Transferring Hi-8 video into imovie

I am very new to this. The reason I got the Mac was to edit old home videos. This has been a nightmare so far.
But , now I have found that there are two products out there that ( I hear ) will do the job real easy.
The two products are DATAVIDEO DAC200 or the CANOPUS ADVC55.
What I want to do is to transfer the Hi-8 tape onto the mac. Be able to edit and make a new DVD from that one tape and also DVD's from a compilation of Hi-8 tapes.
Basically, put all my tapes onto imovie to have the capability to create whatever kind of DVD that I want using bits and pieces of all the tapes.
Help!!
What I was doing before I found these products was: copying the tape onto a DVD using a DVD recorder. Then using Handbrake on the mac to convert to mpeg4. Then transfer to imovie. But it was taking about 10 hours for 1.5gb. And after all that, I could not see any of the clips to edit. I could watch the movie ...that was it.
Please, any help at all would be greatly appreciated.
Thanks

I borrowed a friends Digital 8 camcorder and put my old analog Hi8 into hers and connected to my iMac via Firewire (it works as a converter), however there was a bug in iMovie 08 that it didn't recognize it, but I read that iMovie 06 would, (downloadable free if you have 08). So I transferred it in through 06 and pulled it into 08. Cumbersome, but works. The link below discusses it.
http://forum.videohelp.com/topic341622.html
However, I decided to wait for Apple to fix the bug before I spent the time to transfer 50+ tapes, which they apparently did in January, according to this post:
http://forums.appleinsider.com/showthread.php?t=83125
I haven't tried it again, but they say it works now, if not you can do iMovie 06. You just need to borrow somebody's Digital 8 for the converter. I haven't tried using my old Hi8 as the player and use my miniDV connected in between as the digital converter, but I've heard that works.
I just figured out how to send it direct to an external hard drive since 1 tape takes up 25G. I've bought several 500G for $100, however, I just noticed that they only have USB, and a Firewire one would be faster. I created a project in iMovie 08 using video from the external and it did not seem to be a sluggish interface. Now to figure out editing, then send it to iDVD... they make it sound so easy! I've yet to make my first movie!

Similar Messages

  • Transferring mini dvd video into imovie in Chronological order

    Transferring mini dvd video into imovie in Chronological order 

    Transferring mini dvd video into imovie in Chronological order.
    but don't ?
    MacBook Pro
    Mac OS X
    version 10.7.5
    Imovie ' 11
    version 9.0.8
    Hitachi camcorder
    Message was edited by: D Lamsal

  • Trouble importing video into iMovie from External HD

    I have video from my Panasonic Full HD camera.  I have already transferred the video off the camera and onto an external hard drive.  When I try to import the video into iMovie those files are grayed out.  Does anyone have any idea how to make this work?
    It is all my video of my son's first year since birth!

    It is very important that when you transferred the video off the camera, you kept all files and folders from the camera. If you did, you can open iMovie and use FILE/IMPORT FROM CAMERA ARCHIVE and navigate to the folder that contains the contents that you removed from the camera.
    In the future, open iMovie and use FILE/IMPORT FROM CAMERA. This will bring up an import screen. There you can click a button that says Create Camera Archive. This will automatically get you all the files you need off the camera, and it gives you a good backup.
    You can also import directly into iMovie from this screen.
    If you did not preserve the contents of the camera - for example, you just copied the .mts files, but did not copy the rest of the files and folders, you will need a third party app to convert the .mts files so that iMovie can read them. Two apps that people use for this are ClipWrap and Voltaic HD. They are pricey, but if you did not copy the full camera contents, this may be your best bet.

  • I have been trying to import VHS video into iMovie via a Hollywood Dazzle bridge.  Did not have trouble until I upgraded to mavericks.  I have a mac book pro, 10.9.1, iMovie 10.0.2.  Says it is recording, but when I go to check, it says the file is empty.

    I have been trying import VHS video into iMovie via a Hollywood Dazzle bridge.  I have been successful doing this in the past, but now it is not working.  I have a mac book pro, 10.9.1, (mavericks), iMovie 10.0.2.  Everything in iMovie looks like it is working.  It reads "recording" in the upper left hand corner of the pane while the video is playing.  When I stop the process to check on my clip it says that the file is empty.  The only thing that has changed since I did it successfully is that I upgraded to mavericks from whatever I had previously.  My system is about one year old.  Any suggestions?

    Hey, Clinton,
         Thanks for your help!  I was able to go to iMovie 9.0.9 and import video.  I was still curious as to why it didn't work in version 10.0.2, so I contacted Apple tech support.  They were't sure at first as to why it wouldn't work, so they had me delete iMovie 10.0.2 and then re-install it just to see if something had gone wrong when it upgraded.  That didn't change anything.  In the end, they determined that 10.0.2 doesn't support the Hollywood Dazzle DV bridge.  But I have a workaround path from them that I will share so that it's possible to import to 9.0.9, then move it to 10.0.2. 
         1.  Open iMovie 9 (finder/applications/iMovie 9.0.9
         2.  Import from Dazzle Bridge to iMovie 9, note which event you are importing the clips into
         3.  Close iMovie 9
         4.  Open iMovie 10 (probably in the dock)
         5.  File/Import Media...navigate to home(this was my name, on the left side of iMovie, under Favorites)/Movies/iMovie events.  Find the event folder that contains your Dazzle clips (tip-try sorting by date modified to look at recent events.) 
         6.  Select the clips and import.  Click the blue "Import Selected" button on the bottom right.
    You may get a message that some files cannot be imported.  Click continue import.  It's a little glitchy.  It imports your clip, and also makes a copy of it, too.  On the copy, the audio is normal, but the video is choppy.  In any case, you would delete the copy, anyway.
    Hope this additional information helps somebody else.  Thanks again, Clinton for helping me!

