Trouble Booting up when upgrade to 8GB ram on the Macbook Pro 13 Mid-2010 edition

I have the right specs(two )Size: 4 GB Type: DDR3 Speed: 1067 MHz and it freeze when booting. but when I take one out and put one 4 GB and a 2 GB Ram, it boots and works fine at 6GB, I even change to a different more expensive brand ram and its the same issue, works at 6GB and not 8GB, Can someone help me.

First off make sure, again, that you have the right memory -- 204-pin PC3-8500 (1066 MHz) DDR3 SO-DIMM. If you do, swap out the the two modules. Place the 2G stick where the 4G was and put the 4G where the 2G was. Check your system RAM. If you do not have 6G then the slot where the 4G stick is is bad. If you have 6G, then swap out the two 4G sticks. If you now do not have 6G then the second 4G stick is bad. If you get 6G then we will try something else.

Similar Messages

Macbook pro mid 2010 15" 16 GB ram upgrade possible?

I recently purchased RAM from Crucial.com for 8 GB and after having researched a bit online I've heard of users upgrading to 16 GB. Is this true?
Here are the specs of my cpu:
MacBook Pro 15" Mid 2010
OSX Yosemite 10.10.1
Memory 8 GB 1067 MHz DDR3
2.53 GHz Intel Core i5
Can anyone give me insight? I'm not very computer literate, but could use all the advice I could get. Thank you kindly

Good morning ipodsmut,
The MacBook Pro mid 2010 model supports up to 8GB of RAM. See this Apple specifications article -
MacBook Pro (15-inch, Mid 2010) - Technical Specifications
Thanks for using Apple Support Communities.
Best,
Brett L

I have a 15' Macbook Pro, mid 2010 running Mavericks. I want to upgrade the hardware by increasing the RAM to 8GB and replacing the HD for a SDD one. What would be the best way to install mavericks on the new HD? I have the original OS X CD.

I have a 15' Macbook Pro, mid 2010 running Mavericks. I want to upgrade the hardware by increasing the RAM to 8GB and replacing the HD for a SDD one. What would be the best way to install mavericks on the new HD? I have the original OS X CD.
From what I read, I have 2 choices: 1. to install OSX and then upgrade to Mavericks, but I'm not sure if this would be possible (to upgrade directly from OSX to Mavericks); and 2. to use a software called Super Duper.
I wouldn't like to have to use a third party software to do this, so the question is: is there a better way to install directly the Mavericks not having to use a third party software?

Install the new drive in the computer.
Install the old drive in an external USB or Firewire enclosure.
Boot the computer from the Recovery HD on the external drive.
Use Disk Utility to partition and format the new internal drive.
Clone your external drive to the internal drive.
How to replace or upgrade a drive in a laptop
Step One: Repair the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Step Two: Remove the old drive and install the new drive. Place the old drive in an external USB enclosure. You can buy one at OWC who is also a good vendor for drives.
Step Three: Boot from the Recovery HD on the external drive. Restart the computer and after the chime press and hold down the OPTION key until the boot manager appears. Select the icon for the Recovery HD then click on the downward pointing arrow button.
Step Four: New Hard Drive Preparation
1. Open Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your new hard drive (this is the entry with the
      mfgr.'s ID and size) from the left side list. Note the SMART status of
      the drive in DU's status area. If it does not say "Verified" then the drive
      is failing or has failed and will need replacing. Otherwise, click on the
      Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from
      the drop down menu to one. Set the format type to Mac OS Extended
      (Journaled.) Click on the Options button, set the partition scheme to
      GUID then click on the OK button. Click on the Partition button and
      wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the
      drive entry) from the left side list. Click on the Erase tab in the DU main
      window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the
      Options button, check the button for Zero Data and click on OK to
      return to the Erase window.
6. Click on the Erase button. The format process can take up to several
      hours depending upon the drive size.
Step Five: Clone the old drive to the new drive
1. Using Disk Utility still opened.
2. Select the destination volume from the left side list.
3. Click on the Restore tab in the DU main window.
4. Check the box labeled Erase destination.
5. Select the destination volume from the left side list and drag it to the
      Destination entry field.
6. Select the source volume from the left side list and drag it to the
      Source entry field.
7. Double-check you got it right, then click on the Restore button.
Destination means the new internal drive. Source means the old external drive.
Step Six: Open the Startup Disk preferences and select the new internal volume. Click on the Restart button. You should boot from the new drive. Eject the external drive and disconnect it from the computer.

