Translation from SF300-24P to 3650ios
I received a config from my vendor that they usualy put on a SF300 for their managed voice. Looks like you configure general ports and PVID's to allow two vlans on one port. Is this the same as switchport voice vlan <vlanid> ?
Also in the configuration I see the following
voice vlan id 20
voice vlan state disabled
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
This config won't work on my 3550 and 3560 switches. It seems this is some auto vlan config, how would this translate on a 3550 or a 3560? or is it needed at all?
Hi Devin. The OUI table is not needed. That is just an alternate method to implement voice VLAN if you chose not to use SX300 macro.
General port is a 802.1q trunk, it's not relevant to priority tagging. Priority tagging is based off a tag VLAN packet to accept the 4 bit VPT header to prioritize traffic. Port mode has no effect on this so long as it's a tagged packet.
-Tom
Please mark answered for helpful posts
http://blogs.cisco.com/smallbusiness/
Similar Messages
-
SF300-24p Q-in-Q - Changing from vlan 4095
I have a Cisco SF300-24P deployed at a customer prem running only a couple VLAN's - 1 customer related and 1 for management. Recently the customer inquired about changing his connection to Q-in-Q. I have changed the interface type to customer but then it selects vlan 4095 as the vlan associated to that port. How do I change that vlan or by default is that the only vlan I can use? Currently the customer is using vlan 904 and would like to continue to use that vlan in the Q-in-Q config.
Hi Christopher, I didn't run in to this problem at all. Please reference the 2 screen shots below. 4095 is a reserved PVID when a native vlan is not associated to the port.
-Tom
Please rate helpful posts -
Hello,
I've installed and configured 2 SF300-24P switches on Layer 3 mode in my company.
Since I've made this installation, I accounter some problems of stability in my LAN communication.
Here is the running config of the 2 switches:
First Switch
SW-WIFI#show running-config
config-file-header
SW-WIFI
v1.2.9.44 / R750_NIK_1_2_584_002
CLI v1.0
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
no cdp run
no spanning-tree
vlan database
vlan 2
exit
voice vlan state disabled
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
ip dhcp relay address 172.16.0.2
ip dhcp relay enable
ip dhcp information option
bonjour interface range vlan 1
hostname SW-WIFI
username cisco password encrypted 18c7e97c305303ec56fbb3105666d85721208731 privilege 15
ip ssh server
snmp-server server
clock timezone " " 0 minutes 0
ip telnet server
interface vlan 1
ip address 172.16.0.249 255.255.0.0
no ip address dhcp
interface vlan 2
name POSTES
ip address 192.168.1.245 255.255.255.0
ip dhcp relay enable
interface fastethernet1
ip dhcp relay enable
switchport trunk native vlan 2
interface fastethernet2
switchport trunk allowed vlan add 2
interface fastethernet3
switchport trunk allowed vlan add 2
interface fastethernet4
switchport trunk allowed vlan add 2
interface fastethernet5
switchport trunk allowed vlan add 2
interface fastethernet6
switchport trunk allowed vlan add 2
interface fastethernet7
switchport trunk allowed vlan add 2
interface fastethernet8
switchport trunk allowed vlan add 2
interface fastethernet9
switchport trunk native vlan 2
interface fastethernet10
switchport trunk native vlan 2
interface fastethernet11
switchport trunk allowed vlan add 2
interface fastethernet12
switchport trunk allowed vlan add 2
interface fastethernet13
switchport trunk allowed vlan add 2
interface fastethernet14
switchport trunk allowed vlan add 2
interface fastethernet15
switchport trunk allowed vlan add 2
interface fastethernet16
switchport trunk allowed vlan add 2
interface fastethernet17
switchport trunk allowed vlan add 2
interface fastethernet18
switchport trunk allowed vlan add 2
interface fastethernet19
switchport trunk allowed vlan add 2
interface fastethernet20
switchport trunk allowed vlan add 2
interface fastethernet21
switchport trunk allowed vlan add 2
interface fastethernet22
switchport trunk native vlan 2
interface fastethernet23
switchport trunk allowed vlan add 2
interface fastethernet24
switchport trunk native vlan 2
ip helper-address all 172.16.0.2 37 42 49 53 137 138
ip route 0.0.0.0 0.0.0.0 172.16.0.150
ip route 10.30.31.0 255.255.255.0 172.16.0.250