  • I imported an hour of video into iMovie HD and cut it down to a 33 sec clip, and emptied the trash.  When I save the project, the file size is 20Gb.  How can I save just the 33 sec clip?

    I imported an hour of video into iMovie HD and cut it down to a 33 sec clip, and emptied the trash.  When I save the project, the file size is 20Gb.  How can I save just the 33 sec clip?

    Non-destructive editing is an important feature of iMovie HD 6.
    iMovie preserves the entire copy of every clip you place into your movie in case you change your mind at a later stage.
    So, if you have cut out one minute from a 45 minute clip, iMovie will have stored two complete copies of that clip. This is why is helps to set import as 3-5 minute clips rather than one huge chunk. As DV runs at 13GB per hour your project files can get very big.
    One workaround is to complete the editing of a section of the movie, then export that to Quicktime: highlight the clip/s, choose Share-Quicktime, turn on Share selected clips only, and choose Full Quality from the pop-ip menu.
    Once you have saved the stand-alone clip to your hard drive, you can re-import it into your project using the File/Import command, and delete the original long clip/s from the project.

  • FireWire is the only way to import Canon HV20 Camcorder videos into iMovie?

    As a followup to my last post a moment ago tonight 1/30/08:
    Is it true that I need a FireWire cable to import Canon HV20 Camcorder videos into iMovie?
    If so, the Apple salesperson is wrong.
    He told me last Monday that purchasing the new iLife 2008 (that contains iMovie 2008) would allow me to use my current USB cable.
    Given I see NO FireWire port on my new MacBook Pro (bought in 8/2006), I don't see a solution.
    Note the camera, an HD camcorder (the Canon HV20) did NOT come with a FireWire cable; it only came with a USB male plug on one side of the cable and the other is a small square-like male plug that connects to a female port on the Canon HV20.
    Solution?
    Thanks for any suggestions, Daniel

    The USB cable is for importing still photographs. Not video.
    The firewire 400 cable you need is one that goes from the 6 pin full size male connector to the small 4 pin form used for DV.
    The cable plugs into the camera in a socket behind a plastic flap near the eyepiece. Its marked HDV/DV. The other end plugs into the MBP on the right-hand side. 4th from the back.

  • Getting Analog Video into iMovie

    Greetings,
    OK, so I have successfully imported digital video into iMovie on several occasions with my "newer" video camera (a SONY DCR-TRV80).
    Problem is, I have and older camera (a Canon ES800A) that uses 8mm tape. I've been wanting to get rid of the camera (a nice one for it's time) but, I have about 6 tapes worth of video that I'd like to at least permanently archive.
    I suspect there is some hardware device out there that will allow me do to this - can anyone tell me would I need to be shopping for? (hoping it's not prohibitively expensive!)
    Any help would be appreciated!
    Next up? - a camcorder with a hard disk!
    Thanks,
    Jim

    Hi : I have a related problem maybe you could help me with....I've got about 6 Beta tapes [ remember them ? ] that I'd like to transfer to DVD while there still viewable. About 4 hours of tape on each....
    I have an Optura 20 DV [Canon] and a Beta tape machine. The optura 20 manual says you should be able to run the RCA plugs out of the Beta unit into the AV jack on the Optura, then FW out into I - Movie. OR you can record onto a DV tape, then into IMovie. I've had no luck with either method. No Beta material shows on the DV monitor no matter what I do. It does play into a standard T.V from Beta, so I know the tape AND the Beta machine are working.
    Do I need something like that Canopus Converter ? ....don't know if that' s the exact name .
    Any suggestions appreciated...Thanks
    Braden

  • Imported video into iMovie but has no audio

    Imported video into IMovie has the video but no audio. I did recently upgrade to OS lion and earlier video imports from snow leopard is fine

    I too have this problem, I cannot get any audio in my imported movies, this was not a problem two weeks ago, can anyone help me?

