Trouble installing Driv

Well basically I was having problems with sound in games, whether it be the sound cutting out completely or suddenly get that high pitch screeching sound that can only seem to be resolved with a reboot at which point it'll work fine for anywhere from 5mins to a few hours before one of those happen again. Decided to wipe all the Creative drivers from my system and reinstall. As I went to reinstall I got the error:
"Setup was unable to detect a supported product on your system. Please ensure that your product is properly installed before running this Setup program. Setup will now exit."
Well I figured I'd just try and solve it with a fresh start so I did a complete reformat. Got the same error upon reformatting, so once again I opened up my computer to check to make sure everything was connect properly and nothing was loose. Made sure all the PCI slots were cleaned and reset my CMOS as well just in case.
Upon starting up again I went and made sure I setup the BIOS properly, disabled on-board sound, and what not. When I finally got to the desktop and tried installing I didn't get that message. Well about half way through the driver install I get a blue screen and my computer reboots. Then once I again I'm getting that same error as before. Browsed a few topics where people had this problem and tried doing this (as someone had mentioned it as a possible solution in another topic):
1 - Open an elevated command prompt
2 - Type
bcdedit /set CONFIGACCESSPOLICY DISALLOWMMCONFIG
3 - Reboot
Type this to change back to normal
bcdedit /set CONFIGACCESSPOLICY default
It's just getting really frustrating especially since I had them installing until that BSOD popped up. Just looking for any help possible. Below are my system specs:
Vista Home Premium 32bit
ASUS P5LD2 Deluxe
Intel Pentium D930
2GB PQI DDR2 667
ATI Radeon X900XT
250 GB Hitachi HDD
If there's anything else you need to know, just tell me. The drivers for everything else are all up to date.

Well I bought it a bit over a year ago now, so I'm pretty sure I can't RMA it. Could get some of my friends to try it in their system and if they're having the same problem then at least I know it's probably a hardware issue. It's disappointing that I'm having problems like this after spending a good bit on the card. At least my on-board still works so I guess I'll be using that for now.
If I can get rid of it though, then I'll start looking around for a different product then. This just isn't worth all this hassle.

Similar Messages

I'm having trouble instaling a printer driver for my Canon MG5220. I downloaded the latest printer driver from the Canon website (10.67.1.0) and installed it on my Intel iMac. It said the installation was sucessful, but when I try to add a printer, no go.

I'm having trouble instaling a printer driver for my Canon MG5220. I downloaded the latest printer driver from the Canon website (10.67.1.0) and installed it on my Intel iMac. It said the installation was sucessful, but when I try to add a printer, no go. The printer does'nt show up. I'm fairly new to the Mac, after switching from windows. I'm running Snow Leopard 10.6.8.

Hold down the option key and select
 ▹ System Information...
from the menu bar. In the window that opens, select
Hardware ▹ USB
from the list on the left. On the right you should now see a list of all connected USB devices, as well as some built-in components. Is the device shown?

I am having trouble installing a Roland UM-One driver that is supposed to be compatible with this OS (10.7.1). Any suggestions?

I am having trouble installing a Roland UM-One midi interface driver that is supposed to be compatible with this OS (10.7.2). Any suggestions?

Well, let's hope that nothing was jiggled out of place when you were installing the new hard drive. Your optical drive may just be out of alignment or the disc you have is "dirty." Get a lint-free cloth and some rubbing alcohol, then clean the disc as thoroughly as you can starting from the center and working outward in a concentric circlular motion. See if that helps. In particular clean the inner portion well.
If this does not help, then you have a problem. You have opened the computer yourself. That action voids all support from Apple. If you take the computer in for service the store may refuse to service the computer. This is not related to your now expired warranty.

Installing PCI-6052E having trouble loading driver module - Switch Soft Panel

I'm having trouble installing my PCI-6052E card in a Windows 2000 environment. After installing the card in the computer I boot up the computer, from there I click on the Start button, programs, NI Switch and cannot get the NI-Switch Soft Front Panel to work. When I click on the icon I get an error message returned that says "Failure Loading Driver Module". Any ideas?

Hi PCI Card Problems,
Thank you for posting on the National Instruments forums.
If you are trying to use the NI-Switch Soft Front Panel, please make sure that you have a switch module installed.
If you are trying to bring a test panel for the PCI 6052E, then you will need to open the Measurement and Automation Explorer which is found in Start >> National Instruments >> Measurement & Automation. Right click NI PCI-6052E under Devices and Interfaces >> NI-DAQmx Devices and select Test Panels...
If you only have a PCI-6052E installed, then what you are seeing is expected behavior since the NI-Switch driver is only for National Instruments Switch modules.
Thank You,
Nick F.
Applications Engineer

I am having trouble installing Lion on a partitioned hard drive. Help?