Second switch
SW-SRV#show running-config
config-file-header
SW-SRV
v1.2.9.44 / R750_NIK_1_2_584_002
CLI v1.0
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
no cdp run
no spanning-tree
vlan database
vlan 2
exit
voice vlan state disabled
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
ip dhcp relay address 172.16.0.2
ip dhcp relay enable
bonjour interface range vlan 1
hostname SW-SRV
line telnet
password 18c7e97c305303ec56fbb3105666d85721208731 encrypted
exit
line ssh
password 18c7e97c305303ec56fbb3105666d85721208731 encrypted
exit
username cisco password encrypted 18c7e97c305303ec56fbb3105666d85721208731 privilege 15
ip ssh server
snmp-server server
clock timezone " " 0 minutes 0
ip telnet server
interface vlan 1
ip address 172.16.0.248 255.255.0.0
no ip address dhcp
interface vlan 2
name POSTE
ip address 192.168.1.248 255.255.255.0
ip dhcp relay enable
interface fastethernet1
switchport trunk allowed vlan add 2
interface fastethernet2
switchport trunk allowed vlan add 2
interface fastethernet3
switchport trunk allowed vlan add 2
interface fastethernet4
switchport trunk allowed vlan add 2
interface fastethernet5
switchport trunk allowed vlan add 2
interface fastethernet6
switchport trunk allowed vlan add 2
interface fastethernet7
switchport trunk allowed vlan add 2
interface fastethernet8
switchport trunk allowed vlan add 2
interface fastethernet9
switchport trunk allowed vlan add 2
interface fastethernet10
switchport trunk allowed vlan add 2
interface fastethernet11
switchport trunk allowed vlan add 2
interface fastethernet12
switchport trunk allowed vlan add 2
interface fastethernet13
switchport trunk allowed vlan add 2
interface fastethernet14
switchport trunk allowed vlan add 2
interface fastethernet15
switchport trunk allowed vlan add 2
interface fastethernet16
switchport trunk allowed vlan add 2
interface fastethernet17
switchport trunk allowed vlan add 2
interface fastethernet18
switchport trunk allowed vlan add 2
interface fastethernet19
switchport trunk allowed vlan add 2
interface fastethernet20
switchport trunk allowed vlan add 2
interface fastethernet21
switchport trunk allowed vlan add 2
interface fastethernet22
switchport trunk allowed vlan add 2
interface fastethernet23
switchport mode access
switchport access vlan 2
switchport general pvid 2
interface fastethernet24
switchport mode access
switchport access vlan 2
switchport general pvid 2
ip route 0.0.0.0 0.0.0.0 192.168.1.254
ip route 10.30.31.0 255.255.255.0 172.16.0.250
ip route 10.42.2.0 255.255.255.0 192.168.1.251
Here is what I want to do with these switches:
Uplink between the 2 switches on fa 13 for the first and fa 12 on the second
Behind the fa 23 on the second switch, I have a SDSL line between my company and a datacenter wich is hosting my main software.
Behind the fa 24 on the second switch, I have my Firewall wich hosts the ADSL for Internet and which is translating all addresses of the VLAN 1 to the address 192.168.1.254 in order to communicate with the datacenter via the SDSL.
On the native VLAN 1, I have some PCs, servers, the firewal and WiFi controllers.
On the VLAN 2, I have only PCs.
My final objective is to migrate all of the WiFi controllers and PCs in VLAN 2 and to only have servers in VLAN 1.
VLAN 1 and 2 must communicate between them, so I activated IP routing.
I wonder why I accounter some problems of stability for the connection on the SDSL.
In fact: between 7:30 and 10:00 I have no problems of communication between my LAN and the datacenter, passed 10:00 some problems of communications are appearing.
These problems didn't happened before I changed my old SF200 for the SF300, so I really think the problem is coming from the switches configuration.
I turned off CDP because I had some messages about Native VLAN mismatch on fa23 (SDSL).
I hope someone could give me some clue about what goes wrong.I'll try an update of the firmware tomorrow.
The duplex mode is set to auto negociation and in fact on the port fa 23 autoset to full.
Yesterday, I set all ports to mode access except for the uplink ones wich still set to trunk and I moved uplink to the gigabits ports.
Before I do the firmware update from v1.2.9.44 to 1.3.0.62, could you tell me how long this update should take, and, by the way, does it need to rebuild the configuration of the switch?
