Trouble connecting MCC USB 1208FS to Labview 10.0

I have trouble in connecting MCC USB 1208FS with Labview. I can see that the MCC card is detected through the InstalCal software of MCC. I am not able to see it on Labview interface. How to confirm that MCC device is connected with Labview. I have installed the latest MCC software and have Universal Library(UL) installed. I could see the UL functions listed in the Labview "functions>user libraries>MCC data acquisition".

Duplicate Post

Similar Messages

Trouble connecting to USB Harddisk

Hi all,
I recently bought an AEBS to set up a wireless network for my Windows PC and Laptop. So far so good, both wintel machines can connect to internet, and both can print to the USB printer hooked to the AEBS.
I also connected a USB harddisk to the AEBS, but only my laptop can connect to it. My workstation fails and keeps telling me that the supplied password is incorrect, no matter what I try: client access or disk access.
*One more thing I like to know:*
How can I create a share on my Desktop that will be visible for my laptop. I used to have this when I had everything wired with a simple router. But now I have it all wireless, and I cannot figure out how to do this (sharing directories and/or disks) because Windows does not show the wireless network in "available network places" (or whatever this is called).
Thanks

Questions not valid anymore. Dropped the Windows PC and am now completely Mac orientated

Trouble connecting to USB storage device on WRT160NL with Mac 0S X 10.5

I recently purchased a WRT160NL router with usb link for NAS storage and media server capabilities. Internet connectivity works fine and I can log in to change router settings with no probelm, but I can not connect to the usb drive that is connected to the router, when using my Mac with OS X 10.5. My XBox360 picks it up as a media server with no problems.
I followed the instructions on Linksys.com
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=16796
It appeared to work the first time, but then I ejected the network connections, admin and guest. It has not worked since.
I open my browser and paste smb://192.168.1.1 into the address bar and hit enter. Then I get an error message that reads:
Connection failed
There was an error connecting to the server. Check the server name or IP address and try again.
If you are unable to resolve the problem contact your system administrator.
I select ok and get another error message that says:
Could not connect to the server because the name or password is not correct.
I know that, according to Linksys, the next step is to put in name and password, but I never get that option.
I have also double checked the IP address to make sure it is correct, which it is.
I just want to be able to read and write media to the network drive from my laptop and play the media from my xbox360.
Can anyone help?

Thank you for your response.
So, when I go to http://192.168.1.1 I have no problem finding the drive under the storage tab. When going deeper into the settings it also shows all of the contents of that drive. So it is definitely connected to the router. Though I still cannot access it through smb://192.168.1.1.
And yes, the drive shows up as it should if it is plugged directly into my computer.
I powered the router down for about 10 or 15 minutes and powered it back up. Still having the same problem.
I believe the problem is with OS X 10.5 Leopard. The first time I tried this, when it appeared to work, I checked the box for remember my password. At the time it was still the default password. I changed the password since then, yet now I am not given an option to put in the password since Leopard tries to log me in automatically. I cannot find a way to undo that auto log in.
Of course I am not absolutely certain that is the problem, but if anyone knows how to undo the auto log in that might help.
Any ideas?

Connecting canberra osprey mca to LabVIEW

Hello all,
Could anyone show me the way to connect an USB device to LabVIEW interface? The device is Osprey, an MCA manufactured by Canberra company.
I have a driver of this MCA but I dont know how to connect it with LabVIEW. http://www.canberra.com/products/radiochemistry_lab/digital-signal-processing.asp
Moreover, what's version of LabVIEW do I need to solve this problem? (I just have LabVIEW 8.5)
Thank you all.

You need the Canberra SDK for Osprey. A quick review of the documentation reveals that the SDK includes COM, .NET and DLL interfaces.
With your LabVIEW version you should be able to use at least one of them.
Ask Canberra for details.
Paolo
LV 7.0, 7.1, 8.0.1, 2011

Are there LabVIEW drivers for the MCC USB-501 temperature logger

I am looking to purchase the MCC USB-501 and use it to acquire the ambient temperature on an event driven basis. The data logging portion is something I am interested in, I just want to have my application acquire the tempture when a certain event occurs. Does anyone have any LabVIEW drivers for this device?

