Trial Première pro CS3 combined with Sony DHR-1000NP/No sound rendering the Première Project

Dear friends,
I am a belgian and I have many years of good experience with Pinnacle DV500, Adobe Première 6.0 and the Sony DV Recorder DHR-1000NP.
As I want to make a further step, I downloaded the trial of Adobe Première Pro CS3; I installed this trial on 2 OTHER computers, Windows Professional XP , SP2. With both I have the same problem!
I get good .avi's from my DV tapes, played with the same Sony DV Recorder DHR-1000NP, over a fire wire, connected with the OHCI of the computer.
When playing the obtained Première project, the video and audio on the screen and the amplifier of the computer, are perfect; the videosignal over the firewire and the Sony DV Recorder DHR-1000NP is also perfect, but there is absolutely NO audiosignal reaching the Sony DV Recorder DHR-1000NP.
Who can explain me how I should manage that problem?
Thank you for helping!
With my best regards,
Marc

Beste Marc
Ik heb vandaag de upgrade gedaan naar Premiere Pro CS3. Ik werkt normaal op XP Pro, met capturekaart DVStorm2 (waarmee ik via Premiere Pro 1.5 goed kon werken. Hierop hangt mijn Sony DHR-1000NP.
Na de install van de CS3-versie heb ik geconstateerd dat de DVStorm2 niet meer werkt. Dus ik naar de winkel om een PCI-poort IEEE1394.
Het rare is nu...
wanneer ik de DHR-1000 hierop aansluit start Premiere CS3 op, maar vertelt me dat ik niet in EDIT-mode kan. Capture-window opent, ik kan de video besturen, maar de record-button is disabled.
Met een kleine camera (sony DCR-trv270e) lukt het wel.
Mijn vraag... hoe heb jij jouw DHR-1000 aan de praat gekregen?
Er is duidelijk niets mis met de PCI-kaart, wel met het toetsel dat ik aansluit.
In configuratiescherm komt onmiddellijk wanneer ik de DHR-1000 aansluit een "other devices" warning, geel vraagteken, met AV/C tuner, driver not installed. DOen heeft geen zin, er is geen driver voor.
Ik zou het echt op prijs stellen mocht je me op de goede baan brengen. Ik wil je eventueel eens bellen... mijn nr is 0485/30 31 97.
Van harte bedankt
Stef Ryckmans - Kortenberg

Similar Messages

Pre Pro CS3 compatible with Windows 7 Home?

I'm currently running Pre Pro CS3 on my dieing XP. Looking to purchase Sony Series F- Quad core i7 740 QM (173 GHz with Turbo Boost to 2.93 GHz), NVIDIA GeForce GT 425M GPU (1GB VRAM), 640 GB Hard Drive (7200 RPM), 8 GB DDR SDRAM, with Windows 7 Home Version. Will Pre Pro CS3 run with this. Can't afford to purchase puter and Pre Pro upgrade both. My concern is 64 bit Windows 7 with CS3. Advice?? I'm not puter literate enough to build my own. This Vaio from Sony is about $1,400.

Is WinXP compatilbility mode a setting in Windows 7?
Computer- now looking at Dell XPS 17, also a laptop. i7 840 QM, NVIDIA Ge Force GT 445M 3 GB, 12 GB Shared Dual Cahannel DDR3, Hard drive- 1.28 TB (2x 640 GB) 7200 RPM. I'm choosing a laptop to travel. This is $2,300, out of my range- but can make it work. How does this look to you? I shoot mostly SD presentations with a Sony XD Cam EX- the PMW EX1. These presentations are about 2 hrs. long. I shoot HD when playing with outside scenery- hobby level.
I do some animation work (play), short intros and demos. I appreciate your advice in this. Thanks- Dorian

My macbook pro won't stop making noise! It sounds like the fan but I'm not sure. Any ideas?

my macbook pro won't stop making noise! It sounds like the fan but I'm not sure. Any ideas? It's really worrying me because I haven't had it for up tp 2months and last week everytime I switch it on it makes sooo much noise. And I treat like an egg so I don't understand whats going on.

