Trouble setting up X with FreeBSD 7.1 on my Thinkpad T60 1951-FCG

Hi!
I'm having some trouble setting up X on my Thinkpad T60 1951-FCG running FreeBSD 7.1. When I run whatever config, either the one I get from X -configure or one edited after my settings, all I get is a black screen. The screen is a tad bit lighter than when my laptop is powered off though. This effectivly locks my laptop up -- the only way I can get out of the "black screen of death" is to SSH in and kill the process, which then turns my monitor into this: http://folk.ntnu.no/sigurdhj/laptop_fail.jpg. The only way I can get back to a normal screen is by rebooting. If I try to start X through SSH, I get prompted with the message: Failed to load DMI info, X60 TV quirk not applied.
I've given the 'vesa' driver a go aswell, with that I can get a picture at least, but still loads of error messages. My monitor works perfectly with Windows XP, Ubuntu, and PC-BSD -- which leads me to believe that my monitor is fine, and that it's just a matter of configuring it right.
After the read of 'man intel' I'm thinking it could be something with the setting LVDSFixedMode, but the information about that was just too advanced for me to make anything of. I've included my xorg.conf.new file aswell as the Xorg.0.log file.
Hope there is someone out there bored enough to help me sort this out.
(xorg.conf: http://folk.ntnu.no/sigurdhj/xorg.conf.new.txt )
(Xorg.0.log: http://folk.ntnu.no/sigurdhj/Xorg_0_log.txt )
Cheers,
Kladd

If you check the info on the AirPort Utility 5.6.1 download page, this application is for Leopard and Snow Leopard....10.5.7 to 10.6.8
It will not run on Lion
Instead, you need to download and install AirPort Utility 5.6 for Mac OS X Lion

Similar Messages

Is anyone else having trouble setting up messages with the new mountain lion software? I keep getting a notification that i cant sign in and it is saying, check network connection and try again, but i have full wifi bars, thanks, Justin

is anyone else having trouble setting up messages with the new mountain lion software? I keep getting a notification that i cant sign in and it is saying, check network connection and try again, but i have full wifi bars, thanks, Justin

Install this to get X11 functionality back in 10.8
http://xquartz.macosforge.org/landing/
Worked great for me and others.
Jerry

Having trouble setting up Mail with a POP account

I am trying to set up Mail with my Universities webmail service, and according to their tech page I need to set it to POP. I also made sure that I have the incoming and outgoing mail servers correct, and i've made certain that I am entering my username and password correctly. But when it loads and trys to get my mail it says that the password I supplied is incorrect, but I know that's not true. I am absolutley sure that both the username and password are entered correctly.
Does anybody know how I might fix this?
p.s. my girlfriend is having the exact same problem, so it isn't just me entering something wrong

I know you said the usernames/passwords are correct but, (if you can), login via webmail using those same strings, see if that works.
Write the text to a note and copy and paste from there so you are sure you've not input something wrongly.
Failing that do a quick keychain first aid too.
If that don't work then I'm out of ideas, (for now at least).

Having trouble setting up headset with microphone

Hi,
I own a satellite A135 that is currently running on Windows Vista Home Edition. I tried using a headset with mic but somehow the mic always turns to mute after I've exited the set-up page. I'm starting to get frustrated, particularly since I need to talk with someone using Skype. Please help.
Thanks

I have this issue, too. Did you find a solution since you first posted?

Having trouble setting up router with verizon modem

im trying to set up my linksys router wrt54gs with my verizon dsl modemr. im having a hard time.

Try these steps :
Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter. When
it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If you are getting Ip - 192.168.1.X ...change the LAN Ip to 192.168.2.1 ....Power cycle for 3-4 minutes ...
Try going online
If still not working ...use Internet Connection type as PPPOE .... Use Username & Password provided by Service Provider ....
Click save settings....
Look for WAN IP address again under status page ....
Hope it works for you....

Having trouble setting up sonos with my airport extreme

After setting up the airport extreme I can no longer access my wireless sonos speakers. The bridge is connected to the airport and that's fine but it won't recognize the wireless speakers. I think it is probably a config issue. On my old router I could set up a channel for sonos to use but can't seem to find how to do this on the airport or if it is possible? Anyone have any ideas? or are familiar with Sonos? Thanks

I have this issue, too. Did you find a solution since you first posted?

