Trash icon not changing when full

The trash icon isn't changing to appear full when I have things in it. How do I change it back to normal?

I would try to relaunch finder from the force quit menu. Apple Logo > Force Quit.
If that doesn't resolve it, I would delete the finder plist in mac hd/users/username/library/preferences.
Let me know if that helps.
Thanks,
Kevin

Similar Messages

  • Trash Icon Not Changing, Can Only Empty Using Terminal

    I did a ful wipe & load with Mavericks, and since day one, the Trash icon doesn't change when files go in. If I right click, all I can do is Open and see the files there. The only way I can empty the Trash is by using this command in Terminal: rm -rf ~/.Trash/*
    Files are definitely there, I can see them if I open the Trash. Any ideas?

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, or by corruption of certain system caches. 
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled on some models, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including sound output and  Wi-Fi on certain models. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin. Test while in safe mode. Same problem? After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of the test.

  • TS2771 on i pod touch the orientation does not change when I turn it on it's side when using safari etc.  When viewing youtube it only displays widescreen and will not display portrait , anyone any ideas? is this a fault or do all ipod touch do this?

    On i pod touch the orientation does not change when I turn it on it's side when using safari etc.  When viewing youtube it only displays widescreen and will not display portrait , anyone any ideas? is this a fault or do all ipod touch do this?

    The user guide says:
    Movies viewed in Videos and YouTube appear only in landscape orientation. Street views in Maps
    also appear only in landscape orientation.
    Do you have the scree orientation lock turned on? If on there is a circular arrow icon with a padlock inside next to the battery charge icon in the upper right.

  • View only works in one direction,will not change when I turn the phone

    view only works in one direction,will not change when I turn the phone

    Is the rotate lock on?
    http://appletoolbox.com/2013/03/iphone-ipad-or-ipod-screen-will-not-rotate-fix/

  • Visited link color is not changing when there is no page redirection

    Visited link color is not changing when i just open a popup on clicking the hyperlink.. whereas visited link color gets changed when i redirect to a new page on clicking the hyperlink
    I want to have my visited link color to change even if i show a popup on clicking the hyperlink
    This works fine with IE..

    Hi,
    Have a look at the user status table TSOCM_STAT_PROP and see if there are any unwanted PROCESS_TYPE <> STSMA combinations.
    For your process type there should only be one kind of status schema assigned.

  • Colors in parade do not change when I move the Temperature slider.

    I am trying to do the speed grade tutorial, but the color does not change when I move the temperature slider.

    It might be nice to know which "issue" of Sg you're using.There have been issues where the colors "lag" while using a slider/control, but typically when you let "up" on the control, the adjustment is "there". From your comment, am I correct in assuming that the controls simply don't do anything even after you've moved them? And of course ... when you "move" them, you do see the indicator on the slider-line move, right?
    Neil

  • The display on my iPhone only works vertically.  It will not change when I rotate my phone.

    The display on my iPhone only works vertically.  It will not change when I rotate my phone.

    Swipe up on the bottom of the screen to expose control center and see if the orientation lock is on (top row of controls, far right; looks like a lock with a circular arrow).
    Not all apps support orientation changes, BTW.

  • Look for a progarm that will let me have 2 moniters but one will lock on and will not change when using spaces

    look for a progarm that will let me have 2 moniters but one will lock on and will not change when using spaces

    ok so i have one moniter to the right of me and i want to keep my google chrome on that one but still be abel to use space on the many monter. cuz when you go to spaces it movies both moniter i hope that help and i hope that you can help me.

  • How do I check internet usage history? When i use the "History" tab on the tool bar all I see is today's activity & the calendar does not change when I click on it. Thanks

    How do I check internet usage history? When i use the "History" tab on the tool bar all I see is today's activity & the calendar does not change when I click on it. Thanks

    zedzed,
    Here's another thought.
    Navigate to HD > Users > Library > Safari: Make a duplicate of History.plist.
    To duplicate the file, click once to highlight it. Press the Command + D keys.
    Drag the History,plist copy file to the Desktop.
    Highlight it. Press the Command + I keys, to get info.
    Change Open With to TextEdit.
    When you open the file in TextEdit, it will be difficult to read, but you will be able to pick out some sites.
    ali b

  • Preview icon not showing when in thumbnail. (Sketchu

    Hello,
    I recently updated my MBP to Yosemite and installed sketchup on it.
    The preview icon of my sketchup files are not showing when in thumbnail. But as i increase the size of the icon from thumbnail in viewoption i.e from 64px x 64px to 124px x 124px it shows. So my icon is shown as blank without any app logo. Also when i change my view from thumbnail to coverflow or something it shows. Otherthan thumbnail everything works.
    So where is the error in it?
    Please help...
    Thanks
    Amar

    Try the standard fixes:
    - Rest. Nothing is lost
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears. - Restore from backup
    - Restore to factory defaults/new iPod.

