Tried to connect to TV, display died

I hope someone can help me with this one!
I have been having some issues lately connecting my ibook to a tv ... kinda of had to fidget with the video plug to get it to work right. It would be almost all the way plugged in but not quite and then it would show up on the tv.
Well, today I was doing this routine again, fidgeting with the plug trying to get it to display on the tv, and the ibook screen was flickering and then it went totally black. The backlight is also not turning on.
I was also in the middle of transferring a 700mb file from an external storage disk to my ipod.
I couldn't get the screen to turn back on and didn't nkow what else to do so I forced a reboot.
Now it still won't turn on. I <think> the harddrive is spinning but i'm not sure. I zapped the pram, and reset the pmu (well i followed the directions, but there's no way to tell whether it actually reset or not). I also put my installation disk in thinking, surely it would boot from that. Well it was spinning in the drive, but still no screen so i have no idea if it is starting or not.
Now I cannot eject the disk, even if I hold down the trackpad button.
Any advice??
Is it possible that it's stuck in some sort of inbetween tv and normal mode??
Or has the logic board failed (please no!)

There is a chance a hardware failure, ie: video component, may be the
problem. I'm not an expert, but sometimes if the connections don't work
correctly and you have to mess with them to make something work, it
may be the video component gone wrong. At the point where both the
external display and internal display share a signal from the video circuit.
And that may be essentially part of the logicboard, at that point.
The machine really needs to have a proper diagnostic to find out what
has gone wrong and get an estimate. If the machine's hard drive content
is not backed up externally, that would be the main concern: lost work.
A possibility exists in trying to see if the computer would boot into FireWire
Target Disk mode (without a display on the computer in question) to see
by visual clues, if the TDM was working. And that'd be something a
second working Mac with FireWire ports would be necessary to have
and use to see if the hard drive of the defective computer is accessible.

Similar Messages

Tried to connect to TV, display (ibook?) died

I hope someone can help me with this one!
I have been having some issues lately connecting my ibook to a tv ... kinda of had to fidget with the video plug to get it to work right. It would be almost all the way plugged in but not quite and then it would show up on the tv.
Well, today I was doing this routine again, fidgeting with the plug trying to get it to display on the tv, and the ibook screen was flickering and then it went totally black. The backlight is also not turning on.
I was also in the middle of transferring a 700mb file from an external storage disk to my ipod.
I couldn't get the screen to turn back on and didn't nkow what else to do so I forced a reboot.
Now it still won't turn on. It is sounding the chime. I <think> the harddrive is spinning but i'm not sure. I zapped the pram, and reset the pmu (well i followed the directions, but there's no way to tell whether it actually reset or not). I also put my installation disk in thinking, surely it would boot from that. Well it was spinning in the drive, but still no screen so i have no idea if it is starting or not.
Now I cannot eject the disk, even if I hold down the trackpad button.
Any advice??
Is it possible that it's stuck in some sort of inbetween tv and normal mode??
Or has the logic board failed (please no!)

i believe that your mlb has failed. if you let it sit
for a while and eventaully high fans come on then its
def dead
mlb? Sorry... not up to speed with the acronyms.
And do you mean let it sit and the fan will come on on its own??

Trouble Connecting 30" External Display to Retina iMac

I'm trying to connect a 30" display (Dell U3011) to a new retina iMac.
On my old Mac Pro (using the DVI connection), the display would connect at 2560x1600 as expected.
On the new iMac (using the MiniDisplay Port to DVI adapter) the display will only connect at 1920x1080.
Am I doing something wrong? Is the lower resolution a limitation of the MiniDisplay Port? Yosemite?
Thanks.

Thanks. I figured out the problem, which amounts to RTFM: Mini DisplayPort to DVI doesn't support 2560x1600, but either a dual-link adapter (http://www.amazon.com/dp/B001IF252C), or a Mini DisplayPort to DisplayPort cable, works just fine.

Tecra A9 - Connecting two external displays using Express Port Replicator

Hi,
I have a Tecra A9 and Express Port Replicator.
I'm trying to connect 2 external displays, one connected on the notebook output and the other connected on the docking station (notebook lid closed, not using the notebook display).
I can only get one to work, does anyone know if this is possible?