Trouble setting up NAT with ipfilter

Hello All :
I'm trying to setup a Sunfire V120 as a NAT box but am running into some odd behavior that I can't seem to resolve, I'm hoping someone here can shed some light on the problem.
My V120 has two NICs eri0 and eri1 and is running Solaris 10, Release 08/07. I have configured eri0 as my public interface and eri1 as my private interface.
I turned on packet forwarding :
routeadm -u -e ipv4-forwardingI also added the following to /etc/ipf/ipnat.conf:
map eri0 192.168.0.0/24 -> 0/32 proxy port ftp ftp/tcp
map eri0 192.168.0.0/24 -> 0/32 portmap tcp/udp auto
map eri0 192.168.0.0/24 -> 0/32ipfilter is running:
online 10:26:33 svc:/network/ipfilter:default From another system inside my private network, I can ping machines on the private network and on the public network. However, I cannot ssh to other external addresses, ftp, and DNS does not resolve, but I am able to ping the addresses of the public DNS servers just as I am able to ping any other public and private address.
Thanks in advance for any help one can provide.

I also added the following to /etc/ipf/ipnat.conf:
map eri0 192.168.0.0/24 -> 0/32 proxy port ftp ftp/tcp
map eri0 192.168.0.0/24 -> 0/32 portmap tcp/udp auto
map eri0 192.168.0.0/24 -> 0/32Maybe it should be 192.168.0.0/16 or just "map eri0 0/0 .. "? Otherwise OK
Thanks in advance for any help one can provide.Check:
# /usr/sbin/ipfstat
# /usr/sbin/ipfstat -nih
# /usr/sbin/ipfstat -noh
Should list status and your inbound and outbound rule sets respectively.
# /usr/sbin/ipnat -l
Should list your NAT rules and active dynamic entries
# less +F /var/adm/messages
(or where you send local0 syslog (if you log))
# /usr/sbin/snoop -rd eri0
# /usr/sbin/snoop -rd eri1
Should show briefely what's on the wire-side of ipf. Run both in two windows and compare and look for leaks of internal addresses on the outside and missed packets.
P�l

Having trouble setting up e-mail on new iPhone 4s. I would like to sync with my outlook mail, contacts

I am having trouble setting up my email and syncing my outlook calendar wiht my new iphone 4s.

How do you connect to the internet?
Most of the time, the problem lies here. You can try a couple of things. First, try only 3G or carrier data. Then, try only wifi. If that still doesn't work, your only other option is to try a different hotspot.
I had the same problem before when I updated to iOS 4.3. I thought it was the update at first. I usually have the carrier data turned off because my plan doesn't have an unlimited provision for it. I forgot that I also switched ISPs from DSL to a visibility unit package - meaning I had to setup my laptop so that I could get wifi from it. I realized this when I visited a friends house that I knew I could connect properly before.
My problem was with my laptop. It seems that Little Snitch blocks the ports being used for mail and push notifications. I haven't figured it out exactly since I still can't get email when I'm using my laptop connection. But, it works fine when I'm using ONLY 3G or both/wifi only if connected to a different hotspot.
Hope that helps.

Having trouble setting up a linksys WRT54GS router with v...

Having trouble setting up a linksys WRT54GS router with verizon DSL using a westell 6100F modem. the modem works fine by its self but the router will not connect to the internet when installed like the cd tells you to.
online help and phone help has been less than helpful, anyone have any Ideas?

Ok I found " Installing the liksys wireless router with a westell 6100 modem" in the verizon troubleshooting guides. printed the instructions so I would'nt forget. step 1 open your web browser and enter http://192.168.1.1 in the address field. PROBLEM it comes up with a login screen that I don't know how to sign into. tried the obvious stuff. cannot get past the login screen. I knew this sounded to easy to be true. anyone have any ideas?

Having trouble setting up my website. It's probably a silly mistake.

So I've registered a domain and hosting plan with A Simple Orange which had a pretty good deal since I had a coupon for 20% off. I've tried using Joomla to manage my website, but I couldn't get the hang of it. So I'm trying out iWeb 09' now and just having trouble setting it up. I've gone to me.com and added my website and added the CNAME correctly I hope. Here is a picture. http://imgur.com/XI8Lw.png
Next I opened iWeb and setup MobileMe in the preferences panel. I've tried publishing the information from iWeb to my website, but my home page doesn't change. You can see here at RyanSchefer.com that it's just plan

No. Your CNAME setting is not correct. The CNAME and web.me.com are correct with web.me.com being your host. However, your domain name is incorrect - don't understand why you have put mobileme before it? You just enter either your domain name on its own so domain.com or you need to set up two separate CNAME entries, one being for www, CNAME, web.me.com and then one being @, CNAME, web.me.com. The @ stands for your domain name and the www is your sub domain.
Try altering this and it should work okay.

Having trouble setting up email accounts in the mail app?

Hi Apple community,
I am having trouble setting up my email accounts with the osX mail application. I have two accounts, an outlook and my college email through google. When I try to add the outlook account the prompt says that it cannot connect to the server and when I try my college mail i get the following prompt.
"Trying to log in to the Exchange server “autodiscover-s.outlook.com” failed. Make sure the email address and password you entered are correct, then click Continue."
Please note that my college account is run by gmail and ends in murraystate.edu
Thanks, Will.

