Transport Protocol Error
We are getting the following error while running a program to dowload files from a secure ftp server. The same code runs from a local machine but it fails from a server machine.
We are using lotus domino serer to run the agent on the sever
We would be greatful if you could throw some light on this.
09/16/2005 10:11:04 AM HTTP JVM: SSH Object = com.sshtools.j2ssh.SshClient@1eef26b5
09/16/2005 10:11:04 AM HTTP JVM: [INFO] TransportProtocolCommon - -Starting transport protocol
09/16/2005 10:11:04 AM HTTP JVM: [INFO] TransportProtocolCommon - -Registering transport protocol messages with inputstream
09/16/2005 10:11:04 AM HTTP JVM: [ERROR] TransportProtocolCommon - -The Transport Protocol thread failed <java.lang.NoClassDefFoundError: javax/crypto/KeyAgreement>java.lang.NoClassDefFoundError: javax/crypto/KeyAgreement
at com.sshtools.j2ssh.transport.kex.DhGroup1Sha1.onInit(Unknown Source)
at com.sshtools.j2ssh.transport.kex.SshKeyExchange.init(Unknown Source)
at com.sshtools.j2ssh.transport.TransportProtocolCommon.run(Unknown Source)
The problem was occuring because a mistake has been made in the notes.ini file regarding the classpath entries. The wrong classpath entry is deleted and the program works fine now.
Notes.ini is the file which contains the configuration settings of the lotus server.
Regards,
Rajiv
Similar Messages
-
Getting error using the EMail Transport Protocol
Hi Gurus,
I am using the EMail Transport Protocol (Custom Document over Generic Exchange).
I am able to send the document using this protocol to a exchange server successfully. but when tried to receive the document from exchange server to Oracle B2B. I am getting the below error.
Description: Unable to identify the document protocol of the message
StackTrace:
Error -: AIP-50083: Document protocol identification error
at oracle.tip.adapter.b2b.engine.Engine.identifyDocument(Engine.java:3245)
at oracle.tip.adapter.b2b.engine.Engine.processIncomingMessage(Engine.java:1666)
at oracle.tip.adapter.b2b.engine.Engine.incomingContinueProcess(Engine.java:2574)
at oracle.tip.adapter.b2b.engine.Engine.handleMessageEvent(Engine.java:2444)
at oracle.tip.adapter.b2b.engine.Engine.processEvents(Engine.java:2399)
at oracle.tip.adapter.b2b.data.MsgListener.onMessage(MsgListener.java:527)
at oracle.tip.adapter.b2b.data.MsgListener.run(MsgListener.java:374)
at java.lang.Thread.run(Thread.java:534)
As per my knowledge all necessary properties are reaching Oracle B2B. Please go through the b2b.log content below.
2009.05.14 at 13:16:56:994: Thread-20: B2B - (DEBUG)
Protocol = Email
Version = null
Transport Header
SUBJECT:Test Message from SP
ACTION_NAME:CSVProcess
DATE:Thu, 14 May 2009 12:16:46 GMT
CONNECTION:close
TO:[email protected]
CONTENT-TYPE:multipart/mixed; boundary="----=_Part_3_11019994.1242303406228"
MIME-VERSION:1.0
X-MAILER:IPTransport
FROM_PARTY:EmailTP_GI
DOCTYPE_NAME:CSVProcess_DT
DOCTYPE_REVISION:1.0
FROM:EmailTP_GI
MESSAGE-ID:AC18E52A1213F0D9FB9000001629E7B0
RECEIVED:from INBAAMPC00933 ([172.24.229.42]) by vitz.techm.com (IceWarp 9.1.1) with ESMTP id VRE73645 for <[email protected]>; Thu, 14 May 2009 13:16:45 +0100
TO_PARTY:EmailSP_GI
Content-Type:application/b2b; name="Test Message from SP"
Sample Email Test1
Sample Email Test1
Sample Email Test1
Sample Email Test1
Sample Email Test1
Sample Email Test1
Sample Email Test1
Sample Email Test1
Sample Email Test1
Sample Email Test1
2009.05.14 at 13:16:57:057: Thread-20: B2B - (DEBUG) DBContext beginTransaction: Enter
2009.05.14 at 13:16:57:057: Thread-20: B2B - (DEBUG) DBContext beginTransaction: Transaction.begin()
2009.05.14 at 13:16:57:057: Thread-20: B2B - (DEBUG) DBContext beginTransaction: Leave
2009.05.14 at 13:16:57:057: Thread-20: B2B - (DEBUG) InterfaceListener:onMessage - Invoke inbound callout - null - null
2009.05.14 at 13:16:57:057: Thread-20: B2B - (DEBUG) InterfaceListenersyncAckEBMSchecking header names
2009.05.14 at 13:16:57:057: Thread-20: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:insertNativeEvtTblRow(2 params) Enter
2009.05.14 at 13:16:57:088: Thread-20: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:insertNativeEvtTblRow(2 params) Exit
2009.05.14 at 13:16:57:088: Thread-20: B2B - (DEBUG) oracle.tip.adapter.b2b.transport.InterfaceListener:onMessage sendEventtrue
2009.05.14 at 13:16:57:088: Thread-20: B2B - (DEBUG) DBContext commit: Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:onMessage Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) DBContext beginTransaction: Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) DBContext beginTransaction: Transaction.begin()
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) DBContext beginTransaction: Leave
2009.05.14 at 13:16:57:104: Thread-19: B2B - (INFORMATION) oracle.tip.adapter.b2b.engine.Engine:processEvents Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processEvents begin transaction
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) DBContext beginTransaction: Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) DBContext beginTransaction: Leave
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:handleMessageEvent Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:incomingContinueProcess Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:getWireMessage Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:getWireMessage Exit
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:formTransportMessage Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:formTransportMessage Exit
2009.05.14 at 13:16:57:104: Thread-19: B2B - (INFORMATION) oracle.tip.adapter.b2b.engine.Engine:processIncomingMessage Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processIncomingMessage Identify Business Protocol
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processIncomingMessage Do Unpack using the BP specific package class
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:unpack:Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:doUnpack:Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMessageContent:Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processInputStreamOrStringMessage:Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processInputStreamOrStringMessage:Content Type = application/b2b; name="Test Message from SP"
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMimeBodyPart:Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMimeBodyPart:newMimeBodyPart.getAllHeaders()
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMimeBodyPart:getting content info
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:setContentTypeInfo:Enter
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:setContentTypeInfo:Exit
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMimeBodyPart:newMimeBodyPart.getContent()
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMimeBodyPart:check content type(InputStream/String)
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMimeBodyPart:contentObj instanceof InputStream
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMimeBodyPart:addMimeBodyPartToMessageInfoString()
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMimeBodyPart:Exit
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processInputStreamOrStringMessage:Exit
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:processMessageContent:Exit
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:doUnpack:Exit
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) MimePackaging:unpack:Exit
2009.05.14 at 13:16:57:104: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processIncomingMessage Decode the Incoming Message into B2B Message
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:GenericExchangePlugin:decodeIncomingMessage Enter
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:GenericExchangePlugin:decodeIncomingMessage Number of Components = 1
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:decodeIncomingMessage Transport Protocol = {Email}
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:decodeIncomingMessage fromTPoveride = null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:decodeIncomingMessage fromParty = EmailTP_GI tmpFromParty :EmailTP_GI
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:decodeIncomingMessage fromTPName ..GOT FROM CACHE= null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:decodeIncomingMessage Remote TP Name = null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) calling setInitiatingPartyId() changing from null to TPName: null Type: Generic Identifier Value: EmailTP_GI
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:decodeIncomingMessage toTPoveride = null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:decodeIncomingMessage Host TP Name = null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:decodeIncomingMessage fromParty = EmailTP_GI
