Trouble replacing Hard Drive

Hi all,
I'm struggling to replace my hard drive on my 2.0 GHz MacBook. Want to upgrade from 60Gb to 160Gb. Ordered the below hard drive from OWC:
http://eshop.macsales.com/item/Hitachi/0A28844/
The swap out of drives was easy (after having to run to WalMart for a #8 T wrench), but when I restart the MacBook with the installation CD, there is no "destination volume" for me to install Mac OSX.
When I compared my two drives, they look very similar (SATA 2.5"), however the new drive does not have four brass looking 'prongs' on the left right top corner. Other than missing these, the new and old drives appear the same.
Any thoughts would be appreciated.
James
2.0 MacBook   Mac OS X (10.4.8)  

Do you mind going into detail about that disk utility? How did you go about fixing this, because I am having the exact same problem.
I purchased a 200GB Toshiba (MK2035GSS). Installation of the drive was pretty simple, but when I began installing the CD, the "destination volume" did not show as well.
Any advice would be greatly appreciated.
White Macbook 2GHz Intel Core 2 Duo   Mac OS X (10.4.8)  

Similar Messages

  • Trouble replacing hard drive--MacBook won't recognize new drive

    The HDD in my wife's black MacBook (2007, I think) won't boot up. I've run Disk Utility and have decided it's pretty much dead. I have a Carbon Copy backup, so the data is fine.
    I've tried replacing the drive twice now, and the MacBook simply won't "see" the new drives. When I install the drive, nothing shows up in Disk Utility (run either from the install disc or the Carbon Copy backup drive in a USB enclosure).
    The new drives are formatted (I even copied the bootable backup to one of them), and the computer sees them just fine if I install them in a USB enclosure and hook them up that way. When I put them in the computer, though, no dice. Her old, corrupted HDD still showed up in Disk Utility when I reinstalled it, but the new drives don't...
    What am I doing wrong?!? What else can I try?

    Well, I'm not too surprised with the WD drive, but am with the Seagate. I've installed numerous Seagates without ever having a problem. Most recently two XT500 hybrids in two MBPs. The WD drives on the other hand have proven problematic especially the Blue models.
    In any event the problem could be jumpers or firmware configuration. The WD drive may be pre-configured to work on SATA-II 3.0 Gb/s busses, but the laptop only has a 1.5 Gb/s bus. So the drive's configuration may have to be changed. I don't believe that should be a problem with the Seagate drive, so I'm not sure what the problem with it would be.
    I would contact each manufacturer's tech support to see if they can help sort things out for you. The fact that both drives work in an external enclosure does help a little since the interface cards mask certain pins on the drive that don't pass through to the internal hardware. Whatever that may be could be why the drives aren't being detected.

  • I am having trouble finding a replacement hard drive

    Evidently I blew my hard drive when I installed a web cam.  Now I can't seem to find a replacement hard drive for my z61t through Lenovo online or phone service.  Does anyone have any tips on where I can find a replacement?  I'm so discouraged -- I should have bought a warranty but thought they should guarantee it longer than 1 year so on principle I held out.  Now I am 2 months past warranty and this is where my principles got me!!!  I am a fifty-something technophobe -- can any of you youngsters help me?!?!
    Thank you!

    Welcome to the forum!
    At today's low prices for SATA drives, this would be my pick:
     http://www.zipzoomfly.com/jsp/ProductDetail.jsp?ProductCode=10008857
    I have it in my T60p and love it...
    Hope this helps.
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • IPod 4th Gen Click Wheel replaced hard drive; problems

    Ok, So I replaced the 20gb hard drive with a new EXACT replacement hard drive, no other problems with iPod. But iTunes will not recognize it because the hard drive is not formatted. I tried formating it with Disk Utility but keep getting error messages. Im not sure what format to use. When the 4th gen came out Intel processors werent here so Im sure I need to simply format as Mac OS Extended. There is no HFS= format in Disk Utility. Im lost as to what to do. Please help??!

    hmm - curiouser and curiouser
    I've now managed to get it to manually update (after iTunes took 100% of system resources and I had to force quit it...) but that still doesn't really help me with the auto-sync feature which still won't work
    aaaaaaggggggghhhhh

  • MacBook Pro does not boot past apple screen after replacing hard drive

    After replacing hard drive on MacBook Pro 13 inch early 2011 model, the screen only boots to the apple logo.  Do I need to re-install the OS?