Apple Unibody 13.3" MacBook Pro (Mid-2010): 4GB vs. 8GB DDR3 1066MHz Memory (RAM).

Apple Unibody 13.3" MacBook Pro (Mid-2010): 4GB vs. 8GB DDR3 1066MHz Memory (RAM).
1. About my Mac.
     Processor: Intel® Core 2 Duo (2.66GHz)
     Memory (RAM): 4.00GB DDR3 1066MHz (2 x 2.00GB)
     Hard Drive: 320GB 5400RPM (Apple Stock HD)
     Graphics: NVIDIA GeForce 320M (256MB)
     Operating System: Mac OS X Lion (10.7.1)
2. My concerns/questions
     For quite some time now, I've been planning to upgrade the memory (RAM) of my MacBook Pro from 4.00GB (Apple Stock) to 8.00GB. In terms of "FASTER BOOT TIMES, IMPROVED RESPONSIVENESS (OPENING and CLOSING PROGRAMS, FILES & ETC.), SMOOTHER GRAPHICS, ABILITY TO OPEN MORE PROGRAMS SIMULTANEOUSLY AND OVERALL IMPROVEMENT IN PERFORMANCE", does it really make a BIG difference?
     If ever I am going to pursue this upgrade, should I let Apple do the upgrade or buy the parts and do it myself?
     If I am going to buy the parts and install it myself, what brand do you recommend? Crucial, Kingston, OWC & etc.?
     Why does Apple charge so much for memory (RAM) upgrades? Is the memory module they are using any special compared to the ones we can find in Amazon (Crucial, Kingston, OWC & etc.)?
Thanks for helping me out with my concerns.

I recommend OWC RAM because it's reasonably priced and OWC's support is great if you ever need it. I recommend installing the RAM yourself because it's dead simple. There is no good reason for anyone ever to pay Apple's prices for RAM.
I don't think you will see faster boot times with more RAM, but that shouldn't be a concern, because there's seldom any need to shut down or restart a MBP. Just put it to sleep when you aren't using it, unless you won't use it again for more than two or three days. Opening and closing programs won't benefit significantly from more RAM either, but when running multiple large programs at once, you will see a significant improvement in their performance. It's well worth the small investment ($65) to upgrade from 4GB to 8GB.
http://eshop.macsales.com/shop/memory/Apple_MacBook_MacBook_Pro/Upgrade/DDR3

Installing 8GB ram on MacBook Pro (Mid 2010)

Hi, I have bought 8GB(2*4GB) ram to install on my macbook pro, when I install both I get a black screen but when installing one or the other with one of the original ram they both work. What can I do to fix this problem??

Topher Kessler California
Re: Installing 8GB ram on MacBook Pro (Mid 2010)
Jun 1, 2013 8:00 AM (in response to emiliosh)
When you install RAM, reboot your computer with the "D" key held down (or the Option-D keys). These will load the Apple Hardware Tests.
With these tests open, check the box for the extended memory test, and then start the test. This will have the system thoroughly test the RAM for errors.
In your case, it appears you may have a bad set of RAM modules, but you can check them using the method above.
When you have them paired with your original RAM, how much memory does the system report as being available when you select About This Mac in the Apple menu? If you are using Lion or Mountain Lion, then in this panel click "More Info" and then select the "Memory" section, and see what the system reports as being installed.
Is this RAM test necessay with every upgrade of memory or just if you have problems after the upgrade
Thanks

HT202008 I am having issues with my Window 7 on boot camp. My hardware is Macbook Pro Mid 2010 model and working on OS X 10.9.5. Recently I went to windows 7 to do a system upgrade but failed and was told to update the bootcamp drivers.

I am having issues with my Window 7 on boot camp. My hardware is Macbook Pro Mid 2010 model and working on OS X 10.9.5. Recently I went to windows 7 to do a system upgrade but failed and was told to update the bootcamp drivers. I installed boot camp5 but seem to be the wrong version and change to boot camp 4 which was updated okay. However I still cannot do the updates. Can someone advice me please? Thank you!