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) calling setFromPartyId() changing from null to TPName: null Type: Generic Identifier Value: EmailTP_GI
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) calling setToPartyId() changing from null to TPName: null Type: Generic Identifier Value: [email protected]
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:GenericExchangePlugin:decodeIncomingMessage security info NULL
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.exchange.generic.GenericExchangePlugin:GenericExchangePlugin:decodeIncomingMessage Exit
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processHubMessage Enter
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processHubMessage toTP [email protected]
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processHubMessage hubUrl null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processHubMessage Exit
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processIncomingMessage ProtocolCollabId = null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processIncomingMessage CollaborationName null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:checkDuplicate Enter
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:checkDuplicate check non-RosettaNet Message
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:checkDuplicate Exit
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:processIncomingMessage Protocol Collaboration Id : null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.document.custom.CustomDocumentPlugin:identifyIncomingDocument Enter
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.document.custom.CustomDocumentPlugin:identifyIncomingDocument Exit
2009.05.14 at 13:16:57:119: Thread-19: B2B - (ERROR) Error -: AIP-50083: Document protocol identification error
at oracle.tip.adapter.b2b.engine.Engine.identifyDocument(Engine.java:3245)
at oracle.tip.adapter.b2b.engine.Engine.processIncomingMessage(Engine.java:1666)
at oracle.tip.adapter.b2b.engine.Engine.incomingContinueProcess(Engine.java:2574)
at oracle.tip.adapter.b2b.engine.Engine.handleMessageEvent(Engine.java:2444)
at oracle.tip.adapter.b2b.engine.Engine.processEvents(Engine.java:2399)
at oracle.tip.adapter.b2b.data.MsgListener.onMessage(MsgListener.java:527)
at oracle.tip.adapter.b2b.data.MsgListener.run(MsgListener.java:374)
at java.lang.Thread.run(Thread.java:534)
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:handleExceptionBeforeIncomingTPA Enter
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:XXX: handleInboundException Enter
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:XXX: handleInboundException Error message is Error -: AIP-50083: Document protocol identification error
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:XXX: isFARequired Enter
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:XXX: isFARequired {SUBJECT=Test Message from SP, ACTION_NAME=CSVProcess, DATE=Thu, 14 May 2009 12:16:46 GMT, CONNECTION=close, [email protected], CONTENT-TYPE=multipart/mixed; boundary="----=_Part_3_11019994.1242303406228", MIME-VERSION=1.0, X-MAILER=IPTransport, FROM_PARTY=EmailTP_GI, DOCTYPE_NAME=CSVProcess_DT, DOCTYPE_REVISION=1.0, FROM=EmailTP_GI, MESSAGE-ID=AC18E52A1213F0D9FB9000001629E7B0, RECEIVED=from INBAAMPC00933 ([172.24.229.42]) by vitz.techm.com (IceWarp 9.1.1) with ESMTP id VRE73645 for <[email protected]>; Thu, 14 May 2009 13:16:45 +0100, TO_PARTY=EmailSP_GI, Content-Type=application/b2b; name="Test Message from SP"}
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:XXX: isFARequired returning false
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:XXX: handleInboundException FA not required
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:handleInboundException Updating Error Message: Error -: AIP-50083: Document protocol identification error
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Enter
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Wire message found
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Creating new b2berror object
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState enum0 not null
2009.05.14 at 13:16:57:119: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Updating wire message error information
2009.05.14 at 13:16:57:135: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Updating wire message protocol message id
2009.05.14 at 13:16:57:151: Thread-20: B2B - (DEBUG) DBContext commit: Transaction.commit()
2009.05.14 at 13:16:57:151: Thread-20: B2B - (DEBUG) DBContext commit: Leave
2009.05.14 at 13:16:57:370: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Updating wire message payload storage
2009.05.14 at 13:16:57:386: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Creating new business message
2009.05.14 at 13:16:57:386: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:insertMsgTblRow Enter
2009.05.14 at 13:16:57:386: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:insertMsgTblRow toparty name null
2009.05.14 at 13:16:57:386: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:insertMsgTblRow toparty type and value Generic [email protected]
2009.05.14 at 13:16:57:386: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:insertMsgTblRow BusinessAction for the given name null null
2009.05.14 at 13:16:57:401: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Updating business message error information
2009.05.14 at 13:16:57:401: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateWireBusinessToErrorState Exit
2009.05.14 at 13:16:57:401: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:handleInboundException Updating Native Event Tbl Row
2009.05.14 at 13:16:57:401: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:DbAccess:updateNativeEvtTblRow Enter
2009.05.14 at 13:16:57:401: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:updateNativeEvtTblRow msgInfo.id = AC18E52A1213F0D9FB9000001629E7B0
2009.05.14 at 13:16:57:401: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.msgproc.DbAccess:
** DbAccess:updateNativeEvtTblRow:tip_wireMsg protocolCollabID = null
2009.05.14 at 13:16:57:433: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:handleInboundException notifying App
2009.05.14 at 13:16:57:433: Thread-19: B2B - (DEBUG) Engine:notifyApp Enter
2009.05.14 at 13:16:57:433: Thread-19: B2B - (DEBUG) notifyApp:notifyApp Enqueue the ip exception message:
<Exception xmlns="http://integration.oracle.com/B2B/Exception" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance">
<correlationId>null</correlationId>
<b2bMessageId>AC18E5411213F0DCB100000013829EB0</b2bMessageId>
<errorCode>AIP-50083</errorCode>
<errorText>Document protocol identification error</errorText>
<errorDescription>
<![CDATA[Machine Info: (INBAAMPC00883)
Description: Unable to identify the document protocol of the message
StackTrace:
Error -: AIP-50083: Document protocol identification error
at oracle.tip.adapter.b2b.engine.Engine.identifyDocument(Engine.java:3245)
at oracle.tip.adapter.b2b.engine.Engine.processIncomingMessage(Engine.java:1666)
at oracle.tip.adapter.b2b.engine.Engine.incomingContinueProcess(Engine.java:2574)
at oracle.tip.adapter.b2b.engine.Engine.handleMessageEvent(Engine.java:2444)
at oracle.tip.adapter.b2b.engine.Engine.processEvents(Engine.java:2399)
at oracle.tip.adapter.b2b.data.MsgListener.onMessage(MsgListener.java:527)
at oracle.tip.adapter.b2b.data.MsgListener.run(MsgListener.java:374)
at java.lang.Thread.run(Thread.java:534)
]]>
</errorDescription>
<errorSeverity>2</errorSeverity>
</Exception>
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) Engine:notifyApp Exit
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:handleInboundException Updated the Error Message Successfully: Error -: AIP-50083: Document protocol identification error
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:XXX: handleInboundException Exit
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:handleExceptionBeforeIncomingTPA Exit
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:incomingContinueProcess Exit
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:handleMessageEvent Exit
2009.05.14 at 13:16:57:448: Thread-19: B2B - (INFORMATION) oracle.tip.adapter.b2b.engine.Engine:processEvents Exit
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) DBContext commit: Enter
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) DBContext commit: Transaction.commit()
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) DBContext commit: Leave
2009.05.14 at 13:16:57:448: Thread-19: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:onMessage Exit
Kindly look into this.
