Troncature d'un graphe sur labview
Bonjour,
Je voudrais réaliser une troncature d'un graphe obtenu à partir d'une acquisition. Càd une fois j'ai le graphe entre les mains, je ne garde que la partie qui m'intéresse (une sorte de fenêtrage mais la notion de fréquence n'intervient pas ici).
Merci de m'aider
PS: J'ai labview 8.5
Bonjour,
la notion de graphe est une notion d'affichage. Les données qui viennent de votre acquisition sont un tableau (prennant différentes formes selon ce qu'il transporte).
Tronquer votre graphe revient à sélectionner les valeurs qui vous intéressent dans le tableau, et les afficher dans votre graphe.
Un bon vi vallant mieux qu'un long discours, postez votre vi (le plus léger possible) qui montre votre problème...
Cordialement,
V-F
Similar Messages
-
Récupération des données à partir d'une carte mémoire SD sur LABVIEW
Salut tout le monde,
je suis très heureuse de devenir un membre dans ce groupe. bein, je suis entrain de faire un projet qui consiste à enregistrer des données sur carte mémoire sd à partir d'un microcontroleur puis récupérer ces données sur PC. Mon problème c'est que je veux visualiser ces données sur une interface graphique sur LABVIEW mais dommage je suis débutante sur LABVIEW et j'arrive pas à trouver une solution. Quelqu'un peut m'aider??If Google translate is correct, you are trying to log data to a SD card and figuring how to see it in on graph. Since you are getting started with LabVIEW I would suggest using the Write To Measurement File and Read From Measurement File. As shown in this tutorial, you only need to specify the format and file path. I would encourage you to search for code and tutorials about this VIs for more reference, like this one. I hope this helps.
Alejandro | Academic Program Engineer | National Instruments -
Calculer l'aire d'un graph sous Labview
Bonjour,
Je voudrais calculer l'aire d'une zone d'intérêt délimitée sur un graph sous labview. Je m'explique :
Supposons que j'ai fait l'acquisition des données sur un graph. Je voudrais en fait, exploiter ces données, en délimitant plusieurs zones dans ce graph afin d'en calculer l'aire. Auriez-vous la gentillesse de m'orienter vers une solution qui pourra m'épargner un calcul manuel.
Merci par avanceRéponses données sur forum dupliqué à l'adresse suivante:
http://forums.ni.com/t5/Discussions-de-produit-de-NI/Calculer-l-aire-d-un-graph-sous-Labview/td-p/15...
Jérémy C.
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
Travaux Pratiques d'initiation à LabVIEW et à la mesure
Du 2 au 23 octobre, partout en France -
Equivalent de la fonction plot (Matlab) sur Labview
Bonjour,
Je suis débutante un Labview et j'ai un petit problème :
Dans mon VI il y a une partie Matlab qui trace 4 cercle :
for m=1:4
xe(m,: ) = R(m)+cos(alpha)*xc(m);
ye(m,: ) = R(m)+sin(alpha)*yc(m);
end
Si j'écris : plot (xe(m,: ),ye(m,: )) dans la partie Matlab, quand je lance mon VI il me trace bien 4 cercles dans une nouvelle fenêtre.
Maintenant, j'aimerais que mes xe et mes ye (mes cercles) apparaissent sur ma face-avant et non dans une nouvelle fenêtre. Pour ça j'ai essayé d'utiliser Graph XY mais ça ne fonctionne pas (je pense que c'est parce que xe et ye sont tous les 2 en 2D).
J'aimerais donc trouver l'équivalent de la fonction plot de Matlab mais sur Labview. Quelqu'un peut m'aider ?Voilà ce que j'ai tenté de faire dans un premier temps pour afficher mes cercles dans un graph ( en PJ):
(le but final étant de relier mes cercles à la place de sub_ed2)
en PJ, il y a aussi l'affichage de mes cercles avec la fonction plot de Matlab
Pièces jointes :
pb labview2.png 248 KB
pb labview2-bis.png 6 KB
pb labview2-biss.png 32 KB -
Facing memory error during shifting from 3d stem graph to 3d surface graph in labview 2010
hello all,
earlier I was using 3D Stem graph in labview 2010. Now we want to move to Surface plot for same data.when i am trying surface graph it shows memory error.