  • Cursor does not change when hovering over pop-up window link

    I created a text link for a pop-up window. The link does work, but the cursor does not change to a pointy finger, the standard link icon.
    I don't know a lot of javascript, but can figure it out if it's just adding some code.This was done in CS3. Any help would be appreciated! Here's the code:
    function MM_openBrWindow(theURL,winName,features) { //v2.0
      window.open(theURL,winName,features);
    Thanks in advance.
    Todd

    A link would be nice but I suspect that you are not gettign the finger (you knwo what I mean) when you roll over the link because your href is  not set to anything.
    <a href="" onclick=MM_openBrWindow('images/image.jpg','largeDisplay','scrollbars=yes,resizable=yes,width=100,height=120')
    Set your href to "#" or "javascript:;" - the latter is preferred.

  • Safari 5.0 - URL does not change when changing location

    I have noticed this on two Macs running 10.6.3. When moving between pages (eg, clicking on a link within a page, or using the Google search bar to locate and load a new page), the URL in the address bar does not change to the new location. It remains at the
    This applies whether the new page is within the same domain, or is at a different location.
    Specific test: Load http://news.bbc.co.uk in Safari. Towards the top left of the page, there's a link to the BBC home page, which should appear in the status bar as "http://www.bbc.co.uk". Clicking on it will send you to that page, but the URL will remain as the news subdomain. If you click to another tab, then click back, it'll then update correctly.
    Matt

    Hi Matt,
    MIght be corrupted Safari pref files.
    Go to the Safari Menu Bar, click Safari/Preferences. Make note of all the preferences under each tab. Quit Safari. Now go to ~/Library/Preferences and move this file com.apple.safari.plist to the Desktop.
    Relaunch Safari and see if that makes a difference. If not, move the .plist file back to the Preferences folder. If Safari functions as it should, move that .plist file to the Trash.
    If the problem persists, go to ~/Library/Caches. From the com.apple.Safari folder move the "cache.db" file to the Trash. Relaunch Safari.
    Carolyn

  • Personalise value icon not available when query executed from portal

    Hi
    The personalise value icon is not available when the query is executed from the portal.
    Is this the norm or is there anything i must change?
    Regards
    Shalini

    Since you have not given us much information to go on, I will start with the basics...
    Have you activated the Personalization DSOs (0PERS_WTE, 0PERS_BOD & 0PERS_VAR)? 
    If not, you will need to do so in tcode SPRO (SAP Reference IMG --> SAP NetWeaver --> Business Intelligence --> Settings for Reporting and Analysis --> General Settings for Reporting and Analysis --> Activate Personalization in BEx)
    Are you running a BW 3.5 query or a BI 7.0 query?
    If BI 7.0, the way to set personalization values has changed. You have to open the personalization section of the variables refresh screen by clicking on "Show Personalization Values" at the top of the screen, then move the desired variables down to that section.
    Hope some of this helps...
    Bob

  • Creative Cloud Problem - Try Icons not changing to Download Icons

    I just purchased a Creative Could for Teams membership and my icons will not change from "Try" to "Download". I've installed the Adobe Application Manager and I've also logged out and logged back in several times and the icons still do not change. Can someone help?

    Hi David... thank you for your offer of help. Have come round to that view ourselves that the issue was possibly caused right at the start of our purchase. That's now 10 days gone by without access to the products and we are starting to wonder if it will ever be resolved.
    Incidentally could I ask? Is it the case that the software should be available simply by logging on with your ID and password to creative.adobe.com and then selecting "Apps"? When we log onto creative.adobe.com and click on "My Account" it only shows 2GB space available instead of 20GB and on the Plan Information tab it shows the "Free membership" option when we would presume it should show our purchase of Creative Cloud. We have checked with our bank and the payment for the CC subscription did process with the first payment made to Adobe on the date of purchase.
    The software presently installed on the workstation is Adobe Master Suite CS6 and is a high end spec HP Z800 (windows 7 pro service pack 1) if that helps in anyway. The Adobe Download Manager was installed previously as part of an update for our CS6 Master Suite package.
    If you can fix this for us you are on our Christmas card list lol.....
    Thanks
    Bill

  • Statistic report with figures that will not change when rerun months later

    Hi,
    Is there any good practices that we can follow to create statistic reports with figures that will not change even when rerun after few months later?
    My scenario is my statistic report is generated based on data that is "alive" which means the record will get change after a period of time. So, if you generate the statistic report in for January 2006 in the month of January and regenerate in May for the January 2006 statistic, the figure is different. But what I want is to be able to get the same figures.
    I know in this case looks like we need some sort of summary tables, so posting this to get advice on the best way to design such summary tables. Please comment if there is other ways of doing it.
    Summary tables may work for statistic report, but how to support detail report listing where the records are required to be the same when it was generated few months ago.
    Please advise.
    Thank you.

    What happens, when you execute a report today is the following: a select statement is fired at the data base and the result set is displayed in the report. The data can change after the moment you launched your report. What you could do to keep the result set the same, is implementing a user parameter that fills your date discriminator.

Maybe you are looking for