Hey,
My friend had a very similar issue to yours. The issue came down to the pins of the MagSafe not meeting with the MacBook perfectly causing the lights and the transfer of power to be wacko. I'm not sure if this is issue that your experiencing, but its worth checking out the pins and the MagSafe area on your MacBook for debris.
Troubleshooting Magsafe power adapters with stuck pins
If that is all clear, then I would suggest you call AppleCare or take it in to an Apple Store to have it checked out.
Tom

Premier Pro CS3 crashes with Canon 7D HD files

I am just putting together a promo for a client, shot in HD on my Canon 7D. Everything went fine until 3 minutes into the project when Premier Pro CS3 refuses to render more than 1:30 minutes. (I already changed preferences to "Optimize rendering for Memory") Also the preview window is blanced out White and Black further down the project time line (even after changing back to:"Optimize rendering for Performance". Also now Premier starts crashing everytime I add a sound track. It looks as if the Canon 7D .mov files are too unwieldy for my new 12GB iMac 2,8 GHz Intel Core i7 (OSX 10.6.3).
I need some urgent help please, as my job in in jeopardy.
Should I convert my canon .mov files into H.264 first or what is the best way to work with these files?(using MPEG Streamclip)
Thanks very much for your help.

I am probably too late, but if you have Apple Pro Res 422 Codec available in MPEG Streamclip you should transcode your HD files to that and then bring it into Premiere. They will be easier to work with that way.
Good Luck!

Ad aware pro security combined with the security of the labtob itself?

No doubt somebody can help me with this question. I presume it's a simple one for the most of you.
I just is installed ad aware pro security on my computer. After that it it seems that, when my kids want to see a you tube movie, it played for a little time and then it stops. It looks like it's buffering the movie much slower know.
Also when one site is open and you search for another site the page that appear is from lavasoft. See the link for what appears: http://us.yhs4.search.yahoo.com/yhs/errorhandler?hspart=visicom&hsimp=yhse-lavasoft&type=lavasoft__a...
I also discovered that in the lenovo solution center also runs a firescanner and firewall.
Are the troubles that I describe caused by the fact that I run two virusscanners now? and how can I avoid that lavasoft is forcing me to use their searchmachine?
thanks if you want to help me
Solved!
Go to Solution.

Perhaps Ad-aware Pro is taking a long time to scan. If the page you open is one you have not visited before maybe AA is blocking the IP for security reasons. I believe that Ad-aware Pro uses IP blacklisting. Does it give you the option of disabling IP blocking?
If you continue to have problems I would suggest uninstalling Ad-aware Pro and using Windows Defender that is already installed with Windows 8. It should enable itself after the other anti-virus has been removed -- after a reboot following the uninstall procedure.
If you want extra protection that won't interfere with Defender, try Malwarebytes' Antimalware. There is a a free version for on-demand scanning and manual updating and a pro (paid) version that runs without conflict along with Defender. The pro version is a realtime scanner that auto updates if you desire. Note that if you opt for the paid version, its IP blocking of known bad sites can be disabled by the user if you choose.. This is the official download page: http://www.malwarebytes.org/
ThinkPad: T530 / X1 Gen 2 / Helix - Yoga: Tablet 2 Pro (Win) / Yoga 3 Pro
If you find a post helpful and it answers your question, please click the "Accept As Solution" button.
Lenovo Advocate ~ I am not employed by Lenovo or Microsoft. I am a volunteer.
Microsoft MVP - Consumer Security
SpywareHammer

Adobe Premiere Pro CS3 compatibility with Windows 8.1

Is Premiere CS3 and Encore CS3 compatible with Windows 8.1 64 bit?

I rather doubt it. CS3 was released back in 2007. You might try it.

MacBook pro screen blury with a splash of colors starting in the middle

Hi, I am a new Mac user, and I've had my macbook pro for 6 months now. Yesterday, when I started the computer, the graphics were blurry and then there was a splash of colors (rainbow of colors) covering the middle to upper part of the screen. The rest of the screen was blurry and a bit blinking.
I had been moving around with the laptop the whole but I cannot figure out what happened or what I can do to fix this.
Please help. Thanks.