I'll update the post after the firmware update is done. -
Need help InterVlan Routing on SF300-24P? .
Hello
I really need help with Inter vlan routing via Kerio Controll 7.4.1.
I have several SF300-24P switches (IOS 1.3.0.62) and i have created a several VLAN's.
Vlans: Vlan 10, 100, 200 and interface vlan 213 (for management).
I can ping hosts in the same Vlan via this switches. From switch to host, port is in access mode and between switches ports is in Trunk mode
(also i had a problem here, trunk wasn't working untill i used command: switchport trunk allowed vlan add all).
Also port is in Trunk mode between KERIO and SW1 (switch). interface is in TRUNK mode from switch's side because i don't know how configure interface TRUNK mode on kerio.
On kerio i have configed one physical interface with IP - 172.16.0.1 255.255.255.0 and on the same interface i have created
VLAN 10, VLAN 100 and VLAN 200.
static IP's for this interfaces:
10.0.0.1 255.255.255.0 VLAN 10
192.168.100.1 255.255.255.0 VLAN 100
192.168.200.1 255.255.255.0 VLAN 200
On KERIO i have created DHCP Lease for each VLAN, but i cannot get IP's from DHCP. So i assigned static IP's to computers
(for example for VLAN100 PC, VLAN 200 PC and so on) but they cannot ping each other when they are in different vlans, so inter vlan routing itsnot working. but with static IP on the PC, i can ping every VLAN's IP address on KERIO.
so pls tell me how i must configure inter vlan routing on kerio, is it possible?
or what must i do? where is my mistake? maybe when i put IP on pysical interface?
here is my configs and pls help and give me config example.
config-file-header
SW1
v1.3.0.62 / R750_NIK_1_3_647_260
CLI v1.0
set system mode switch
file SSD indicator plaintext
vlan database
vlan 10,100,200,213
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname SW1
username administrator password encrypted 7fc3774d79570c81cda124d5dcf80b8ae0fcdd6c privilege 15
username cisco password encrypted 1defefd1f4a214009775b2c2b6b961a77da384b5 privilege 15
interface vlan 10
name Staff
interface vlan 100
name Cards
interface vlan 200
name AP's
interface vlan 213
name Management
ip address 172.16.213.1 255.255.255.0
no ip address dhcp
interface fastethernet1
description MANAGEMENT-VLAN
spanning-tree disable
switchport mode access
switchport access vlan 213
interface fastethernet2
spanning-tree disable
switchport mode general
switchport general acceptable-frame-type untagged-only
interface fastethernet3
spanning-tree disable
switchport mode general
switchport general acceptable-frame-type untagged-only
interface fastethernet4
spanning-tree disable
switchport mode access
switchport access vlan 200
interface fastethernet5
spanning-tree disable
switchport mode access
switchport access vlan 200
interface fastethernet6
spanning-tree disable
switchport mode access
switchport access vlan 100
interface fastethernet7
spanning-tree disable
switchport mode access
switchport access vlan 100
interface gigabitethernet1
description Direction-To-SW2 <--- This port is Trunk, but its not showing here for some reason.
spanning-tree disable
interface gigabitethernet2
description Direction-To-KERIO <--- This port is Trunk also. i used: switchport mode trunk on both interfaces
spanning-tree disable
exit
banner login
SW1
config-file-header
SW2
v1.3.0.62 / R750_NIK_1_3_647_260
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end cb0a3fdb1f3a1af4e4430033719968c0
vlan database
vlan 10,100,200,213
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
hostname SW2
username administrator password encrypted 7fc3774d79570c81cda124d5dcf80b8ae0fcdd6c privilege 15
username cisco password encrypted 1defefd1f4a214009775b2c2b6b961a77da384b5 privilege 15
interface vlan 10
name Staff
interface vlan 100
name Cards
interface vlan 200
name AP's
interface vlan 213
name Management
ip address 172.16.213.2 255.255.255.0
no ip address dhcp
interface fastethernet1
description MANAGEMENT-VLAN
spanning-tree disable
switchport mode access
switchport access vlan 213
interface fastethernet2
spanning-tree disable
switchport mode general
switchport general acceptable-frame-type untagged-only
interface fastethernet3
spanning-tree disable
switchport mode general
switchport general acceptable-frame-type untagged-only
interface fastethernet4
spanning-tree disable
switchport mode access
switchport access vlan 200
interface fastethernet5
spanning-tree disable
switchport mode access
switchport access vlan 200
interface fastethernet6
spanning-tree disable
switchport mode access
switchport access vlan 100
interface fastethernet7
spanning-tree disable
switchport mode access
switchport access vlan 100
interface fastethernet8
spanning-tree disable
switchport mode access
switchport access vlan 100
interface gigabitethernet1
description Direction-To-SW1 <--- This port is Trunk also. i used: switchport mode trunk
exit
banner login
SW2
i have excluded many interfaces because hey have same configs.Yes Kerio is capable for routing. i wanted to make InterVlan routing via kerio Ccontroll, but i can't and that's i asked here, i need to know reason.
