TREX Name Server Disabled

Hello,
I am running EP6 SP2 Patch29. When I click on System Admin - System Configuration - Knowledge Management - Index Administration and the TREX Monitor. I get a message that Name Server Disabled. The other serivces listed are connected.
I went to the TREX Server and I can open a telnet connect on that server on port 8355, which is what is configured as the Name Server port.
Any ideas why I get Name Server Disabled when I looked at the TREX Monitor?
Thanks,
Keith

Hi Keith,
Check the parameters(Name Server parameters .. if anything is disabled, change it) of TREX Service in Visual Administrator and check the parameters in topology.ini file.
Hope this will solve your problem.
Regards,
Srinivas GV.

Similar Messages

Com.sapportals.wcm.WcmException: TREX Name Server

Hello SAPMAN;
When try search in Portal show this error,
Search Failure
Error during search occurred - com.sapportals.wcm.WcmException: TREX Name Server (including back-up servers) is down or not accessable. (Errorcode 7217)
An unexpected severe error occurred during the search call. If the situation persists, inform your system administrator.
In Visual Administrator the trex service is ok.
Regards.

Trace error,
[290512] 2010-04-23 12:52:19.643 e TNS          TNSClient.cpp(00599) : sendRequest to spcp1appitr01:30301 failed with NetException. data=[getvalue](S)client_id=spcp1appitr01:0/291980/1920...
[290512] 2010-04-23 12:52:19.643 e TNS          TNSClient.cpp(00497) : nameserver spcp1appitr01:30301 not responding after 1 retries. giving up.
[290512] 2010-04-23 12:52:19.643 e TrexNet      EndPoint.cpp(00087) : ERROR: failed to create Endpoint 10.130.14.15:0 reason: invalid port
[290512] 2010-04-23 12:52:19.643 e AlertServer TRexAlertMonitor.cpp(00598) : An exception occured while getting configuration from the active master (name) alert server!
[291500] 2010-04-23 12:53:10.174 e NameServer   TREXNameServer.cpp(00542) : shared memory not initialized after 10 retries (state=Reinit). disabling shared memory
[291500] 2010-04-23 12:53:11.143 e TrexNet      EndPoint.cpp(00243) : ERROR: failed to open channel 10.130.14.15:30301! reason: connection refused
[291500] 2010-04-23 12:53:11.143 e TNS          TNSClient.cpp(00599) : sendRequest to spcp1appitr01:30301 failed with NetException. data=[getvalue](S)client_id=spcp1appitr01:0/292784/1920...
[291500] 2010-04-23 12:53:11.143 e TNS          TNSClient.cpp(00497) : nameserver spcp1appitr01:30301 not responding after 1 retries. giving up.
[291500] 2010-04-23 12:53:11.143 e TrexNet      EndPoint.cpp(00087) : ERROR: failed to create Endpoint 10.130.14.15:0 reason: invalid port
[291500] 2010-04-23 12:53:11.143 e AlertServer TRexAlertMonitor.cpp(00598) : An exception occured while getting configuration from the active master (name) alert server!
Regards.

How to configure trex name server

hi all
while creating index i am getting the error
Index could not be created; creating index failed: TREX Name Server (including back-up servers) is down or not accessable. (Errorcode 7217)
for the above error i need to configure the trex name server using TREX Configuration in the J2EE Engine in j2ee visual administrator .
can any one tell me the clear path that where to configure the above and where j2ee visual administrator installed how to configure the name server
awaiting for replies
regards
ganesh

Hi Ganesh,
In order to access the Visual Administrator, go to Start > Programs > SAP J2EE Engine > Visual Administrator. After you login, you will see 2 nodes i.e. Dispatcher and Server. Expand the Server node. Then go to "Services" and expand it. Then go all the way down to "TREX Service". Then on the right hand side, go to the property "nameserver.address" where you will key in "tcpip://<nameserver>:<port>". Then hit "Update" and click on the "Save" button. Then when you go to TRex Monitor, you should be able to see the Name Server running. Hope this helps.
Thanks,
Sri
P.S Please rewards points if you find this helpful. Thanks.

