Travel Request not appearing in Manager's inbox

Hi,
We have done all the necessary configuration for Travel Request Apps in Fiori.
Employee successfully submits travel request for approval but it doesnt appear in managers inbox for approval.
Any idea what might be the issue here.
Thanks,
Sriram
Tags edited by: Michael Appleby

Hi Sriram,
Please test the scenario in the backend without Fiori. The scenario should be up and running.
SAP Fiori LL04 - Make sure the backend applications are running before implementation
Regards, Masa
SAP Customer Experience Group - CEG

Similar Messages

3702i AP's not Joining WLC - Layer 3 discovery request not received on management VLAN

Hi Guys,
This is a follow up post to this thread: https://supportforums.cisco.com/discussion/12400481/3702i-not-joint-2504
Have been playing around with my AP's and made sure the time is correct on all the devices ( WLC and Switch). I have also moved the AP's to the same Vlan as the management IP of the WLC.
if I move the AP's to the same Vlan as the WLC they join and are happy, as soon as I move them to a different Vlan they cant join and there time goes back to the default plus they do not seem to save the WLC details to flash but still remember the test names I give them.
it appears that option 43 is working fine as I can see it look for the WLC IP and I have done some trouble shooting on the WLC and it looks like it see's the AP but doesn't except it.
please see below for the boot up of the AP and the WLC logs:
AP
IIOS Bootloader - Starting system.
*** deleted for breverity *****
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
*** deleted for breverity *****
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
*** deleted for breverity *****
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
WLC:
isco Controller) >show time
Time............................................. Tue Jan 27 17:44:47 2015
Timezone delta................................... 0:0
Timezone location................................ (GMT +8:00) HongKong, Bejing, Chongquing
NTP Servers
NTP Polling Interval......................... 3600
   Index NTP Key Index NTP Server NTP Msg Auth Status
   1 0 150.101.176.226 AUTH DISABLED
(Cisco Controller) >show ap join stats summary
Incorrect input! Use 'show ap join stats summary [all/<ap-mac>]'
(Cisco Controller) >show ap join stats summary all
Number of APs.............................................. 2
Base Mac AP EthernetMac AP Name IP Address Status
f4:4e:05:aa:a6:a0 f4:4e:05:94:c3:98 APf44e.0594.c398 10.1.1.22 Joined
f4:4e:05:b6:ce:f0 N A Test_1 10.1.20.7 Not Joined
(Cisco Controller) >show ap join stats detailed f4:4e:05:b6:ce:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 45
- Successful discovery responses sent...................... 21
- Unsuccessful discovery request processing................ 24
- Reason for last unsuccessful discovery attempt........... Layer 3 discovery request not received on management VLAN
- Time at last successful discovery attempt................ Jan 27 17:45:49.705
- Time at last unsuccessful discovery attempt.............. Jan 27 17:45:49.705
Join phase statistics
- Join requests received................................... 0
- Successful join responses sent........................... 0
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Not applicable
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... Lwapp discovery request rejected
- Reason for error that occurred last...................... Layer 3 discovery request not received on management VLAN
- Time at which the last join error occurred............... Jan 27 17:45:49.705
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
   Ethernet Mac : 00:00:00:00:00:00 Ip Address : 10.1.20.7
(Cisco Controller) >show interface summary
Number of Interfaces.......................... 4
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
ap LAG 20 10.1.20.231 Dynamic No No
guest LAG 30 10.1.30.231 Dynamic No No
management LAG 10 10.1.1.231 Static Yes No
virtual N/A N/A 1.1.1.1 Static No No
SWITCH
witch#show run
Building configuration...
*** deleted for breverity *****
no aaa new-model
clock timezone AWST 8
system mtu routing 1500
ip routing
ip dhcp pool WAP_Pool
   network 10.1.20.0 255.255.255.0
   default-router 10.1.20.1
   option 43 hex f104.0a01.01e7
ip dhcp pool Clients
   network 10.1.30.0 255.255.255.0
   default-router 10.1.30.1
   dns-server 203.0.178.191
ip dhcp pool test
   network 10.1.1.0 255.255.255.0
   default-router 10.1.1.1
crypto pki trustpoint TP-self-signed-4082587776
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4082587776
revocation-check none
rsakeypair TP-self-signed-4082587776
*** deleted for breverity *****
*** deleted for breverity ***** !
interface FastEthernet0/3
description *** WLC ****
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/4
description **** AP *****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/5
description **** AP ****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/6
i*** deleted for breverity ***** !
interface Vlan10
description *** Managment ***
ip address 10.1.1.230 255.255.255.0
interface Vlan20
description *** WIRELESS APS ***
ip address 10.1.20.1 255.255.255.0
interface Vlan30
ip address 10.1.30.1 255.255.255.0
ip classless
ip route 0.0.0.0 0.0.0.0 10.1.1.1
ip http server
ip http secure-server
ip sla enable reaction-alerts
l*** deleted for breverity *****
ntp clock-period 36028827
ntp source FastEthernet0/1
ntp server 121.0.0.42
ntp server 202.127.210.37
end
I have also placed a Device in Vlan 20 and it is able to ping the WLC and the WLC can ping it s routing is working.
Thanks