I don't know what you mean by using a logger that collects data on an "event driven basis".
It is nifty little device, but it basically does one thing. It logs data. You load the software, configure it for when to start an how often to log data, unplug it, and put it where you want to log the temperature. When you're done, you get it plug it back in and download the data that was logged.
There is no way to configure it to react to events. It's possible that a LabVIEW driver exists for this, but all it would do is provide an alternate way of downloading the data instead of using the software that comes with it. It is not an immediate or interactive piece of hardware like a normal data acquisition card would be.

Connecting Agilent DSO3062A Oscilloscope with LabVIEW using USB

I am trying to connect Agilent DSO3062A Oscilloscope with LabVIEW using USB but the device is not recognized by MAX. I have installed the drivers for scope and it works fine with the scope software. The problem is LabVIEW dosen't recognize the scope. Please tell me the procedure of setting up the scope with LabVIEW 8.2. I am using Windows XP.

Hi there,
I think the issue is that the DSO3062A will not be recognized by LabView as a GPIB instrument through the USB connection. If you check out the 3000 series manual (http://cp.literature.agilent.com/litweb/pdf/D3000-97016.pdf) you'll notice on page 8 it says you can't use the USB for programming, it can only be used with their scope software. You need the N2861 module installed on the back to connect via GPIB, and then a GPIB interface to your computer. I hope that helps.
-jmart

How to aquire data of Bluetooth device connected to USB port by using LABVIEW?

I am using LabVIEW2010 and want to acquire data of Bluetooth device which is connected to USB port while i am using OS xp3
THANKS

Does it have a driver to use it as a serial port?
Say hello to my little friend.
RFC 2323 FHE-Compliant

USB-6009 with Labview 2014 on Windows 8.1

Hi,
I have trouble connecting USB-6009 OEM with my new laptop with windows 8.1. My USB-6009 OEM device is not shown up in NI Max. So when I check Device Manager, there is a question mark on "NI USB-6009 OEM FW". I tried to install Labview 2011 but still the same. When I tried to choose the driver in Device Manager manually, I can only find NI-VISA driver as the closest one. It is still not working when I open DAQmx to check my card. It is still not detected in NI Max and anywhere within labview. When I used NI-VISA driver, and try to connect the device in NI Max, I get timeout error. I think I need to see NI-USB driver instead of NI-VISA driver. Any help would be appreciated.
Cheers,

Hi Thoo,
You may also want to try reinstalling the DAQmx 14.5 driver first. DAQmx 14.5 is supported on Windows 8.1. Some of the driver files may have been corrupted and reinstalling the driver may solve the issue. If not, using the DAQmx Base driver could be a good option as Dennis suggested.
Thanks,
Frank
Application Engineer
National Instruments

When iPhone 5s is connected via USB no audio is heard

Hi There -
I've seen older threads on this issue but I don't think I've really come across any solutions. My issue started yesterday; now before reading further I have to ask that you please keep in mind that I did perform the latest upgrade on my iPhone a bit earlier in the day.
When I connect my iPhone to my vehicle sync system and announce that I'd like to connect via USB, the voice recognition repeats my request and then the music on my iPhone shows to be playing on the display in my vehicle. The problem is that though the music appears to be playing and the minutes played are being displayed there is no audio coming through. When I switch to the Bluetooth Audio option all sound comes through.
Now, as a 2nd test, we connected my sons iPhone 5s via USB (he has not taken the latest update on his iPhone) and the same issue happens with his. Voice recognition changes to the USB format as requested, music appears to be playing but no audio is heard. When we change his phone to Bluetooth Audio the audio comes through nice and clear.
I'm not entirely convinced the update caused the issue so I wanted to put this out there to see if anyone has run into this and were able to actually resolve the issue.
I know the USB cable is working fine because when I do plug it into either phone the phone makes the little connection sound and pops up a brief battery percentage box. I also know the cable is working because when we announce USB as our audio of choice the system recognize USB via the iPhone.
One other thing I tried looking for was the option on the phone to switch from Docked to Synch - I know on my iPhone 4 I was able to switch back and forth through iTunes and would also have the option if I tried to watch anything via You Tube when connected to the dock; I cannot find this anywhere on the 5s when connected via USB.
Help is greatly appreciated!!!