I have 10240 data.
I was using vector method in stem graph so now for Surface graph i have thought that i have to make matrics of 10240x10240 and its diagonal elements should be my Z co0ordiants.
plz help me out here.
thanks & regards,hello mikeporter,
thanks for reply.I am attaching my Vi. It has some error also.plz look into it.
X and Y are my co-ordinates pairs.I will be having values for these and have to update for same.
Attachments:
Untitled 2_surface.vi 184 KB -
CIE chromacity graph in labview
Has anyone ever implemented CIE chromacity graph in labview.
Please let me know how to approach this problem.Muks
Sorry, I should have been more clear. I can get the required x, y values.
Its plottig these values on a real CIE graph. The discussion you , I have
taken a look that long ago. It discusses how get CIE values, which is
not a problem. Also I am attaching a screenshot of a software which uses
a simple x,y plot, with a reference point, at 0.313 and 0.329 and takes
realtime RGB values values and plots them as a point. Is it posible to do
somehting like this in labview. Either of them is good enough for me.
Checkout the snapshot.
Attachments:
xyplot.JPG 7 KB -
How to print a 3D Graph with Labview 5.1?
I would like know if i can print a 3D Graph with Labview 5.1.
From NI knowledgebase: "LabVIEW 5.1 includes a 3D Graph control in the Full and Professional Development Systems. Visit the LabVIEW Product page for more information on ordering or upgrading to LabVIEW 5.1. The LabVIEW 5.1 Base package includes a demo version of the 3D Graph control."
Hope this helps -
How to Send Multiple Plot XY Graph from LabVIEW to Microsoft Excel
The link below describes exactly what I would like to do, however the link to the solution/work around does not work.
Has anyone got an alternative solution?
http://digital.ni.com/public.nsf/allkb/CFD30D5E9C01AB5386256CFB0082AF3EPlease check the link again as it seems to be working fine now.
How to Send Multiple Plot XY Graphs from LabVIEW to Microsoft Excel:
http://digital.ni.com/public.nsf/allkb/CFD30D5E9C01AB5386256CFB0082AF3E
The standard Excel Insert Graph.vi cannot insert multiple XY Graphs to Microsoft Excel, so you will need to use the Report Generation Toolkit for Microsoft Office. You will find a link to an example program at the bottom of the page. I have also attached it below.
Attachments:
example.zip 35 KB -
Réception sur Labview de données par Liaison série depuis un PIC18F458
Bonsoir à tous,
Dans le cadre d'un projet ingénieur, j'ai dû développer une application sous un PIC18F458. A présent, j'ai des mesures que je souhaite pouvoir afficher sous Labview par la liaison série du PIC.
J'ai donc utilisé les exemples données sous Labview (8.4), et cela me renvoi quelques résultats... Le problème est que dans l'exemple, l'afficheur renvoi une chaîne de caractère. Pour ma part, ce sont des mesures que je vais afficher, donc j'ai modifier cet partie en ajoutant une convertion en "tableau d'octet" pour pouvoir commencer a visualiser quelque chose de cohérent.
N'y a t-il pas un autre moyen que d'afficher un tableau d'octets?
De plus, je souhaite envoyé plusieur mesures différentes sous labview, je souhaiterais savoir comment les réceptionner correctement, comment savoir laquelle est ma mesure de tension ou de courant par exemple?
Merci d'avance de votre temp,
Bien cordialement,Merci,
J'ai travailler durant toutes la journée sur la mise en protocole pour l'envoi de différente valeur sur labview, mais j'éprouve des difficultés à le faire.
Tout d'abord, sur la partie PIC, comment définir ce protocole? (Envoi de plusieur trames consécutives, avec un identifiant de départ par exemple?)
Et sur labview, comment réussir à découper ces trames et savoir quel est la bonne?
Si quelqu'un aurais des idées, cela m'aiderais beaucoup.
Ci-joint ma fenêtre labview.