  • Embedding video into imovie

    Can anyone tell me if imove embeds video into imovie project, or does is always need to find the video file to play it?
    thanks

    fryedmeb,
    I'm not sure if I completely follow your question, but I'll take a stab at it.
    What appears as a single iMovie project file is really a package containing all the necessary media for the project. Video clips, audio clips etc.
    It also contains a reference file with instructions on how all the pieces get put together to form the project.
    But, at the iMovie project stage, all the media are discrete pieces. "Unembeded" so to speak.
    Once you output (Share) your iMoive to, say, a full quality DV QuickTIme file, the movie is then rendered as one self contained file.
    Matt

  • Video Converters to get Sony Video into iMovie

    I am new to the video side of the world and need some advice. I am trying to import videos into iMovie. I am trying to import video from a Sony Cam, a DVD tht I made myself but mow would like to edit and my Flip Video. Additionally I will import video from a friends Nikon. Apple "suggested" handbrake, streamclip and toast. I see there a number of them on the app store. Any advice is greatly appreciated.
    Zapple

    Handbrake will be useful for converting the DVD back to a format that iMovie can edit. MPEG Streamclip requires some extra software still sold by Apple caleld the MPEG-2 QuickTime Playback component, download the beta of Streamclip and follow their directions for installing it will get the MPEG-2 component installed correctly. This will then let you open the DVD directly in Streamclip and get pieces out of it or just convert the whole disk to Apple Intermediate Codec. As for Sony and Flip video, don't know specifically which camera you have and what formats they record in, but there's likely a way to convert most of them into Apple Intermediate Codec which is the native editing/playback format that iMovie uses.

  • Bringing Videos into iMovie from DVDs

    I am a dance teacher and I have several dance teach DVDs. I created most of these from a VHS to DVD machine. They do work on standard DVDs and on the Mac.
    But, after spending the day reading through the iMovie 11 instructions, I have yet to find any explanation that would help me capture any of this video into iMovie 11.
    please send response to [email protected] I am not at all sure where this response goes and it seems to be going to my work email but I have retired.
    Jim

    Use MPEG Streamclip and Apple's MPEG-2 playback component to convert the VOB files on the DVD to DV. Click here for more information.
    (56930)

  • How can I import video into iMovie from a DVD?

    How can I import video into iMovie from a DVD?
    Thanks,
    Doug Davis

    You can do this with a free app called MPEG Streamclip and a $20 quicktime component from Apple.
    See detailed instructions here.
    https://discussions.apple.com/docs/DOC-3951

  • DI imported an mpeg4 video into iMovie 10.0.5 and the Precision Editor is grayed out and I can't edit.  Why??

    I imported an mpeg34 video into iMovie 10.0.5 and I am unable to edit it.  Precision Editor and Clip Trimmer are grayed out.  Any idea why this is happening?

    Did you get any joy with answering this?
    My first thought was that maybe when you imported you chose to leave the files  in place rather than copy then to the iMovie library..but I can't see where that option is now.
    I too have created a short movie from load f clips..but can't export or share either..the 'Share 'menu is empty..you go to it and no sub menu appears.

  • NO SOUND WHEN MOVING VIDEOS INTO iMOVIE!! something about Mpeg muxed?!?!

    I recorded my videos with my sony cybershot camera - no problems. I can rip them onto my Macbook Pro and watch them in quicktime and hear the sound just fine - no problems. But, when I pull the videos into iMovie HD to edit and try to watch the play back, I see video but no sound!! I looked in the help tab and it said that if my videos are Mpeg 1 "muxed" (or something like that) then I won't be able to hear any sound. Well how do I convert my videos to something that will allow me to hear the sound when I'm editing them in iMovie HD???
    Any help would be greatly appreciated!!!!!!!
    Thanks!
    Macbook Pro   Mac OS X (10.4.8)  

    Welcome to discussions, designerman.
    iMovie can't import MPEG1 or MPEG 2 files, and that's waht you are trying to do.
    Read this:
    Can not hear audio in iMovie when I import an MPEG clip
    http://www.danslagle.com/mac/iMovie/tips_tricks/6030.shtml
    :)Sue

  • When i import a video into iMovie the quality gets very ******,but when its not in iMovie it looks awesome

    when i import a video into iMovie the quality gets very ******,but when its not in iMovie it looks awesome, please help

    Exact same problem

Maybe you are looking for

  • Notification mail not send

    Hi All, I have an issue in PR workflow.A notification mail is send to user to approve a PR,but the user says that he did not receive that notification mail.He manually goes to transaction & approve the PR & workflow gets completed. Please let me know

  • How to make some fields mandatory for a custom screen we have added

    Hi All, Please let me know how can I make some fields mandatory through coding in PBO for only some fields of a screen. Say if I have 4 fields in my screen(module pool not selection screen) i want to make mandatory 2 fields based on some conditions h

  • Adobe are not that stupid with this 4.2 'update'...

    Well here it is: the eagerly awaited 4.2 update.  I updated today with much excitement.  Alas, the two main areas which i was hoping this update would fix, unfortunately, are not there.  I am talking about 1. The firewire out to external Monitor prev

  • Printing the Gantt Chart

    Hi, Does anyone know how I can select some Legends and print them within the Gantt Chart, preferrably at the bottom.  I stumbled unto the minutes of meeting of the "Project System Special Interest Group(PS-SIG)", in which this issue was raised to SAP

  • How to make this into star schema

    Hi experts I have 4 tables that I would like to turn into a star schema. table1(fact) has a N:1 to table2(dim) table2(dim) also has a 1:1 to table3(dim) and 1:1 to table4(dim) Is it possible to model this into a star schema where table1 (fact) has a