    The problem is that the OS is not in any where else of the MacBook Pro than in the HD / SSD. If you replace the Hard Drive, then you will need to Re-install OSX into that hard drive, it's pretty easy.
    1) Power up your Macbook Pro, as fast as you can press and hold the Option key (ALT). You'll see that it opens the bootable-devices you have, you'll see a Recovery partition, click it.
    (If the Hard Drive contains data do the following)
    2) In the menu select Disk Utility.
    3) In Disk Utility go ahead and select the Hard Drive that is inside the MBP.
    4) Erase the content.
    (If the Hard Drive contains no data continue with the following jumping the last 3 steps).
    5) Select Re-install OSX.
    6) Select the Hard Drive in which you want to install it.
    Follow the steps of everything else (it should take approximately 1 hour to do the whole thing).
    Hope this helps!
    Later.

  • I went to Mac Store and had replaced hard drive because I encountered 4HDD ERROR(hard drive failure). I had backed up my old hard drive by TIME MACHINE regularly. Now how can I restore everything I had?

    I went to Mac Store and had replaced hard drive because I encountered 4HDD ERROR(hard drive failure). I had backed up my old hard drive by TIME MACHINE regularly. Now how can I restore everything I had?

    Thanks for your response.
    I had tried COMMAND+ALT+R which led me to directly to INTERNET RECOVERY via wifi. After 1 hour or so it dropped me at the same point.
    I've tried MIGRANT ASSISTANCE as well, it kept on LOOKING FOR OTHER COMPUTERS even though I clicked on TIME MACHINE BACK UP USING EXTERNAL HARD DRIVE
    so what to do now?
    P.S. Guys at MacStore were so careless to even listen to me when I asked them about retrieving back up :(
    Please help

  • I have an iMac 21.5 inch purchased in 2011 with a failing 1TB Seagate hard drive. Can I get a replacement hard drive?

    I have an iMac 21.5 inch purchased in 2011 with a failing 1TB Seagate hard drive. Can I get a replacement hard drive thru the Apple Replacement Program? I did purchase the Applecare Plan but it expired in Dec. 2013.

    FWIW, if you purchased the iMac in 2011 and purchased Applecare, you are covered for a total of 3 years. You mentioned yours expired in December 2013 - that cannot be unless you bought yours in 2010. If you bought it in December 2011, you should still be covered until December 2014 - if so, contact Apple/make a Genius Bar appointment quickly so the replacement is covered by the warranty. The hard drive replacement program might have expired, but as long as you're covered by Applecare, a drive replacement is covered.

  • Can anyone help me with advice for a replacement hard drive

    Hi there,
    Can anyone help me with advice for a replacement hard drive and RAM upgrade for my Mac Book Pro 5,3
    Its 3 years old & running Snow Leopard 10.6.8
    I do a lot of audio & movie work so performance is important.
    The logic board was replaced last summer & I was advised to replace the hard drive then...oops
    Anyway it has limped on until now but is giving me cause for concern...
    I have found a couple of possibilities below...so if anyone does have a moment to take a look & help me out I would be most grateful
    http://www.amazon.co.uk/Western-Digital-Scorpio-7200rpm-Internal/dp/B004I9J5OG/r ef=sr_1_1?ie=UTF8&qid=1356787585&sr=8-1
    http://www.amazon.co.uk/Kingston-Technology-Apple-8GB-Kit/dp/B001PS9UKW/ref=pd_s im_computers_5
    Kind regards
    Nick

    Thanks guys that is so helpful :-)
    I will follow your advice Ogelthorpe & see how I get on with the job!!! Virgin territory for me so I may well shout for help once my MBP is in bits!! Is there a guide for duffers for this job anywhere??
    & yes in an ideal world I would be replacing my old MBP but I'm just not in a position to do that at the moment....let's hope things pick up in 2013
    All the very best
    Nick

  • My 2010 imac does not recognise my time machine since I had the Seagate replacement hard drive. Any thought from anyone? The External hard drive is a 1 TB seagate

    My iMac (2010 intel model) does not recognise or communicate with my external seagate drive as a time machine for back ups since I had the 1TB Seagate replacement hard drive as part of the replacement prgram with OSX LION 10.5.8 installed.
    Is this because I need to update the time machine drive itself?

    This excellent Support article may help you solve that TM problem:
           http://pondini.org/TM/Troubleshooting.html

  • Replacement hard drive not shown in Disk Utility

    So I just finished installing a replacement hard drive for my PB 12". I got a Seagate 2.5" ATA Momentus 5400 etc as per my previous thread. But after firing it up from the install disk, the new volume fails to show up. Anyone else had this problem? And fixed it? Opening up the case again now...