Hey Scott,
I gave that a shot and still no luck, log's from AP boot up:
IIOS Bootloader - Starting system.
flash is writable
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 20 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 21 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 1 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
   cisco Systems, Inc.
   170 West Tasman Drive
   San Jose, California 95134-1706
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 67 files, 9 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 20894208
flashfs[2]: Bytes available: 20006400
flashfs[2]: flashfs fsck took 14 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)
POWER TABLE FILENAME = ram:/Q2.bin
Radio1 present 8864 8000 0 80000000 80100000 4
POWER TABLE FILENAME = ram:/Q5.bin
Radio2 not present 0 0 0 0 0 8
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP

I upgraded to iTunes 11.0. My iPod Nano 4th Version will sync, but music and playlists will not appear to manage and add more songs. Is there a fix?

I upgraded to iTunes 11.0. My iPod Nano 4th Version will sync, but music and playlists will not appear to manage and add more songs. Is there a fix?

If I go from 'Devices' to Summary and then Music, I only get one option-Sync Music,There is a box on this page but the options within it are grayed out. If I tick the Sync Music option I get this message-
'Are you sure you want to remove existing music,films,ect, from this ipod and sync with this itunes library?
'Music synced to (my ipods name) from other itunes libraries will be removed and items will be synced from this itunes library' I have only ever used itunes on this PC and the 'Manually manage music and videos' is ticked but
that must be a default setting as I haven't ticked it.

Forward button not appearing in the workflow inbox

Hi All,
We have an issue where a user says that the forward button is not appearing in the workflow inbox . This is happening only for one user. Is there an way through which we can add the forward button?
Regards
Archana

Hi Archana,
If Basis have confirmed that the user has the authorization, then the user should be able to forward tasks.
Right click on a task in the inbox, it should allow the user to forward the task.
If the user does not have the authorization, then a message will appear that user does not have authorization to forward tasks.
Immediately after that take a screen shot of SU53, which will show you why task forwarding is not possible.
Regards
Srinivas

Leave Request Not Appearing in UWL for Manager

Hi,
We have a strange issue where leave requests are not appearing in the UWL for a specific manager. We have checked with other managers and the leaves are appearing in their UWLs and they are able to process their employee's leaves without any issue.
For the manager not seeing the leave in their UWL, I have confirmed the following:
1) Proper manager defaults in 'approver' field in ESS and employee is able to send leave request without issue
2) Manager receives email to process employees leave request after RPTARQEMAIL program runs
3) Leave is reaching the manager's business workplace in R/3 so this verifies workflow is working and the leave is being directed to proper manager for approval
4) Proper roles have been assigned to manager and verified in PRD
*Also, the leaves were appearing in the manager's UWL at one point but no longer appearing. This makes it more confusing!
Does anyone have any suggestions/ideas as to what may have happened?
Any feedback would be greatly appreicated!
Regards,
Brian

Hi:
We transported our ESS/MSS changes from the DEV client to STG client. I have verifiied the follwoing settings in STG:
1) SWU3 - all connections are green.
2) Workflow template and tasks - all are assigned as general task with agents assigned
3) Configuration in SAP contains the correct WF template for leave processing
4) UWL has been regenerated
I am able to submit a leave request under ESS user. I check workflow and it shows leave has been submitted and waiting for Manager to approve step.
However, under MSS user the leave request is not showing up in the UWL. All configuration on backend and the items noted above have been verified.
Is there configuration or a connection on the portal side that I need to check? Or anywhere else? Any input would be greatly appreciated.
Regards,
Brian

ESS Travel links not appearing (EHP4)

Hi there,
We are on EhP4 and trying to implement travel management.
Currently we are only seeing the following links:
Travel Information
Route planning
My travel Profile
Personalize data
Switch personal number
Unlock personal number
We want to see the other links as well like the create travel request, delete travel request etc
I have forwarded the travel consultant the PCD links for the pages and he has added the links to the back- end of the FI system but the links still does not apprear on the portal.
Additional notes:
For ESS we are using the HR "box" and for the travel management we are using the FI" box". We are pionting the travel iview to the FI "box". To test this the Travel consultant did some some config and it is showing up on the portal under My travel profile.
Please can you assist me?
What Iu2019m I missing?
Many thanks in advance
Jo-lize

Hello Jolize777
Are you using the standard framework page?
Is the user mapping to an employee?
Travel web roles are assing to the user?
The employee has travel priviliges?
If the answer is yes to all of them.
Check on the the services table of the home page framework, and add the services that you need, you can remove the travel proxy_class and put a new one with your requirements.
Regards
Jose

CHARM Tab does not appears -- solution manager

Hi Experts,
I want to configured CHARM but in tx SOLAR_PROJECT_ADMIN in System Landscape -- Change Request Tab does not appear
Also tx solar01 is locked! the project doc for example . But in scope a have not checked the link.
Any clue?