I have had similar troubles with wifi.. some improvement removing BlackBerry desktop software & drivers & reinstalling after reboot... I used the same installer I had previously, but a fresh downloaded installer couldn't hurt...
10.3.1 SW .1779 OS .2726 WLAN .1.1 Radio .2727

Can I connect a USB 2 sound card to a Macbook equipped only with USB 3 ports?

Hello,
I just learned I might have to purchase a new Macbook because my USB ports are fried and I was looking at purchasing a refurbished Macbook pro from 2012:
http://store.apple.com/ca/product/FD101LL/A/refurbished-133-inch-macBook-pro-25g hz-dual-core-intel-i5
the only trouble is I make music with a MOTU Audio Express sound card, and it only has a USB 2 port and a bus-powered Firewire (which I don't like using since it hasn't been too reliable in the past).
http://www.motu.com/products/motuaudio/audio-express/summary.html
Unfortunately, it seems that the Macbook I'm looking into purchasing only has USB 3 ports, and I looked for info on USB 3->USB 2 adapters online and this simply doesn't seem to exist. The only info I managed to find on this subject was this little bit on the Apple website:
Can a USB 2 cable be used to connect a USB 3 device to my computer?
If the device end of the cable fits into the connector on the device, yes. However, because it has fewer wires, you won't get USB 3 speed and power may be limited to 500 mA.
does this mean that I can connect a USB 2 cable from the USB 2 port of the MOTU sound card to the USB 3 port on the Macbook? I'm OK with the power and the speed being limited to USB 2 power, I just want to make sure I can actually use my sound card with this new Macbook.
Thanks!

I think I'm understanding this a bit more now.
Here is the cable that I use:
http://www.amazon.ca/USB-Cable-Type-Male-Black/dp/B00183I7EE
The Type A part is the one that I'm currently putting into the Macbook and the Type B part goes in the sound card.
Would this work with a USB 3.0 port on the Macbook?
Thanks for your time and patience...

TS2756 I can no longer connect via USB/service missing

..& my iPhone does not show up on the list anymore. I can still use Wi-Fi, though. I would like to be able to use the USB connection again. Resetting the network settings doesn't help. BTW, I'm using it with my MacBook Pro running 10.7.5 and my iPhone has the latest iOS update as well.
When I first got the phone, I always used my internet connection via USB, but then it started giving me trouble. I tried all kinds of suggestions that I found here and it was a real crap shoot -- sometimes it worked, and sometimes not. Now it just won't work at all. I recently deleted my iPhone from the list of services thinking that the next time I plugged it in, it would recreated the service. It did not. So, I'm still using it as before: just connecting over Wi-Fi (the network is still available, it just doesn't show up in my list of services on the left-hand column under "network").
Anyone have any suggestions that they know will fix this?

Hi DaveX83 and welcome to the discussions.
A few things to try.
Press the reset button once on the back of your Extreme and let it restart. Check for proper operation.
If no help there, keep the ethernet cable connected, and open Airport Utility. Click on Manual Setup near the bottom of the pane. On the next screen click the Airport icon at the upper left of the pane, then click Wireless in the line just below that reads Summary - Time Capsule - Wireless - Access.
Check to see that your wireless is set up, security set up, passwords, etc. You may need to reconfigure your wireless settings again and update the Extreme to store them and restart.
Hope this helps.