    Don't know if your problem solved. Had the same thing happen to me. Was told that new HD was bad (unlikely), Logic board was bad (disaster). Then finally was tole by another tech (OWC) that it sounded like a bad cable connection. Took it apart again and reseated both ends of HD cable a couple of times. Started up and the HD recognized by disk utility. Works great since. Hope your problem as simple as mine.

  • How to replace hard drive in macbook pro?

    How to replace hard drive in macbook pro?

    Hi S,
    If you have the newer unibody style, it's very easy. If it's one of the earlier models, it's considerably more difficult. Go to Apple Menu > About This Mac > More Info > Hardware and find your Model Identifier. Then go to ifixit.com, or powerbookmedic.com or macsales.com or youtube or others and there are illustrated, detailed directions. Good luck to you and post back if you have further questions.

  • Dv6700 broken HDD "#10009 replace hard drive"

    Hi, My laptop model dv6700 and harddrive: SATA 250Gb. I have made recovery discs. Issue: hard drive gave up recently and in BIOS HDD checkup it showed "#10009 replace hard drive" Query: 1)since I need to replace the hard drive, i wish to upgrade it to 500GB.Is it possible or not?? 2)if yes, are there any constraints on size,make of HDD?? 3)Once i replace my HDD how to get my old OS(i got vista home premium along with laptop)?? 4)will there be a problem if i use my recovery discs on the new 500 Gb HDD?? 5)will there be any conflict in recognizing the new HDD of 500 Gb?? Is there any other way to solve this issue without replacement?? Thanks in advance!!
    This question was solved.
    View Solution.

    Here are answers to your question.
    1) You can upgrade to 500GB and its possbile without any problems
    2) No constraints on size or make. You can use any brand or manufacturer of your own choice
    3) You need to install your OS using recovery disks. There is a guide available over here
    4) There will not be any problems if you using recovery disks on new HDD
    5) There wont be any conflict. If you do face any issues, you can always post your query on the forums.
    6) Unfortunately there is no other way. If the HDD test fails, it means its gone. Only option is to replace HDD.
    //Click on Kudos and Accept as Solution if my reply was helpful and answered your question//
    I am an HP employee!!

  • After i replaced hard drive my bluetooth disappeared where can I find it?

    After i replaced hard drive my bluetooth disappeared where can I find it?

                If you are talking about the bluetooth software (to connect devices) then you can download it here!

  • Suggestions on replacement hard drive

    I'm needing a replacement hard drive for a 733MHz 128MB 40G Quicksilver. Anyone with experience on certain brands?
    Thanks,
    Jason

    Jason:
    A 120GB (ATA-100 or ATA-133) drive is perhaps the optimum size... You've confirmed that Mac won't see more than the first 128GB of any drive connected to the native drive bus on the logic board. You may add a drive larger than 120GB to this bus (in case you find a larger drive for less money than a 120GB one), but only the first 128GB will be recognized after formatting. For larger drive internal use at full capacity, you'd need to add a PCI controller card to hook the drive to.
    To physically install the drive, you need to correctly set the jumper pins on the drive and then connect it to the proper connector on the ribbon cable. (I assume that the current drive is working and you'll be duplicating the data on it to the new drive. If I'm wrong, please let me know.) One of the drives will be pinned as master (single master/single drive) and connected to the end of the ribbon cable; the other pinned as slave and connected to the inline connector. They get mounted one above the other in the drive stacking tray that's in the Mac. The new drive will come with the jumpers, mounting screws and a spare ribbon cable, so you'll have all that you need).
    If you need help with this, let us know after you've purchased the drive (pin setting positions vary on different brands). Don't drive yourself crazy with the installation manual that comes with the drive, which is confusing and Windows-oriented. Also note that the accompanying software CD is useless for Macs. You'll instead simply use Disk Utility to initially format (initialize) the drive.
    As for cloning, I think that the most user-friendly software is SuperDuper, which I'm pretty sure you'll find to be a snap to use. (I'm a long time fan of CarbonCopyCloner, but recently tried SuperDuper to familiarize myself with it and was very impressed by how friendly it is.) It walks you through the volume duplication process in a few easy steps.
    Gary
    1GH DP G4 Quicksilver 2002, 400MH B&W rev.2 G3, Mac SE30   Mac OS X (10.4.2)   5G iPod, Epson 2200 & R300 & LW Select 360 Printers, Epson 3200 Scanner

  • Download mountain lion on replaced hard drive

    I need to download mountain lion on a replaced hard drive. how can I do this?

    If your Mac came with 10.7 or 10.8 installed, you'll have access to Internet recovery - reboot holding down cmd-R and follow the prompts.
    If you started on 10.6, you must reinstall that OS first and then use the App Store to install 10.8.
    Matt

Maybe you are looking for