Hey will,
okay for your college email. Heres what you do.
Try adding your email and wait for the message to come up
Trying to log in to the Exchange server “autodiscover-s.outlook.com” failed. Make sure the email address and password you entered are correct, then click Continue."
Once it does, you will notice 2 extra boxes One says username and the other password. You will notice that the username will not have @murraystate.edu
Add this and continue and this should now be added as an email account and should be able to receive emails as normal.
For your outlook emails, I would recommend using the following article to set it up. It is fairly straightforward.
http://howto.cnet.com/8301-11310_39-57602775-285/how-to-set-up-mac-mail-to-use-i map-for-outlook.com/
Hope that helps.

Having trouble setting up FaceTime. keep giving me Apple ID password

having trouble setting up FaceTime. trouble at verifying use I'd. I have my email setup with different password since I have tw setup email. my Apple ID has different password. same email name.

Hello sangjaimepark,
Thank you for the details of the issue you are experiencing with activating FaceTime. I recommend reviewing the article below for FaceTime activation issues. When trying to activate FaceTime, you will need to use the email address you use for your Apple ID and your Apple ID password and not your email password:
iOS: Troubleshooting FaceTime and iMessage activation
http://support.apple.com/kb/ts4268
Thank you for using Apple Support Communities.
Best,
Sheila M.

Having trouble setting up network

Hi guys,
I just recently moved to a new house and am having trouble setting up the network with my airport extreme. There is a cable modem that is networked to the house so that every room has an outlet.
I connected the airport to one of the outlets with my macbook and when I create network, I cannot connect to the internet wirelessly even though the macbook detects a network when I set it up with bridge mode. But hard wired through the router I can surf the web as I am doing right now.
When I hit share an IP address, the internet does not work at all. It seems to work fine with my old netgear router, but would prefer using the airport.
I've also reset the airport as well with still no luck. Any help would be appreciated. Thanks

Have you tried powering down the modem for 5 min and then turning on with the ethernet connected to the WAN port of airport extreme?

MSI X58 Pro - I'm having trouble setting up my first Raid 0 Array

Hey guys! I have an i7 920, X58 Pro, 3x2GB DDR3, Radeon 5850, 640GB WD Black (Windows 7 64 bit + applications) and 1TB Samsung F3 (backup) system and I'm having trouble setting up a raid 0 array. I recently decided to purchase two additional 1TB Samsung F3 harddrives in order to create a raid 0 array, while still keeping my original two harddrives separate. I installed the new harddrives today, installed the JMicron drivers that were on the drivers disk that came with my motherboard, went into the bios, and changed it from IDE to RAID. I then went into the raid bios, selected the two new harddrives and selected raid 0, saved everything and tried to load Windows and Windows refuses to boot up. I got an option to try fixing Windows but that didn't end up fixing anything. Finally, I was forced to go back into the bios and switch it from RAID back to IDE just to get Windows to boot up again. Does anyone know what I need to do in order to get this raid 0 to work? Thanks a lot in advance for your help!

Perhaps create a software RAID? You can do it in Windows through Control Panel --> Administrative Tools --> Computer Management --> Disk Management.
A quick guide: http://www.softwaresecretweapons.com/jspwiki/windows-7-software-raid-disk-partition-and-volume-context-menus

Problem setting up Wireless with WAP54G

I am having trouble setting up my wireless network with my WAP54G access point. I have used this same router successfully before but now on my new network it gives me trouble.
I did a reset on my Access Point, Then the default setting is with a static IP address. I can just connect with the access point (wireless) with no problem. But when connected to the modem it doesn't give me internet...
Reading the manual of the modem it tells me that any router connected to the modem should be set to DHCP. So when I put the settings on my access point to DHCP (and change them on the network settings of my laptop) I cannot connect with the Accesspoint anymore..
Can anyone help me? am I just doing something stupid here?

Hi sdedmer. What is the make and model of your modem? Is it a modem-router-in-one or a gateway? If so, you may need to enable the DHCP of the device so it can provide IP addresses for multiple devices to connect wirelessly. The WAG54G is an access point. It can only provide wireless and Internet access to one device at a time. For this, you may need to purchase a wireless router if you want to connect multiple devices (wired or wireless) and extend the wireless range using the WAG54G.
For more information about access points and routers, check this link out: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=b22772feb0f348f98a9c5d13e8469fca_192.xml&pid=80&re...
Information. Share it to learn.
Help, learn and share

Trouble setting up X with FreeBSD 7.1 on my Thinkpad T60 1951-FCG

Similar Messages

Maybe you are looking for