Trouble with 30gb

When I plug my unit into my computer via the usb all I get is the spinning wheel and the please wait battery very low message. However, when it is plugged into the wall it shows the charging icon and becomes operational (meaning I can use it as normal), but will not charge.
Any ideas?
Thanks

I replaced the battery. I did the first one and I sure it was done right. It worked for about 6 months before this charging thing started. I also replaced the stereo jack. My next guess was the board but just wanted a few opinions before I dropped $75.00 on a new one.

Similar Messages

Trouble with 30Gb Photo

first time posting on here... I looked back through a few page to see if this issue had already been addressed.
A few days ago, my 30Gb iPod Photo started skipping songs on its own. So after resetting it, it lost all it's content. I've read a couple troubleshooting guides about the computer not recognizing the iPod, but still haven't yet found a way to restore my iPod.
When using the updater, I get many different error messages such as "Can't mount iPod" or "iPod service error"
I've tried re installing just about every iPod related software on my computer, as well as trying to Format my iPod (which I can't even do).
I'm hoping I don't have to send this out for service, as my warranty expired 6 days ago...
Can anyone help me out?
Thanks,
Alex
Windows XP

The Sad iPods icon or folder with an exclamation mark are the toughest problems to deal with, and must do a Restore in order to fix it. However, when your iPod is showing this icon, it is probably too late for your computer to recognize the iPod.
1. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
2. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
Still can't see your iPod?
Several things could keep iPod from appearing in iTunes or in the Desktop/Finder when you connect it to your PC/Mac. The most likely causes are listed below in logical order. Check from the top of the list to see if that is what's keeping iPod from appearing.
3. Try to wait 30 minutes while iPod is charging.
4. Try another known-good FireWire or USB through Dock Connector cable.
5. Try another known-good FireWire or USB port on your computer .
6. Try to disconnect all devices from your computer's FireWire and USB ports.
7. Windows users having trouble with their iPods should locate a Mac user. We've found that in many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
8. Try to do an Erase (Disk Utility) on a Mac computer or a format with a PC (Disk Management tool) but ensure you choose the right Drive (your iPod not your Hard Disk of your computer). You may need to plug and unplug your iPod with the computer for several attempts, and switching around Format and Restore, and hope out of sudden, it will get recognized.
9. Diagnostic mode solution – which I copied from a thread of a post from thinktwice
“Then I cam across this special Diganostics Mode that you can get to by resetting and then while the Apple is showing pressing the Select and backwards keys simultaneously. It bring up and weird Diagnostic utility witha a abunch of tests. Here is what I did
- I tried the 5in1 test and got and error on Firewire.
- I did the HDD R/W and surprisingly it passed.
- I went on to the HDD scan. This supposedly tkaes acouple of minute so I waited. I think 4-5 dots appeared then nothing. The iPod started to get hot. THe disk was spinning away. After a while the battery got very low. THis test chews up the battery. So I escaped out by resetting and went to connect it to a power source.
My USB was dangling out of my computer and I was too lazy to get the Firewire AC adapter thing going so I connected expecting the whole lockup thing with iTunes. Surprise. IT was recognized immediately and has been working like a champ. So go figure.
Details on Diag mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/index.shtml
10.Let me ask you a question, if an iPod with no iPod software with it. When your connect it with a computer, what would happen?
Yeah, the computer will treat it as a fresh external hard disk, which will get force mounted, the computer will ask you to format the iPod. It does not really matter the format is completed or not, the key is to erase (or partly) the corrupted iPod software on the iPod, after that the computer will recognize it.
Once it has been completed, eject your iPod, open the iPod updater and interestingly, you will able to do the Restore this time.
Base on the above, that's why I suggest Windows users who experience trouble with their iPods should locate a Mac machine or vice versa. PC computer will not recognize a Mac formatted iPod, but it will get mounted in an attempt to format your iPod.
But, if none of these steps address the issue, your iPod may need to be repaired. You can arrange for service at the iPod Service Website.
I have just read an interesting solution about the Sad iPod, it does make sense but the warranty will be waived once you open the iPod, I would not do it myself as I am not good on doing this
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Pictures and instructions of how to open the iPod case for battery replacement
http://www.kokopellimusic.us/KM_instructions.htm

Trouble with 30GB IPod

I have an older, 30GB IPod, it will not turn on. When I charge it, it come on but is frozen and shows a small picture of a lock in the upper left hand corner.
The wheel will not respond at all either? Any suggestions?