Using usb-1208fs to control a hydraulic directional valve

Hi,
I am a PhD student, beginner in Labview. I am working on a project require controlling a hydraulic directional valve by using a USB-1208FS DAQ. I have an ultrasonic proximity sensor to sense the height differences of plants. The sensor output signal is analog voltage 0-10V, I managed to acquire signal from the sensor using the DAQ. I need to set different values of plants height depending on the sensor signal to actuate the hydraulic valve. The valve will control a hydraulic cylinder to move it up and down depending on the plants heights. I worked through a VI, but I don’t know how to generate two signals of 0-5V to operate the valve. For example, the range of plants height (0-6 inches) will switch ON one side of the valve to lower the cylinder down. The range of heights of (0-12 inches) will switch ON the other side of the valve to raise the cylinder up. Can anyone help me figure out how to do that. Thanks for your help!
Attachments:
Analog Input-Digital output.vi ‏68 KB

Hello Mazin,
The ULx driver comes with an analog output function. You can specify the channels the same way you specified the channels for the anolog input just in this case. The resource for this device is made with.NET so I am not sure how the resource is named but once you find out that convention you specify a group of lines by separating them by a colon (ex. AnalogInput ai0:1).
Regards,
-Travis E
National Instruments
Applications Engineer

I had trouble connecting my External hard drive

I had trouble connecting my External hard drive (My passport WD) with my macbook. It worked before but not now. The external hard disk is blinking and is spinning but just not showing up on my computer. I tried looking in disk utility and no theres no sign of the disk showing up.
Any help would be greatly appreciated!

Yes, I saw a post on one of these threads about a powered USB hub so I ran over to Office Depot and picked one up. I was finally able to see the HD in the Airport Utility. Yay!

Having trouble connecting column to column using niSwitch on a PXI 2530

Having trouble connecting column to column using niSwitch vi on a PXI 2530 matrix module. I have configured my switch using Switch Executive, have identified aliases, and verified routes and route groups. When I use LabVIEW to connect column to column I get an error reading "cannot find connection between c0 and c1". c0 and c1 are example columns I want to connect. Any help is appreciated.

You can find NISE VIs in the function pallete in LV if you have installed LabVIEW support when you installed NISE (this is selected by default in the installer if you had LV installed before installing NISE).
Also, choose between niSwitch and NISE based on your need - if all you ever do is connect two channels in your application, then configuring a NISE virtual device is probably an overkill (and so is using a switch in this case:-) . However, if you are going to manage multiple routes, then using NISE configuration will let you create named routes and route groups, which you can then invoke (connect/disconnect) in your application and have the configuration part managed outside your application. The code would then concentrate solely on establishing a necessary connection(s) via connecting a route or a route group, while if you were to use niSwitch for this purpose, you would have to keep the logic of connecting inside your application, together with the list of channels that need to be connected.
Start with using NISE, and see if you like it.
http://www.ni.com/pdf/products/us/3msw112-113.pdf
Srdan Zirojevic

Trouble connecting Windows 2000 PC to Airport Extreme

I'm having trouble connecting a PC running Windows 2000 to my Airport Extreme Base Station. The PC is using a D-Link wireless USB 2.0 adapter (802.11g) to connect to the internet. The PC would connect without problem when I was using a D-Link wireless router but will not connect with the new Apple base station.
In addition to the Windows 2000 PC I have a Windows XP PC (connected via ethernet), an iBook G4 and an Epson printer connected to the Airport Extreme and they all work without a problem.
Can anyone tell me how to solve my problem with the Windows 2000 machine?
Thanks.

I am having the same issue; since you did not seem to receive any replies on this forum, am wondering if you resolved the problem; am also wondering if my issue is the distance from my Airport Extreme base to the Windows PC. My next step is going to be to try moving the Apple router closer to the Windows PC and see if that Linksys wireless picks up the signal.

Trouble connecting MCC USB 1208FS to Labview 10.0

Similar Messages

Maybe you are looking for