Regards,
VithalHi Nandagopal,
I have configured email idc to send the payload as an attachment. & the attachment I am trying is send is a simple text file. So I am stuck here, how can I check against xPath for the mail :(.
I have copied the sample message below which is there in the SMTP server & ready to be fetched by Oracle B2B. This is how message looks like in the exchange server, before it gets consumed by Oracle B2B.
============================================================
Message-ID: AC18E52A121544A46D4000001629E840
DATE: Mon, 18 May 2009 15:15:02 GMT
From: [email protected]
FROM: EmailTP_GI
To: [email protected]
Subject: Test Message from SP
Mime-Version: 1.0
Content-Type: multipart/mixed;
boundary="----=_Part_6_17282414.1242659702625"
X-Mailer: IPTransport
ACTION_NAME: CSVProcess
DOCTYPE_NAME: CSVProcess_DT
FROM_PARTY: EmailTP_GI
DOCTYPE_REVISION: 1.0
TO_PARTY: EmailSP_GI
Connection: close
------=_Part_6_17282414.1242659702625
Content-Type: application/b2b; name="Test Message from SP"
Content-Transfer-Encoding: base64
Content-Disposition: attachment; filename="Test Message from SP"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------=_Part_6_17282414.1242659702625--
======================================================
Regards,
Vithal -
Transport protocol version error in Integration Directory API
Hi All,
I am trying to create SOAP receiver communication channel using Java-only PI 7.31 directory APIs. I have passed all the required parameters to the CommunicationChannelIn service, but it's throwing error - "Enter at least one object key for operation 'create'".
When I tried to test the service through WS Navigator, it's giving exception - "Enter a value for attribute 'Transport Protocol Version'" which doesn't exists in case of SOAP adapter creation.
Has anybody come across this issue? If the adapter metadata does not specify any transport protocol version, then shouldn’t the validation checks in CommunicationChannelIn service provider proceed without errors on a blank value for this attribute?
Note: I have gone through all the SCN blogs, discussion threads we have on topics related to Integration Directory API.
Thanks in advance for all the help and suggestions.
Regards,
Yashu VyasHi All,
I am trying to create SOAP receiver communication channel using Java-only PI 7.31 directory APIs. I have passed all the required parameters to the CommunicationChannelIn service, but it's throwing error - "Enter at least one object key for operation 'create'".
When I tried to test the service through WS Navigator, it's giving exception - "Enter a value for attribute 'Transport Protocol Version'" which doesn't exists in case of SOAP adapter creation.
Has anybody come across this issue? If the adapter metadata does not specify any transport protocol version, then shouldn’t the validation checks in CommunicationChannelIn service provider proceed without errors on a blank value for this attribute?
Note: I have gone through all the SCN blogs, discussion threads we have on topics related to Integration Directory API.
Thanks in advance for all the help and suggestions.
Regards,
Yashu Vyas -
XI protocol error occurred in abap proxy scenario- plz
Scenario is asynchronous
Http -> XI ->R/3(abap server proxy)
sender: Through http client
receiver is abap server proxy
<u>Repository objects:</u>
Sender: sender_DT, sender_MT, sender_MI(outbound asynchronous)
Receiver: imported RFC from R/3 client 550, receiver_MI(which has message type refered to the imported RFC)
Interface mapping: source=sender_MI, receiver_MI.
Proxy generated on R/3 client 550 for receiver_MI.
<u>Configuartion objects:</u>
Sender: business service, no comm channel since http sender.
receiver: R/3 business system
Comm channel: receiver_cc type of XI.
transport protocol: http
message protocol : XI 3.0, since both XI and R/3 on webas 6.4
addressing type: URL
target host: diamond
service number: 8005
path: /sap/xi/engine?type=entry
Authentiction data:
user name: user22
passwrod; correct
logon client: 400 which is the same client I developed ll the design and config objects.
Recevr determinaion, interface determination and recevr agrrement looks fine.
The error iam getting is:
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- <!-- Call Adapter
-->
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
<SAP:Category>XIProtocol</SAP:Category>
<SAP:Code area="MESSAGE">LOOP_IN_MESSAGE_ROUTING</SAP:Code>
<SAP:P1>is.05.diamond</SAP:P1>
<SAP:P2>IS</SAP:P2>
<SAP:P3>XI</SAP:P3>
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>XI protocol error occurred</SAP:Stack>
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
<b>
Please reply , your help is appreciated.</b>
Thanks
KKStefan thanks,
I tried as you suggesetd putting the info of R/3 for
server: diamond
port: 8005
client: 550
user id: user05
pwd: correct
But I get the below error, suggest me what permission should this userid have?
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- <!-- Call Adapter
-->
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="INTERNAL">HTTP_RESP_STATUS_CODE_NOT_OK</SAP:Code>
<SAP:P1>401</SAP:P1>
<SAP:P2>Unauthorized</SAP:P2>
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText><!DOCTYPE html PUBLIC"-//W3C//DTD HTML 4.01Transitional//EN"><html><head><title>Logon Error -
What is difference between transport protocol and message protocol
what is difference between transport protocol and message protocol
please give definition and small explanationHi,
Transport protocol gives information about outside of message details, kind of system, security details.
A transport protocol is a network protocol that has the capability of transferring some payload from one node to another, thus providing some level of transparency from the underlying network.
Transport protocols are used as a mechanism to move payloads around a network. Typically, a payload will have a transport binding associated with it. For example, SOAP (acting as a payload) has a predetermined binding for HTTP (a transport protocol).
Some common transport protocols include: HTTP, HTTP-R, SMTP and BEEP.
Message protocol gives you an idea of message type XI payload
http://help.sap.com/saphelp_nw04/helpdata/en/b6/0b733cb7d61952e10000000a11405a/content.htm -
B-channel oos and protocol error 510
Dear all,
I have some some issue couple of days ago. The telephony system of my client worked well and suddenly the cannot make external calls via E1. I checked the config and for me it seems to be ok. When I checked the SDL file, I can see the B channel out of service error message following by the
"MGCP PROTOCOL ERROR: <S1/SU1/DS1-0/[email protected]> CRCX error code: 510". They have A CUCM 6.0 and Cisco 2821 as gateway with 12.4 (25f) advance IP service IOS.
I perform the following actions without success:
-From the CUCM in the advance service I forced the Bchannel to bring it in service,
- no mgcp/mgcp, -reboot the CUCM and the Gateway,
-reset the controller throug CUCM,... in vain.
