Trouble getting PM G4 to connect to Airport Express over Ethernet

I was wondering if folks could give me some guidance on how to get my PowerMac G4 (older model with NO airport card) to pull an IP address from an Airport Express. I have the Powermac G4 and Airport Express in one area of my house. The Airport Express is setup as WDS remote on channel 1. I have an Airport Extreme Base Station in another area (setup as WDS main on channel 1) which is connected to my DHCP-enabled Linksys router. Both the Extreme and Express units are set in bridging mode. I was hoping the PM G4 (which is connected to the Airport Express via an Ethernet cable) would pull the IP address off the network (I have the G4 set for DHCP) but so far it is only pulling a bad IP address - not within the range that the Linksys router should be providing.
Any suggestions?

A Mac computer or laptop.....with a sophisticated operating system.....will automatically connect to the wireless access point with the best signal quality based on its location in relation to the device producing the wireless signal.
So, if you move the Mac from one area to another, it will automatically "switch" to pick up the stronger wireless signal from the closest wireless access point.
Other devices....with simplified wireless software.....usually will not do this...and instead will tend to always connect to the first device with which they originally connected.
If you want a device to connect to a specific wireless access point, you might want to try deleting the current wireless connection on the device, moving it very close to the AirPort Express, and then configuring the device to connect to the wireless network again.
With luck, the device will now pick up the stronger signal from the AriPort Express. But, if it does, it will probably stay locked onto the AirPort Express if you then move the device back closer to the AirPort Extreme.

Similar Messages

AirPort Express over Ethernet lost the connection

I have an AirPort Express device. It's works well, if I connect it over WLAN. If I connect the AirPort Express over Ethernet via cable, then after about 15 minutes, I lost the connection between my PC and the AirPort Express.
Does I have to change settings in my router?

then when I try to switch it to extending
That is not the correct setting to use.
"Extending" is only used when an AirPort connects using a wireless connection to another AirPort router.
When the AirPort connects using Ethernet, you have to use the "Create a wireless network" setting.
It might be a lot easier if you simply start all over again and let the configuration "wizard" do most of the work for you. All that you really have to do is name the network, name the Express, enter the password and click Next. Everything else is handled by the configuration utility.
Post back if you are not sure how to do this.

I have an Airport Express connected via optical toslink to a dac/amp in turn connected to speakers. When using iTunes I get message "no speakers connected to Airport Express" and audio sound has drop outs.

I have an Airport Express connected via optical toslink to a dac/amp in turn connected to speakers. When using iTunes I get message "no speakers connected to Airport Express" and audio sound has drop outs.

Ok, if you are connecting the AirPort Express Base Station (AX) to the existing wireless network, then the DSL in the next room is most likely a combination DSL modem and wireless router. Thanks for clarifying that for me.
Although they may only be separated by a single wall, the building material used in that wall may be enough to prevent the AX from receving a "good" signal from the DSL router.
Since I don't know what computing equipment you have available, please check out this AirPort User Tip: AirPort - Optimal Base Station Placement to see if you can get some SNR measurements at the location of your AX. To do this properly, you will want to power-off the AX and only get these measurements for the DSL router.

Question re AEBS Connected to Airport Express via Ethernet

If I have an AEBS that is being used to extend the range of my wireless network, if I connect an Airport Express via Ethernet to this AEBS for purposes of itunes airtunes will this work and will the wireless network remain wireless-n?

Yes, it will.
You also have the option of (a) completely turning off the radio on the Airport Express or (b) leaving it on, and using it to create a b/g point of access to your LAN thus allowing you to run the AEBSn in n-only mode for your n-capable wireless clients.

Connecting Two Airport Express Via Ethernet

I have a unique situation in which I would like to connect two airport express via ethernet. Here is the situation: I can connect the first AX directly to the internet and set up a WDS for the second AX. Unfortunately, the second AX signal does not reach where I need it to go. I can run an ethernet cable between the two. Is this setting valid for a WDS? Or does the WDS have to be wireless? If I can set up the WDS using an ethernet, will the relay AX broadcast the internet wirelessly then?
Are there any specific settings I should know about?
Any help would be great.
Thanks in advance,
Debbie

I currently have an old snow basestation at this location. Can I plug an ethernet cable into it and connect it to the AX?
Yes that will work.
My understanding was that the older basestation could not do this?
I think you have it confused with extending a network wirelessly. That is not possible with the snow AirPort base station (ABS).

