Trouble shooting the restore process iPad 2?
My ipad 2 is not taking the restore process, this is realy giving me a hard time. Please help!!
Try and force your iPad into Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times.
Similar Messages
-
My IPad 2 is locked with a passcode when I try to restore the ipad halfway through the restore process it is asking for a passcode I do not know the passcode and the IPad was never synced to a computer. Please help
Instructions can be found here.
http://support.apple.com/kb/ht1212
Make sure that you pay attention to the section at the very of the article that talks about having never synced your iPad with iTunes. You may need have to restore the iPad that way. -
please i am unable to restore my ipad due to error 3194.The restore process stalls when it gets to the point where the firmwarwe is being updated.error message 3194 comes up.please help me
http://support.apple.com/kb/TS3694#error3194
Unable to contact the iOS software update server gs.apple.com -
Have done all the trouble shooting connection but my iPad still can not get wifi connection
i have done all the trouble shooting connection but mu iPAd still can not get wifi connection
Hi Jo,
Each router is a little different but here are the basics: login to the router using the administrator account, should have that info from the installer, and then you should find something like security settings, or it may be advanced security. There will be a setting to the effect of limiting access, or it may say allow Mac address authentication, or admit the Mac addresses in the table...if that is switched on, you can just switch it off and that will allow any wireless device to attach. If you want to keep it on, then you have to enter the Mac address for the device you want to use for access. In the case of the iPad, go to Settings > General > About > WiFi Address (another way of saying Mac address). Enter that very long sequence in the router's Mac address acceptance table and that should take care of things.
Using the Mac address does not change any of the email settings, just limits attaching to the router in the first place.
If you are already getting email, you must be attaching already so this should not be an issue. If you are having email issues, such as receive but not send, you may not have the outgoing server set correctly: Settings > Mail > Account > Outgoing server name (usually an SMTP server) and you may have to go to the advanced settings to enter the outgoing password (normally the same as the account/incoming password) and then check to see if SSL is ON or OFF...most common email services say to set to OFF. -
HT6029 Having trouble restricting the restore function on an iPad through Apple Configurator
Having trouble restricting the restore function on an iPad through Apple Configurator
I cannot find the setting the allow/disable this feature.Configuration profiles do not allow you to apply a static IP address to a device.
Instead, it would be highly recommended to configure static IP addressing within the DHCP server itself. This would accomplish what you want without worrying about which proifle goes on what device, etc. Configurator can also export the MAC addresses to make life easier in setting this up.
Right click the 'All Devices' in the Supervise tab, click Export Info > Device Information > WiFi MAC Address. -
I need some helpful instructions on how to get my iPad back to normal because it says iPad is disabled connect to itunes. I've gone through the restoration process many times and it does not work. The iPad just seems to fail when its almost done restoring. Much help is needed please!
Hi LittleKritter13,
Thanks for visiting Apple Support Communities.
I recommend the steps in this article if your iPad does not complete the restore process:
Resolve iOS update and restore errors in iTunes
http://support.apple.com/kb/ts1275
If the issue persists, the method in this article may also help:
iOS: Unable to update or restore
http://support.apple.com/kb/ht1808
Best,
Jeremy -
I was in the process of restoring my ipad and an issue came up with itunes and it had to close. I reopened itunes but now my computer doesn't recognize the ipad as anything plugged in to my computer. I am unable to complete the restore process.
Hi kimbo934,
Welcome to the Support Communities!
The article below may be able to help you with this.
Click on the link to see more details and screenshots.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
I hope this information helps ....
Happy Holidays!
- Judy -
i need help!??? i just tried to update my ipod and now its making me restore it on itunes and it wont complete the restoring process. Its giving the warning that the updated software server couldn't be reached. Can anybody help????
Update Server
Try:
- Powering off and then back on your router.
- iTunes for Windows: iTunes cannot contact the iPhone, iPad, or iPod software update server
- Change the DNS to either Google's or Open DNS servers
Public DNS — Google Developers
OpenDNS IP Addresses
- Try on another computer/network
- Wait if it is an Apple problem -
Hello
My iphone 4S switches off after showing horizontal lines on the screen cutting through the apple logo during the restore process and then right after my iTunes shows the error 9 message, this happened 2 days ago when my phone just switched off unexpectedily and has been in this recovery mode since then. i have watched videos on Youtube and i have disabled Firewall before starting the process, i think i have done almost everything. please help anyone what do i do from here?
Just for interest sake i watched this video on youtube where this guy had the same problem but the difference is that he had it on an iPad. he opened the ipad up and did something on the ipad, it took less than a minute then his ipad worked.
I would appreciate it if someone would respond to this as fast as they can i am so stressed.
Regards
LwandoRead here:
http://support.apple.com/kb/ts3694#9
Error 9 is usually a security software issue. -
I sold my iPhone4, and I need to restore it before shipping it. The buyer has asked that I don't install iOS6. Is this possible? Does the restore process force iOS6 onto the phone? Before I backup/restore it, it has iOS5.1.1 installed.
Thanks in advance.
jjJust go to Settings>General>Reset>Reset all Content and Settings
-
When iOS 6.0 updating my iPhone and connecting my iPhone to iTunes the only option I have, is to restore my iPhone. But ufortunately, I did not back up my iPhone before the updating. Is there any way I can avoid the restoring process?
Once the Device is asking to be Restored with iTunes... it is too late to save anything...