Welcome to Apple Discussions!
Go to System Preferences>Universal Access and be sure the Zoom is turned off and the Enhance Contrast slider is all the way to the left. Sometimes UA features get turned on accidentally with disconcerting results.
Also, if you can, run the extended version of the Apple Hardware test. You may get a clue in the form of an error code, which could indicate a hardware problem. You should still be under the one year warranty, which should cover whatever is wrong. If UA has not been turned on accidentally, you might have a graphics chip problem or possibly a display problem which Apple would need to fix.
Good luck!

Why is my ipod touch 4th gen with ios 6 only have sound in the speakers but not when I plug my headphones in

My new ipod touch 4th gen with ios 6 wont play soun in the headphones, but only through the speaker when my head phones are unplugged

- You do have the volume set all the way up?
- Have you tried another pair of headphones/do the headphone work in other devices?
- Try cleaning out/blowing out the headphone jack. Try inserting/removing the headphone plug a dozen times or so.
Try the following to rule out a software problem:
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup
- Restore to factory settings/new iPod.
Make an appointment at the Genius Bar of an Apple store. It seems yo have a hardware problem, likely a bad headphone jack.
Apple Retail Store - Genius Bar

Premiere Pro CS5 Compatibility with Sony DSR-25 Deck

I have recently upgraded my computer to support cs5. I have a PNY Nvidia Quadro 2000 graphics card, 8 gb ram, an Intel Xeon 5150 processor and Windows 7 Professional 64-bit. My issue comes with running this system connected via firewire to a Sony DSR-25 deck. When connected, while working on a project, at any point I click on the file menu, it takes several seconds (sometimes half a minute) to load the drop-down menu. This is frustrating, but not entirely detrimental. The main problem is that when I try to capture video (I use the keyboard shortcut F5 to bypass my previous issue) the capture video will usually crash the program, or it will take forever and when I try to capture, it will miss almost the entire first minute of video trying to catch up. It starts rolling the tape, but just doesn't physically begin capturing at that time. I spoke to someone at Adobe and we narrowed the problem down to an issue with the deck, and I am trying to figure out if this deck is absolutely not compatible with this system or if there is some sort of work-around.

Try this:
In Windows: Click on Start -> Control Panel -> System -> Device Manager (up on top left), or just click the Start button and search for "device manager."
Swivel down the entry for "IEEE 1394 Bus host controllers, and right-click on the item that is revealed (will depend on your computer/card manufacturer). Select "Update Driver Software."
Click the "Browse my computer for driver software," and then the "Let me pick from a list" button.
In the list of drivers, select the one that has "(Legacy)" at the end; click Next, and then Close all the dialogs.
Try capturing again.

Premiere Pro CS3 Issue with nVidia 182.50 GeForce Driver?

I recently updated the driver for the GeForce 8800GTS on my other editing workstation because it would sometimes BSOD when preparing to standby with a fault in the nvidia minidriver being reported. I updated to the current version as of today, 182.50 from nVidia's own web site.
After the driver update, I could swear I am seeing more frequent lockups of Premiere when jumping from clip to clip on a timeline of many clips. I can jump maybe half a dozen times and then Premiere will stop responding. Task Manager reports Monitor.exe 'not responding' and a few seconds later, Premiere.exe stops responding and I have to kill the app and start over. I can get it to hang within 20 seconds by just paging down through a few clips on the timeline now. The problem has existed prior, but usually after flipping though several dozen clips, not just a half dozen.
Is anyone noticing problems with more frequent lockups with the 182.50 driver?
SYSTEM CONFIG
Gigabyte GA-P35-DQ6
XFX PVT80GTHF9 GeForce 8800GTS 640MB
Intel Core 2 Quad Q6600
Mushkin Hp2-6400 Ddr2 4gb Kit
4 Western Digital Caviar HD 500G|WD 7K 16M SATA2 WD5000AAKS
SILVERSTONE TEMJIN SST-TJ06S-W Silver Aluminum
Seasonic S12 Energy Plus SS- 650HT Power Supply
LG GGW-H20L Blu-ray Burner
HP LP3065 30" LCD Display
Turtle Beach Montego DDL 7.1 Dolby Digital
Pioneer DVR-112D
NEC Beige 1.44MB 3.5" Floppy Drive Model FD1231H
ZALMAN 9700 LED 110mm 2 Ball CPU Cooler
Contour Shuttle-Pro

