Trouble with a wrt160n v2 router

I have been having trouble setting up the internet connection on my router, I get a wifi connection but not able to get internet through the wifi.  The ISP has told me that the settings are ETHoA, RFC 1438, WAN IP - Auto, QoS -UBR, Bridged, VPI 8, VCI 35.
However, I am not able to find the settings where I am able to input these.  
Any advice would be appreciated.
Thank you

CR_ERTW wrote:
I have been having trouble setting up the internet connection on my router, I get a wifi connection but not able to get internet through the wifi.  The ISP has told me that the settings are ETHoA, RFC 1438, WAN IP - Auto, QoS -UBR, Bridged, VPI 8, VCI 35.
However, I am not able to find the settings where I am able to input these.  
Any advice would be appreciated.
Thank you
To Configure your router you need to access the set-up page of the linksys router. You need to connect first a computer to the router to any of the numbered ports.
> check the IP address. Default gateway will be the IP address of the router. ( 192.168.1.1)
> You will be prompt for the Username and Password by default Password is admin.
> who is your ISP? If its cable - go to the sub tab MAC ADDRESS CLONE under the SETUP tab and enable and clone the PC's MAC. After doing that go to the STATUS tab and check if you were able to see an INTERNET IP ADDRESS or better yet check if online.
> To Configure the WIRELESS SETTINGS go to the WIRELESS TAB and you can personalized everything from there.
Hope it helps a little bit.
♥'s TECHNICAL

Similar Messages

  • Trouble with setting up my router...

    I've set up plenty of routers in my life, i've built plenty of computers as well, my knowledge of computers and networking isn't that bad you can say. I was setting up my girlfriends router and was having trouble getting an internet connection. When the modem was hooked up to her computer it was fine, and a website could be accessed. When it is plugged in through the router, you can't access a website. The computer is detecting the connection (Local Area Connection 2 is plugged in) but the interent connection is not being detected. Any suggestions. To avoid this: all wires are assembled correctly! Thanks =)

    I have the same problem here as described above...my router is the linksys wrt150N and my service provider is cox cable...my wireless adapter is intel WiFi link 4965AGN, while the regular connection is through realtek RTL8101E Family PCI-E Fast Ethernet NIC (NDIS 6.0).
    thanks for any solution you can provide...
    DC

  • Trouble with logging into my router

    I'm running a MI424-WR rev f router and when I log into 192.168.1.1, I can enter the admin login name, but I cannot enter the password. For every letter I type, at least two characters appear. I used to be able to copy and past the password into the form, but now that doesn't work, either (it adds another character). 
    This happens with every browser I have (chrome, safari, firefox, and camino). Anyone else seen this?
    thanks!
    -M

    You can ignore the number of characters displayed.  This is a security feature that is suppose to confuse any one watching over your shoulder as to how long your password is.
    Password should default to matching the serial number displayed on your router.  The router when reset may use "password" as the password and installers use to change it to "password1"

  • Trouble with a Linkysys Wireless-N Router WRT-160W After a black out

    So like the subject says I am having trouble with the router. Last night there was a major storm in my town and the power and cable were out for hours. When it came back (it was only for about twenty minutes) the network was there but I was not able to connect to it from any of my computers. The desktop however that was hardlined to it works fine on the internet. I've tried restarting the modem the computers, and the router, pushing the reset buttons, even holding the reset button to the point it made the router act like its being used for the first time and creating a new network but I still can't connect to it. I only bot this router a couple of months ago so I'd hate to have to buy a new one.
    Any help would be appreciate.
    Thanks.

    Are you using Cable connection or DSL connection ?
    If you are using cable connection then follow this link and if you are using DSL connection then follow this link to configure your router. This should fix the issue for you.

  • Serious troubles with my WRT110 router

    Hello! This problem all started when I upgraded the machine I'm typing this on to Windows 7 Ultimate.  No matter what I did, it would not connect to the existing network. I finally found a way to get it to connect by entering the router's PIN number, but it effectively created an entirely new network. My problem lies here. I can create new open networks just fine, but if I try to create an encrypted network it will not work -- the computer won't even detect the router. I need an encrypted network because I'm required by law to have one in my line of work, and I have no idea how to set it up. The network is comprised of this machine I'm using, a Macbook, and a TiVo DVR, as well as my laptop which is in for repairs. I might also add that I'm having trouble with the software that came with the router. Ideally, I'd have a secure network with an easily memorable password so other machines can join. I have spent many hours on this and I'm truly at a loss, and some step by step instructions would be tremendously appreciated. Thanks in advance,
    ~Eric
    Solved!
    Go to Solution.