I have modified 1 switch to L3, and inter vlan routing its now working (without Kerio) and i hope this switches dont have problem when they are DHCP server also.
thanx for help. I Hope i didnot have much mistakes in config. -
VoIp settings for replacing a Cisco 3550 switch with a SF300-24P
I am adding the SF300-24P to an existing set of switches. My backbone switch is a 3560.
The 3550 I am replacing has this config for each port that supports a Shoretel phone
switchport trunk encapsulation dot1q
switchport mode trunk
mls qos trust dscp
global settings include
spaning-tree mode pvst
spanning-tree extend system-id
spanning-tree vlan 1,200 priority 28762
vlan internal allocation policy ascending
all other settings are at default
Any ideas how to replicate this on this new switch? I added the Shoretel mac address range (00-10-49) into the Telephone OUI. The phone gets power, I think it gets a 192.168.6.x address (local subnet), but then it should get an IP 10.6.0.xx on its VLAN - but it doesn't.
Some configs from the backbone are attached. I did not need to configure any of this in the 3550.
Any ideas?
FredHi fred,
The shoretel phone sounds like it is not attaching to tagged vlan 200 on my switch, the shortel voice vlan as per your screen captures.
The Voice VLAN should be tagged on my switch so that phones attach to a Voice VLAN and PC's connected on the back of the VoIP phones attach to the Data Vlan .
I scoped out, excuse the pun, the shoretel site and have attached a white paper on setting vlans and shoretel.
They mention setting option 156 on the DHCP server, so the phone can get vendor specific information etc... But the phones are not attached to the voice vlan , but the untagged data vlan. You gotta figure how to get the shortel phones to attach to vlan 200, or if you are not daisy chaining PC on the back of the phone, make vlan 200 untagged on these FastEthernet switch ports..
I have attached my SF300-48P version of my configuration and some configuration screen shots i took along the way.
Please review carefully that attached shortel document and my screen shots and a real configuration done on my SF300-48P. The configuration should be almost identical to your configuration.
I added vlan 200. and made sure that all ports were in trunk mode, even the Gigabit uplink ports.
All ports by default are in VLAN1 as you can see below
I then added all ports as tagged ports to vlan 200 as you can see below.
For the sake of Spanning tree, I then made all fast ethernet (phone or PC) ports fastports except for the uplink Gigabit ports.
If you are not sure what portfast does , here's a little tutorial I grabbed from cisco.com
Spanning-tree PortFast causes a port to enter the spanning-tree forwarding state immediately, bypassing the listening and learning states. You can use PortFast on switch ports connected to a single workstation or server to allow those devices to connect to the network immediately, instead of waiting for the port to transition from the listening and learning states to the forwarding state.
Caution PortFast should be used only when connecting a single end station to a switch port. If you enable PortFast on a port connected to another networking device, such as a switch, you can create network loops.
When the switch powers up, or when a device is connected to a port, the port normally enters the spanning-tree listening state. When the forward delay timer expires, the port enters the learning state. When the forward delay timer expires a second time, the port is transitioned to the forwarding or blocking state.
When you enable PortFast on a port, the port is immediately and permanently transitioned to the spanning-tree forwarding state.
Your tasks I guess should be , making sure that vendor specific options for the shoretel phones are included in the DHCP configuration and that you somehow attach the shortel phones (even manually) to vlan 200.