Hi
I think you want to connect one monitor to VGA and the other to DVI port.
Is it right?
Well, I found this doc:
http://aps2.toshiba-tro.de/kb0/TSB7B0201000CR01.htm
It depends on the used Tecra A9, if you can get a picture on the DVI out port on the Express Port Replicator (PA3508E-1PRP) or not.
The DVI port on the on the Express Port Replicator is only supported on machines with ATI or nVidia graphic card.
If you have a INTEL graphic card the DVI port on the on the Express Port Replicator is NOT supported.

HT4356 Mavric doesn't support my 5 years old Big Screen Display, OR? Tried to connect my Mac Book Pro after installing Mavric, The Screen didn't work as before. I could only see the Desktop but not the movies for example. What can I do?

Mavric doesn't support my 5 years old Big Screen Display, OR? Tried to connect my Mac Book Pro after installing Mavric, The Screen didn't work as before. I could only see the Desktop but not the movies for example.
<E-mail Edited by Host>

It appears what happened is the installer though it was looking at a empty drive and just went ahead and installed.
I of course am assuming here you didn't use Disk Utility to format the drive first before installing, that would wipe out your files and programs for sure.
So what to do, what to do.
Well there is hope for you as long as the drive wasn't Filevaulted.
I'll explain. When a hard drive writes data for the first time to a drive, it starts at the very top and works it's way down.
When OS X was installed the first time, it was at the top of the drive, unless you upgraded then the upgraded OS X could have been written elsewhere.
Now when you just reinstalled OS X, the new OS went on the top of the drive, overwriting any data that was there previously, so what was there you have lost forever which is about 8GB or so. If it was the previous OS there, then your more in luck because only the old OS X was overwritten.
The remaining space on the drive still can have a copy of your files, provided it's not overwritten yet.
It's because when a hard drive deletes data or reformats, it doesn't remove the data off the drive or overwrites it immediately, it's just made so it's SPACE is available for new files to be written there.
So technically one can recover the deleted data off a non-encrypted/scrubbed hard drive with special software.
The way it does this is it reads the 1's and 0's of the files themselves, and through a lot of figuring out, can tell what that file is and what it belongs too.
So what you will have to do is this:
Create a data recovery/undelete external boot drive
or if you don't have the skills, then take it to a local PC/Mac tech and they can do a direct image of the drive and then you can run Data Rescue on it to rebuild your files.

Hi, i tried to connect my mac book pro on my tv. I can't clci kon mirror displays

Hi, i tried to connect my mac book pro on my tv with my hdmi cable but when i click on displays, "arrangement" doesn't appear . Even if i click on detect displays, it doesn't work. Mirror displays doesn't appear on my screen. Does anybody get any idea ?
Thanks a lot for your help
Victoria

Hello Victoria,
It sounds like you are connecting your MacBook Pro with your television, but you are not getting additional options for your external display.
I found an article with steps to troubleshoot issues with displays. This article is for internal and external displays, so you can skip any steps referring to the internal display. I recommend reviewing the section titled "No video or no signal, image distortion, 'snow,' or flickering" in the following article:
Apple computers: Troubleshooting issues with video on internal or external displays
http://support.apple.com/kb/ht1573
Thank you for posting in the Apple Support Communities.
Best,
Sheila M.

I am trying to connect my mac book pro to the tv via a mini display port and a hdmi cable, the only picture that is on the tv screen is the background picture on my computer, any suggestions?

I am trying to connect my mac book pro to the tv via a mini displayport to a hdmi cable, the only picture on the tv screen is the background picture of my mbp, does anyone know what I need to connect to my samsung tv ?

Hi there. I also bought an iWires mini Display port to HDMI cable and have an LG LED/LCD TV. I plugged it in to my MB Pro and followed the very small writing that came in the package and got both audio and video going. You need to change the audio settings from within System Preferences on your Mac to select your TV as the audio output.
My concern is the data latency - do you experience a delay between moving your mouse on the MBPro and the TV displaying the movement? It is only a fraction of a second, but certainly enough to be annoying, especially in a cable as expensive as the iWire.

I'm trying to connect my 30" Cinema Display to my new Mac Pro along with a new Apple 23'" monitor. The new Apple monitor is fine. On the cinema monitor everything is blown up pretty large. Any ideas on how to solve this?

I'm trying to connect my 30" Cinema Display to my new Mac Pro along with a new Apple 23'" monitor. The new Apple monitor is fine. On the cinema monitor everything is blown up pretty large. Any ideas on how to solve this?