when turned on, try holding down the menu and center button at the same time until the ipod restarts itself

Trouble with 30GB ipod w/ video and trouble with itunes 7

here's the story: i just got a new ipod (the 30 GB with video). i got tired of my little shuffle with no screen.
so, i put my whole itunes library onto the ipod and everything was working fine. i loved it. then, i deleted some items from my itunes library on my laptop because it was taking up needed space on my hard drive, i figured this was fine, since i still have it on my ipod, and i can watch/listen to them anytime i want. But, when i went back later to put some new stuff on my ipod, 2 shows and 2 of my favorite podcast episodes were deleted from the ipod that i had put on before!
-i checked the manual, it said that i need to be in the manual mode instead of itunes/ipod automatically updating the ipod's library. i was transferring stuff manually, but it still got rid of some stuff on it's own.
the music was all still there, but a tv show episode, and 2 of my favorite video podcast episodes were deleted.
-Will this always be a problem everytime I hook it up to my laptop and want to add new stuff to my ipod? I don't even have half of the ipod filled. it says that I have 20Gb of free space.
i want to be able to keep stuff on my ipod that i will delete from my itunes library/hard drive. such as movies, tv shows, my favorite video podcast episodes. But at the same time, I want to be able to add new stuff. Is this Possible?? please help! is the ipod/itunes programmed to delete everything from the ipod that is not in the itunes library????

I figured it out myself: i chose the option manage manually.

Trouble with 5G 30Gb

I am having a lot of troubles with my ipod, firstly, it was unable to write songs to it through iTunes, a warning would come up saying there was som sort of corruption, so I tried updating my iPod. Once i had done that, iTunes said there was something wrong with my iPod saying that I should restore it and then update it again. I restored it, and now trying to update it, it freezes the computer, I've downloaded the new update from the Apple website and that does the same thing! It doesn't just temporarily freeze either, i've left it for 30 mins and still doesn't change. So now all i have is an ipod that shows the folder icon with this support page whenever I turn it on! Could somebody please help me!!!
5th gen video 30 Gb Windows XP

I'm having the same problem. My ipod has the folder with the exclamation point on it. It won't even reset. What's the deal?

Are people still having trouble with iPhone/HP Laptops?

Since I've had my Envy I've had no end of trouble with getting it and the iPhone to play nice. Any my search continues. So far, I have updated every bios, reinstalled Windows 7/iTunes many times, have restored the iPhone far more times than I care to remember and I am STILL having troubles with this thing. Having got through the Syncing issues with the PM55 chipset and iPhone I can now sync with my laptop. However all is not well as it would seem that I cannot sync my photo's. It doesn't matter if I have 0gb, 15gb or 30gb free, iTunes is telling me that there is not enough memory available. This error seems like an old one and there is even some info in the Apple KB but after following all that I still can't get it to sync my photo's.
Some info on my setup:
HP Envy 15 (all the latest drivers installed, bios F.24) Core i7-820, 8gb ram etc.
iPhone 32gb, ver 3.1.3
iTunes (whatever the latest one is)
I should add that I can sync my iPhone with an identical install of intunes on my vintage Quad core desktop PC, but as I use my Laptop a lot more (and have all my media, email, and contacts etc on it) I would prefer to sync to it.
Is there anything that I can do? Its very frustrating to have blown $4k on this equipment and it doesn't work...

Well I tried deleting the photocache but alas, no luck. I also tried syncing with just the photo's enabled, and it worked! So then I enabled my other media and that copied across too! I thought I was on a bit of a roll here, but now whenever I try and sync it will do one of 3 things:
iTunes will crash.
iTunes will indicate that there is not enough memory on the device (+9GB free)
iTunes will remove the iPhone from the sidebar (and my computer/disk management) even though it will continue to charge.
Interesting point to note is that it works fine (cable/iphone/itunes/media library) on my desktop and macbook. Still really disappointed that I cannot get these two to cooperate. Also still haven't got any contacts from outlook but that may not be related?

I have been having a lot of trouble with the latest itunes update and my ipod classic 80Gb i.e. being unable to sync songs, but now i have no files at all on my ipod, it is completely blank when i view it from my computer. I need help, please, anybody.