Connecting to Airport Express via Ethernet Cable

Dear Apple Support Community,
My setup at home is such that all my devices are in such close proximity to the Airport Express, and therefore I connect everything to the Airport Express via ethernet cables (NAS, Apple TV, PS 3).
The final step in my network setup would be to connect my Macbook to the Airport Express to connect to the internet using the Ethernet Cables, instead of using the wireless connection - because my Macbook is positioned right next to the Airport Express.
However, I am struggling to get the Macbook to connect to the Internet via the Ethernet Cable through the airport express. Is there a special way to set this up if this can be done. I know Wireless would be the answer, but the problem is, when I download movies etc, I write the files directly onto the NAS which happens a lot quicker than doing so via WiFi.
I hope the above question makes sense.
Thanks in advance for any feedback.
Regards
ST

Hello Brian Hunt1. Welcome to the Apple Discussions!
I have an old PowerBook G3 and I do not have a wireless card for it. My plan was to connect it, via Ethernet cable to my airport express which is on my home wireless network (DSL to Mac Mini to AirPort Express via built-in AirPort).
Unfortunately, the network configuration your describing, where you would use OS X's Internet Sharing feature to share the Mac Mini's wired Internet connection wirelessly with the AirPort Express Base Station (AX), won't work.
If I cannot connect my laptop this way, could anyone suggest a wireless card that is compatible with this slightly antiquated, yet very useful machine?
Only the "Pismo" PowerBook G3 is capable of using the original AirPort card. If you have this model, then the following DIY instructions will show you how to install it.
If this isn't your model, then check out the following vendor offerings:
o QuickerTek
o hField Technologies' Wi-Fire

Need help getting LG TV wifi connection with Airport Express?

I can successfully hook the tv up to the network using the dongle PIN method on the Airport Express. It works fine until I turn the tv off. Then I have to go through the whole setup procedure again. Very frustrating. How can I get the Airport to allow the tv access when I turn the tv back on without having to do the setup again? I did not limit access to 24 hours. Not sure what I am missing. Thanks in advance for any and all help.

The dongle is the little usb device that makes the tv wifi capable, it is assigned a unique PIN that I input into the airport express utility so my wireless network will allow it access. All that works fine, but I have to redo the whole setup everytime I turn the tv off. Have you any experience with this and can offer a hint on how to allow the tv access each time I turn it on?

Connecting an Airport Express by Ethernet Cable...

Trying to set up an Airport Express using and Ethernet cable into a wall-socket that's attached to the building's internet hub. (when just connecting by Ethernet cable into the computer from this socket it works fine). Cannot seem to get the thing going? The computer recognises it - however I'm not entirely sure what comes next to get the green light?

How exactly are you trying to use the express? If you want to use it as a router and have several clients connect by wireless.. you will doubtless have double NAT issues.
What IP does the computer get when plugged into the wall socket??
If you have 10.x.x.x address then you must move the IP of the Express otherwise it cannot route a private IP in the same range as the LAN ip.
In the dhcp area move the first two octets to 192.168.
This will then allow the express to work.
You of course also need to have it set to DHCP + NAT.
What version airport utility are you running if you need exact descriptions of how to make those changes.

ITunes 7.1 doesn't recognize Airport Express over ethernet

Running iTunes 7.1 on Windows XP desktop. Immediately after update, iTunes no longer can see my Airport Express as a remote speaker (Airtunes over Ethernet).
Airport Express has the latest updates. Airport Utility has no trouble recognizing it by name. It doesn't have a password on it. The Airport is happily providing wireless for my laptop. It is my only WiFi base station, because I have a small place. It's been dependable for over a year.
I'm truly bummed, because earlier today I got a Griffin AirClick USB, and it works like a charm. I was looking forward to using it with full-screen coverflow in 7.1.
iBook G4 and assorted Win & Linux boxes Mac OS X (10.4.8) iTunes is on an XP PC