The 30" display needs a DUAL-LINK adapter.
<http://store.apple.com/us/product/MB571Z/A/mini-displayport-to-dual-link-dvi-ada pter>

TS3775 Hi I am trying to connect my mba mid 2011 with an imac 27" 2011 with target display mode tdm. When I am using a thunderbolt cable nothing will work. When I use a minidisplay cable, both screens turn blue but eventually nothing happens. What is the

Hi I am trying to connect my mba mid 2011 with an imac 27" 2011 with target display mode tdm. When I am using a thunderbolt cable nothing will work. When I use a minidisplay cable, both screens turn blue but eventually nothing happens. What is the problem

Your answer is likely in Target Display Mode: Frequently Asked Questions (FAQ) - Apple Support If you are familiar with this document, please re-read it and I suspect you may find something you either missed or are doing incorrectly.

I'm trying to connect my 23" Cinema display to my iMac, need help with connector cable.

I'm trying to connect my 23" Cinema Display monitor to my iMac. The adaptor cable I ordered came with a female, I need a male adaptor. Any ideas where I might find one? I purchased the BlueRigger Mini Displayport Male to DVI Female Adapter Cable.

I have the 23" aluminum Cinema Display. I just can't seem to find the right adaptor for the monitor femal plug on the backside. I've tried a Bluerigger but it was a female adaptor. I believe I need a male.

I am trying to connect a 24" cinema display with mini display port cable to a 24" imac with a displayport - is there a cable for this as these two connections are two different sizes

I am trying to connect a 24" cinema display with mini display port cable to a 24" imac with a displayport - is there a cable for this as these two connections are two different sizes

Hi Gilly,
I have no proof, but I think it will not work with an adapter, only Mini Display Port or Thunderbolt.

I am trying to connect my MacBook Pro to my TV with a mini display port to HDMI converter. Its not working. Any suggestions?

I am trying to connect my MacBook Pro to my TV with a mini display port to HDMI converter. Its not working. Any suggestions?

Depends on your model TV. Read your TV user manual. The newer models have "how to hookup" instructions for computer & games.
You can also do a forum search as well as a Google search.

Hi I have a recent macbook pro 12" (bought in april 2012) model number A1278. I'm trying to connect to a 23" apple cinema display (A1082) this currently is not working - i've bought an additional Apple MB570ZA Mini DisplayPort to DVI Adapter - no luck!

Hi I have a recent macbook pro 12" (bought in april 2012) model number A1278. I'm trying to connect to a 23" apple cinema display (A1082) this currently is not working - i've bought an additional Apple MB570ZA Mini DisplayPort to DVI Adapter - no luck!
im not sure what to do next - can anyone help?
im running OSX 10.7.4

Hi There,
I have had the exact same issue but with a projector.
The issue lies with Mountian Lion 10.8.2.
I tried many a combination with no luck to get HDMI working.
Took my mac into the apple store and came to the conclusion it was the software, so I asked them to install 10.8 onto it (this is destructive so a backup is a must)
Bought my macbook home and voila, now displaying through my projector.
There is a small graphics update after 10.8.1 which seems to be the cause.
Hope this helps.
Thanks.

There is a lot of talk aout there about using a 27" iMac as a display with the mini displayport to displayport cable. It is so exciting! I am trying to connect a PC laptop with a VGA port to a 27" Dell Latitude D620?

In 2010 there was a question about using a 27" iMac as a display with a Dell laptop.
I am trying to connect a work Dell laptop Running Windows XP via a VGA cable to my personal iMac 27"
running iMac 27", Mac OS X (10.6)
Has anyone tried this or know if imac 27" Mini port with a VGA adapter can work?
I apologize if I missed this discussion already
Kind Regards
Gilly

Hi Gilly,
I have no proof, but I think it will not work with an adapter, only Mini Display Port or Thunderbolt.

HI, I am trying to connect my macbook pro, 18 months old, to a projector using the mini display port and a cable/connector to a VGA port on the back of the projector. It all fits but the there is nothing happening? no mirroring option. Any ideas?

HI, I am trying to connect my macbook pro, 18 months old, to a projector using the mini display port and a cable/connector to a VGA port on the back of the projector. It all fits but the there is nothing happening? no mirroring option. Any ideas appreciated. Many thanks

to get to the Detect Displays button you have to hold down the Option key and the button appears.
SeanfromFulham wrote:
Many thanks, however I don't seem to have any relevant options under displays.

Tried to connect to TV, display died

Similar Messages

Maybe you are looking for