Hi Mark I'm running the 182.50 no problem now! I was having problems moving clips as the timeline would double in size and distort and not run correctly. The way I solved it was to to tick "disable display scaling on high DPI settings" in the compatibility section of the Premiere CS3 properties (right click on the icon for CS3 and then choose properties) this may help because with a 30" screen you're sure to have a high DPI setting. Terry

Planning to purchase a new macbook pro to use with Sony XDCAM-EX

Hi,
I am planning to buy a new macbook pro, to use final cut pro to edit XDCAM-EX files.
I will be using a Provio 4MBCR with esata in raid 5.
Is anyone editing XDCAM-EX with a macbook pro?
If so, what is the performace like?
How many layers of video tracks are you able to edit or playback (multicam) without the need to render?
Thanks
Nazmul

You want to also post in the FCP forum area:
http://discussions.apple.com/forum.jspa?forumID=939

Premiere Pro CS3 crash with many video files

Hi
I got back from my Ski vacation with many short (few minutes) videos which I took on Canon P&S camera, about 50 files.
I imported the 50 files to Premiere and tried to work on a movie, but everything works slow and every few commads the premiere crashes.
I notice that for each new file I add to the project 20K of rams are used - 1G for 50 files. I also get message of low resources from premere which recommend to save my works.
The video are standard video (not HD) 30fps, and the project is also standard.
Why is this happening?
Does the premiere have a limitation for number for files to be imported?
Does it have problem with the video format?
How can I overcome this and get a stable editing environment?
Thanks

Sorry for the CAPS Lock, I was writing from my mobile, and for some reason it was locked
so you do not recommend any of those codec package. How are you dealing with all video and audio formats, and subtitles? ffdshow does all for me.
dont' worry I dont have Klite installed
so you belive that if one of two codecs you recommened installed well and working it will solve my problem and work much better then FFDSHOW
I also have the option for converting the file to another format. under what name will I found a sutible format in the conversion software?

Greetings Community: I have a problem with my headphone jack: no sound. The problem is not with the headphones... the jack just does not transmit any sound... any ideas how to fix this? It seems to be a rather strange problem. Thanks for your help.

Any ideas on how to fix a problem with a headphone jack on my
desktop power Mac (mid 2007). I don't have a clue on this one.
Paul

Hi Paul,
...on my desktop power Mac (mid 2007)
Are you sure you don't have a Mac Pro? The last of the PowerMac desktops were discontinued in August 2006.
What does "About this Mac" (in the Apple menu) say about the processor type?

Pro cs3 crashing constantly with extra audio

As described above; when putting another audio wavefile on the timeline [track 2] pro cs3 starts crashing [pc boots!] when moving along the timeline and using the ripple edit tool.
Project doesn't want to open again afterwards...
I use aspect hd to edit hdv in a cineform pal preset.
All updates for pro cs3 are taken care of.
Tried the same thing in Pro 2, and no crashing there.
Currently i am using pro2 again, but i was wondering if there are more people who are experiencing this.

Some additional information:
Sound card is a Claro Plus XT not XP. Used to typing XP heh
Also, the video capture works with the included blackmagic capture software, as well as freeware solutions like VirtualDub and a Japanese freeware program I use. I'm able to capture video and audio without issue on those. Just don't know why Premiere doesn't do it...

Script with Premiere Pro CS3.

Hello,
I would like to know if it is possible to create script for Premiere Pro CS3. Is there a tutorial for that?
The script I would like to create is the following:
Adding a context menu entry to the bin that would execute a prompt command. Do you think it would be possible ?
Regards,
Steven

Unfortunately not. No.
Cheers
Eddie
PremiereProPedia (
RSS feed)
- Over 300 frequently answered questions
- Over 250 free tutorials
- Maintained by editors like
you
Forum FAQ

Trial Première pro CS3 combined with Sony DHR-1000NP/No sound rendering the Première Project

Similar Messages

Maybe you are looking for