As it says above, i have been having a lot f trouble with my ipod classic and the latest itunes update, i was unable to sync songs or anything to it and have tried every conceivable 'fix' i could find. i have run an itunes diagnostic and the results are posted below. a major problem is that when i try and view my ipod through my computer it displays nothing at all on the ipod, no files or anything, this may be the problem but i have no idea how it has happened or how i could resolve it.
This ipod holds huge sentimental value and i am loathe to buy a new one! If anybody can help it is greatly appreciated, than kyou in advanced.
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
ASUSTeK Computer Inc. K50IJ
iTunes 11.1.5.5
QuickTime not available
FairPlay 2.5.16
Apple Application Support 3.0.1
iPod Updater Library 11.1f5
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 7.1.1.3
Apple Mobile Device Driver 1.64.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 0038B8600B98D1E0
Current user is not an administrator.
The current local date and time is 2014-03-21 16:52:39.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is supported.
Video Display Information
Intel Corporation, Mobile Intel(R) 4 Series Express Chipset Family
Intel Corporation, Mobile Intel(R) 4 Series Express Chipset Family
**** External Plug-ins Information ****
No external plug-ins installed.
Genius ID: 2fd81a1f13cf3ff25a8b4f0e8e725116
**** Device Connectivity Tests ****
iPodService 11.1.5.5 (x64) is currently running.
iTunesHelper 11.1.5.5 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Intel(R) ICH9 Family USB Universal Host Controller - 2934. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2935. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2936. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2937. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2938. Device is working properly.
Intel(R) ICH9 Family USB Universal Host Controller - 2939. Device is working properly.
Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293A. Device is working properly.
Intel(R) ICH9 Family USB2 Enhanced Host Controller - 293C. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.

Here is what worked for me:
My usb hub, being usb2, was too fast. I moved the wire to a usb port directory on my pc. That is a usb1 port which is slow enough to run your snyc.

Trouble with Toshiba built-in webcam: "unable to enumerate USB device"

I am running archlinux on a Toshiba Satellite L70-B-12H laptop, and having troubles with the Webcam. *Once in a while*, everything goes well and I get
# lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 004: ID 04f2:b448 Chicony Electronics Co., Ltd
Bus 003 Device 003: ID 8087:07dc Intel Corp.
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
# dmesg
[ 3433.456115] usb 3-1.3: new high-speed USB device number 4 using ehci-pci
[ 3433.781119] media: Linux media interface: v0.10
[ 3433.809842] Linux video capture interface: v2.00
[ 3433.826889] uvcvideo: Found UVC 1.00 device TOSHIBA Web Camera - HD (04f2:b448)
[ 3433.835893] input: TOSHIBA Web Camera - HD as /devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.3/3-1.3:1.0/input/input15
[ 3433.835976] usbcore: registered new interface driver uvcvideo
[ 3433.835977] USB Video Class driver (1.1.1)
Unfortunately, *most of the time* the camera seems invisible to my system, and I get
# lsusb
Bus 004 Device 002: ID 8087:8000 Intel Corp.
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 003: ID 8087:07dc Intel Corp.
Bus 003 Device 002: ID 8087:8008 Intel Corp.
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
(note the missing "04f2:b448 Chicony Electronics Co., Ltd" device), and
# dmesg
[ 480.104252] usb 3-1.3: new full-speed USB device number 4 using ehci-pci
[ 480.171097] usb 3-1.3: device descriptor read/64, error -32
[ 480.341235] usb 3-1.3: device descriptor read/64, error -32
[ 480.511375] usb 3-1.3: new full-speed USB device number 5 using ehci-pci
[ 480.578007] usb 3-1.3: device descriptor read/64, error -32
[ 480.748151] usb 3-1.3: device descriptor read/64, error -32
[ 480.918282] usb 3-1.3: new full-speed USB device number 6 using ehci-pci
[ 481.325196] usb 3-1.3: device not accepting address 6, error -32
[ 481.392091] usb 3-1.3: new full-speed USB device number 7 using ehci-pci
[ 481.798926] usb 3-1.3: device not accepting address 7, error -32
[ 481.799166] hub 3-1:1.0: unable to enumerate USB device on port 3
Searching on the web, most results I found lead to this page, where it is said that the problem is due to badly tuned overcurrent protection, and advocated that unplugging and switching off the computer for a little while gets things back into normal. This does not really work for me; the problem seems to occur more randomly, unfortunately with high probability (my camera is available after less than one boot out of ten).
I tried to ensure that the ehci-hcd module is loaded at boot with the ignore-oc option (with a file in /etc/module-load.d/), to no avail.
I also wrote a script which alternatively removes and reloads the ehci-pci driver until my device is found in lsusb. It is sometimes helpful, but usually not. And even when my device is found that way, it can only be used for a while before disappearing again.
Anyway, such a hack is unacceptable... So, my questions are:
is it indeed related to overcurrent protection ?
is there anything else I can try ?
should I file somewhere an other of the numerous bug reports about "unable to enumerate USB device" already existing ?
If of any importance, I am running linux 3.15.7, because at the time I installed my system, I couldn't get the hybrid graphic card Intel/AMD working under 3.16.
Last edited by $nake (2014-10-18 16:29:06)