PS : mon code PIC simplifié est le suivant :
OpenUSART (USART_TX_INT_OFF & USART_RX_INT_OFF & USART_BRGH_HIGH & USART_EIGHT_BIT & USART_ASYNCH_MODE, 64);
while(1)
while(BusyUSART());
WriteUSART(totalSums); //variable totalSums
delay(); //(0,5 seconde)
while(BusyUSART());
WriteUSART(accumulator); // variable accumulator
Merci d'avance,
Pièces jointes :
Labview.PNG 78 KB -
Affichage d'une image traité par matlab sur labview
Bonjour!!
je veux faire un traitement d'image avec matlab et afficher les resultats sous Labview . j'ai essayer la formula node de matlab dans la palette mathematics mais l'affichage se fait toujours sur matlab comment je peux l'afficher sur labview ??
vous trouver ci-joint le programme utiliser .
% Load jpeg files
orgImage = imread('Pixel.jpg', 'jpg');
figure(1); imshow(orgImage);
% 2D FFT
fftImage = fftshift(fft2(orgImage)); % 2d fft
ampImage= abs(fftImage);
figure(2); imshow(ampImage, [0 10000 ]);
% Convolution (low-pass filtering)
filter = fspecial('gaussian',[10 10], 4); % gaussian kernel
filterImage = conv2(orgImage, filter); % convolution
figure(3); imshow(filterImage, [0 250]);
% 2D FFT of filtered image
fftFilterImage = fftshift(fft2(filterImage));
ampFilterImage= abs(fftFilterImage);
figure(4); imshow(ampFilterImage, [0 10000 ]);
Attachments:
1335097296331.jpg 59 KBHello aziz-be,
You may find quicker responses in the french forum.
http://forums.ni.com/t5/Discussions-de-produit-de-NI/bd-p/4170
Regarding your question. The Matlab Scipt Node uses activeX to access an api that calls into the Matlab engine. Thus any figure generation would occur on the Matlab side of things. What you could try doing is converting the figure to an image, converting the image to an array, and bringing that array into labview and converting it into a LabVIEW image type which you could then display inside of LabVIEW. This is a rather convoluted way of displaying a figure on the front panel inside of LabVIEW though. You may find it much easier to do what you are trying to accomplish with the MathScript Node rather than the Matlab Script Node.
figure (MathScript RT Module Function)
http://zone.ni.com/reference/en-XX/help/373123B-01/lvtextmath/msfunc_figure/
NI LabVIEW MathScript RT Module
http://www.ni.com/labview/mathscript/
David A
National Instruments
FlexRIO Product Support Engineer -
Camera kinect myRIO sur labview
j'ai un problème au niveau de l'utilisation d'une camera kinect avec la carte myRIO 1900 sur LABVIEW . lorsque j'envoie le code a la carte myRIO des erreurs s'apparaissent.j'aimerais bien avoir un support qui me guidera pour bien utiliser la camera kinect avec la carte myRIO. merci
Bonjour,
Aviez-vous essayé ces liens :
https://decibel.ni.com/content/docs/DOC-31239
https://decibel.ni.com/content/docs/DOC-34889
Cordialement
Samuel G. | Application Engineer Team Leader
Certified LabVIEW Developer
National Instruments France
#adMrkt{text-align: center;font-size:11px; font-weight: bold;} #adMrkt a {text-decoration: none;} #adMrkt a:hover{font-size: 9px;} #adMrkt a span{display: none;} #adMrkt a:hover span{display: block;}
Été de LabVIEW 2014
12 présentations en ligne, du 30 juin au 18 juillet -
Utilisatio​n des fonctions trigo sur labview
Bonjour,
je fais de l'acquisition de données sur labveiw et je suis encore débutant!! j'ai un problème avec l'utilisation des fonction trigonométrique sur labview car ca me renvoie tout et n'importe quoi. j'ai fait un simple VI pour vérifier le fonctionement de la fonction sinus et arcsinus et quand j'entre par exemple j'entre la valeur 30 ca me donne en sortie du sinus -0.98 alors qu'on sait tous que le sin 30°=1/2 et pire encore quand je reprend ces -0.98 que j'entre dans la fonction arcsin ( la réciproque) je n'obtiens plus les 30 de depart mais -1.42 :/ j'aimerais savoir savoir le truc que je ne capte pas. Car pour moi tous ces résultats sont illogique!!!