They contacted telco and has confirm that everything seems to be ok. Find below the information that can help you to undestand better
#sh run brief
Building configuration...
Current configuration : 4859 bytes
version 12.4
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname ATD-CCM-GW
boot-start-marker
boot-end-marker
security authentication failure rate 3 log
security passwords min-length 6
logging buffered 51200 debugging
aaa new-model
aaa authentication login default local
aaa authentication login local_authen local
aaa authorization exec default local
aaa authorization exec local_author local
aaa session-id common
clock timezone A 1
network-clock-participate slot 1
network-clock-select 1 E1 1/1/0
ip cef
ip domain name xx.xxxx.xxx
ip host ATD-CCM1 10.10.10.100
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
isdn switch-type primary-net5
isdn logging
voice-card 0
dspfarm
dsp services dspfarm
voice-card 1
no dspfarm
no voice call carrier capacity active
voice rtp send-recv
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
codec preference 3 g729br8 bytes 40
voice class h323 1
h225 timeout tcp establish 3
crypto pki trustpoint TP-self-signed-635937996
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-635937996
revocation-check none
rsakeypair TP-self-signed-635937996
crypto pki certificate chain TP-self-signed-635937996
certificate self-signed 01
application
service alternate Default
controller E1 1/1/0
framing NO-CRC4
pri-group timeslots 1-31 service mgcp
interface GigabitEthernet0/0
description to_CCM
ip address 10.10.10.254 255.255.255.0
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
interface Serial1/1/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
isdn bind-l3 ccm-manager
isdn bchan-number-order ascending
isdn sending-complete
no cdp enable
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 10.10..253
ip http server
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
logging trap debugging
control-plane
voice-port 1/0/0
timing hookflash-out 50
voice-port 1/0/1
signal groundStart
timing hookflash-out 50
voice-port 1/0/2
signal groundStart
timing hookflash-out 50
voice-port 1/0/3
signal groundStart
timing hookflash-out 50
voice-port 1/1/0:15
ccm-manager fallback-mgcp
ccm-manager mgcp
no ccm-manager fax protocol cisco
ccm-manager music-on-hold
ccm-manager config server ATD-CCM1
ccm-manager config
mgcp
mgcp call-agent 10.10.10.100 service-type mgcp version 0.1
mgcp dtmf-relay voip codec all mode out-of-band
mgcp rtp unreachable timeout 1000 action notify
mgcp modem passthrough voip mode nse
mgcp modem passthrough voip redundancy
mgcp package-capability rtp-package
mgcp package-capability sst-package
mgcp package-capability pre-package
mgcp default-package fxr-package
no mgcp package-capability res-package
no mgcp timer receive-rtcp
mgcp sdp simple
mgcp fax t38 inhibit
no mgcp explicit hookstate
mgcp rtp payload-type g726r16 static
mgcp bind control source-interface GigabitEthernet0/0
mgcp bind media source-interface GigabitEthernet0/0
mgcp profile default
dial-peer voice 999101 pots
service mgcpapp
port 1/0/1
forward-digits all
dial-peer voice 999102 pots
service mgcpapp
port 1/0/2
forward-digits all
dial-peer voice 999103 pots
service mgcpapp
port 1/0/3
forward-digits all
dial-peer voice 1 pots
service mgcpapp
incoming called-number .
direct-inward-dial
port 1/1/0:15
forward-digits all
dial-peer voice 999100 pots
service mgcpapp
port 1/0/0
gateway
timer receive-rtp 1200
scheduler allocate 20000 1000
ntp clock-period 17180351
ntp update-calendar
ntp server 10.10.10.9 source GigabitEthernet0/0
end
#sh controller e1
E1 1/1/0 is up.
Applique type is Channelized E1 - balanced
No alarms detected.
alarm-trigger is not set
Version info Firmware: 20090113, FPGA: 20, spm_count = 0
Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
Current port master clock:recovered from backplane
Data in current interval (225 seconds elapsed):
0 Line Code Violations, 0 Path Code Violations
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
Total Data (last 3 15 minute intervals):
0 Line Code Violations, 0 Path Code Violations,
0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins,
0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs
#sh ccm-manager
MGCP Domain Name: ATD-CCM-GW.xx.xxxx.xxx
Priority Status Host
============================================================
Primary Registered 10.10.10.100
First Backup None
Second Backup None
Current active Call Manager: 10.10.10.100
Backhaul/Redundant link port: 2428
Failover Interval: 30 seconds
Keepalive Interval: 15 seconds
Last keepalive sent: 15:31:24 UTC Oct 19 2012 (elapsed time: 00:00:09)
Last MGCP traffic time: 15:31:24 UTC Oct 19 2012 (elapsed time: 00:00:09)
Last failover time: None
Last switchback time: None
Switchback mode: Graceful
MGCP Fallback mode: Enabled/OFF
Last MGCP Fallback start time: None
Last MGCP Fallback end time: None
MGCP Download Tones: Disabled
TFTP retry count to shut Ports: 2
Backhaul Link info:
Link Protocol: TCP
Remote Port Number: 2428
Remote IP Address: 10.10.10.100
Current Link State: OPEN
Statistics:
Packets recvd: 11
Recv failures: 0
Packets xmitted: 18
Xmit failures: 0
PRI Ports being backhauled:
Slot 1, VIC 1, port 0
Configuration Auto-Download Information
=======================================
Current version-id: 1350042385-8bfc9ed0-f85e-4435-8baf-3ad1ceefb55c
Last config-downloaded:00:00:00
Current state: Waiting for commands
Configuration Download statistics:
Download Attempted : 1
Download Successful : 1
Download Failed : 0
TFTP Download Failed : 0
Configuration Attempted : 1
Configuration Successful : 1
Configuration Failed(Parsing): 0
Configuration Failed(config) : 0
Last config download command: New Registration
Configuration Error History:
controller E1 1/1/0
no pri-group timeslots 1-31
FAX mode: disable
#debug isdn q931
#debug mgcp packet
009112: Oct 20 12:48:50.374: MGCP Packet received from 10.10.10.100:2427--->
CRCX 2359 S1/SU1/DS1-0/[email protected] MGCP 0.1
C: D000000001fbf9aa000000F500000001
X: 1f
L: p:20, a:PCMU, s:off, t:00
M: recvonly
R: D/[0-9ABCD*#]
Q: process,loop
<---
009113: Oct 20 12:48:50.382: MGCP Packet sent to 10.10.10.100:2427--->
200 2359 OK
I: 8
v=0
c=IN IP4 10.10.10.254
m=audio 18274 RTP/AVP 0 100
a=rtpmap:100 X-NSE/8000
a=fmtp:100 192-194
<---
009114: Oct 20 12:48:50.386: ISDN Se1/1/0:15 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x4636A628 datasize = 64
