Problem.zip ‏110 KB

The FTP VIs are part of the internet toolkit I believe.
The files you retrieved with CoreFTP correctly match the ones you uploaded? Also are all the differences single bits like in the pictures?
There's a file error line from the retrieve VI - do you ever see anything of note on it?
If you do all the transfers without using binary mode do you have the same issue?
Another, maybe better, option would be to use the retrieve multiple VI. This would let you wire the cluster you build in the second to last for loop straight to the VI instead of having to use the last for loop.
http://zone.ni.com/reference/en-XX/help/370014E-01/internetftp/ftp_retrieve_multiple/
Also I didn't see the close FTP session VI anywhere. You might make sure you're using it.

How convert to jpg picture into bmp ?

Hi experts,
I am trying to convert my jpg picture into bmp. for this i write one report but showing some
TRANSFER WA_MIME1 TO DSN1.
HERE IS MY FULL CODE PLZ HELP ME.
REPORT ZSE78_7.
DATA: blob TYPE w3mimetabtype,
 blob_size TYPE w3param-cont_len,
 blob_type TYPE w3param-cont_type .
DATA:
 p_color_scheme TYPE char20 ,
 p_labels_groupid TYPE igs_label_tab,
 p_labels_category TYPE igs_label_tab ,
 p_data TYPE igs_data_tab,
 p_charttype TYPE char20,
 p_legend TYPE char20,
 l_igs_chart TYPE REF TO cl_igs_chart ,
 l_igs_chart_engine TYPE REF TO cl_igs_chart_engine,
 i_igs_image_converter TYPE REF TO cl_igs_image_converter,
 mime TYPE w3mimetabtype,
 html TYPE w3htmltabtype,
 html_line TYPE w3html,
 l_msg_text(72) TYPE c,
 l_url TYPE w3url,
 l_content_length TYPE i,
 l_content_type TYPE w3param-cont_type,
 l_content_subtype TYPE w3param-cont_type.
CALL FUNCTION 'GUI_UPLOAD'
 EXPORTING
 filename = 'e:\katoch.jpg'
 filetype = 'BIN'
* HAS_FIELD_SEPARATOR = ' '
* HEADER_LENGTH = 0
* READ_BY_LINE = 'X'
* DAT_MODE = ' '
* CODEPAGE = ' '
* IGNORE_CERR = ABAP_TRUE
* REPLACEMENT = '#'
* CHECK_BOM = ' '
IMPORTING
 filelength = l_content_length
* HEADER =
 TABLES
 data_tab = mime
EXCEPTIONS
 file_open_error = 1
 file_read_error = 2
 no_batch = 3
 gui_refuse_filetransfer = 4
 invalid_type = 5
 no_authority = 6
 unknown_error = 7
 bad_data_format = 8
 header_not_allowed = 9
 separator_not_allowed = 10
 header_too_long = 11
 unknown_dp_error = 12
 access_denied = 13
 dp_out_of_memory = 14
 disk_full = 15
 dp_timeout = 16
 OTHERS = 17
IF sy-subrc <> 0.
 MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
 WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
CREATE OBJECT i_igs_image_converter .
i_igs_image_converter->input = 'image/jpeg'.
i_igs_image_converter->output = 'image/x-ms-bmp'.
i_igs_image_converter->width = '100'.
i_igs_image_converter->height = '100'.
CALL METHOD i_igs_image_converter->set_image
 EXPORTING
 blob = mime
 blob_size = l_content_length.
CALL METHOD i_igs_image_converter->execute
 EXCEPTIONS
 communication_error = 1
 internal_error = 2
 external_error = 3
 OTHERS = 4.
IF sy-subrc = 0.
 CALL METHOD i_igs_image_converter->get_image
 IMPORTING
 blob = blob
 blob_size = blob_size
 blob_type = blob_type.
 DATA dsn1(20) TYPE c VALUE 'E:\test.bmp'.
DATA wa_mime1 TYPE w3mime.
*DATA wa_mime1 TYPE w3mimetabtype.
 OPEN DATASET dsn1 FOR OUTPUT IN BINARY MODE.
 LOOP AT blob INTO wa_mime1.
 TRANSFER wa_mime1 TO dsn1.
 CLEAR wa_mime1.
 ENDLOOP.
MESSAGE ' successfull' TYPE 'I'.
 CLOSE DATASET dsn1.
ELSE.
 DATA: num TYPE i, message TYPE string.
 CALL METHOD i_igs_image_converter->get_error
 IMPORTING
 number = num
 MESSAGE = message.
MESSAGE 'not successfull' TYPE 'I'.
ENDIF.

HI
i already converted it in binary form but when i transferring it to binary mode it generate error.
the code is like this.
LOOP AT blob INTO wa_mime1.
 TRANSFER wa_mime1 TO dsn1.
 CLEAR wa_mime1.
 ENDLOOP.
 CLOSE DATASET dsn1.