uname -a
Linux libra 3.9.4-1-ARCH #1 SMP PREEMPT Sat May 25 16:14:55 CEST 2013 x86_64 GNU/Linux
pacman -Qi linux
Name : linux
Version : 3.9.4-1
Description : The linux kernel and modules
Architecture : x86_64
URL : http://www.kernel.org/
Licences : GPL2
Groups : base
Provides : kernel26=3.9.4
Depends On : coreutils linux-firmware kmod mkinitcpio>=0.7
Optional Deps : crda: to set the correct wireless channels of your country
Required By : nvidia
Optional For : None
Conflicts With : kernel26
Replaces : kernel26
Installed Size : 65562.00 KiB
Packager : Tobias Powalowski <[email protected]>
Build Date : Sat 25 May 2013 16:28:17 CEST
Install Date : Sun 02 Jun 2013 15:30:35 CEST
Install Reason : Explicitly installed
Install Script : Yes
Validated By : Signature

Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

Hi, i am having trouble with my mac mail account, i cannot send or receive any emails because of the server connection problems. Message says it could not be connected to SMTP server. Thanks in advance for your help.

Hello Sue,
I have an iPad 3, iPad Mini and iPhone 5S and they are all sluggish on capitalisation using shift keys. I hope that Apple will solve the problem because it is driving me crazy.
I find using a Microsoft Surface and Windows 8 phone, which I also have, work as well as all the ios devices before the ios 7 upgrade.
It has something to do with the length of time that you need to hold the shift key down. The shift key needs to be held longer than the letter key for the capitalisation to work. For some reason, this is a major change in the way we have learnt to touch type on computers. I am having to relearn how to type!
Michael

Trouble with OR in where clause

Hello,
I'm having trouble with execution speed. The problem seems to be with using OR in my where clause.
Here's the meat of the function where i_pledge_number is an input parm:
BEGIN
SELECT /*+ INDEX (pp) */ SUM(pp.prim_pledge_amount)
INTO return_amount
FROM
primary_pledge pp
WHERE
-- Get total if multiple allocations
pp.prim_pledge_number IN
(SELECT pc.pledge_number
FROM pledge_codes pc
WHERE pc.pledge_code_type = 'M'
AND pc.pledge_code = 'AC'
AND lpad(pc.pledge_comment,10,'0') = i_pledge_number)
-- Get total if single allocation
OR pp.prim_pledge_number = i_pledge_number;
RETURN return_amount;
END;
If I comment out either half of the OR statement (either the subquery or the pp.prim_pledge_number = i_pledge_number half) the function returns a value in .02 seconds. If I leave the OR in, it takes 2.764 seconds to execute?? Can someone please show me a better way (faster) to do this? I tried using nvl() around the subquery but couldn't get it to compile.
Thanks

These things are difficult to diagnose remotely, but here is something you can try....
SELECT */ SUM(pp.prim_pledge_amount)
INTO return_amount
FROM   primary_pledge pp
WHERE pp.prim_pledge_number IN (SELECT pc.pledge_number
                                 FROM pledge_codes pc
                                 WHERE pc.pledge_code_type = 'M'
                                 AND pc.pledge_code = 'AC'
                                 AND lpad(pc.pledge_comment,10,'0') = i_pledge_number
UNION ALL
SELECT i_pledge_number FROM dual)
   RETURN return_amount;
END;If that doesn't do anything (and it might well not) there are a large number of different ways we can recast this query. To save us further guessing please give us more details: execution plans, database version number, volumetrics.
Cheers, APC

A trouble with "LIKE" in a select statement

Hi!
I'm having trouble with "LIKE" in a select statement...
With Access I can make the following and everything works well:
SELECT name, birthday
FROM client
WHERE birthday LIKE '*/02/*';
but if try to do it in my application (it uses Access), it doesn't work - I just can't understand that!!!
In my application the "month" is always the currently month taken from the "System". Look what I'm doing...
String query1 = "SELECT name, birthday " +
          "FROM client " +
          "WHERE birthday " +
          "LIKE '*/" +
          pMonth +
          "/*' " +
          "ORDER BY birthday ASC ";
ResultSet rs = statement1.executeQuery(consulta1);
boolean moreRecords = rs.next();
The variable "moreRecords" is always "false", the query returns nothing although the table "client" has records that attend the query.
Please, anyone can help me?! It's a little bit urgent.
Thanks,
Katia.