Hello,
In SOLAR_PROJECT_ADMIN are you creating a project or runing an analysis?
The Analysis screen is not tabbed, it is a tree.
Change request management apears under Solution.
When you create a project, there is not a Change Management Tab.
So are you refering to creating the project or performing the Analysis?
Regards,
Paul

Request not appearing in QA Worklist

Hi,
We have a 3 system landscape and the QA approval procedure is configured. Any transport request that is created and released in the DEV box is automatically trnapsorted to the QA (batch program) and then gets appended to the QA worklist for the approval to be transported tot he PRD system.
We have a typical situation here - we got a transport request from a third party, we added that in the DEV queue and imported it there, then we forwarded the request to the QA box and it was imported by the regular batch program. But it does not appear in the QA worklist.
Can anyone help - how to get this in the QA worklist or is it that the 3rd party request cannot be added to the QA worlist.
Regards,
Hasnain

Hi Ahmed, It seems that you have resolved the issue. If you did can i have a small clarification since am facing the same problem.
We have 3 system landscape and when the request is released from DEV system it does not appear in QA worklist, for which we need to manually import the request without approval from QA and the same exists in QUA system QA worklist once imported.
Do you know why the request is not displayed in DEV system for QA once released. Though we have batchjob running every 5 mins to import the TR we are manually importing the same since it doesnot appear in import queue of QUA as they were not approved my DEV QA worklist.
But in your case that was 3rd party request which is not appearing in QA worklist.
I hope everything will be fixed once the QA worklist for DEV is fixed.
Can you help me out..?
Thanks in advance...
Suri tyson

Leave Request - Not Appearing in UWL

Hi,
I am facing a problem with the leave request not showing up in the manager's uwl. Under ess user, I am able to submit the leave request and it has a status of 'sent' in RPTARQDBVIEW. The workflow status shows as 'started'. When I select the work item and check the workflow log, under the 'view:workflow agents' tab it shows 'work item reserved' for the mss_user. I'm not sure if this correct. Does anyone know why it would show 'work item reserved'? In the workflow, it stops just before the 'Process Request' step.
I verified that all tasks are set as general tasks.
Does anyone have any suggestions as to what else to check? Please help.
Regards,
Brian

Hi:
We transported our ESS/MSS changes from the DEV client to STG client. I have verifiied the follwoing settings in STG:
1) SWU3 - all connections are green.
2) Workflow template and tasks - all are assigned as general task with agents assigned
3) Configuration in SAP contains the correct WF template for leave processing
4) UWL has been regenerated
I am able to submit a leave request under ESS user. I check workflow and it shows leave has been submitted and waiting for Manager to approve step.
However, under MSS user the leave request is not showing up in the UWL. All configuration on backend and the items noted above have been verified.
Is there configuration or a connection on the portal side that I need to check? Or anywhere else? Any input would be greatly appreciated.
Regards,
Brian

"Ask to buy" requests not appearing in notification center (family sharing)

I understand that if one misses an "ask to buy" request from a family member from the lock screen, it is supposed to be available in the notification center. However, these requests are not being logged in my notification center. There doesn't seem to be a setting in Settings to turn on or off these type of notifications.
Any idea why they are not appearing in the notification center?

Hi,
Same issue here. I've logged in and out of the AppStore and still the same issue. I have 3 kids, each with their own device, and each one is REQUIRED to "Ask to Buy". Neither my wife or I get any notification to approve. I've checked my Mac as well as the Family Sharing on both iPhone 6's and everywhere shows our family listings correct.
It cannot be THIS HARD to figure out. Apple must be having some issues, however this is extremely frustrating. No one can buy any apps?!??!?! You'd think they'd like to sell more stuff?!
Please help! Now my son needs apps for school and he cannot get them on his iPad. Even on the App store it says "approve on this device with parent" and that link won't work.
Thanks.

New gmail messages do not appear in Mail 5 inbox

I have a new Imac and trying to setup email accounts. My Hotmail account has no issues. My gmail account is struggling to put the new messages in the Inbox. The messages appear in the "all mail" down below.
Sometimes the messages will appear in the Inbox and then disappear. The next time I open Mail, the spinning marker will be beside the gmail inbox icon and then not load any messages in the inbox.
Any suggestions?