Aloha:
I am having trouble installing Lion on a partitioned hard drive
I have three internal HD's The first I am running the system on 10.6.8 (which is up to date) , the second I do most of my work on and the third I have partitioned into two and I am trying to install Lion on one of the patitions.
But Lion has decided it will only go on the first HD.
Above is the one I want to put it on, but it's not available and I can't change the partition scheme. None of the things the directions state are usable??
What might I be doing wrong?
Thanks
Dan Page

Thanks again for a rapid responce.
I finally got lion on one partition and my daily "SilverKeeper" backup on the other.
Since the only thing I had on the two partition Hard drive was the back up and since the backup would get put on tonight any way I changed the drive to no partitions. This gave me the ability to choose the GUID option, which I did and then I installed two partitions and successfuly istalled Lion on one of them. I even tied Lion into the iCloud successfuly.
But I am not out of the woods yet! I brought My brand new iPad to lunch and was informed that my iPad was synced to my Lion at home and I was on the cloud. That blew my mind, I was impressed.
I then read the Daily news with out problem, however, when I shut down my iPad, that was all she wrote. I can not get the iPad back on. The best I could do was see the revolving gear start and then freeze. It's on charge now and I can not even get rid of the frozen gear.
Not sure this all has anything to do with the recent installation on my main computer, but it's mighty suspicious.
Need some help!!
Thanks
Dan

Trouble installing shared printer on windows 7 64 bit

hey guys
i recently got a IBM thinkpad with Windows 7 Professional 64 bit.
we have a HP Laserjet 3015 thats shared on windows xp profesional computer. i am having trouble installing it on my comuter. if i connect the printer to my computer via USB, windows finds the drivers and it works.
The problem is when ever i try and insatll it over the network it does not work. i can search and find which computer it is attached to and see it in the shared printer list, but when i ever i try to connect to it says connecting>>searching windows update>>cant find drivers. it gives me the option of searching for the drivers to install. i have downloaded the drivers thats on the HP site but they dont help. when ever i select them in the manual it comes with an error saying driver not found then gives u the option of installing it your self. when u select the driver it says windows can not locate a suitable driver.
how can i get around this ??
This question was solved.
View Solution.

rory2g wrote:
i recently got a IBM thinkpad with Windows 7 Professional 64 bit.
we have a HP Laserjet 3015 thats shared on windows xp profesional computer. i am having trouble installing it on my comuter. if i connect the printer to my computer via USB, windows finds the drivers and it works.
The problem is when ever i try and insatll it over the network it does not work. i can search and find which computer it is attached to and see it in the shared printer list, but when i ever i try to connect to it says connecting>>searching windows update>>cant find drivers. it gives me the option of searching for the drivers to install. i have downloaded the drivers thats on the HP site but they dont help. when ever i select them in the manual it comes with an error saying driver not found then gives u the option of installing it your self. when u select the driver it says windows can not locate a suitable driver.
Try the following: On the Windows 7 computer go to the Devices and Printers folder, Add a Printer, Local Printer, Create a new port, Local port, Next, \\xpcomputername\lj3015 (where you put in the actual share name of the computer and printer), OK, Windows Update (and wait for the list to repopulate), HP Laserjet 3015 PCL5, Next, Next.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Black screen while installing driver

Hi all,
I am having troubles installing drivers on my lenovo y560 notebook. When I install the driver, once the screen goes black then come back (normal). After that, it goes black again and it stays that way. Sometimes the mouse pointer is visible and I can move it but it's vey laggy. Sometimes it seems like the screen tries to load and I can see a grey part on the right side of the monitor refreshing in rows. I tried with different version of windows, different driver versions but it's the same. I can only use my notebook with default windows driver which is 1024x768. I have this pc about 3-4 years now and this happened just one day. I used it before for playing but one day it would not boot, after the windows logo it goes black screen again. Sometimes I can see that the process led is blinking and sometimes not. Maybe my GPU chip is ruined? Also, I am not connecting any HDMI external monitors to it.
Solved!
Go to Solution.