    1. You should always access the web interface through a wired connection. Through a wireless link you may accidentally configure the router of your neighbor. And of course you should also never make changes on the wireless settings through a wireless link. Thus, always use a wired connection only for this purpose.
    2. It does not affect your network as it is. It only changes the router configuration. If you change the wireless configuration of the router it will, of course, affect all existing wireless links to the router (if any).
    3. You should not choose a "easily memorable password". That's always a bad idea. The wireless passphrase is usually only entered once on each wireless device to establish the connection to the router. The wireless device usually remembers the passphrase. Thus it is better to choose a very strong passphrase, e.g. a random generated longer passphrase. That is much more secure.

  • Trouble with advertise a route BGP from VRF on Cisco IOS 7600

    Hi
    the diagram especifie the actually operating network
    we try to advertise the network 172.16.161.6 to Nortel devices and Cisco devices on cisco AS 2005 and 64912, if we are staying look the routing table on cisco 7600 the network 172.16.161.6 is know it
    Success rate is 100 percent (5/5), round-trip min/avg/max = 20/24/28 ms
    cisco 7600#trace                            
    cisco 7600#traceroute vrf data 172.16.161.6
    Type escape sequence to abort.
    Tracing the route to 172.16.161.6
      1 189.1.11.5 [MPLS: Labels 581/730 Exp 0] 24 msec 24 msec 24 msec
      2 172.16.12.73 [MPLS: Label 730 Exp 0] 36 msec 28 msec 36 msec
      3 172.16.12.74 20 msec 20 msec 24 msec
      4 172.16.14.10 64 msec 20 msec 20 msec
      5 172.16.19.9 20 msec 24 msec 20 msec
      6 172.16.161.6 24 msec 20 msec 24 msec
    PE_CAR_1#ping vrf data 172.16.161.6     
    Type escape sequence to abort.
    Sending 5, 100-byte ICMP Echos to 172.16.161.6, timeout is 2 seconds:
    but the devices Nortel on AS 64912 on routing tables don´t know the networ 172.16.161.6
    the difference on cisco 7600 that know both AS 64912 and 2005 is this one:
    configuration on Cisco Router 7600
    router bgp 2006
    bgp router-id 172.16.110.97
    bgp log-neighbor-changes
    bgp graceful-restart restart-time 120
    bgp graceful-restart stalepath-time 360
    bgp graceful-restart
    neighbor 172.16.10.41 remote-as 64912
    neighbor 172.16.10.41 description PP-A6
    neighbor 172.16.11.233 remote-as 64912
    neighbor 172.16.11.233 description PP-2TE2
    neighbor 172.16.12.73 remote-as 2005
    neighbor 172.16.12.73 description PE_MEX_1
    neighbor 172.16.12.73 fall-over bfd
    neighbor 172.16.13.9 remote-as 2005
    neighbor 172.16.13.9 description PE_MEX_3
    neighbor 172.16.13.9 fall-over bfd
    neighbor 172.16.13.77 remote-as 2005
    neighbor 172.16.14.6 remote-as 64512
    neighbor 172.16.14.10 remote-as 64512
    neighbor 172.16.16.26 remote-as 64982
    neighbor 172.16.16.26 description INTERNET-2
    neighbor 172.16.16.30 remote-as 64982
    neighbor 172.16.16.30 description INTERNET-1
    address-family ipv4
      neighbor 172.16.10.41 activate   (conexion to Nortel Devices)
      neighbor 172.16.10.41 route-map AS-PATH-MAN in
      neighbor 172.16.10.41 route-map REDES-WAN->MAN out
      neighbor 172.16.11.233 activate   (conexion to Nortel Devices)
      neighbor 172.16.11.233 route-map AS-PATH-MAN in
      neighbor 172.16.11.233 route-map REDES-WAN->MAN out
      neighbor 172.16.12.73 activate
      neighbor 172.16.12.73 route-map REDES-WAN-PE_MEX_1 in
      neighbor 172.16.12.73 route-map DEFAULT-ROUTE out
      neighbor 172.16.13.9 activate  (conexion to Cisco 7600 Devices)
      neighbor 172.16.13.9 route-map REDES-WAN-PE_MEX_3 in
      neighbor 172.16.13.9 route-map DEFAULT-ROUTE out
      neighbor 172.16.13.77 activate
      neighbor 172.16.13.77 route-map DEFAULT-ROUTE out
      neighbor 172.16.14.6 activate  (conexion to ASR 9000)
      neighbor 172.16.14.6 route-map default out
      neighbor 172.16.14.10 activate (conexion to ASR 9000)
      neighbor 172.16.14.10 route-map default out
    the difference that look it from routes to know Nortel devices an Cisco Devices is the sollow on Cisco 7600
    Cisco 7600#sho ip bgp 150.151.1.250
    BGP routing table entry for 150.151.0.0/16, version 5612717
    Paths: (2 available, best #1, table default)
    Multipath: eBGP
      Advertised to update-groups:
         2          4        
      2005
        172.16.13.9 from 172.16.13.9 (150.220.250.5)
          Origin IGP, localpref 300, valid, external, best
          Community: 100:22