009115: Oct 20 12:48:50.386: ISDN Se1/1/0:15 Q931d: data =
009116: Oct 20 12:48:50.386: 4636A628000000030240043800010000
009117: Oct 20 12:48:50.386: 0802000105A104038090A31803A9839F
009118: Oct 20 12:48:50.386: 280B526F6C616E64202D2049546C0601
009119: Oct 20 12:48:50.386: 81313232307009803636393332313933
009120: Oct 20 12:48:50.386:
009121: Oct 20 12:48:50.434: MGCP Packet received from 10.10.10.100:2427--->
MDCX 2360 S1/SU1/DS1-0/[email protected] MGCP 0.1
C: D000000001fbf9aa000000F500000001
I: 8
X: 1f
L: p:20, a:PCMU, s:off, t:b8, fxr/fx:t38
M: recvonly
R: D/[0-9ABCD*#]
Q: process,loop
<---
009122: Oct 20 12:48:50.438: MGCP Packet sent to 10.10.10.100:2427--->
510 2360 fx: setting cannot be supported
<---
009123: Oct 20 12:48:50.438: ISDN Se1/1/0:15 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x4636A628 datasize = 25
009124: Oct 20 12:48:50.438: ISDN Se1/1/0:15 Q931d: data =
009125: Oct 20 12:48:50.438: 4636A628000000030240043800010000
009126: Oct 20 12:48:50.438: 0802000145080280AF
009127: Oct 20 12:48:50.462: MGCP Packet received from 10.10.10.100:2427--->
DLCX 2361 S1/SU1/DS1-0/[email protected] MGCP 0.1
C: D000000001fbf9aa000000F500000001
I: 8
X: 1f
S:
<---
ATD-CCM-GW#
009128: Oct 20 12:48:50.478: MGCP Packet sent to 10.10.10.100:2427--->
250 2361 OK
P: PS=0, OS=0, PR=0, OR=0, PL=0, JI=0, LA=0
<---
009129: Oct 20 12:48:50.478: ISDN Se1/1/0:15 Q931d: srl_send_l3_pak:
source_id = CCM MANAGER 0x0003, dest_id = Q.921 0x0000, prim = DL_DATA_REQ 0x0240
priv_len = 4 int_id = 0x4636A628 datasize = 21
009130: Oct 20 12:48:50.478: ISDN Se1/1/0:15 Q931d: data =
009131: Oct 20 12:48:50.478: 4636A628000000030240043800010000
009132: Oct 20 12:48:50.478: 080200015A
ATD-CCM-GW#
009133: Oct 20 12:49:03.002: MGCP Packet received from 10.10.10.100:2427--->
CRCX 2362 S1/SU1/DS1-0/[email protected] MGCP 0.1
C: D000000001fbf9ac000000F500000002
X: 1e
L: p:20, a:PCMU, s:off, t:b8, fxr/fx:t38
M: recvonly
R: D/[0-9ABCD*#]
Q: process,loop
<---
#sh mgcp statistics
UDP pkts rx 270, tx 270
Unrecognized rx pkts 0, MGCP message parsing errors 0
Duplicate MGCP ack tx 0, Invalid versions count 0
CreateConn rx 10, successful 1, failed 9
DeleteConn rx 1, successful 1, failed 0
ModifyConn rx 1, successful 0, failed 1
DeleteConn tx 0, successful 0, failed 0
NotifyRequest rx 0, successful 0, failed 0
AuditConnection rx 0, successful 0, failed 0
AuditEndpoint rx 61, successful 61, failed 0
RestartInProgress tx 4, successful 4, failed 0
Notify tx 193, successful 193, failed 0
ACK tx 63, NACK tx 10
ACK rx 197, NACK rx 0
IP address based Call Agents statistics:
IP address 10.10.10.100, Total msg rx 270,
successful 260, failed 10
System resource check is DISABLED. No available statistic
DS0 Resource Statistics
Utilization: 0.00 percent
Total channels: 34
Addressable channels: 34
Inuse channels: 0
Disabled channels: 0
Free channels: 34
sh controller e1
#sh network-clocks
Network Clock Configuration
Priority Clock Source Clock State Clock Type
1 E1 1/1/0 GOOD E1
10 Backplane GOOD PLL
Current Primary Clock Source
Priority Clock Source Clock State Clock Type
1 E1 1/1/0 GOOD E1
Thanks for your helpThe explanation for your syslog message is " The B-channel indicated by this alarm has gone out of service. Some of the more common reasons for a B-channel to go out of service include: Taking the channel out of service intentionally to perform maintenance on either the near- or far-end; MGCP gateway returns an error code 501 or 510 for a MGCP command sent from Cisco Unified Communications Manager (Unified CM); MGCP gateway doesn't respond to an MGCP command sent by Unified CM three times; a speed and duplex mismatch exists on the Ethernet port between Unified CM and the MGCP gateway"
Recommended action:
Check the Unified CM advanced service parameter, Change B-channel Maintenance Status to determine if the B-channel has been taken out of service intentionally; Check the Q.931 trace for PRI SERVICE message to determine whether a PSTN provider has taken the B-channel out of service; Reset the MGCP gateway; Check the speed and duplex settings on the Ethernet port. -
File to File scenario using Transport Protocol FTP Problem
Hi,
my scenario is a file to file scenario using Transport Protocol FTP
there are 3 systems involved
a. computer 1 ( My system-source)
b. computer 2 (XI server)
c. computer 3 (Target system)
I want XI to pick file from computer 1 and post it to computer 3
I am logging on to XI server from computer 1(thro SAP GUI),
<u><b>Sender communication channel :</b></u>
Transport protocol:FTP
Messsage protocol: file
<u><b>In FTP connection Parameters:</b></u>
Server: computer 1 IP address
port:21
User name and PW---> I have given computer 1 Username and password.
Connection mode: permanently
Transfer mode: Binary
Folder: C:\ftproot\output
filename : given
<u><b>In Receiver Communication Channel</b></u>
Transport protocol:FTP
Message protocol: file
<u><b>In FTP connection Parameters:</b></u>
Server: computer 3 IP address
port:21
User name and PW---> I have given computer 3 Username and password.
Connection mode: permanently
Transfer mode: Binary
Put File: Use Temporary File
Folder:
eccserver\saploc\tmp
filename scheme: given
When I activate the scenario file is not getting picked from the source
In Adapter Framework: Message says up and running No message processing now
How to check FTP server is up and running on computer 1 (source system)and Computer 2 (XI server)?
What could be the problem ?
Thanks
dushanthHi
Consider that I dont have FTP installed on my computer. According to this blog
/people/shabarish.vijayakumar/blog/2006/08/01/along-came-a-file-adapter-mr-ftp-and-rest-of-the-gang
I have configured.
In sender comm channel I have given Ipaddress of computer 1 (which has a file to be picked)
In Receiver Comm channel I have given IP address of computer 3 (in which file to be posted)
and computer 2 is the XI server
Computer 1 has FTP installed
1. XI server should have FTP installed or not ? IF yes is it FTP client or FTP server or Guild FTP (according to the blog is enough)
2. Computer 3 should have FTP installed or not ?
Please help me I am really confused.
Thanks
dushanth -
What is the transport protocol File (Axis) in the SOAP Adapter
Hi,
for a SOAP Receiver Adapter it's possible to choose 'File (Axis)' as transport protocol.
How does it work and is there some documentation about it?