For some reason this site adds a zip extension to the end of my running configuration. I used wordpad to look at the file
I am using firmware version 1.0.0.27 on my unit and the userid=admin password i used was admin
I hope this helps.
regards Dave -
Hi
Actually we have the follow diagrame:
When put the SF300-24P on the remote node we have troubles with pass the vlan tag from voice and data on the same port but when put on access port to the vlan voice and data the dispositives have the correct funtion.
someone have something about of this trouble?
the firmeware actually on the switch es 1.2
Best RegardsHi,
We follow the procedure as You said Us, and now the CP3905 learned the vlan correctly through CDP.
This is the Show Run now:
#sh run
interface gi1
spanning-tree link-type point-to-point
exit
vlan database
vlan 320-322
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
no lldp run
interface fastethernet2
lldp med disable
exit
interface vlan 322
ip address 10.1.208.100 255.255.240.0
exit
ip route 0.0.0.0 0.0.0.0 10.1.208.1
[0mMore: , Quit: q or CTRL+Z, One line:
bonjour interface range vlan 1
hostname switch06e3d7
ip ssh server
no snmp-server server
ip telnet server
interface fastethernet2
macro description "ip_phone_desktop | no_ip_phone_desktop"
exit
interface fastethernet3
macro description "ip_phone_desktop | no_ip_phone_desktop"
exit
interface gigabitethernet1
macro description "switch | no_switch | switch"
exit
interface fastethernet2
no macro auto smartport
switchport trunk allowed vlan add 321
switchport trunk native vlan 320
exit
interface gigabitethernet1
!next command is internal.
macro auto smartport dynamic_type switch
[0mMore: , Quit: q or CTRL+Z, One line:
switchport trunk allowed vlan add 320-322
exit
Thanks for Your support
Best Regards,
AJ -
SF300-24P VLAN Confusion - autosmartport not being too smart?
Hi Everyone, first question i've posted, i'll try and give as much information as possible, i'm an extremely quick learner as well and have been around networking for nearly 20 years but this is my first outing into the medium sized VoIP deployment with prioritised LAN traffic and a client that is itching to say "told you so" about using IP phones.
I have 4 x SF300-24P switches in a network i'm deploying, 1 will be adjacent to the router (a draytek Vigor 3200 - 4xWAN Gigabit) and the other 3 will be trunked using the GE/01-GE/03 ports to the main switch and will then distribute through a patch panel to give me 96 network ports with PoE capability where required. There will be 30+ IP Phones on the network, all of which are Yealink T38G SIP handsets.
I want to have two VLAN's - one for regular workstations, and one for IP Phones with the IP Phone VLAN getting high prority for its traffic on the LAN - all documentation makes it sound simple but it doesn't seem to be working the way I think I expect it to. I don't mind the two VLAN's sharing the same IP address space at this time and currently all occupy 10.0.0.0/24 internally.
So, I have 2 questions and a problem.
First, from the factory, the switches are configured that VLAN1 is the default VLAN and that auto-voice VLAN is also VLAN1? Is this right?
Second, i'm having trouble determining the difference in terminology for port types between general, access, trunk etc - obviously trunk is between switches and carries VLAN information through to the next segment of the network.
My main problem seems to be with auto-voice VLAN and smartport. If I enable smartport, the switch figures out through LLDP that the port is used by an IP Phone + Desktop (excellent, this is what I want it to do) so then puts the handsets in VLAN1 but then the handsets start to become invisible on the network after 2-3 minutes, the handsets then reboot because they've detected a network drop out and then reconnect, re-register at the voice server and are visible and contactable for 2-3 minutes then the loop begins again.
If I disable smartport, the problem goes away.
Am I unreasonably expecting that any user can unpack an IP phone and (subject to provisioning on the server), plug it into any port on the network and it will figure out that it's a phone, not a PC and then prioritise its traffic?
What I want to avoid is the possibility of internal bandwidth lag if someone copies a large file over the network and people are using the phones that the phone users don't get packet loss or audio instability because of the file copy. The internet side will be fine, the Vigor3200 has QoS facilities built in and i've had good success on smaller networks with these routers.
Ideally I need a semi-planned network setup where people with WiFi SIP clients will also get some priority.
I have set QoS on the handsets to match DSCP46 from the switches - can the traffic be manipulated this way or does it already do that in the DSCP to Queue setup which automatically puts anything above 40 in Queue 4 (high priority).
All help very greatfully received.
JamesHello James,
Welcome to the forums!
About the default settings. The switch comes with vlan1 as the default vlan for all traffic.