Hi Kennyhun,
Welcome to Lenovo Community!
As per the query we understood that you are facing issues with display in your Lenovo Y560 laptop.
Try to boot the system into BIOS and leave the system for a few minutes and check if there is display flickering or any issues related to display is found, also try to boot the system into safe mode with networking option and check for the issue.
Try to update the BIOS and check for the issue.
Click here for the BIOS update for windows 7.
Hope this helps. Do post back if the issue persists!
Best regards,
Ashwin. S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Trouble Installing Windows 8.1 on Yosemite

I am having trouble installing Windows 8.1 using the Bootcamp utility on OS X Yosemite. I downloaded the ISO file for 64 bit 8.1 from Microsoft and put it onto an 8gb USB drive using Bootcamp. My Macbook Pro is an early 2011 (MacBookPro8,2) and is currently running OS X 10.10.1. I know that my MBP doesn't usually support booting from a USB, so I modified the info.plist file using the steps outlined in this thread:
Enable Bootcamp to install from usb for OSX 10.9**WORKS**
This got it to give me the option to boot from the USB when I held the option key on startup.
I have tried the following methods for installing with different errors for each:
1. Installing using Bootcamp created partition
For this, I went through the normal steps in bootcamp and when I got to the disk partitioning stage, I tried to format the drive 0 partition 4 using the format button. After formatting, it wouldn't allow me to continue because of this error: "Windows cannot be installed to this disk the selcted disk har an MR partition table. On EFI systems, windows can only be installed to GPT disks." This lead me to this thread: Windows can't be installed on Drive 0 Partition 4.. It mentions a difference between EFI v. preUEFI installations, but I don't know how to do a preUEFI installation. Enlighten me anyone?
2. Creating a "free space" partition with Disk Utility
For this, I created a free space partition in disk utility and used the Window's installer to format the partition. This allows me to get to the very end of installation, but I get the error message: "Windows could not update the computer's boot configuration. Installation cannot proceed."
BTW, FileVault is turned off.
Any help would be much appreciated!

Hi mgallego,
Which step did the error start to occur ?Have you tried to install it again to have a check ?As the information stated, we can restart the machine to have a check.
Here is a link for reference of the requirements of the Windows 8.1 .
System requirements
http://windows.microsoft.com/en-HK/windows-8/system-requirements
There may be a hardware issue here, it is also recommended to look for help from the manufacturer for help.
Best regards
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

How to install driver for HP photosmart 7520 on MacOSX 10.5.8???

My husband does basic printing of documents. His computer is a MAC OSX 10.5.8. We have a new HP Photosmart 7520 printer which requires 10.6 minimum.
Is it possible to get a driver for this printer for him, that will allow him to access the printer, without getting a new computer!! ?? To simply be able to print and fax and scan.. he rarely does photos.
Please Help, as of course, he is quite frustrated, and as a result, so am I!!
Thanks.

Hi grammaglenys,
Welcome to the HP Forums! I see that you having trouble installing drivers with your printer. It is true that this printer only supports Mac OS X 10.6 as the minimum requirement for the HP Photosmart 7520.
As the Operating System is older than when the printer came out, there currently isn't a driver available. However, here is a list of printers that can be used with Mac OS X 10.5.8. Archived - Mac OS X 10.5.3: Printer drivers included in the HP Printer Driver Update v1.1.1. Or you can try upgrading the Operating System to Mac OS X 10.6.
Hope this answers your question, and have a great day!
RnRMusicMan
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to say “Thanks” for helping!

Having trouble installing Photoshop Elements 13. [was: I wonder if somehow I might have went to Creative cloud because something crossed my screen, but I am not used to doing this so]

I could really use Customer Service help. I received Photoshop Elements as a gift for Christmas...I waiting until i got a new laptop so that I could use that as i was having trouble with older computer. However, I am having trouble installing the software...I swear the dvd added the programs, and I saw them in files explorer i think, but then I cannot find or I was not even able to add the serial number to my knowledge, because it was blank...no keystrokes were shown...and i don't see the program anywhere...Could I have down something wrong and it is somewhere in the cloud?

Thank you. That's what I first thought that I didn't need to do anything
but install from the dvd drive. However after the agreement, it asks me to
sign in at adobe. (Sorry, I'm a little tired of looking at this right
now)...I'll try again tomorrow.
There is no one that I see how to start using the program as I must sign
in. However, I have never been able to get the number to your firm. Or get
the correct number... I think I clicked on a learning tutorial or browsed
Adobe's website to learn more, but got caught up in all the details.
I never uninstalled virus protection to run it because I thought that it
would ask. I'll try again tomorrow I am frustrated. Thank you for your
patience. I appreciate it totally. It's really sad cause I really wanted to
create. I have wanted this for a very long time and I can't believe how
difficult this has been. It would be really nice to know what is really
wrong. I must not be seeing something or I've done something.
On Mon, Apr 6, 2015 at 10:08 PM, Ned Murphy <[email protected]>

Trouble installing older version of Photoshop Elements on Windows 8.1

I'm having trouble installing an old version of Photoshop Elements (I have no need to upgrade) on Windows 8.1 - it keeps saying I need Internet Explorer 4.0 or above, though I have IE 11. I've tried the regedit fix mentioned here: Elements needs version 4 or newer of Internet Explorer to install? but it doesn't seem to be working - the default was already C:\Program Files\Internet Explorer\IEXPLORE.EXE, and the Path was C:\Program Files\Internet Explorer; - I changed it to C:\Program Files\Internet Explorer: but that made no difference. I can't uninstall IE 11 from Windows 8.1, or install an older version.
Can anyone point me in the right direction? Thanks.