Thanks and regards
PatrickHi,
thanks for your answers.
@Prateek
Yes I tried -> Doesn't say so much
@Vinod
The first thread didn't helped me and I have seen already the second one.
@kummari
The question is how can I use it?
@Gabriel
>The adapter uses transport protocol(File (Axis)) to send SOAP messages as text file
Could you please explain it a little more detailed (maybe with an example)?
My question is about in which scenarios it makes sense to use this transport protocol and how is it used?
Thanks and regards
Patrick -
Fatal two-task communication protocol error (when using db link)
I have created the db link betwen two databases of oracle version 9i 9.0.2
the db link connects to specific user
when i access the table with same name as user then recieve following message
ORA-03106: fatal two-task communication protocol error
when i access the other tables having different name that the user to which the db link connects
that works alright
so what is solution of problem in this particular case?What is your Oracle release? Is it 9.0.1.2 or 9.2.0?
What version of Sql*Plus client are you using? -
ORA-27023: skgfqsbi: media manager protocol error
can some one please tell me what to do regarding this error, and how can i solve it. the result log is stated below...
Recovery Manager: Release 10.2.0.1.0 - Production on Tue Oct 16 15:26:49 2007
Copyright (c) 1982, 2005, Oracle. All rights reserved.
RMAN>
connected to target database: MOT (DBID=2759813257)
using target database control file instead of recovery catalog
RMAN>
echo set on
RMAN> run {
2> allocate channel oem_sbt_backup type 'sbt_tape' format '%U';
3> backup as BACKUPSET current controlfile tag '10162007032648';
4> restore controlfile validate from tag '10162007032648';
5> release channel oem_sbt_backup;
6> }
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03009: failure of allocate command on oem_sbt_backup channel at 10/16/2007 15:26:50
ORA-19554: error allocating device, device type: SBT_TAPE, device name:
ORA-27023: skgfqsbi: media manager protocol error
ORA-19511: Error received from media manager layer, error text:
sbt__rpc_connect: Internal error - could not connect to obproxyd (Oracle Secure Backup error: 'bad port name specified (OB SBT proxy manager)').
RMAN> allocate channel for maintenance type 'sbt_tape' ;
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03009: failure of allocate command on ORA_MAINT_SBT_TAPE_1 channel at 10/16/2007 15:26:51
ORA-19554: error allocating device, device type: SBT_TAPE, device name:
ORA-27023: skgfqsbi: media manager protocol error
ORA-19511: Error received from media manager layer, error text:
sbt__rpc_connect: Internal error - could not connect to obproxyd (Oracle Secure Backup error: 'bad port name specified (OB SBT proxy manager)').
RMAN> delete noprompt backuppiece tag '10162007032648';
allocated channel: ORA_DISK_1
channel ORA_DISK_1: sid=125 devtype=DISK
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of delete command at 10/16/2007 15:26:51
RMAN-06168: no backup pieces with this tag found: 10162007032648
RMAN> exit;
Recovery Manager complete.can some one please tell me what to do regarding this error, and how can i solve it. the result log is stated below...
Recovery Manager: Release 10.2.0.1.0 - Production on Tue Oct 16 15:26:49 2007
Copyright (c) 1982, 2005, Oracle. All rights reserved.
RMAN>
connected to target database: MOT (DBID=2759813257)
using target database control file instead of recovery catalog
RMAN>
echo set on
RMAN> run {
2> allocate channel oem_sbt_backup type 'sbt_tape' format '%U';
3> backup as BACKUPSET current controlfile tag '10162007032648';
4> restore controlfile validate from tag '10162007032648';
5> release channel oem_sbt_backup;
6> }
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03009: failure of allocate command on oem_sbt_backup channel at 10/16/2007 15:26:50
ORA-19554: error allocating device, device type: SBT_TAPE, device name:
ORA-27023: skgfqsbi: media manager protocol error
ORA-19511: Error received from media manager layer, error text:
sbt__rpc_connect: Internal error - could not connect to obproxyd (Oracle Secure Backup error: 'bad port name specified (OB SBT proxy manager)').
RMAN> allocate channel for maintenance type 'sbt_tape' ;
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03009: failure of allocate command on ORA_MAINT_SBT_TAPE_1 channel at 10/16/2007 15:26:51
ORA-19554: error allocating device, device type: SBT_TAPE, device name:
ORA-27023: skgfqsbi: media manager protocol error
ORA-19511: Error received from media manager layer, error text:
sbt__rpc_connect: Internal error - could not connect to obproxyd (Oracle Secure Backup error: 'bad port name specified (OB SBT proxy manager)').
RMAN> delete noprompt backuppiece tag '10162007032648';
allocated channel: ORA_DISK_1
channel ORA_DISK_1: sid=125 devtype=DISK
RMAN-00571: ===========================================================
RMAN-00569: =============== ERROR MESSAGE STACK FOLLOWS ===============
RMAN-00571: ===========================================================
RMAN-03002: failure of delete command at 10/16/2007 15:26:51
RMAN-06168: no backup pieces with this tag found: 10162007032648
RMAN> exit;
Recovery Manager complete. -
Important!!! ldap_rename_s: Protocol error with ldapmoddn
When I use "ldapmoddn" to move a user in Active Directory, I have the error:
"ldap_rename_s: Protocol error
ldap_rename_s: additional info: 00000057: LdapErr: DSID-0C09080A, comment: Error in attribute conversion operation, data 0, v893"
And the command line is:
ldapmoddn -p 389 -h 190.57.160.24 -D "CN=administrateur,CN=USERS,DC=xxx,DC=org" -w taaze -b "CN=a,OU=test,dc=xxx,dc=org" -N "dc=xxx,dc=org"
But the user have minimum information...
It's very important for me because it's for my training periode to validate my master!!
Thanks you very much...If I use only the -N option without -R option
ex:ldapmoddn -p 389 -h 190.57.160.24 -D "CN=administrateur,CN=USERS,DC=xxx,DC=org" -w xxx -b "CN=a,OU=test,dc=xxx,dc=org" -N "dc=xxx,dc=org"
I have this error:
"ldap_rename_s: Protocol error
ldap_rename_s: additional info: 00000057: LdapErr: DSID-0C09080A, comment: Error in attribute conversion operation, data 0, v893"
Can you help me please?????
Matthieu -
TT12241: Backup stream protocol error
Hi there,
I get the following error when replicating TT 6.04 datastore:
$ /data/TimesTen/6.04/bin/ttRepAdmin -duplicate -from UsageCollector -host NODE_B -setMasterRepStart -delXla -localhost NODE_A UsageCollector
TT12241: Backup stream protocol error: bad log data packet length -- file "restore.c", lineno 2865, procedure "restoreLogFileNS"
Unfortunately this error, TT12241, is not described in the documentation. Oracle Support and Google searches don’t return any relevant information.
Have any one came across this problem before?
Thanks,
IgorI can't find any previous SR reports of the TT12241. No probable candidate bugs are returned either. However I have not seen the -delXla option being used before, so it may have something to do with using this option. Are you able to exclude this option from the ttRepAdmin -duplicate, and allow the bookmarks to be copied over? You could then connect to the newly created datastore and try to manually delete the bookmarks using "xladeletebookmark".