The problem turns out to be an incompatibility with Bonjour for Windows. A post by "f00fighter" over in the "iTunes for Windows Upgrade Issues" forum solved it. I quote him below:
******Quote***********
Looks like this issue is due to an incompatibility between Bonjour for Windows and iTunes 7.1.0.59 for Windows (thanks toonz!)
To workaround the issue you can stop the Bonjour Service by going to Start \ Control Panel \ Administrative Tools \ Services, then highlight the Bonjour Service and stop it. You might also want to set the Startup status of the Bonjour Service to Manual (or Disabled) to prevent the service from starting automatically the next time you restart you PC.
Note - this is only a temporary fix, and turns off the Bonjour service...so don't do this if you have other applications that rely on the Bonjour Service. A fix from Apple is needed to truly "fix" this issue.
*****End Quote**********
iBook G4 and assorted boxen Mac OS X (10.4.8) iTunes is on an XP PC

Airport express over ethernet blocks my wifi

Hi.
I have a wifi network via a modem from my ISP and I want to extend it with an Airport Express.
When I connect it over Ethernet, I can configure it to extend the network, but despite having a strong connection (i.e. 4 bars on my MBA, iPhone, etc.), I can't access the internet. There's just no access.
If anyone has any ideas about how I can fix this, I'd be extremely grateful!
Thanks

then when I try to switch it to extending
That is not the correct setting to use.
"Extending" is only used when an AirPort connects using a wireless connection to another AirPort router.
When the AirPort connects using Ethernet, you have to use the "Create a wireless network" setting.
It might be a lot easier if you simply start all over again and let the configuration "wizard" do most of the work for you. All that you really have to do is name the network, name the Express, enter the password and click Next. Everything else is handled by the configuration utility.
Post back if you are not sure how to do this.

Airport 6.3.1 - Unexpected error connecting to Airport Express

I have an Airport Extreme (A1408) base station. I am trying to add an Airport Express (A1392) to my network using Airport Utility 6.3.1 (631.4) with Mac OS/X 10.8.4 (12E 55) running on an iMac. The Airport Utility can find the Express, but returns "An unexpected error occurred. Try again." I have reset the Express using the pinhole without success. I also tried connecting another Airport Extreme (A1408) to the same network with the same result: it can find the device, but returns an unexpected error.
Based on others' posts, I have tried changing the Network setting for IPv6 to "Link-local only". This also did not resolve the problem. Any suggestions are welcome.

I really appreciate your quick response!
The factory default reset didn't work. What did was connecting an ethernet cable. Here's what I did (for anyone else having a similar issue):
Connected the Airport Express via ethernet cable to the Airport Extreme base station.
Airport Utility found the Airport Express and set it up on the ethernet (wired) network. Airport Utility then showed a solid line between the Extreme and the Express to show they were connected.
I then edited the properties of the Airport Express as follows:
On the "Wireless" tab, change "Network Mode" from "Create a wireless network" to "Extend a wireless network".
After the Airport Express rebooted, I detached the ethernet cable.
I then unplugged the Airport Express and plugged it back in the room where I actually wanted it to serve as a wireless extender.
I waited a good 2-3 minutes, checked the status of the connection in Airport Utility in Wi-Fi mode, and voila! It worked. The solid line now shows as a dotted line between the Extreme and Express to show they are connected wirelessly.
I tried connecting a peripheral (in this case, my ethernet-enabled TV) via ethernet cable to the Airport Express extender and it was fully functional.
Thanks again for your help.

Connecting an Airport Express...

I keep forgetting... I just upgraded to the latest Airport Extreme. I have two Airport Express extenders that wouldn't connect.
I'd forgotten that the simple fix is to connect the Airport Express by ethernet, configure it, and then set it loose to its final location.
I'm hoping this will help someone as forgetful as me and, like me, was searching for the fix.