Hi Katia,
I'll bet the problem lies with the characters you're using to escape the LIKE clause. You're using the ones that Access likes to see, but that's not necessarily what's built into the JDBC-ODBC driver class.
You can find out what the correct escape wildcard characters are from the java.sql.DatabaseMetaData.getSearchStringEscape() method. It'll tell you what to use in the LIKE clause.
I'm not 100% sure about your code. It doesn't use query1 anywhere. I'd do this:
String query = "SELECT name, birthday FROM client WHERE birthday LIKE ? ORDER BY birthday ASC";
PreparedStatement statement = connection.createStatement(query);
String escape = connection.getMetaData().getSearchStringEscape();
String test = escape + '/' + pMonth + '/' + escape;
statement.setString(1, test);
ResultSet rs = statement.executeQuery();
while (rs.hasNext())
// load your data into a data structure to pass back.
rs.close();
statement.close();Let me know if that works. - MOD

(Trouble printing) Trouble with connection between Macbook Pro and Hp Deskjet 1510.

Trouble with connection between Macbook Pro and Hp Deskjet 1510. (Nothing Prints).
I have a Macbook Pro and am having difficulty printing documents from ‘Pages' from my Hp Deskjet 1510. I have installed the necessary software for the printer and it is connected via USB. Every time I try to print the printer icon comes up as it should, 'printing' and then 'job completed' and then the icon disappears. (Nothing is printed.) I thought it might be something to do with Pages compatibility with the printer but exporting the document to Word or making it a PDF doesn’t change anything. I don’t have Microsoft Word on my computer. The scanner does work and when I printed a ‘Test Page’ that worked too.
Let me know if you know why this is happening.

With these settings the network now works flawlessly, however, when i have my ethernet cable plugged in, my internet access via my airport card(on the macbook pro) is no longer available. Hoping you can tell me why this would be with this info i've provided.
Educated guess. The networking devices have priorities as to which are used. The standard order is that Ethernet has a higher priority than Airport.
While your Ethernet is unplugged it is inactive and the Mac ignores it. Once you plug it in, the Mac sees that it is active and switches traffic to that interface.
I actually take advantage of this feature at home, but configuring my Airport and Ethernet with identical fixed IP addresses. Normally I'll use Airport, but if I'm copying a huge file and I want faster performance, I'll just walk my MacBook (previously iBook, previously Powerbook) over to my Ethernet switch and plug in my MacBook. Magically, the Mac detects that the Ethernet is active and continues the file transfer uninterrupted over the faster 100baseT Ethernet connection. When the transfer is finished, or if I really need to move back to the Comfy Chair, I unplug the Ethernet cable, and all activity reverts back to the Airport, all without disrupting any existing networking connections.
You on the other hand have totally different settings for your Ethernet and your Airport, so when you switch to Ethernet, you basically loose your Airport connections.
Something you can try:
System Preferences -> Network
Gear icon on the bottom left, next to the [+] [-] icons.
Select *Set Service Order...*
Now Drag the network interfaces into the perfer priority order you want. In this case put Airport above Ethernet.
NOTE: You may want to create a new Network Location for this, instead of messing with your normal home Location (which is most likely the default Automatic. That way you have your original you can always fall back to.

Edge Animation having troubles with iOS devices within Muse Site

Hi All! I've been creating a mobile version of my website www.rinkdesigns.com and have it all complete. I created an animation/navigation bar within Adobe Edge Animate and imported it into Muse. It functions AMAZINGLY on my Nexus 4 (Android) in Chrome but on a buddies iPhone 5 Chrome only loads about 3/4 of the animation/nav bar, in Safari the animation does not load at all and half of the page background does not load either. Please check out the preview site here http://rinkdesignsmobile.businesscatalyst.com/phone
Has anyone else been having animation/mobile troubles with iOS devices? Any hints as to how you fixed your errors would be extremely helpful! I also posted this question in the Muse forum and haven't gotten a response...
Thanks,
John

Or, how about this:
Does anyone know how to have Edge Animate objects that utilize "_top" in an open url trigger make the Muse site that they are a part of open a new window/tab with that action (as opposed to having it open the url in the current page, or using "_blank" in the trigger)?