Here is a quick overview of the port settings
access - one vlan
trunk - multiple vlans
general - multiple vlans (had additional options)
When using the auto voice-vlan, you can have your port set as access for vlan 1 and when the switch see a phone connected, it will join the voice vlan also. This allow the ports to be dynamic. It is not necessary to do this. You can create all ports as trunk ports that are part of both your default vlan and your voice vlan.
The benifits of auto-voice vlan
-phones are discovered and joined to the vlan dynamically
-predetermined QoS settings
-security in that you can have your port set to access
This is a relatively basic overview.
As for the problem you are seeing. I would recommend that you check the firmware of the switch and upgrade if needed. While it may not have anything to do with the problem at hand, it will help prevent any future issues.
I would suggest disabling the Green Ethernet, which can be found under the port management section. If you continue to see the problem after that, I would recommend giving us a call at the support center. We will be able to look a little closer to what is happening.
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html -
hi I Have been facing a problem, like when we are connecting the Aironet LWAPP indoor Accesspoint to Cisco SF300-24P Switch, we are getting some error like LOW POWER...means accesspoint not recieving enough power from POE Switch.
As per Cisco Datasheet for 300 series Switch the model number is SF300-24P and power dedicated to POE is 180 W and all 24ports do support POE at 7.5Wand 12 portsSupport Maximum Power at 15.0W.Required Power for Aironet Accesspoint through POE Switch maximum is 12.4W is Enough.So can anyone please suggest what to do now.Hi Nenad, if you administratively remove auto smart port, auto voice vlan will also be shut down.
Your original post consists of some important details-
IP phones are directly connected on the switch and PC's are connected on the phone, so the PC's get IP's through the phone. FE ports are configured vlan 10 untagged vlan 20 tagged.
This is expected and good
Some PC's can't get IP's,for example client turn the computer on and can't get IP, sometimes ipconfig /release, ipconfig /renew on cmd helps sometimes I just unplug network cable from pc and plug it again and it works, I tried to replace the IP phone i didn't help.
When this happens, it usually indicates a convergence issue with spanning tree. If portfast (edge port) does not negotiate, the port will progress through the spanning-tree states, listening, learning forwarding, which can make a long time to receive DHCP / LAN connectivity.
Sometimes that issue change configuration on switch port for example client announce that he have a problem, I connect to switch via the web and see that port on witch is client connected have configuration vlan 10 data tagged vlan 20 voice tagged instead of vlan 10 untagged vlan 20 tagged...very strange.
This statement indicates a macro issue. The macro detects connection types through LLDP and CDP advertisements. If the switch is dynamically assigning vlan id or vlan tag, it means the macro is writing that configuration. Most likely, you will need to go to the macro and re-write the macro to show the native vlan to be 10.
So, I would recommend to do this- Go to the smart port built-in macro, edit all of the macro like this example
-Tom
Please rate helpful posts -
When I use Explored, usually I display my pages in English, but Explore has a feature that you can point any word and it is translated from English to Spanish (one one word at the time, not the complete page), does it is available in Firefox?
I do not know the answer but if you look through the Add-ons under [https://addons.mozilla.org/en-US/firefox/search/?q=translation translate] you may find something suitable. There is of course also the well known Google translate [http://translate.google.com/#es|en|choose%20the%20language%20combinations%2C%20and%20can%20handle%20single%20words%0Awith%20some%20odd%20results service]
-
When I try to install Itunes, I get this error: (translated from Norwegian) There was a network error while trying to read from the file: C: \ windows \ installer \ iTunes.msi I have tried many times to reinstall, but nothing helps, please help me.
(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time? -
Translation from CS5 to Cloud doesn't work correct, navi and linked images are broken.
Translation from CS5 to Cloud doesn't work correct, <navi> and linked images are broken.
The data of CS5 was created at another PC. I installed Cloud version into two different PC. One has had the site data since dreamweaver CS5 and it works correct in Cloud version. Another PC got the site data from remote server and it doesn't work correct. <navi> and linked image are broken.Another PC got the site data from remote server and it doesn't work correct. <navi> and linked image are broken.
This implies your site is not properly defined in DW. Go to Site > Manage Sites.
Or simply go to your other installation of DW and export the site definition file from Manage Sites.
Save it to a flash stick or other removable drive. Then import the STE file into your 2nd installation of DW.