Please see Boot Camp: System requirements for Microsoft Windows operating systems - Apple Support for the appropriate version of drivers related to the specific version of Windows 7.
MacBook Pro
(13-inch, Mid 2010)
4
4
DVD
DVD
DVD
MacBook Pro
(15-inch, Mid 2010)
5
5
4
DVD
DVD
DVD
MacBook Pro
(17-inch, Mid 2010)
5
5
4
DVD
DVD
DVD
Be careful with Windows Updates, especially driver updates. Standard WHQL drivers can cause problems.

Unable to open Bootcamp install of Vista after upgrading MacBook Pro / Mid 2010 to OS Mavericks

Dear Community,
I am unable able to boot the Windows Vista install (via Boot Camp) on my MacBook Pro / mid 2010 after upgrading to OS Maverick.
Any idea about how this problem can be solved (I don't want to purchase Windows 7 and I don't want to purchase a virtual machine)?
Many thanks for your support!
Regards,
PSeguro

Hello 88,
I haven't resized / modified anything since installing Vista on my System. The problem must have incurred when upgrading from Snow Leopard to Maverick.
by the way:
I (just) found out that Windows Vista is booting (automatically) when I insert my original "Mac OS X Install DVD" / 10.6.3 (or my "Applications Install DVD") before starting the MacBook. It will - hwr - not boot without above DVDs in the tray...
sudo fdisk /dev/disk0:
Disk: /dev/disk0          geometry: 60801/255/63 [976773168 sectors]
Signature: 0xAA55
         Starting       Ending
#: id cyl hd sec - cyl hd sec [     start -       size]
1: EE 1023 254 63 - 1023 254 63 [         1 -     409639] <Unknown ID>
2: AF 1023 254 63 - 1023 254 63 [    409640 - 510699696] HFS+
3: AB 1023 254 63 - 1023 254 63 [ 511109336 -    1269544] Darwin Boot
*4: 07 1023 254 63 - 1023 254 63 [ 512378880 - 464394240] HPFS/QNX/AUX
sudo gpt -r -vv show disk0:
gpt show: disk0: mediasize=500107862016; sectorsize=512; blocks=976773168
gpt show: disk0: Suspicious MBR at sector 0
gpt show: disk0: Pri GPT at sector 1
gpt show: disk0: Sec GPT at sector 976773167
      start       size index contents
          0          1         MBR
          1          1         Pri GPT header
          2         32         Pri GPT table
         34          6
         40     409600      1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
     409640 510699696      2 GPT part - 48465300-0000-11AA-AA11-00306543ECAC
511109336    1269544      3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
512378880 464394240      4 GPT part - EBD0A0A2-B9E5-4433-87C0-68B6B72699C7
976773120         15
976773135         32         Sec GPT table
976773167          1         Sec GPT header
Regards,

BootCamp 5.0 error on 13" MacBook Pro Mid-2010: "Installation Error. Boot Camp x64 is unsupported on this computer model"

Installing Boot Camp 5.0.5033 (downloadable at http://support.apple.com/kb/DL1638) on Windows 8 x64 on 13” MacBook Pro Mid-2010 using BootCamp\setup.exe, I get the following message: “Installation Error. Boot Camp x64 is unsupported on this computer model”.
According to http://support.apple.com/kb/HT5634, Windows 8 x64 is not supported by Boot Camp 5 on 13” MacBook Pro Mid-2010 .
Previous version, Boot Camp 4.0, causes bluescreens on Windows 8 (https://discussions.apple.com/message/20131524#20131524).
Fortunately, it might be still possible to employ updated Boot Camp by launching “msiexec /i BootCamp.msi” from BootCamp\Drivers\Apple folder using administrative command prompt (http://technet.microsoft.com/en-us/library/cc947813%28v=WS.10%29.aspx).
However, new Boot Camp 5.0.5033 does not contain all the drivers for 13” MacBook Pro Mid-2010. E.g. driver for NVIDIA nForce System Management Controller (labeled Other devices/Coprocessor in Control Panel) and NVIDIA nForce PCI Systems Management (labeled Other devices/SM Bus Controller in Control Panel) must be obtained at Drivers\NVidia\NVidiaChipset64 in older Boot Camp 4.0 (downloadable at http://support.apple.com/kb/DL1634)
According to Microsoft (http://windows.microsoft.com/en-US/windows-8/system-requirements), the MacBook Pro config (Intel Core 2 Duo P8600 2.4GHz, 4GB RAM) exceeds Windows 8 x64 hardware requirements. Windows Experience Index for this laptop is approx. 5.1 (http://windows.microsoft.com/en-US/windows-8/what-windows-experience-index).
Does anybody know, is there any technical reason why Windows 8 x64 is not supported by Boot Camp 5 on 13” MBP Mid-2010?
Is there a specific hardware/firmware deficiency in this MacBook model, incompatible with Win8? Maybe NVIDIA refused to provide Win8-compatible drivers for its chipset components (GeForce 320M graphics card though is still supported by latest notebook drivers available at www.geforce.com)?