Trouble with 3rd party VST installs for Garageband, can't find instruments

Hi,
I am having trouble with Audio Units for Garageband when installing 3rd party software, VSTs, loops, instruments. I have more issues with Logic Pro. I am hoping that it is the same underlying issue and that I am just missing something. I have the manuals (not great for troubleshooting). I am confused with some installs use User Library and others use the Computer Library. I do go to the mfgs sites for updates. The installs sometimes work as standalones but I don't see ALL of the components of the software in say Garageband or Logic. Mostly, I am missing the "instruments" and "loops" that I want to access within the DAW. Some examples:
• Here is some of the software I am talking about: East West sample libraries (Play and Native Instruments); Vienna Symphonic librarires; Sylenth1 (just last night); Sample Tank 2 and Total Workstation 2 from IK Multimedia and others.
• In GB I see the Audio Units for Vienna, Play, Sylenth, some of the IK Multimedia but NOT any instruments when I go to the "Sound Generator" -- I seem to be missing the instruments and loops. I see less AUs in Logic Pro. Some of these are VST instruments.
• Can I just drag-drop samples to the library folders to fix this?
• The plug-ins do not seem to work (though Sylenth1 worked for a single sound). When there is a standalone app (as in Sample Tank), I finally got the "sounds" to be reinstalled and loaded, those sounds/samples don't show up in any DAW.
• When and if the sounds/loops/samples show up in GB's "Instruments" section will I be able to tell that they belong to that particular software or library?
Thanks in advance.
John

Found the answer myself, it was simple:
• Select the Track
• Show the Instrument (info area)
• Click on Edit
• Click on the "Sound Generator" pop up field.
• At the bottom of the pop-up list, select from the Audio Units that you have installed. This is where you see "Sample Tank 2, Vienna Instruments..."
• NEXT -- IMPORTANT: CLICK ON THE PICTURE next to the Sound Generator pop-up field.The AU unit loads up, the interface pops up, you load up the instruments in this AU Unit. You do NOT see the sounds from the AU unit in the normal Apple instrument list.
This was not intuitive but once you know it, fairly simple.
Still, the devil is in the details -- more questions on the way.

I'm having trouble with something that redirects Google search results when I use Firefox on my PC. It's called the 'going on earth' virus. Do you have a fix that could rectify the vulnerability in your software?

I'm having trouble with a virus or something which affects Google search results when I use Firefox on my PC ...
When I search a topic gives me pages of links as normal, but when I click on a link, the page is hijacked to a site called 'www.goingonearth.com' ...
I've done a separate search and found that other users are affected, but there doesn't seem to be a clear-cut solution ... (Norton, McAfee and Kaspersky don't seem to be able to detect/fix it).
I'd like to continue using the Firefox/Google combination (nb: the hijack virus also affects IE but not Safari) - do you have a patch/fix that could rectify the vulnerability in your software?
thanks

''' "... vulnerability in your software?" ''' 
And it affects IE, too? Ya probably picked up some malware and you blame it on Firefox.
Install, update, and run these programs in this order. They are listed in order of efficacy. '''''(Not all programs detect the same Malware, so you may need to run them all to solve your problem.)''''' These programs are all free for personal use, but some have limited functionality in the "free mode" - but those are features you really don't need to find and remove the problem that you have. 
''Note: If your Malware infection is bad enough and you are mis-directed to URL's other than what is posted, you may have to use a different PC to download these programs and use a USB stick to transfer them to the afflicted PC.''
Malwarebytes' Anti-Malware - [http://www.malwarebytes.org/mbam.php] 
SuperAntispyware - [http://www.superantispyware.com/] 
AdAware - [http://www.lavasoftusa.com/software/adaware/] 
Spybot Search & Destroy - [http://www.safer-networking.org/en/index.html] 
Windows Defender: Home Page - [http://www.microsoft.com/windows/products/winfamily/defender/default.mspx] 
Also, if you have a search engine re-direct problem, see this: 
http://deletemalware.blogspot.com/2010/02/remove-google-redirect-virus.html
If these don't find it or can't clear it, post in one of these forums for specialized malware removal help: 
[http://www.spywarewarrior.com/index.php] 
[http://forum.aumha.org/] 
[http://www.spywareinfoforum.com/] 
[http://bleepingcomputer.com]

Trouble with 30gb

Similar Messages

Maybe you are looking for