Nancy O. -
Hello B2B Gurus,
I am able to process B2B inbound files successfully from Trading Partner --> B2B --> BPEL. When it comes to BPEL i am not able to parse/transform the received XML as i am getting selection failures in assign and empty nodes in transformation. When i look at the input XML payload which i received in ReceiveB2BConsume Payload i observed that i am getting namespace as " xmlns="NS_495C37A0921C418BB66A86A6E75B2CA120070312140549" instead of actual namespace xmlns="urn:oracle:b2b:X12/V4010/856" which is in my XSD as well and i am getting the XML start tag <?xml version="1.0" encoding="UTF-8" ?> 2 times. :
<?xml version="1.0" encoding="UTF-8" ?>
<?xml version="1.0" encoding="UTF-8" ?>
<Transaction-856 xmlns="NS_495C37A0921C418BB66A86A6E75B2CA120070312140549" mlns:xsi="http://www.w3.org/2001/XMLSchema-instance" XDataVersion="1.0" Standard="X12" Version="V4010" CreatedDate="2013-08-21T16:33:57" CreatedBy="XEngine_2956" GUID="{00C28978-0AA1-11E3-88B9-80C16E7DC6DA}">
<Internal-Properties>
</Transaction-856>
I went back and checked the XSD which i loaded in the B2B Console and i am having the following namespace
"<xsd:schema xmlns="urn:oracle:b2b:X12/V4010/856" targetNamespace="urn:oracle:b2b:X12/V4010/856" xmlns:xsd="http://www.w3.org/2001/XMLSchema" version="1.0" elementFormDefault="qualified">"
I am not sure why the XML translated from EDI in B2B console has the different namespace and XML start tag 2 times. Can you please help me resolve the issue. Let me know if i am missing anything.
Thanks in Advance..Hi,
Please set property as b2b.setDynamicNameSpace=false.
To use EDI ecs and xsd files from Oracle B2B 10g version, set this property to true.
When using EDI ecs and xsd files in Oracle B2B 11g which were used in Oracle B2B 10g, the XEngine may generate dynamic namespace for the translated xml. For example,
xmlns="NS_31CA8D0F33324F95A0BF15D85539C27E20060518215520"
To turn off dynamic namespace generation for inbound EDI messages, set this property to false.
Thanks
Satendra Pare -
Error message "A I/0-error has occured in the file" (free translated from Swedish). What to do?
Hello!
I keep getting the error message "A I/O-error has occured in the file" (free translated from Swedish) when I try to save changes to a .ai-file in Illustrator. I have never experienced that before. Does anyone have any idea what the problem is? Greatful for a quick answer, since I can't get any work done =/ Thank you in advance!alu,
If it is a specific file, one thing often tried first is to create a new document and File>Place the corrupted one to see how much may be rescued that way (remember to tick Paste remembers Layers in the Layer palette flyout/dropdown first, and to untick it afterwards).
Here is a website where you can see whether it can rescue the file, and if it can, you may pay for a subscription to have it done,
http://www.recoverytoolbox.com/buy_illustrator.html
and another similar website,
http://markzware.com/adobe-software/fix-illustrator-file-unknown-error-occurred-pdf2dtp-fi le-recovery/
As far as I remember, the former is for Win and the latter for Mac.
Here are a few pages about struggling with it yourself:
http://daxxter.wordpress.com/2009/04/16/how-to-recover-a-corrupted-illustrator-ai-file/
http://helpx.adobe.com/illustrator/kb/troubleshoot-damaged-illustrator-files.html
http://kb2.adobe.com/cps/500/cpsid_50032.html
http://kb2.adobe.com/cps/500/cpsid_50031.html
http://helpx.adobe.com/illustrator/kb/enable-content-recovery-mode-illustrator.html
If it is not just a certain file, you may have a look at the list.
The following is a general list of things you may try when the issue is not in a specific file (you may have tried/done some of them already); 1) and 2) are the easy ones for temporary strangenesses, and 3) and 4) are specifically aimed at possibly corrupt preferences); 5) is a list in itself, and 6) is the last resort.