Thanks for the detailed explanation! If MacBook supports AHCI/SATA only in native “UEFI mode”, while reverting back to PATA/IDE in legacy “BIOS mode”, then it could make perfect sense to use UEFI to make sure that technology like Native Command Queuing (NCQ) is employed, as it may give noticeable performance improvements for certain operations: www.happysysadm.com/2012/12/intel-g530-nas-performance-part-3.html. I wonder how do you get Windows 8 x64 with EFI bootloader installed on MacBook?
Simply choosing EFI Boot (“Some EFI platforms support both UEFI and BIOS firmware. On some of those systems, it is not always clear if the default DVD boot option is an EFI or BIOS boot option. On these systems, using the EFI shell command may be required. If you do not specifically start Windows Setup by using the EFI boot entry, the default firmware boot entry for BIOS may be used. If Windows Setup starts in BIOS mode on a combined EFI/BIOS system, the ESP and MSR partitions are not created.”) from Win8 x64 DVD when installing on blank HDD would yield “The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed" message. Also, if the hard drive was not in SATA mode during Windows installation, registry tweaking may be required before switching from PATA to SATA. Do you do registry tweaking and EFI bootloader configuration manually after a copy of Windows was installed in its dedicated partition in a regular way?

After some advice, I am new to Apple and looking to purchase either the MacBook Air 13inch with 256GB and 8GB mem or the MacBook Pro 13inch with retina 256Gb and 8GB mem. I am an assistant principal in a primary school and also studying my masters

After some advice, I am new to Apple and looking to purchase either the MacBook Air 13inch with 256GB and 8GB mem or the MacBook Pro 13inch with retina 256Gb and 8GB mem. I am an assistant principal in a primary school and also studying my masters at university. I don't play computer games and I don't watch movies. I do store photos and videos of my kids and music on iTunes. I also like browsing the net with numerous windows open, check email etc. I am really wanting long battery life as I do a lot of my work on the couch - not close to a PowerPoint. Would the air do the trick or will it soon be outdated as Apple move towards retina display? Both air and pro seem very thin - almost the same? And not much difference in weight either so both very portable which is also a necessary requirement. Just can't help dreaming about that 12 hour claimed battery life. Any helpful advice/opinions, very much appreciated. Thanks

It's not likely that you'll get 12 hours in reql life. Those benchmarks are set under very strict controlled conditions. Kind of like mileage per gallon claims on cars. If 16GB of ram is an option at all I'd highly recommend you get that. As far as storage 256GB isn't alot, consider storing some things on an external thunderbolt real

My MacBook Pro mid 2010 was upgraded to mountain lion os x and then my wifi started saying no hardware installed

My MacBook Pro mid 2010 was upgraded to mountain lion os x and then my wifi started saying no hardware installed

