Trouble Maintaining "Activity" with WRE54G

I have had my WRE54G setup with my WRT54G for about a month or so now. Once I got it setup it worked well for the most part. Now though, the activity light only flashes every so often (not consistently like before) I tried moving the WRE even closer to the router where I know there is a good signal and it works for maybe 30 seconds but then the same problem exists. I tried changing the frag. threshold and RTS threshold as mentioned in other posts and it didn't work. I have also, over the course of a month, changed the channel on both my WRT54G and WRE54G from 11 to 9. On numerous occasions I have power cycled the whole setup and again it works for maybe 30 seconds and then the activity light only starts blinking every 15-20 seconds and I can't even access the WRE's setup page which tells me that I am not even getting a signal from the WRE. Please note though that my link light is a solid blue so I am linked with my router properly...
Is there anything else that I am missing that could be preventing it from working? Also, My wireless router is version 6 and has firmware v1.02.2. My WRE is version 1 and has the latest firmware.
My current settings are as follows:
Channel: 9
Frag. Threshold: 2304
RTS Threshold: 2304
Beacon Interval: 75
Message Edited by mysteriork on 07-06-2008 03:41 PM
Message Edited by mysteriork on 07-06-2008 03:58 PM

Check the connection by using wireless computers with the router alone ... if getting good connection without any issue .... .possibly the Range Extender is gone bad ...
If not then reflash the firmware of the router ... After that reset it for few minutes .... & see if it works or not .....

Similar Messages

Having trouble maintaining remote desktop connection with Mavericks. What is this about needing RDC 3.7.1 with Mavericks. I downloaded RDC 3.7.1 but it does not replace RDC 2.1.0 previously installed.

Having trouble maintaining remote desktop connection with Mavericks. What is this about needing RDC 3.7.1 with Mavericks. I downloaded RDC 3.7.1 but it does not replace RDC 2.1.0 previously installed

Lucky you, it did not work for many users (which as it should be) so MS produced a new version, for ML and Mavericks.
It's in the App Store, for free.
FYI, I assume that you were attempting to post a picture, no one can see it (except maybe you) because it is on your computer rather than the forum server.
file:///Users/dbrant/Desktop/About%20Apple%20Remote%20Desktop%203.7.1.webloc
Use the small camera icon in the editor toolbar to post it.
It also looks like you attempted to use Apple Remote Desktop, which does not do Windows.

Activity with Products

Hi Guys,
I have a scenario where I need to use activity with Products. I looked at the standar transaction 'Business activity with products' but I do not see any tab page to enter products.
Can anyone assist me on how to use/create an activity with products?
Ani

Hi Ani,
First create activity journal template type from easy access using wizard.
Second maintain activity journal template from template type in easy access using wizard.
Third in IMG for activity item provide item category determination.
Finally open your transcation type with category you will find tab "Activity Journal" maintain product data in this tab.
regards
satish kumar

Print activity in Maintain Activity: Which is the SAPSCRIPT o SMARTFORM

Hi to all,
to day a friend of mine have a problem with a print.
In the "Maintain Activity" (CRMD_BUS2000126 transaction) there is the possibility of printing the activity.
There is no immediate output but a spool.
We have to change the output, bue we don't now which is, the sapscript (and if the output is a sapscript)?
Do Anyone know about this?
Regards
Enzo

Enzo,
This is actually quite simple to manage for business transactions. You can control the customizing for actions by using the transaction SPPFCADM. In here you have the customizing for all the actions related to the business transaction. You can alternately get to the parts of this screen via the IMG
CRM->Basic Functions->Actions->Actions in Transaction.
For activitiy it appears that the system is using the standard smartform CRM_ACTIVITY_BUSACT01. I believe you can either redefine the form being used or create a new print action if needed. I personally would recommend that you might want to create a specific action profile for what your users will be needing and assign that to your document type for activities. However I assuming you have copied the standard activity transaction type to a Z-document type for customizing.
Action processing is very flexible and can be used to do almost anything in the background upon request in the business transaction. Another benefit is that action processing works the same in the PCUI or SAP GUI so no need to worry about which one to use.
If you have any more questions reply back, but take a look at the IMG documentation and the wizard and it should be relatively easy to configure.
Good Luck,
Stephen

Network already maintain activity but CJ20N wrong

I already maintain activity in network using CN22, but in CJ20N, the activity doesn't appear below network, how to make it under
network? do I need to assign that network to WBS element first?

It depends on CN22 what you have exactly done. In Cn22 You can create network activity, in that activity if you are not giving any WBS Element activity will show you below network in Cj20n, But if you are giving WBS in Cj20n then activity will show you below in Cj20n.
just bit play with Cj20n overview buttons.
WIth regards
Nitin P.