-
Hi All,
Here is the scenario. Trading Partner (TP) A is sending a RosettaNet business
message (PIP3A2) to TP B. When the weblogic Integration server for TP B receives
this message, I get the following error message,
####<Dec 4, 2001 4:00:33 PM PST> <Error> <B2B> <erpsystem> <myserver> <ExecuteThread:
'9' for queue: 'default'> <> <19:c285badb981bb8b8> <000000> <<RN-Protocol> ERROR:
Cannot locate CA for URI http://localhost:7001/Quantum, Business Identifier 987654321,
Role Product Supplier, in Coversation 3A2, version 1.3.>
It is referring to Conversation 3A2 eventough it has been deleted and should be
using the Conversation called PIP3A2. Can anyone tell me where and how this conversation
is referenced and how it can be fixed?
--Krish.Hi All,
Here is the scenario. Trading Partner (TP) A is sending a RosettaNet business
message (PIP3A2) to TP B. When the weblogic Integration server for TP B receives
this message, I get the following error message,
####<Dec 4, 2001 4:00:33 PM PST> <Error> <B2B> <erpsystem> <myserver> <ExecuteThread:
'9' for queue: 'default'> <> <19:c285badb981bb8b8> <000000> <<RN-Protocol> ERROR:
Cannot locate CA for URI http://localhost:7001/Quantum, Business Identifier 987654321,
Role Product Supplier, in Coversation 3A2, version 1.3.>
It is referring to Conversation 3A2 eventough it has been deleted and should be
using the Conversation called PIP3A2. Can anyone tell me where and how this conversation
is referenced and how it can be fixed?
--Krish. -
I'm currently upgrading from Weblogic 8.1 to Weblogic 9.1 on a Windows environment (Windows XP on my dev box) with an Oracle 8.1.6 database.
During the upgrade, we switched from BEA's Oracle OCI driver ( weblogic.jdbc.oci.Driver ) in Weblogic 8.1 to their Type 4 JDBC driver in Weblogic 9.1 which resulted in a "Net8 protocol error".
Does anybody know what's causing this error and how to resolve this?
Thanks
Stack trace:
####<16-Jun-2006 9:37:35 o'clock AM PDT> <Error> <HTTP> <HY119402> <HY119402.CM-Fleet-Admin> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1150475855789> <BEA-101020> <[weblogic.servlet.internal.WebAppServletContext@681e45 - name: 'CMWeb', context-path: '/CMWeb'] Servlet failed with Exception
com.abs.cmweb.main.MainRuntimeException: CMWeb: INTERNAL RUNTIME EXCEPTION: EJB Exception: ; nested exception is:
com.westech.jade.service.entity.EntityRuntimeException: INTERNAL RUNTIME EXCEPTION: INTERNAL RUNTIME EXCEPTION: <b>[BEA][Oracle JDBC Driver]Internal error: Net8 protocol error.SQL Failed</b>: SELECT OID, BOUNDARY_NAME, USER_ID, PREFERENCE_VALUE FROM CMWEB_BOUNDARY_PREFERENCE WHERE BOUNDARY_NAME = ? AND USER_ID = ?
at com.abs.cmweb.main.control.boundaryUserPreferenceController.BoundaryUserPreferenceControllerRIProxy.findBoundaryUserPreference(BoundaryUserPreferenceControllerRIProxy.java:148)
at com.abs.cmweb.main.util.boundaryUserPreferenceHelper.BoundaryUserPreferenceHelper.getBoundaryUserPreference(BoundaryUserPreferenceHelper.java:50)
at com.abs.cmweb.waterConveyance.boundary.viewingWCInstructionsAndImplementations.ViewingWCInstructionsAndImplementationsUseBean.applyUserPreference(ViewingWCInstructionsAndImplementationsUseBean.java:275)
at com.abs.cmweb.waterConveyance.boundary.viewingWCInstructionsAndImplementations.ViewingWCInstructionsAndImplementationsUseBean.processBoundaryEvent(ViewingWCInstructionsAndImplementationsUseBean.java:179)
at com.abs.cmweb.waterConveyance.boundary.viewingWCInstructionsAndImplementations.ViewingWCInstructionsAndImplementationsFromHomeUseBean.processBoundaryEvent(ViewingWCInstructionsAndImplementationsFromHomeUseBean.java:32)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.fireEvent(HtmlBoundaryController.java:1303)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processHtmlBoundaryAction(HtmlBoundaryController.java:337)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processHttpServletRequest(HtmlBoundaryController.java:255)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processRequestResponse(HtmlBoundaryController.java:152)
at jsp_servlet._waterconveyance._viewingwchome.__viewingwchome._jspService(__viewingwchome.java:329)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:225)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:127)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:272)
at weblogic.servlet.internal.ServletStubImpl.onAddToMapException(ServletStubImpl.java:380)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:298)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:165)
at weblogic.servlet.internal.RequestDispatcherImpl.invokeServlet(RequestDispatcherImpl.java:496)
at weblogic.servlet.internal.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:245)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.doForward(HtmlBoundaryController.java:833)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.doForward(HtmlBoundaryController.java:966)
at com.abs.cmweb.main.boundary.navigatingCMWeb.NavigatingCMWebUseBean.doRedirectToBoundary(NavigatingCMWebUseBean.java:290)
at com.abs.cmweb.main.boundary.navigatingCMWeb.NavigatingCMWebUseBean.processBoundaryEvent(NavigatingCMWebUseBean.java:234)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.fireEvent(HtmlBoundaryController.java:1303)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processHtmlBoundaryAction(HtmlBoundaryController.java:337)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processHttpServletRequest(HtmlBoundaryController.java:255)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processRequestResponse(HtmlBoundaryController.java:152)
at jsp_servlet._main._viewingcmwebhome.__navigatingcmweb._jspService(__navigatingcmweb.java:470)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:225)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:127)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:272)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:165)
at weblogic.servlet.internal.RequestDispatcherImpl.invokeServlet(RequestDispatcherImpl.java:496)
at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispatcherImpl.java:426)
at weblogic.servlet.jsp.PageContextImpl.include(PageContextImpl.java:152)
at jsp_servlet._main._viewingapplicationmessages.__viewingapplicationmessages._jspService(__viewingapplicationmessages.java:298)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:225)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:127)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:272)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:165)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3153)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:1973)
at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:1880)
at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1310)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:207)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:179)Doug Chew wrote:
I'm currently upgrading from Weblogic 8.1 to Weblogic 9.1 on a Windows environment (Windows XP on my dev box) with an Oracle 8.1.6 database.
During the upgrade, we switched from BEA's Oracle OCI driver ( weblogic.jdbc.oci.Driver ) in Weblogic 8.1 to their Type 4 JDBC driver in Weblogic 9.1 which resulted in a "Net8 protocol error".
Does anybody know what's causing this error and how to resolve this?
ThanksHi, yes. Our old, deprecated and now removed type-2 driver used OCI (whatever version
you have installed) to talk to Oracle. Our new drivers use the wire-level protocol for
all supported DBMS versions. Oracle 8.1.6 is extremely old. I don't think it's even
supported by Oracle anymore, is it? I think you have two options:
1 - Try using Oracle's driver, in the type-2 mode so it also uses OCI.