How To Configure TREX Name Server&Port for UDDI Service Registry Settings

Hello Experts,
we are using CE 7.1 SP 4 and I would like to use the trex service in the Service Registry.
I use \NWA\Service Registry Configuration\Service Registry Settings\Keyword Search and want to test the TREX Communication using the Test Connection Button.
If I do so, I receive "Connection to TREX not successful".
When I press the Update TREX button I receive this exception:
com.sapportals.trex.TrexException: TREX Name Server (including back-up servers) is down or not accessable. (Errorcode 7217)
I tried to configure the trex.service with the two parameters: nameserver.address and nameserver.backupserverlist -> tcpip://myhostname.mydomain:30001 (Instance 00).
I am not sure if the port number is correct -> is there a way to lookup the correct port number?
Is there something else I should configure?
Thanks for help, best regards
Thomas

Hi Ganesh,
In order to access the Visual Administrator, go to Start > Programs > SAP J2EE Engine > Visual Administrator. After you login, you will see 2 nodes i.e. Dispatcher and Server. Expand the Server node. Then go to "Services" and expand it. Then go all the way down to "TREX Service". Then on the right hand side, go to the property "nameserver.address" where you will key in "tcpip://<nameserver>:<port>". Then hit "Update" and click on the "Save" button. Then when you go to TRex Monitor, you should be able to see the Name Server running. Hope this helps.
Thanks,
Sri
P.S Please rewards points if you find this helpful. Thanks.

Com.sapportals.wcm.WcmException:TREX Name Server Error

Hi,
I have developed a Customised Search Iview using the STD KM Search Iview
But I getting the following error while I input a search criteria and click on the Search Button :
"Error during search occurred - com.sapportals.wcm.WcmException: TREX Name Server (including back-up servers) is down or not accessable. (Errorcode 7217)"
Please can anyone let me know why is this error been thrown.
Regards,
Vaishali.

Hi.
I am having the same error, i already check the monitor and it shows the same error:
Error during search occurred - com.sapportals.wcm.WcmException: TREX Name Server (including back-up servers) is down or not accessable. (Errorcode 7217).
There are two machines accessing TRX and one is working fine the other one does not. I made a ping from epweb to trx and does not respond. If i make de ping from epprd to trx it responds fine. What can i do?.
TRX is up and working fine.
Thanks for the help.
Edited by: Juan Pablo Toledo Corredor on Apr 16, 2009 8:13 PM

TREX Name Server (Errorcode 7217)

Hi,
I have the EP 7.0.
When I try to use the search tool (TREX), to find some file, I recieve de folow message:
class com.sapportals.trex.TrexException
TREX Name Server (including back-up servers) is down or not accessable. (Errorcode 7217)
Details:
com.sapportals.trex.TrexException: TREX Name Server (including back-up servers) is down or not accessable. (Errorcode 7217)
 at com.sapportals.trex.tns.TNSClient.sendRequest(TNSClient.java:537)
 at com.sapportals.trex.tns.TNSClient.getActiveHttpServers(TNSClient.java:349)
 at com.sapportals.trex.tns.TNSClient.getHttpServer(TNSClient.java:208)
 at com.sapportals.trex.core.util.HttpRequest.getServerUrl(HttpRequest.java:604)
 at com.sapportals.trex.core.util.HttpRequest.run_it(HttpRequest.java:233)
 at com.sapportals.trex.core.util.HttpRequest.run(HttpRequest.java:111)
 at com.sapportals.trex.core.util.HttpRequest.run(HttpRequest.java:95)
 at com.sapportals.trex.core.admin.HttpAdmin.showIndex(HttpAdmin.java:536)
 at com.sapportals.trex.core.admin.AdminManager.showIndex(AdminManager.java:650)
 at
What I have to do to resolve this problem?