Trouble maintaining connection since...

I recently updated to 10.4.11 and since then I have had a great deal of trouble maintaining my dial up connection at original modem setting (v92). I have it on v34 currently but it is a slower connection. Using original it dials in, says connecting repeatedly but never does, or does but disconnects soon. Sometimes says no carrier detected, hung up unexpectedly or something else. My laptop on same service is fine. Any ideas?

A warm welcome to the forums!
I wouldn't expect the upgrade to cause, (nor have I heard/read about), any problems with Dial-up.
That being said, the problem probably lies in a partial update or Permissions issue.
1st thing to try...
About Disk Utility's Repair Disk Permissions feature...
http://docs.info.apple.com/article.html?artnum=25751
Reboot afterwards.

Record is not displayed in Historical Reports-Activity with no Customer

Hi All,
We have an issue in Historical Reports for Activity.we are using Book of Business also.
Now the issue is under Activity History as subject area, when an activity doesn't have any Customer it should come as Unspecified in the report.
Like if it doesn't have account assosiated to it then it is shown as Unspecified in the report.
But for activity with no customer assosiated to it, it is not showing the entire record (Acitivity) in the report.
When the Customer field is removed from the displayed columns then we are able to see those activities in the report.
Note:
But when the Book of Business is not there previously, it was working fine
An response is appreciated.
Thanks & Regards,
Lemu
Edited by: Lemu on Dec 28, 2010 10:33 PM
Edited by: Lemu on Dec 28, 2010 10:34 PM

Hi,
Yes we have a workaround for this.
Since the Primary Customer is not exposed as an Activity filed.
Copy the value of the Primary Customer and display it in a filed of activity using workflows.
Then replace the customer filed with this filed.
Then u will get the activity without customer also cause the customer filed is a normal activity field.
Hope this helps.
Regards
Lemu

Diff: Version on workflow builder and Maintain Active Plan version on SWU3

Group,
Can any one help me to understand the Version on workflow builder and Maintain Active Plan version on SWU3
Thanks in advance !
Richard A

Dear Richard Antony,
The Versioning in the Workflow is very important its some what simmilar to the version on any SAP Objets like Tables, Program etc.
Here Suppose any change comes in working workflow, then in stead of directly change them you can create a version of them and them modify it. So that you can reverst back to that version if required.
Like wise there is lots of importance of versioning Workflow.
The Active Plan version is also important to establish at SWU3. As all the Workflow is using Organization management which is very depended on the Active Plan version. so based on which Plan version you want to use you can Provide in SWU3 to tell Workflow system to use this.
Hope this will give you a clear picture.
Regards,
Chandrashekhar.

I have a MacBook Air, OS 10.8.5 I am having trouble sending attachments with Mail. Even small (130K) files don't go. It tries to send then gives up. What can I do to fix this?

I am having trouble send messages with attachments in Mail. Even small attachments (130K) Mail tries to send, then gives up and the message sits in my out box. How can I fix this?

1. You need an external DVD drive.
2. There are no Mac OS X applications or other software in the iTunes App Store.
(116312)

McAfee SiteAdvisor is no longer working with my Safari 8.0. I never had trouble using it with Safari before this latest version. Has anyone else had this problem?

McAfee SiteAdvisor is no longer working with my Safari 8.0. I never had trouble using it with Safari before this latest version. Has anyone else had this problem? I contacted McAfee support and they said nobody else is reporting this issue.

Wow, life is certainly tough for you.
S***t happens. That's why there's a warranty.

Creation of Activity with campaign

hi guys,
Can anybody help for the below scenario.
I am creating an activity with an 'CAMPAGIN ID'. Once the Campagin id is populated in the activity transaction and click on save button it will become as a preceding document for the activity.
I am using the function module(BAPI_ACTIVITYCRM_CREATEMULTI) to create an preceding document as marketing campaign for the activity. But it was not working.
can anyone guide how to approach to the above mention scenario. If possible post sample code.
Thanks
Viswa

Hi Viswa
Try this.
Create a Marketing Campaign first.
On save create activity using actions.
Thanks

If imessage is not activated with my phone number, does text messages can be forwarded to my ipad?

my imessage is not activating with my mobile number, i do not receive code for text forwarding in my ipad/ air 2, my iphone 4s and ipad is operating with the same iOS. plz help i am being able to use call and messages forwarding facilities.

Hi, uttam_june15.
Thank you for visiting Apple Support Communities.
I am not sure if you are unable to activate iMessage or that your phone number is not registering with iMessage. However, here are the troubleshooting articles that cover both scenarios.
If you get an error when trying to activate iMessage or FaceTime
iOS and OS X: Link your phone number and Apple ID for use with FaceTime and iMessage
-Jason H.