1) Close down Illy and open again;
2) Restart the computer (you may do that up to 3 times);
3) Close down Illy and press Ctrl+Alt+Shift/Cmd+Option+Shift during startup (easy but irreversible);
4) Move the folder (follow the link with that name) with Illy closed (more tedious but also more thorough and reversible);
5) Look through and try out the relevant among the Other options (follow the link with that name, Item 7) is a list of usual suspects among other applications that may disturb and confuse Illy, Item 15) applies to CC, CS6, and maybe CS5);
Even more seriously, you may:
6) Uninstall, run the Cleaner Tool (if you have CS3/CS4/CS5/CS6/CC), and reinstall.
http://www.adobe.com/support/contact/cscleanertool.html -
Report Painter - Translation from Transaction Currency
Hi,
I have set up a report painter report using "Translation from Transaction Currecny" as one of the key figures in one of the columns in the report. When I execute the report it prompts me for the target currency and the ER type which is what I was expecting. EG I want to translate actuals to say AUD at budget rate (type P)
My question is.... I add a second column again using the same key figure ""Translation from Transaction Currecny" which I want to exchange using a different Exchange rate type.E.g I want to translate actuals to AUD using the forecast rate (type Q). However, when I execute the report I was expectiong to be prompted twice for the target currency and exchange rate type but it still only prompts me once.
Does that mean that using the key figure that I cannot use it in more than one column in the report?
I hope this makes sense.
Thanks...Add custom reports to an existing Report Tree (SERP)
For example:
Add custom report to: Project System/Information System/Financials/u2026
Find u201CPS91u201D from SERP
Add a report to PS91
The trick is find the existing report tree related to standard main menu.
Or create a new report tree where you house all custom or selected reports in one place.
May also consider using area menu (SE43): create a structure, for example, to house all custom reports. A useful tool to manage custom/specifc reports -
RADIUS authentication SF300-24P
RADIUS authentication SF300-24P
We have just purchased 20x SF300-24P switches to be installed at our remote offices and we are unable to get RADIUS authentication to work. We already use RADIUS on all our primary network CISCO switches (e.g. 4506s¸ 3560s, 3750s, AP1231Gs,etc) and these work fine so we know the RADIUS server is working.
We are trying to use RADIUS authentication to gain management access onto these switches. Quite simply although we can see that the RADIUS server is accepting the username and password being sent, however the switch says “authentication failed” when to receives the response. We are using Microsoft NPS RADIUS Clients for authentication purposes.
We have upgrade the switches to the latest firmware 1.1.2.0, via the console it seems to have a very cut down IOS version so we cannot use the typical CISCO command set to configure the RADIUS as we normally would. Looking at the web GUI there seems to be a number of options missing including the Accounting port. When debugging is switch on there is no indication to say that any of the settings have been misconfigured.
Any advice you could offer would be gratefully received.
Mike LewisHere is the documentation excerpt-
For the RADIUS server to grant access to the web-based switch configuration
utility, the RADIUS server must return cisco-avpair = shell:priv-lvl=15.
User authentication occurs in the order that the authentication methods are
selected. If the first authentication method is not available, the next selected
method is used. For example, if the selected authentication methods are RADIUS
and Local, and all configured RADIUS servers are queried in priority order and do
not reply, the user is authenticated locally.
If an authentication method fails or the user has insufficient privilege level, the user
is denied access to the switch. In other words, if authentication fails at an
authentication method, the switch stops the authentication attempt; it does not
continue and does not attempt to use the next authentication method.
Of course the point of interest here is the second paragraph. The initial wording is the behavior you want. The second portion is very open for interpretation (I do agree it is somewhat ambiguous but consistent with the switch behavior). When I read the example and it says the Radius is busy or not responding then you will authenticate locally. Which seems fair enough. But what it doesn't say, is if you can use one or the other, but instead it seems based on preference failure.
-Tom
Please rate helpful posts
Maybe you are looking for
-
How to erase all content in MacBook Pro?
I need to erase all data and content in my MacBook. How can I do this?
-
Can't preview jpg in Camera RAW filter after Photoshop update
I just updated my Photoshop cc and now when I open jpg in the Camera RAW filter. I get a blue box with big X.
-
Multiple components in a gridbag layout cell
Is it possible to have two components in one cell of a grid bag layout? Say, a textfield box and some text to its immediate right? If so, can someone post an example? Thanksmuch.
-
BUG:text-align:right; inline style not working on read-only af:InputText
Hello, A bug in how af:InputText works if readonly=true. I have an af:InputText that has "text-align:right;" for the InlineStyle. The inputText is inside of an af:Column in af:Table. If the inputtext is readonly=false, it works properly and renders r
-
hi my ipod 5th gen is stuck in recovery mode ive tried everything and nothing is working