I looked the files and I found some messages like this:
[4112] 2006-12-01 10:02:43.625 e TNS_Timing WatchDog.cpp(00162) : info LocalWatchDog: detected unknown->inactive httpserver@http://portalapprod:30205/TREXHttpServer/TrexIsapiExt.dll
[2264] 2006-12-01 13:00:06.140 e TNS_Timing WatchDog.cpp(00157) : info LocalWatchDog: detected active httpserver@http://portalapprod:30205/TREXHttpServer/TrexIsapiExt.dll
[2452] 2006-12-01 13:11:16.375 e TNS_Timing WatchDog.cpp(00157) : info LocalWatchDog: detected active httpserver@http://portalapprod:30205/TREXHttpServer/TrexIsapiExt.dll
[2452] 2006-12-01 13:11:16.390 e TNS_Timing WatchDog.cpp(00157) : info LocalWatchDog: detected active preprocessor@portalapprod:30202
[2452] 2006-12-01 13:11:16.390 e TNS_Timing WatchDog.cpp(00157) : info LocalWatchDog: detected active indexserver@portalapprod:30203
[2452] 2006-12-01 13:11:16.390 e TNS_Timing WatchDog.cpp(00157) : info LocalWatchDog: detected active queueserver@portalapprod:30204
[2452] 2006-12-01 16:30:38.831 e TrexNet EndPoint.cpp(00210) : ERROR: failed to open channel 192.168.151.11:30202! reason: connection refused
[2452] 2006-12-01 16:30:38.831 e NameServer TREXNameServer.cpp(00712) : pingTREXService(preprocessor@portalapprod:30202) net exception while connectingOpenChannelException at EndPoint.cpp(00211):
message: an error occured while opening the channel
info: connection refused
param: 192.168.151.11:30202
[2452] 2006-12-01 16:30:39.917 e TrexNet EndPoint.cpp(00210) : ERROR: failed to open channel 192.168.151.11:30203! reason: connection refused
[2452] 2006-12-01 16:30:39.917 e NameServer TREXNameServer.cpp(00712) : pingTREXService(indexserver@portalapprod:30203) net exception while connectingOpenChannelException at EndPoint.cpp(00211):
message: an error occured while opening the channel
I tried to start the TREXadmin.bat but it didn't work and show the message "Shared Memory Not Initialized. Retry in 5 second..."
Do you have any another idea?

TREX-Name server error

Dear All,
We have configured TREX 6.1 on our Portal.
The Installation is complete & now we are carrying out the post installation activities.
We are getting the error like -
"The name server is not running or no name server is configured in TREX Service Properties."
Through Visual Administrator the TREX Service entry for name server are completed.
When I stop/start the TREX service the process for TREXNameserver is running. I then go to the Portal & click System Configuration - --TREX Monitoring the above message comes & in the Task Manager when I check the process for TREXNameserver it is not running.
Please suggest asap.
Thanks & Regards,
Sameer

Please check if you have done the below
Procedure
 1. On the portal host, edit the configuration file config_local.properties. The information below gives the respective locations of the file:
 <SAP_J2EE_Directory>>clusterserverservicesservlet_jspworkjspTempirjrootWEB-INFportalportalappscom.sap.km.applicationlib
 2. Insert the following line:
trexserver=<hostname>.<domain>
Example: trexserver=mytrexhost.mydomain.com
 3. Restart the servlet engine.
Only EP 6.0: Check the settings in the portal under System Administration → System Configuration → Service Configuration → Applications (Content Catalog) → com.sap.portal.ivs.httpservice → Services → proxy.
If a proxy server is entered there, you have to enter the TREX host in the field http Bypass Proxy Servers.
Also check if you have comfigured the below
http://help.sap.com/bp_epv260/EP_JA/documentation/How-to_Guides/14_TREX60SP1_InstallationGuidePortal.pdf
Message was edited by:
 Jayesh Ghodge
Message was edited by:
 Jayesh Ghodge

Configuring TREX name server using j2ee visual administrator

hi all
i found the go.bat file in the following path in my system
/usr/sap/EEP/JC00/j2ee/admin/go.bat
now i want to run that "go.bat" but i don't know how to run this in linux machine but my portal server is installed in linux machine.so, can any one help me how to run that file in order to configure name server .
and also can any one tell me how to find out the server name and port number in order to fill the following format in name sererver
tcpip://<%nameserver%>:portnumber
plzz help me out
Thks&Rgds
Gnana

Hi,
/thread/77197 [original link is broken]
Regards
Prakash

Trex: Unable to find name server

We are in process of upgrading our portals from EP6sp2 to EP6SP9 and we have trex 6.0 server. Recently we have upgraded our dev portal to EP6SP9 and trying to configure trex fails. I have specified name server in J2EE engine but still I cant create indexes. I restarted the system but still no good.
 when I see trex monitor I get message "The name
server is not running or no name server is configured in TREX Service Properties. Start J2EE Admin to change the
properties."
 When I try to create the index "Index could not be
created; creating index failed: TREX Name Server
(including back-up servers) is down or not accessable.
(Errorcode 7217)"
How do I make my trex work. What am i missing
thanks,
Praveen

Hi,
The server is working and aswell my production server which is EP6SP2 is configured to the same trex server and I can search documents in Production server.
 Just wondering whether do I have to install Trex 6.1 for EP2SP9. I have given the name server as tcpip//<hostname>:8355. ? Any other Suggestion?
Thanks,
Praveen