Nexus 1010 HA Active with warm standby

I have deployed two 1010 appliances, the upstream switches are two 6509 wihtout VSS.
I cannot get the HA up.
Output of show module is:
Mod Ports Module-Type                       Model               Status
1    0      Nexus 1010 (Virtual Services App Nexus1010           active *
2    0      Virtual Supervisor Module                             powered-up
Mod Sw                Hw
1    4.2(1)SP1(3)      0.0
Mod MAC-Address(es)                         Serial-Num
1    00-19-07-6c-5a-a8 to 00-19-07-6c-62-a8 NA
Mod Server-IP        Server-UUID                           Server-Name
1    10.146.102.10    NA                                    NA
Output of show system redundancy status is :
Redundancy role
      administrative:   primary
         operational:   primary
Redundancy mode
      administrative:   HA
         operational:   None
This supervisor (sup-1)
    Redundancy state:   Active
    Supervisor state:   Active
      Internal state:   Active with warm standby
Other supervisor (sup-2)
    Redundancy state:   Standby
Error in getting supervisor and internal state of other supervisor.
and the output of show system internal redundancy info is:
My CP:
slot: 0
domain: 25
role:   primary
status: RDN_ST_AC
state: RDN_DRV_ST_AC_SB
intr:   enabled
power_off_reqs: 0
reset_reqs:     9
Other CP:
slot: 1
status: RDN_ST_SB
active: true
ver_rcvd: true
degraded_mode: true
Redun Device 0:
name: ha0
pdev: f37e8640
alarm: true
mac: ff:ff:ff:ff:ff:ff
tx_set_ver_req_pkts:   319
tx_set_ver_rsp_pkts:   0
tx_heartbeat_req_pkts: 61193
tx_heartbeat_rsp_pkts: 0
rx_set_ver_req_pkts:   0
rx_set_ver_rsp_pkts:   0
rx_heartbeat_req_pkts: 0
rx_heartbeat_rsp_pkts: 0
rx_drops_wrong_domain: 0
rx_drops_wrong_slot:   0
rx_drops_short_pkt:    0
rx_drops_queue_full:   0
rx_drops_inactive_cp: 0
rx_drops_bad_src:      0
rx_drops_not_ready:    0
rx_drops_wrong_ver:    0
rx_unknown_pkts:       0
Redun Device 1:
name: ha1
pdev: f37e8240
alarm: false
mac: 00:02:3d:70:19:81
tx_set_ver_req_pkts:   314
tx_set_ver_rsp_pkts:   0
tx_heartbeat_req_pkts: 61193
tx_heartbeat_rsp_pkts: 0
rx_set_ver_req_pkts:   0
rx_set_ver_rsp_pkts:   5
rx_heartbeat_req_pkts: 0
rx_heartbeat_rsp_pkts: 61165
rx_drops_wrong_domain: 0
rx_drops_wrong_slot:   0
rx_drops_short_pkt:    0
rx_drops_queue_full:   0
rx_drops_inactive_cp: 0
rx_drops_bad_src:      0
rx_drops_not_ready:    0
rx_drops_wrong_ver:    0
rx_unknown_pkts:       0
Can anyone please help in resolving this issue.
Regards,
Sabih

Hi Sabih,
For a Nexus 1010 pair to form HA redundancy, the communicate with each other via the Control VLAN. You would have specified this during your installation.
Can you verify that they are both utilizing the same Control VLAN.
n1010# show svs domain
Furthermore, ensure that this vlan is defined and forwarding, on the relevant ports, on the upstream 6509s.
Thanks,
Michael

Design panel not active with php file?

I have DW CS5 on two computers. One one the design panel is active with a PHP file. On the other, it is not active.
I must have a setting wrong on the one computer. What do I need to do to make the design panel active? The code panel is fine on both.
It is very hard to work on a PHP file when I can't see the design panel.
Regards,
Bill Schaepe

The problem is that I have a number of PHP files that I need to modify the words in a form and it is hard to see what I am doing.
You can't do this in Code view?
On both computers, I just generate a new PHP file. On the one computer the design panel is active and I can click design tab on it to see the design. On the other one, I can't click on the design panel tab to see the design.
Both the same version revision level of DW? Both on the same platform? Do you have an option to click on "Design" under View on the main menu?

I am have trouble sending email with an attachment?

I am having trouble sending emails with an attachment. Does anyone have a solution to this problem?

Impossible to answer with information provided
Allan

Trouble Maintaining "Activity" with WRE54G

Similar Messages

Maybe you are looking for