2 - If (1) doesn't work, you probably have to upgrade your DBMS.
Joe
>
>
Stack trace:
####<16-Jun-2006 9:37:35 o'clock AM PDT> <Error> <HTTP> <HY119402> <HY119402.CM-Fleet-Admin> <[ACTIVE] ExecuteThread: '0' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1150475855789> <BEA-101020> <[weblogic.servlet.internal.WebAppServletContext@681e45 - name: 'CMWeb', context-path: '/CMWeb'] Servlet failed with Exception
com.abs.cmweb.main.MainRuntimeException: CMWeb: INTERNAL RUNTIME EXCEPTION: EJB Exception: ; nested exception is:
com.westech.jade.service.entity.EntityRuntimeException: INTERNAL RUNTIME EXCEPTION: INTERNAL RUNTIME EXCEPTION: <b>[BEA][Oracle JDBC Driver]Internal error: Net8 protocol error.SQL Failed</b>: SELECT OID, BOUNDARY_NAME, USER_ID, PREFERENCE_VALUE FROM CMWEB_BOUNDARY_PREFERENCE WHERE BOUNDARY_NAME = ? AND USER_ID = ?
at com.abs.cmweb.main.control.boundaryUserPreferenceController.BoundaryUserPreferenceControllerRIProxy.findBoundaryUserPreference(BoundaryUserPreferenceControllerRIProxy.java:148)
at com.abs.cmweb.main.util.boundaryUserPreferenceHelper.BoundaryUserPreferenceHelper.getBoundaryUserPreference(BoundaryUserPreferenceHelper.java:50)
at com.abs.cmweb.waterConveyance.boundary.viewingWCInstructionsAndImplementations.ViewingWCInstructionsAndImplementationsUseBean.applyUserPreference(ViewingWCInstructionsAndImplementationsUseBean.java:275)
at com.abs.cmweb.waterConveyance.boundary.viewingWCInstructionsAndImplementations.ViewingWCInstructionsAndImplementationsUseBean.processBoundaryEvent(ViewingWCInstructionsAndImplementationsUseBean.java:179)
at com.abs.cmweb.waterConveyance.boundary.viewingWCInstructionsAndImplementations.ViewingWCInstructionsAndImplementationsFromHomeUseBean.processBoundaryEvent(ViewingWCInstructionsAndImplementationsFromHomeUseBean.java:32)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.fireEvent(HtmlBoundaryController.java:1303)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processHtmlBoundaryAction(HtmlBoundaryController.java:337)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processHttpServletRequest(HtmlBoundaryController.java:255)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processRequestResponse(HtmlBoundaryController.java:152)
at jsp_servlet._waterconveyance._viewingwchome.__viewingwchome._jspService(__viewingwchome.java:329)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:225)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:127)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:272)
at weblogic.servlet.internal.ServletStubImpl.onAddToMapException(ServletStubImpl.java:380)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:298)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:165)
at weblogic.servlet.internal.RequestDispatcherImpl.invokeServlet(RequestDispatcherImpl.java:496)
at weblogic.servlet.internal.RequestDispatcherImpl.forward(RequestDispatcherImpl.java:245)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.doForward(HtmlBoundaryController.java:833)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.doForward(HtmlBoundaryController.java:966)
at com.abs.cmweb.main.boundary.navigatingCMWeb.NavigatingCMWebUseBean.doRedirectToBoundary(NavigatingCMWebUseBean.java:290)
at com.abs.cmweb.main.boundary.navigatingCMWeb.NavigatingCMWebUseBean.processBoundaryEvent(NavigatingCMWebUseBean.java:234)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.fireEvent(HtmlBoundaryController.java:1303)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processHtmlBoundaryAction(HtmlBoundaryController.java:337)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processHttpServletRequest(HtmlBoundaryController.java:255)
at com.westech.jade.service.boundary.html.HtmlBoundaryController.processRequestResponse(HtmlBoundaryController.java:152)
at jsp_servlet._main._viewingcmwebhome.__navigatingcmweb._jspService(__navigatingcmweb.java:470)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:225)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:127)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:272)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:165)
at weblogic.servlet.internal.RequestDispatcherImpl.invokeServlet(RequestDispatcherImpl.java:496)
at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispatcherImpl.java:426)
at weblogic.servlet.jsp.PageContextImpl.include(PageContextImpl.java:152)
at jsp_servlet._main._viewingapplicationmessages.__viewingapplicationmessages._jspService(__viewingapplicationmessages.java:298)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:34)
at weblogic.servlet.internal.StubSecurityHelper$ServletServiceAction.run(StubSecurityHelper.java:225)
at weblogic.servlet.internal.StubSecurityHelper.invokeServlet(StubSecurityHelper.java:127)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:272)
at weblogic.servlet.internal.ServletStubImpl.execute(ServletStubImpl.java:165)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:3153)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
at weblogic.servlet.internal.WebAppServletContext.securedExecute(WebAppServletContext.java:1973)
at weblogic.servlet.internal.WebAppServletContext.execute(WebAppServletContext.java:1880)
at weblogic.servlet.internal.ServletRequestImpl.run(ServletRequestImpl.java:1310)
at weblogic.work.ExecuteThread.execute(ExecuteThread.java:207)
at weblogic.work.ExecuteThread.run(ExecuteThread.java:179) -
SIR,
i hadbeen installed oracle aplication server.but i m not connecting to database.when i use the sql*plus.i use the user name-scott &password-tiger.i got an error ORA-12560=TNS PROTOCOL ERROR.
I M NOT ABLE TO RECTIFY ITS PROBLEM,how can i create host string in oracle application server 10g.please send reply its very urgent.
thanx ranjeetAlthough this question is completely off topic of the Personalization you can learn how to configure the SQL*Net connect from the manual by reading the topic "Configure the Client to Use a Net Service Name" found at the following link:
http://download-west.oracle.com/docs/cd/A91202_01/901_doc/network.901/a90154/gettings.htm#483215
Maybe you are looking for
-
My earphone that came with the ipod touch is not working
the earphone that came with the ipod is not workin, the microfone doesnt work, and the volume control doesnt too, but, the stop/play button works, and the overall sound from the phone, wat is happening? can smeone help me?
-
Itunes won't recognize my balance from a purchased gift card so I cannot buy any new songs
itunes won't recognize my balance from a gift card & won't let me purchase anything from the itunes store. How do I fix this?
-
JCA: Sample Adapter Transaction Support
Hi guys, Could anyone tell me the transaction level supported by Sample Adapter.In the code they are using SAPResourceAdapter to access the J2EE Thread Manager.But in the code it has given that it won't support Local Transaction or XA Resource. S
-
Recognize Font Substitution has taken place
Is there a way using the Illustrator API that I can tell if substituted fonts exist in a document after it is loaded.
-
Query Builder - Path and Object name for instance ..
Hello, how to get the Object Name of an Instance "InstanceX" and the Path of the Object with query Builder .. Thanks