Configuring name server in j2ee visual admin

hi all
i found the go.bat file in the following path in my system
/usr/sap/EEP/JC00/j2ee/admin/go.bat
now i want to run that "go.bat" but i don't know how to run this in linux machine but my portal server is installed in linux machine.so, can any one help me how to run that file in order to configure name server .
and also can any one tell me how to find out the server name and port number in order to fill the following format in name sererver
tcpip://<%nameserver%>:portnumber
plzz help me out
Thks&Rgds
Gnana

hi dominlik
yeah go file is there but while running the following was displayed
[root@entegdt26 admin]# ls
adminCFG.properties go go.jar lib logviewer-standalone
cfg go.bat launcher log
[root@entegdt26 admin]# sh go
go: line 7: /usr/java/bin/java: No such file or directory
[root@entegdt26 admin]#
can u tell me how to mark it as executable using chmod coz i am not aware of linux
its very very urgent help out only one day i've time with in this i've to configure trex name server and create index in ep
awaiting for reply
Regards
gnana

Name server not updated in development configuration after change of SLD

Hi Guys
Hope you can help me with this one.
We have moved our SLD from one server to another.
After this we changed the name server in NWDI and in NWDS.
In NWDS i removed the development configuration and reimported it, but when I do this, a popup box shows the details of the development configuration and the name server is still the old SLD server. This means that when I start the NWDS I get an error saying that the name server host is unreachable.
Where do I change this?
I found out that the name server is setup in the .confdef file under .dtc\0 in the field called name-server-url. If I change this manually in the file, it works. But if I remove the development configuration and reimport it again, I am taken back to the old name server again.
It seems as if something has to be changed in NWDI, but I can't figure out what.
Can anybody help?
Cheers,
Jacob Vennervald

Hi Jacob,
I would proceed as follows: 
- login to your new SLD 
- go to the technical systems in the landscape area of the SLD 
- in the filter drop down select AS JAVA 
- check if your NWDI has reported to this SLD in the last 12 or 24 hours, you can check this on the "last update" column 
- if your system has reported to this sld the last few hours this is good if not go to the step "change J2ee to new sld" i will descirbe later. 
- remember the name of the system here. it is like sid on dbhostname. 
- got to sld administration (link on top) choose content maintenace in administration 
- in the subset filter select "All with instances" as class set SAP AS JAVA Cluster 
- you should find your system there. click on it. 
- in the new screen find a link in the middle top <nr> associated instances -> click it 
- in the next screen you will see the relationship of the technical system to the rest of the sld data. 
- there should be a topic called "hosted application server" 
- the should be an entry like: system landscape directory: sld on sid on server -> click it 
- here you will see the data for this hosted system. You can find the cim/url definig the SLD you will find the roles. Landscape and name server should assigend and so on here you can chage the SLD url. 
You can although proceed as follows. This as well requieres you nwdi to report and use this sld in j2ee see below if not. 
- on sld startscreen choose landscapes in the landscapes part of sld 
- select landscape type nwdi systems 
- if there is no landscape you can create one 
- in the landscape ypu can assinge systems. The sld should be availabel to choose. 
- once in the landscape you can view the system and you can change the CIM Server url and the roles there aswell its just another view on the content. 
 
you can although check: 
- open name reservation from develpoment part of start screen 
- here you should find a button about enabling or disabling the sld for nwdi usege. this should be of course enabled... 
 
"change J2ee to new sld" Ok and here what to do or to check if you are not sure if your NWDI uses/reports to the new sld. 
- Go to the nwdi server an open Visual admin i asume you are running a 7.0 Di if not let me knoe i can although tell you for CE. 
- ok in VA. select on of your server nodes->services->SLD data supplier. 
- an overview page will show up. 
- select the http settings tab in the lower middle. 
- https settings will tell the j2ee where to report to. Verify the data and change if needed. use the lightinigbolt button on top to transfer data to the sld. have a little patiance if your data is not shown immediately in your sld,. it may take 1-2 minutes until it is shown in the gui. 
- switch to cim client generation tab. those paraemters will tell your j2ee from what sld to read data from. It is important to understand that you may report to one sld but to read from antioher. depending on your sld landscape. The CIm CLient should use the same Sld as your NWDI uses in CMS setting. 
- if all is setup. do a cim client test. 
 