I used an IEXPLORE.EXE from internet explorer 7 and set the registry path to that.
Then provided your hard drive doesn't have more than 1 TB of free space, photoshop elements 1 should install and run on windows 8.1
Don't forget to set the registry paths back to what they were originally.

Trouble installing CS4 in Windows 7 64-bit

Has anybody else had trouble installing CS4 into Windows 7 Pro 64-bit? I had this suite installed in XP (32-bit) and it worked just fine, but it will not install on my new computer. The first time I tried, it got partway in (past the serial number), and then everything locked up. I had to restart the machine twice just to make it let go of the CD!
Someone on a forum suggested copying the disks to the hard drive and installing from there, but this did not work any better, the installation simply fails immediately, and I get an error code 1605. I tried it with the firewall off, and with anti-virus disabled, and I never leave User Account Control enabled. What is going on?

Provide the install logs and exact system information:
Troubleshoot installation with install logs
Working with your Operating System’s Tools
Mylenium

Trouble Installing the HP 2540

I am having trouble installing my HP 2540 printer. It used to work for a while, but after some trouble with printing wireless I decided to reinstall the drivers. However, now the drivers want install anymore.
The network printer is found, but the installation doesn't get further than this screen: (it's in dutch, but it says "installing network printer")
After some minutes I get the following screen:
I also tried installing with USB. But it immediatly says that there is some problem and the hardware isn't recognised (I tried all ports).
The laptop I'm using is a MSI with Windows 8
I had no problems installing the printer on another laptop with Windows 7.

Hi
Have you tried to install it using a windows 8 driver?
HP Deskjet 2540 All-in-One Printer series Full Feature Software and Drivers
Hope this helps.
***** Click the KUDOS Thumbs UP (Like) on the left to say 'Thanks'*****
****Make it easier for other people to find solutions, by marking my answer “Accept as Solution”&"Kudos"if it solves your problem.****
-VJ
Although I am an HP Employee, I am speaking for myself and not for HP.

Having trouble installing an HDD.

Just bought a Seagate 7200.8 HDD from Fry's and am having trouble installing it. The drive is SATA.
I've enabled the SATA in bios and also enabled the SATA DMA transfer. I put the drive in and Windows detects it. It shows up in device manager under the disk drives setting. However it does not show up under My Computer so that I can format it. Also the safely remove hardware icon is appering in my system tray for the HDD. I am completely confused.
This is my first SATA drive install so I don't know if i missed a step or did something wrong.
It appears in the bios on IDE channel 4.
One thing I am not sure about is in device manager under the general tab for the drive it's location is listed as "Location 0 (Secondary ATA Channel) which I know cannot be right. That is where my DVD burner is on my second IDE channel.
I am totally lost.
Anybody have any idea what is messing me up.
Thanks in advance.

In the properties of the Taskbar. Right Click in the Taskbar, choose properties then click in Hide inactive icons so it be ticked the click in the Customize button search for the Safely Remove Hardware icon and choose Always Hide from the Dropdown list....that's it.
PS: Np...You're always welcome...
Be well....

Trouble installing itunes -itunessetup.exe is not a valid win32 application

I have trouble installing itunes. The following message appears: C:\Documents and Setting\Owner\My Documents\ itunsSetup.exe is not a valid Win32 application. I tried the following but I still have problems: remove previous version of itunes, remove quicktime, install again quicktime as a standalone, delete temporary files, restart computer, delete all itunes related files.

Finally an answer from Apple:
Dear Stefanie,
I understand that you're receiving an error when trying to open the iTunes
installer that you downloaded. I'd like to try to help you resolve this issue.
It appears that your web browser may be truncating your download of the iTunes
software. I urge you to try using a different web browser to download iTunes. If
this is not possible, you can also try using a different computer to download
iTunes, and then transfer the iTunes installer file (iTunesSetup.exe) to your
original computer and open it from there.
Some transfer options would include using your iPod to transfer the file via
hard disk mode, using a local network, burning a CD, using an external hard disk
or a USB drive, or even sending the file to yourself via email or over an
instant messaging network.
I hope this information helps to resolve your iTunes installation issue. If it
does not and you still need assistance from Apple, you will need to call Apple
technical support (there may be a fee associated with the call). To find the
appropriate phone number, please visit:
http://www.apple.com/support/contact/phone_contacts.html
Sincerely,
Andrew
The iTunes Store
http://www.apple.com/support/itunes/ww/

Trouble installing Driv

Similar Messages

Maybe you are looking for