Merci
Résolu !
Accéder à la solution.Bonjour,
Il faut utiliser des angles en radians.
Cordialement,
Micaël DA SILVA -
Compteur décompteur sur labview pr signal triangulaire sur carte PCI-6024E
Nous savons qu'il faut utiliser un compteur décompteur pr former un signal triangulaire sur la carte PCI-6024E, existe-t-il un vi sur labview préréaliser qui nous permettrai de générer un tel signal. Ou alors pourriez vous nous expliquer comment réaliser ce vi.
meciIl exitse bien un VI qui permet de générer des signaux triangulaires.
Il se situe dans la palette Analyse >> génération de waveforms >> waveform Triangulaire.
Bonne continuation -
Driver d'une table traçante sur Labview
Bonjour,
je suis à la recherche de n'importe quelle table traçante ayant driver sur labview, en fait je travaille sur un projet pour commander des instruments de mesure dont les reponses seront simulées sur une table traçante, alors j'ai besoin du driver de cette dernière.
j'ai cherché sur net, labview, mais en vain.
si quelqu'un s'il vous plait, pourrait m'aider...Merci beaucoup cher Z'Atari,
Une table traçante est un outil de
dessin industriel. Elle se compose d'une table horizontale et d'un porte-stylo
motorisé, commandé par ordinateur, tu trouveras ci-joint une photo d'une table traçante, bein ce que je désire faire est de commander une table par ordinateur sous labview, mais j'ai pas trouvé de table commandable sous labview.c'est pour cela que j'ai besoin d'un driver comme si je comandais un oscilloscope,...je sais pas si je m'explique bien
Attachments:
table-tracante-xy-din-a3-100cms-49377n0.jpg 8 KB -
Problème affichage sur graphe XY[Labview 8.5]
Bonjour à tous,
Je réalise l'acquisition de signaux à partir d'une application de test qui me fournit les coordonnées (X,Y)
des signaux (voir fichier texte joint). Les coordonnée en X sont données en temps absolu, c'est à dire le nombre
de seconde écroulé depuis le 1er Janvier 1904. Malheureusement lors de l'affichage sur un graphe (X,Y), je constate
qu'une partie du graphe n'est pas utilisé! ( Partie représenté en jaune sur l'image jointe) Je ne comprend pas pourquoi!
Pourriez vous m'éclairer???
Cordialement.
S.
Résolu !
Accéder à la solution.
Pièces jointes :
graphe.JPG 63 KBBonjour,
Malheureusement, je ne peux pas vous founir le code associé au fichier pour des raisons de confidentialités
d'une part. Et d'autre part, il ne vous sera pas possible de l'exploité sans l'environnement associé (composé de nombreux VIs).
Cordialement.
S.
Pièces jointes :
VIgraphe.JPG 31 KB
Maybe you are looking for
-
I am getting an error message if I try to sign into or authorize my iTunes account
The error message I am getting is "We could not complete your iTunes store request. The file or directory is corrupted or unreadable. There was an error in the iTunes store. Please try again later." I don't know what this means or how to fix it. It h
-
how can i get my facetime to start working again
-
Jdeveloper IDE bug with Soa 11g PS1 ejb adapter with uri and jndiName
Hi, When you use the EJB adapter as a reference in Soa suite 11g PS1 and you provide the jndiname then jdev put its wrong in the binding.ejb and use the uri attribute instead of jndiName <reference name="EmployeeReferenceService" ui:wsdlLocation="HrE
-
Podcasts won't stay in the order I choose
This is related to another thread I saw on here. But my issue is a little different so I started another one. I have a 2nd generation shuffle and updated versions of iTunes and Mac OS X (well almost... 10.4.9). I have reset the iPod several times and
-
The bookmarks plug in seems to be highly disorganized and difficult to access in an organised manner
1. When I sort the bookmarks folder I cannot get it to place all of the created folders at the top of the sort list and the general bookmarked pages below the list of sorted folders. I would have thought that this would be a very basic requirement of