Allright. This is all I know on how the NWDI is integrated in SLD. Hope you can resolve your problem wiht this steps.
 
Have a good time 
Jan

Name server configuration

Hi all,
I have created tracks and developed DCs and it works successfully .Now,I need to create a name prefix for my DCs.Inorder to do this
1) I have confgured the name server at http://hostname:port/dtr/system-tools/administration/NameServerConfiguration
2) I added the name prefix uder name reservation in teh SLD and have enabled the sld as the name server for NWDI.
Moreover in the landscape system that i have defined, I have included the sld as name server by ticking that check box.
with this I guess the name prefix should appear in my NWDS when i try to create a new DC.But then it doesnot appear.the dropdown is in disabled mode
Kindly guide me through
Best Regards
Uma Thirugnanam

Uma,
check these threads
https://forums.sdn.sap.com/click.jspa?searchID=19166202&messageID=6549632
https://forums.sdn.sap.com/click.jspa?searchID=19166202&messageID=6577728
https://forums.sdn.sap.com/click.jspa?searchID=19166202&messageID=6518883
Thanks
Bala Duvvuri

DNS timeout and Name Server timeout between two DC's

Hi All
My clients have a brand new domain built for them, with two domain controllers at separate sites, and one site is having some issues.
At one site (where DC2 is hosted), all users are having 5-10 minute log on delays - once in everything is running without issues. Site where DC1 is has zero issues - they run smoothly, get a nice quick login etc. All users are using redirected folders and
all have the same GPO's applying to them.
DC1 also has periodic issues communicating with DC2 - nslookup using DC2 gives "DNS request timed out. timeout was 2 seconds" on external AND internal queries, but then 5 minutes later will resolve perfectly. During the "DNS time out"
period, trying to resolve DC2 as a Name Server also gives the error "A timeout occurred during validation".
Not sure if these (slow logon and DNS/NameServer time out issues) issues are related but I am at a loss.
Reverse lookup zones are fully created and populated, entries aren't randomly deleting themselves. Replication between both DC's is working fine, no errors and SYSVOL/NETLOGON are sharing fine from both DC's. Occassionally restarting the DNS server services
on both servers will kick them back into talking - but only for around 30sec-1minute, after that they communicate periodically without problems and spend the rest of the time not resolving.
Any ideas floating around, as I am at a loss here. We haven't been able to join more than a few test users to DC2's site for fear of them all calling every day due to long log on periods.