Here are the basic steps to configure an extended wireless network with your 802.11n AirPorts:
Dynamic WDS - Extending a Wireless Network Setup
If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
Open AirPort Utility, and then, select the base station that will connect to the Internet.
Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
Click AirPort in the toolbar, and then, click Wireless.
Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then, select the “Allow this network to be extended” checkbox.
Next, select the base station that will extend this network, and then, choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then, choose the network you want to extend from the Network Name pop-up menu.
Enter the base station network and base station password if necessary.
Click Update to update the base station with new network settings.
(ref: Pages 43-44 of Apple AirPort Networks.)
(ref: Wi-Fi base stations: Extending the range of your wireless network by adding additional Wi-Fi base stations)

Can't get itunes to connect to airport express via air tunes

Hi,
I just bought and installed an airport express (for windows 7) everything is now connected but i can't get itunes to recognize my airport express via air tunes. I can see the multiple speakers in itunes, but when i click on it to connect to airport it just comes up with connecting, loads for about a minute then minimizes without connecting.
Has anyone else experienced this? How can i get this to work?
Message was edited by: Toddy85

You've probaby solved this by now, but if not... When upgrading itunes on a Vista or Windows 7 machine with Windows Firewall running for some reason Bonjour can't get through the firewall and thus Airplay does not work. Not good when all your Hi-fi's are connected via airport express!
I found to resolve the issue you have to install an older version of Bonjour. It won't work if you try to do this straight from Apple. So try this...
1. Firstly install and older version of itunes from the web (say version 10.1) Try www.oldapps.com
2. Then find the Bonjour file in program files
3. Cut and paste it to your desktop with its contents
4. Uninstall itunes and Bonjour via your control panel (the desktop file of Bonjour you moved will still be there).
5. Install your new version of itunes, say version 10.5, from the apple website.
6. Before opening it go to program files and cut the (newly installed) Bonjour file and paste it somewhere different to the desktop (you can't just delete it). It does not matter where you won't be needing it.
7. Now Cut and paste the old version of Bonjour you stuck on the desktop in Program files in place of the one you just moved.
8. Hey presto, Airplay, Windows firewall and your Airport Express' should all get on again.
Hope this works...
Jim

HT4796 im having trouble getting my laptop to connect to my mac using windows migration assistant. my mac comes up with a code but my laptop is waiting for my mac to respond but nothing happens

hi all
im having trouble getting my laptop to connect to my mac using migration assistant. my mac has a code on the screen but my laptop doesnt respond and just says it waitng for my mac to respond.
any idea? please

Hi Christina, belated welcome to Apple Discussions if nobody said it already.
I've had some experiences with these new flash memory recording camcorders, and I'll give you a quick rundown of what I've learned. Many of them (JVC, Panasonic, etc.) tend to record in a .MOD file format, which is non-standard, proprietary, and unrecognizable by most software. I thought Canon was usually a little more standards-compliant, but it appears they also use this .MOD format in your specific camera model. There are likely a couple ways we can get around this though!
In order to play the files, you will likely need to change their file format (.MOD) to .AVI manually. You'll have to locate the files on your Mac, and then manually change the file names so that the file extension (after the period) is .AVI
At that point, a video player application such as http://www.videolan.org/vlc/download-macosx.html>VLC should play the files fine!
You should be able to transfer new video files from the camera to the Macbook Pro with no problems as well. Just plug in the camera to the computer via USB, and also make sure the camera is plugged in to charge. Once it's plugged in, open iMovie (came with the MBP, in the Applications folder) and the MBP should take care of the rest.
Let me know if you have any success with any of this!
FYI, the thread that I got some of the above information from is here:
http://forums.macrumors.com/showthread.php?t=478326
--Travis

I have tryed to connect an AirPort Express to my wireless network. But I alwais get the errocode -4. Can anybody help. I have reset the AirPort Express and updated the software.

I have tryed to connect an AirPort Express to my wireless network. But I alwais get the errocode -4. Can anybody help. I have reset the AirPort Express and updated the software.

The ZyXEL P-2601HN-F1, as you know, is a combination DSL modem & 802.11n wireless router (or gateway device).
For your goal you will want to take a look at this Apple Support article for details on how to configure an AX for iTunes.
If you are still having difficulties with the AX joining the ZyXEL's wireless network, you can try the following:
Temporarily disable wireless encryption.
If you are hidding the SSID, disable that feature.
Change the Mode Select setting to: 802.11g Only
Change the Channel Selection from "Auto" to a set channel, like 1, 6, or 11

Trouble getting PM G4 to connect to Airport Express over Ethernet

Similar Messages

Maybe you are looking for