Hello Harrisonhcue,
I would be concerned too if I was getting the message "no hardware installed" when trying to use Wi-Fi on my MacBook Pro. For a message like this, I recommend resetting your System Management Controller (SMC) and NVRAM.
Resetting the SMC on portables with a battery you should not remove on your own
Note: Portable computers that have a battery you should not remove on your own include MacBook Pro (Early 2009) and later, all models of MacBook Air, and MacBook (Late 2009).
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC.
You can find the full article here:
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/ht3964
Resetting NVRAM / PRAM
Shut down your Mac.
Locate the following keys on the keyboard: Command (⌘), Option, P, and R. You will need to hold these keys down simultaneously in step 4.
Turn on the computer.
Press and hold the Command-Option-P-R keys before the gray screen appears.
Hold the keys down until the computer restarts and you hear the startup sound for the second time.
Release the keys.
You can find the full article here:
About NVRAM and PRAM
http://support.apple.com/kb/ht1379
Thank you for using Apple Support Communities.
Best,
Sheila M.

What's up with the screw job on the Airplay mirroring? Macbook Pro (mid 2010) too old to have feature included in Mountain upgrade? Bull!

what's up with the screw job on the Airplay mirroring? Macbook Pro (mid 2010) too old to have feature included in Mountain upgrade? Bull!

Please read:
http://arstechnica.com/apple/2012/07/mountain-lion-airplay-mirroring-v-airparrot -fight/
Mountain Lion's integrated AirPlay mirroring support only works with the following Mac models:
iMac—Mid 2011 or newer
Mac mini—Mid 2011 or newer
MacBook Air—Mid 2011 or newer
MacBook Pro—Early 2011 or newer
If your Mac isn't on that list, your won't ever see an AirPlay option in Mountain Lion's menubar.
What separates these Macs from other Mountain Lion-compatible machines is that these are the only models that have support for Intel's QuickSync technology. What confirmed this requirement for me was the fact that my Retina MacBook Pro switched to integrated Intel HD4000 graphics even when otherwise running on the discrete NVIDIA GT 650M GPU. No matter what you are doing or what resolution you are running, AirPlay Mirroring in Mountain Lion requires an integrated Intel HD3000 or HD4000 graphics processor and its QuickSync technology to work, full stop.

Just upgrade my MacBook Pro Mid 2010 to Mountain Lion and tried to connect with Apple TV 3th gen. through Airplay and couldn't mirrorring video on my LG Smart TV screen. Just paid US 99.00 for Apple TV plus US 19.99 to Mountain Lion for nothing @?$%

Just upgrade my MacBook Pro Mid 2010 to Mountain Lion and tried to connect with Apple TV 3th gen. through Airplay and couldn't mirrorring video on my LG Smart TV screen.
Just paid US 99.00 for Apple TV plus US 19.99 to Mountain Lion for nothing @?$%& !!!!
Back again to mini display to hdmi cable.
could you help me????

It is stated that mirroring requires recent hardware (2011 or later)
http://support.apple.com/kb/ht5404
However you can still use 3rd party solutions like Airparrot which do it via software

I've a MacBook Pro Mid 2010 with OS X Lion 10.7.2. and when i try to update my software it says you are up to date in fact 10.7.3 is out.

I've a MacBook Pro Mid 2010 with OS X Lion 10.7.2. and when i try to update my software it says you are up to date in fact 10.7.3 is out.

Actually, the Software Update has been replaced by the Combo Update.

What type of ram does the MacBook Pro 15" use?

What type of ram does the MacBook Pro 15" use? Is it the same as the 13"?

13 and 15-inch MacBooks Pro use the same RAM type, but it depends on the model. See > http://support.apple.com/kb/ht1270

Trouble to connect to wireless G routers after installed the latest update 10.10.2 . Anyone with the same problem? Please help Apple support team!! Macbook Pro mid 2010. PS.: Only with wireless G routers, the rest are fine (N, B...)

Trouble to connect to wireless G routers after installed the latest update 10.10.2 . Anyone with the same problem? Please help !!! Macbook Pro mid 2010. PS.: Only with wireless G routers, the rest are fine (N, B..., and both radio bands)

Trouble to connect to wireless G routers after installed the latest update 10.10.2 . Anyone with the same problem? Please help !!! Macbook Pro mid 2010. PS.: Only with wireless G routers, the rest are fine (N, B..., and both radio bands)

Trouble Booting up when upgrade to 8GB ram on the Macbook Pro 13 Mid-2010 edition

Similar Messages

Maybe you are looking for