Hi,
Are you pointing each DC/DNS to the other one as primary dns in tcp/ip properties? Can you post a dcdiag /a /f:dcdiag.log from the DC2?
Any warnings/errors in Application log on the client(s) facing issues after they get logged in ? Can you also confirm that users from site with DC2 are having DC at : set | find /I "LOGONSERVER" output?
Hope it helps.
Regards,
Calin
Hi Calin
The DC's were originally pointing at each other for the primary but others prior to posting here suggested that was not best practice anymore and said they should be the other way around - in any case, either direction doesn't resolve the issues.
The only application error the users are getting is :
The winlogon notification subscriber <SessionEnv> was unavailable to handle a notification event.
The winlogon notification subscriber <GPClient> took 84 second(s) to handle the notification event (Logon)
DCDIAG of DC2 :
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
Home Server = CAB1-DC-V01
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: AUS\NDC1-DC-V01
Starting test: Connectivity
......................... NDC1-DC-V01 passed test Connectivity
Testing server: AUS\CAB1-DC-V01
Starting test: Connectivity
......................... CAB1-DC-V01 passed test Connectivity
Doing primary tests
Testing server: AUS\NDC1-DC-V01
Starting test: Advertising
......................... NDC1-DC-V01 passed test Advertising
Starting test: FrsEvent
......................... NDC1-DC-V01 passed test FrsEvent
Starting test: DFSREvent
......................... NDC1-DC-V01 passed test DFSREvent
Starting test: SysVolCheck
......................... NDC1-DC-V01 passed test SysVolCheck
Starting test: KccEvent
......................... NDC1-DC-V01 passed test KccEvent
Starting test: KnowsOfRoleHolders
......................... NDC1-DC-V01 passed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... NDC1-DC-V01 passed test MachineAccount
Starting test: NCSecDesc
......................... NDC1-DC-V01 passed test NCSecDesc
Starting test: NetLogons
......................... NDC1-DC-V01 passed test NetLogons
Starting test: ObjectsReplicated
......................... NDC1-DC-V01 passed test ObjectsReplicated
Starting test: Replications
......................... NDC1-DC-V01 passed test Replications
Starting test: RidManager
......................... NDC1-DC-V01 passed test RidManager
Starting test: Services
......................... NDC1-DC-V01 passed test Services
Starting test: SystemLog
A warning event occurred. EventID: 0x80000109
Time Generated: 12/17/2014 08:25:05
Event String:
A pointer device did not report a valid unit of angular measurement.
A warning event occurred. EventID: 0x80000101
Time Generated: 12/17/2014 08:25:05
Event String:
A pointer device reported a bad angular physical range.
A warning event occurred. EventID: 0x80000102
Time Generated: 12/17/2014 08:25:05
Event String:
A pointer device reported a bad angular logical range.
A warning event occurred. EventID: 0x80000109
Time Generated: 12/17/2014 08:25:06
Event String:
A pointer device did not report a valid unit of angular measurement.
A warning event occurred. EventID: 0x80000101
Time Generated: 12/17/2014 08:25:06
Event String:
A pointer device reported a bad angular physical range.
A warning event occurred. EventID: 0x80000102
Time Generated: 12/17/2014 08:25:06
Event String:
A pointer device reported a bad angular logical range.
A warning event occurred. EventID: 0x80000109
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device did not report a valid unit of angular measurement.
A warning event occurred. EventID: 0x80000101
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device reported a bad angular physical range.
A warning event occurred. EventID: 0x80000102
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device reported a bad angular logical range.
A warning event occurred. EventID: 0x80000109
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device did not report a valid unit of angular measurement.
A warning event occurred. EventID: 0x80000101
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device reported a bad angular physical range.
A warning event occurred. EventID: 0x80000102
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device reported a bad angular logical range.
A warning event occurred. EventID: 0x80000109
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device did not report a valid unit of angular measurement.
A warning event occurred. EventID: 0x80000101
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device reported a bad angular physical range.
A warning event occurred. EventID: 0x80000102
Time Generated: 12/17/2014 08:47:55
Event String:
A pointer device reported a bad angular logical range.
......................... NDC1-DC-V01 failed test SystemLog
Starting test: VerifyReferences
......................... NDC1-DC-V01 passed test VerifyReferences
Testing server: AUS\CAB1-DC-V01
Starting test: Advertising
......................... CAB1-DC-V01 passed test Advertising
Starting test: FrsEvent
......................... CAB1-DC-V01 passed test FrsEvent
Starting test: DFSREvent
There are warning or error events within the last 24 hours after the
SYSVOL has been shared. Failing SYSVOL replication problems may cause
Group Policy problems.
......................... CAB1-DC-V01 passed test DFSREvent
Starting test: SysVolCheck
......................... CAB1-DC-V01 passed test SysVolCheck
Starting test: KccEvent
......................... CAB1-DC-V01 passed test KccEvent
Starting test: KnowsOfRoleHolders
......................... CAB1-DC-V01 passed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... CAB1-DC-V01 passed test MachineAccount
Starting test: NCSecDesc
......................... CAB1-DC-V01 passed test NCSecDesc
Starting test: NetLogons
......................... CAB1-DC-V01 passed test NetLogons
Starting test: ObjectsReplicated
......................... CAB1-DC-V01 passed test ObjectsReplicated
Starting test: Replications
......................... CAB1-DC-V01 passed test Replications
Starting test: RidManager
......................... CAB1-DC-V01 passed test RidManager
Starting test: Services
......................... CAB1-DC-V01 passed test Services
Starting test: SystemLog
An error event occurred. EventID: 0x0000272C
Time Generated: 12/17/2014 08:30:22
Event String:
DCOM was unable to communicate with the computer 139.130.4.4 using any of the configured protocols; requested by PID 1810 (C:\Windows\system32\dcdiag.exe).
An error event occurred. EventID: 0x0000272C
Time Generated: 12/17/2014 08:30:43
Event String:
DCOM was unable to communicate with the computer 203.50.2.71 using any of the configured protocols; requested by PID 1810 (C:\Windows\system32\dcdiag.exe).
An error event occurred. EventID: 0x0000272C
Time Generated: 12/17/2014 08:31:05
Event String:
DCOM was unable to communicate with the computer 8.8.4.4 using any of the configured protocols; requested by PID 1810 (C:\Windows\system32\dcdiag.exe).
An error event occurred. EventID: 0x0000272C
Time Generated: 12/17/2014 08:31:27
Event String:
DCOM was unable to communicate with the computer 8.8.8.8 using any of the configured protocols; requested by PID 1810 (C:\Windows\system32\dcdiag.exe).
......................... CAB1-DC-V01 failed test SystemLog
Starting test: VerifyReferences
......................... CAB1-DC-V01 passed test VerifyReferences
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test
CrossRefValidation
Running partition tests on : aus
Starting test: CheckSDRefDom
......................... aus passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... aus passed test CrossRefValidation
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test
CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running enterprise tests on : swms.com
Starting test: LocatorCheck
......................... swms.com passed test LocatorCheck
Starting test: Intersite
Doing intersite inbound replication test on site AUS:
......................... swms.com passed test Intersite
SYSVOL is sharing OK, these errors are occurring when DC1 is performing backups and comes good a few seconds later)
The DNS failures are not on the NIC of each server they are the forwarders for the server, not sure why they are failing as DNS lookup is running fine and the IP's are resolving correctly within the forwarders.
set | find /I "LOGONSERVER"
C:\Users\Christopher.McCartne>set | find /I "LOGONSERVER"
LOGONSERVER=\\NDC1-DC-V01
NDC1 = DC1
CAB1 = DC2
The users are logging onto NDC1 currently as I did switch around their DNS servers to have DC1 as their primary to test if this resolved the logon times. It didn't so I've switched them back and will re-run the check to see which server is the logonserver.