I assume you are referring to folders you created other than main mailboxes.
Did you checked the Label Section in settings at the gmail site and the box to show in IMAP is checked.
Is IMAP and not POP is enabled in the Forwarding and POP section.
Repair permissions with disk utility and restart the computer.
If it isn't working now, try deleting one of the accounts and add it back in. When you add it back, make sure it is set as IMAP.
You could also create a new user for testing. Log into the new user and create the accounts there. Whether or not it works there will tell us whether or not it is a user account problem or not.

Travel costs not appearing in the sttlement and in standerd form prf0

Dear Experts.
i could'nt get travel costs in the settlement and in the prf0 -standerd form
but i could get meals perdiem reimbursement and accomidation reimbursement.
could u pls pass some information
i have configured reimbursements for travel costs in the tables
V_T702N_H
copy from trip
copy from trip
travel costs flat rates for all trips.
in* V_T706F*
Car
All Vehicle Classes
All Employees
No Cumulation
India
India Thiruvananthapuram
Business Trip
All Trips
All Trips
INR Indian Rupee
100.00
1,000.00
and in the table V_T702N_A
1 3 0 0 2 1 0 1 1 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
out put in prf0 is like this
                                Travel costs
                   Car Tax-free Comp.          Tx-free    Addit.    Reimburs
Date               cl. amount amt. Mls/kms   amount    amount     amount
Tot. amounts travel costs in INR                  0.00      0.00       0.00
kindly help
thanks
vj
Edited by: k vj on Nov 11, 2009 9:54 AM
Edited by: k vj on Nov 11, 2009 12:24 PM
Edited by: k vj on Nov 12, 2009 6:05 AM

Hi Alagesan,
It seems the allocation structure for services is not maintained in controlling area. Ask your CO guy to maintain it properly.
Prior to this please check that you have assigned value categories to the cost element in Plant Maintenance & Customer service.
Thanks

Status of elements not appearing in Management Cockpit

The Problem is as follows:
when you look into the management cockpit and ask to display data from, for
example, December 2004, the cockpit shows all the four walls with
elements without status, when, in fact, all the elements have a status.
You can notice they have a status (green, yellow or red) when you click
and see the detail (for example, the financial situation is shown with
no status, but if you go into financials and then to the general
overview, for example, you can see that you've got maps and status
there. So, in the financial situation you should have a status as well).
I am using SAP_BW 3.10
Looking forward to hearing from you.
Regards,
Deepak

hi,
Usually when I browse sourcing area the last work item should be my shopping cart line item.
But I am not able to find the line item in sourcing area,I searched in all possible ways,do you think I missed some sort of settings regarding this.
regards,
IGA.

SQL Server Agent not appearing in Management Studio

Hi there,
I have SQL Server set up on a server and I can't see the Agent in Management Studio.
When I check the services it says it is there and started.
I have the Enterprise edition installed.
Funny thing is it doesn't show when I am on the server itself through Management Studio, however, on my local pc, when I connect to the server through Management Studio, I can see the Agent through there and I have jobs there that run successfully and everything.
Its just when I log directly on the box and load up Management Studio, I don't see it.
Any thoughts?
Thanks!

a) Is there a possibiity that you are using SQL Server Management Studio Express edition, on your server instead of (full or complete edition of management studio that came with SQL enterprise edition media)
one way to tell if you are using sql express studio is under management you will be missing Resouce Governor under management node, Resource governor mangeability feature is only available if you have install management studio that comes with an enterprise
edition only
OR
b) account under which you are logged in your server does not have privileges to view SQL Server Agent (the user need to be member of certain role in msdb database to view sql agent see
http://msdn.microsoft.com/en-us/library/ms188283.aspx )
c) When you installed SQL managment stuido, which option did you choose for management studio (Basic or Complete)..?

Technical Systems Not appearing in Managed Sytem Configuration

Hi Experts,
I am doing Solman_setup after upgrade.I am in Managed system configuration step.I have synchronized Abap and java systems through RZ70 and NWA respectively to Solamn Local SLD and hence they are also appearing in LMDB (technical system tab).However when I am opening Managed System Configuration page no technical system (Abap or Java) is found (except solman Abap and solman Java) technical system tab page (find the screen shot for ur convenience ).Can any one help me out to find the solution.
Thanks
Aditya Roushan

Hi
Please check the Synchronization job between SLD and LMDB is running fine.
Did you finish all the steps(SLD Setup) System Preparation?
If the issue still exist please de actviate the SLD and recreate again
Run the SLD and LMDB Sync job again after the recreation Step: SLD Setup
Kind Regards,
Phaneendra Kakani

Travel Request not appearing in Manager's inbox

Similar Messages

Maybe you are looking for