To minimise loss... Connect to iTunes on the computer you Usually Sync with and Restore from the most recent Backup...
http://support.apple.com/kb/HT1414
Restore from Backup
http://support.apple.com/kb/ht1766 -
Trouble shooting the export function
I am a new user to CS4 Premiere 4.1.0 as part of my master suite program bought 2 weeks ago. I can't find any trouble shooting help or explanation of error messages in the program's help section; I have tried most of the trouble shooting steps (other than reinstalling the entire suite) from the knowledge base on the Adobe site without any success; and finally would like someone on this forum to rescue my newly installed Premiere from disaster. Here is my problem:
---- when exporting utilizing the media encoder; after exporting and clicking on the encoder to start , the program would come back with the following error message " PProheadless has encountered an error. [..\..\Src\Remote Import Module. Cpp-250]". I can't find any reference to this error code and how to fix it on the Adobe website. I have tried to fix it for days now without any results. Without being able to fix this my programs are useless to me.
Not finding any reference on the Adobe manual to the error code or how to trouble shoot the program is really demoralizing and disappointing to me. You can see PProHeadless as a program on the computer's hard drive but you won't find any reference to this program throughout the Adobe website.
For reference my hardware specs. are: i7 920 CPU, 6 G DDR3, Asus P6T professional work station main board, 160 G SSD SATA C-Drive, 1 tera byte SATA D and E drives, the GPU is nvidia GTX 285 with 1 GB ram, 1000 Watt power supply in a mini tower, plus Sony Blue ray, OS is Vista 64 premium. The computer is dedicated to editing video. All programs are loaded on C; the D drive is used as working space and virtual ram. E drive is for storage. The only other program running is Avast anti-virus program. The file exporting problem stays even when Avast is uninstalled. All the devise drivers are Vista 64 compatible. The computer is brand new; dedicated to Premiere - not even Microsoft word is loaded.
In addition to the above exporting problem, every time I switch between loaded programs such as between Premiere and Firefox, the cursor would stay in the "wait" mode, i.e. in a spinning circle, for about a minute before turning into an arrow in Premiere. It almost feels like Premiere has to reload the ram all over again; this is really annoying and time wasting.
If I have known of these issues, I would have bought a Mac Pro with Mac software in the first place.
I would really appreciate some help from friends and experts on this forum. Thank you.Do you have a dynamic or fixed dimension table?
Looks like you have a fixed dimension table here...
Using -> [*] is to specify each instances of that object inside the subform specified... Here if you have more than one PSI into Row5 it would work... But as I understand you have to write only Avg(Row3.PSI, Row4.PSI, Row4.PSI)
If you have a dynamic table and your row is only named Row1... each instances of the row would be Row1[0], Row1[1], Row1[2]
So in your Average function you would only write :
Avg(Row1[*].PSI) and it would return the average of each rows -
I have to restore my phone but it doesn't complete the restore process.
I did something wrong and it's making me restore my Iphone in Itunes. It goes through the process but once it gets to the restore process it goes a little bit and then just stops. I let it run for a couple hours but it never moved. I tried numerous times and each time it stopped. Please help. =(
Let your iPhone charge on the Wall Charger for 30 minutes and then try the Restore again. If still problems, and you are still under the 1 year Warranty or have AppleCare, then take iPhone to Apple for fix.
-
Error 9 pops up when trying to restore Ipod 5. The problem seems to be that my ipod disconnects during the restore process. My ipod is stuck in restore mode so I can't access its update serever. I have already updated my pc and its security settings. Is there anything else i can try?
Hello AS234,
This error is typically indicative of a conflict with installed security software.
Configure your security software
Check your security software and settings, which can block ports and prevent connection to Apple servers during update and restore.
Common errors: 2, 4, 6, 9, 1000, 1611, 9006, 9807, 9844. Sometimes as a result of this issue, a device might stop responding during the restore process.
Resolve specific iTunes update and restore errors
http://support.apple.com/kb/TS3694
Cheers,
Allen -
my phone has switched off for the second time this week, however when connecting to itunes the restore process wont complete. the error is 2006 however i have tried a number of USB cords, and none seem to be working.
I am in the noerthern [parts of australia and accessing an apple store is not possiable for another month. this is my only soucrce or telecommunication. please helpThis is what it says about error 2006
Error 2000-2009 (2001, 2002, 2005, 2006, 2009, and so on)
If you experience this issue on a Mac, disconnect third-party devices, hubs, spare cables, displays, reset the SMC, and then try to restore. If you are using a Windows computer, remove all USB devices and spare cables other than your keyboard, mouse, and the device, restart the computer, and try to restore. If that does not resolve the issue, try the USB issue-resolution steps and articles listed for Error 1604 above. If the issue persists, it may be related to conflicting security software. If the errors persist on another computer and known-good USB cable, the device may need service.
Maybe you are looking for
-
How do I move iTunes from a dead computer?
My iTunes currently resides on a dead computer (hard drive failure). How do I move iTunes to my laptop PC (Vista) without losing all of my music/videos (on iPod) or apps (iPhone)?
-
HP Photosmart 5520 printer no longer prints wireless
Hello. I recently got an xfinity cable modem with wireless. (Xfinity/comcast promoted it should be faster...I am seriously doubthing that!) Before this cable modem, I was printing okay with a Netgear router. Never an issue with it. Now with the co
-
Just in time creation of Result Set
I have this problem which is bugging me a lot. Actually I want to display some data on the browser by fetching it from the database. Now this result set could be quite big. So i would like to display on multiple pages like if there are 100 rows then
-
I heard a song on youtube and I tried to look it up on iTunes. It wasn't there. I googled it and somebody said it was only on the irish version of iTunes??? I'm not even sure what that is.
-
Reading Spool files from AS400 through JAVA Applications
Hi, i am trying to read spool fiels through my java application with the help of jt400.jar files,which is developed by IBM.When i try to display the content of the spool file the result is look like this and give some ideas to come out from these pro