Flat file connection: The file name "\server\share\path\file.txt" specified in the connection was not valid

I'm trying to execute a SSIS package via SQL agent with a flat file source - however it fails with Code: 0xC001401E The file name "\server\share\path\file.txt" specified in the connection was not valid.
It appears that the problem is with the rights of the user that's running the package (it's a proxy account). If I use a higher-privelege account (domain admin) to run the package it completes successfully. But this is not a long-term solution, and I can't
see a reason why the user doesn't have rights to the file. The effective permissions of the file and parent folder both give the user full control. The user has full control over the share as well. The user can access the file (copy, etc) outside the SSIS
package.
Running the package manually via DTExec gives me the same error - I've tried 32 and 64bit versions with the same result. But running as a domain admin works correctly every time.
I feel like I've been beating my head against a brick wall on this one... Is there some sort of magic permissions, file or otherwise, that are required to use a flat file target in an SSIS package?

Hi Rossco150,
I have tried to reproduce the issue in my test environment (Windows Server 2012 R2 + SQL Server 2008 R2), however, everything goes well with the permission settings as you mentioned. In my test, the permissions of the folders are set as follows:
\\ServerName\Temp --- Read
\\ServerName\Temp\Source --- No access
\\ServerName\Temp\Source\Flat Files --- Full control
I suspect that your permission settings on the folders are not absolutely as you said above. Could you double check the permission settings on each level of the folder hierarchy? In addition, check the “Execute as user” information from job history to make
sure the job was running in the proxy security context indeed. Which version of SSIS are you using? If possible, I suggest that you install the latest Service Pack for you SQL Server or even install the latest CU patch.
Regards,
Mike Yin
If you have any feedback on our support, please click
here
Mike Yin
TechNet Community Support

NWDI for the 04s preview fails with 'SLD name-server configuration error'

After the installation, everything seems to work fine except that when I go to CMS, the links on the top seems to be hardcoded to point to http://pwdf3102:50100/dtr, even in the Domain Data. When I tried to change it to my local server, it keeps complaining about "Unexpected error; inform your system administrator: <Localization failed: ResourceBundle='com.sap.cms.util.exception.CMSExceptionMessages', ID='SLD name-server configuration error', Arguments: []> : Can't find resource for bundle java.util.PropertyResourceBundle, key SLD name-server configuration error"
Any suggestions on how to work around this? Thanks.

Brian,
Try to import the model file first by going to SLD->Administration->Import CIM Model. If the problem sticks, then try to remove the systems. The preview version has lots of pre-exist system name in the technical system, which you can find giving errors since they're not reachable. So you can remove them from SLD (Home->Technical Systems) if they are preventing you from procceeding.
You need to go to http://server:port/dtr/system-tools/administration/NameServerConfiguration to update the name server as well.
Hope this helps...
Message was edited by: Yujian Yan

TREX Name Server Disabled

Similar Messages

Maybe you are looking for