Conversion jpeg image into bmp

Hi experts,
I am trying to convert my jpg picture into bmp. for this i write one report but it showing some transferring error to binary mode
here is my code
*& Report ZSE78_8
REPORT ZSE78_8.
DATA: blob TYPE w3mimetabtype,
 blob_size TYPE w3param-cont_len,
 blob_type TYPE w3param-cont_type .
DATA:
 p_color_scheme TYPE char20 ,
 p_labels_groupid TYPE igs_label_tab,
 p_labels_category TYPE igs_label_tab ,
 p_data TYPE igs_data_tab,
 p_charttype TYPE char20,
 p_legend TYPE char20,
 l_igs_chart TYPE REF TO cl_igs_chart ,
 l_igs_chart_engine TYPE REF TO cl_igs_chart_engine,
 i_igs_image_converter TYPE REF TO CL_IGS_IMAGE_CONVERTER,
 mime TYPE w3mimetabtype,
 html TYPE w3htmltabtype,
 html_line TYPE w3html,
 l_msg_text(72) TYPE c,
 l_url TYPE w3url,
 l_content_length TYPE i,
 l_content_type TYPE w3param-cont_type,
 l_content_subtype TYPE w3param-cont_type.
CALL FUNCTION 'GUI_UPLOAD'
 EXPORTING
 filename = 'E:\KATOCH.gif'
 filetype = 'BIN'
 HAS_FIELD_SEPARATOR = ' '
 HEADER_LENGTH = 0
 READ_BY_LINE = 'X'
 DAT_MODE = ' '
 CODEPAGE = ' '
* IGNORE_CERR = 'ABAP_TRUE'
 REPLACEMENT = '#'
 CHECK_BOM = ' '
IMPORTING
 filelength = l_content_length
* HEADER =
 TABLES
 data_tab = mime
EXCEPTIONS
 file_open_error = 1
 file_read_error = 2
 no_batch = 3
 gui_refuse_filetransfer = 4
 invalid_type = 5
 no_authority = 6
 unknown_error = 7
 bad_data_format = 8
 header_not_allowed = 9
 separator_not_allowed = 10
 header_too_long = 11
 unknown_dp_error = 12
 access_denied = 13
 dp_out_of_memory = 14
 disk_full = 15
 dp_timeout = 16
 OTHERS = 17
IF sy-subrc <> 0.
 MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
 WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
CREATE OBJECT i_igs_image_converter .
i_igs_image_converter->input = 'image/gif'.
*i_igs_image_converter->output = 'image/x-ms-bmp'.
i_igs_image_converter->output = 'image/gif'.
i_igs_image_converter->width = '100'.
i_igs_image_converter->height = '100'.
CALL METHOD i_igs_image_converter->set_image
 EXPORTING
 blob = mime
 blob_size = l_content_length.
CALL METHOD i_igs_image_converter->execute
 EXCEPTIONS
 communication_error = 1
 internal_error = 2
 external_error = 3
 OTHERS = 4.
IF sy-subrc = 0.
 CALL METHOD i_igs_image_converter->get_image
 IMPORTING
 blob = blob
 blob_size = blob_size
 blob_type = blob_type.
 DATA dsn1(20) TYPE c VALUE 'E:\katoch1.bmp'.
 DATA wa_mime1 TYPE w3mime.
*DATA wa_mime1 TYPE w3mimetabtype.
 OPEN DATASET dsn1 FOR OUTPUT IN BINARY MODE .
 LOOP AT blob INTO wa_mime1.
 TRANSFER wa_mime1 TO dsn1.
 CLEAR wa_mime1.
 ENDLOOP.
 CLOSE DATASET dsn1.
ELSE.
 DATA: num TYPE i, message TYPE string.
 CALL METHOD i_igs_image_converter->get_error
 IMPORTING
 number = num
 MESSAGE = message.
ENDIF.

Hi,
To convert an Image to bytes you can use the Image.getRGB() method.
http://java.sun.com/javame/reference/apis/jsr118/javax/microedition/lcdui/Image.html#getRGB(int[], int, int, int, int, int, int)
-Henrik

Call new URL in same Browser

Hi @ all,
I try to call another WD4A-Application with:
lr_window = lr_window_manager->create_external_window( url = lv_url ).
The system create a new browser window, but I want to start it in the same browser window (or close the parent window).
Have somebody an idea to solve this?
thanks
Jürgen

>can you clarifiy please how it comes to the general statement
I don't have any details I can share. If development makes such a statement, they must have encountered some incompatibilites that cause they not to support this technology within the Portal.
Here is some additional detail from the 7.02 online help:
http://help.sap.com/saphelp_nw70ehp2/helpdata/en/43/6b972329d23d33e10000000a11466f/frameset.htm
For every interface view, you can flag exactly one inbound plug as a resume plug. When navigating in the portal, the existence of a resume plug results in the following behavior: If the Portal Navigation recognizes such a plug in the running application, the latter is not exited when navigating away but is instead transferred to a suspend mode. The session ID and contents of the context are retained and a new application is started. If a user then goes back to the original application via the navigation menu of the portal, it can be processed in exactly the same state in which it was left. Note the following:
If an application features a resume plug, the corresponding session is retained when navigating away in the portal. However, in many cases it may be sensible or even absolutely necessary to close the application completely. In such cases, you must not implement a resume plug for the interface view.
While your applications are running within a portal, the portal navigation takes care of the suspend step without you having to implement it at design time. The mere existence of a resume plug ensures that an application is only interrupted and not exited in the case of a portal navigation. However, this does not take place if the application is not running in the portal and can thus not make use of the portal navigation mechanism.
If an outbound plug is flagged as a suspend flag in a Web Dynpro ABAP application, this can lead to errors when the application is executed in the portal. If you are not completely sure that your application is executed solely outside a portal, you should avoid the use of suspend plugs.

Transfering minidv in LP MODE

Similar Messages

Maybe you are looking for