          Extended Community: RT:100:22
      2005
        172.16.12.73 from 172.16.12.73 (150.220.250.1)
          Origin IGP, localpref 260, valid, external
          Community: 100:22
          Extended Community: RT:100:22
    Cisco 7600#sho ip bgp 172.16.161.6
    BGP routing table entry for 172.16.161.6/32, version 6133620
    Paths: (2 available, best #2, table default)
    Multipath: eBGP
      Not advertised to any peer
      64512 64513
        172.16.14.6 from 172.16.14.6 (172.16.14.1)
          Origin incomplete, localpref 100, valid, external, multipath
          Extended Community: RT:64512:64513
      64512 64513
        172.16.14.10 from 172.16.14.10 (172.16.14.2)
          Origin incomplete, localpref 100, valid, external, multipath, best
          Extended Community: RT:64512:64513
    NOT advertised to any peer
    if we looking on ASR the vrf GAT the network is advertised but on vrf CAMPUS not
    RP/0/RSP0/CPU0:ED_MEX_1#sho bgp vrf CAMPUS 172.16.161.6
    Mon May 20 12:58:03.516 UTC
    BGP routing table entry for 172.16.161.6/32, Route Distinguisher: 64512:64513
    Versions:
      Process           bRIB/RIB  SendTblVer
      Speaker                 20          20
        Local Label: 16004
    Last Modified: May 17 17:24:29.877 for 2d19h
    Paths: (1 available, best #1)
      Not advertised to any peer
      Path #1: Received by speaker 0
      Not advertised to any peer
      64513
        172.16.19.5 from 172.16.19.5 (172.16.162.4)
          Origin incomplete, metric 110, localpref 100, valid, external, best, group-best, import-candidate
          Received Path ID 0, Local Path ID 1, version 20
          Extended community: RT:64512:64513
    but the vrf GAT:
    RP/0/RSP0/CPU0:ED_MEX_1#sho bgp vrf GAT 172.16.161.6   
    Mon May 20 12:58:52.909 UTC
    BGP routing table entry for 172.16.161.6/32, Route Distinguisher: 64512:2006
    Versions:
      Process           bRIB/RIB  SendTblVer
      Speaker                 30          30
    Last Modified: May 17 17:24:29.877 for 2d19h
    Paths: (1 available, best #1)
      Advertised to CE peers (in unique update groups):
        172.16.14.5    
      Path #1: Received by speaker 0
      Advertised to CE peers (in unique update groups):
       172.16.14.5    
      64513
        172.16.19.5 from 172.16.19.5 (172.16.162.4)
          Origin incomplete, metric 110, localpref 100, valid, external, best, group-best, import-candidate, imported
          Received Path ID 0, Local Path ID 1, version 30
          Extended community: RT:64512:64513
    Any idea for this trouble, we try to advertise the extend community but nothing.
    the configuration on ASR is the follow:
    router bgp 64512
    bgp router-id 172.16.14.1
    address-family ipv4 unicast
    address-family vpnv4 unicast
    vrf GAT
      rd 64512:2006
      address-family ipv4 unicast
       redistribute connected
       redistribute static
      neighbor 172.16.14.5
       remote-as 2006
       address-family ipv4 unicast
        send-community-ebgp
        route-policy pass-all in
        route-policy pass-all out
        send-extended-community-ebgp
    vrf CAMPUS
      rd 64512:64513
      address-family ipv4 unicast
       redistribute connected
       redistribute static
      neighbor 172.16.19.5
       remote-as 64513
       address-family ipv4 unicast
        route-policy pass-all in
        route-policy pass-all out
    we only put send-extended-community-ebgp only on vrf GAT.
    Best Regards

    Hi Harold thanks for your comment
    We do it your recommendation and put on AS 64912 routes a route-map for identify the traffic IN on interface the finally configuration on cisco 7600 is:
    router bgp 2006
    bgp router-id 172.16.110.97
    bgp log-neighbor-changes
    bgp graceful-restart restart-time 120
    bgp graceful-restart stalepath-time 360
    bgp graceful-restart
    neighbor 172.16.14.6 remote-as 64512
    neighbor 172.16.14.6 description EDGE_MEX_1
    neighbor 172.16.14.10 remote-as 64512
    neighbor 172.16.14.10 description EDGE_MEX_2
    address-family ipv4
      no synchronization
      neighbor 172.16.14.6 route-map REDES_CAMPUS in
      neighbor 172.16.14.6 route-map default out
      neighbor 172.16.14.10 activate
      neighbor 172.16.14.10 route-map REDES_CAMPUS in
      neighbor 172.16.14.10 route-map default out
      neighbor 172.16.16.26 activate
    with the follow route maps:
    ip extcommunity-list standard GAT permit rt 64512:64513
    ip bgp-community new-format
    ip community-list standard REDES-GAT permit 64512:2006
    route-map REDES_CAMPUS permit 430
    match extcommunity GAT
    set local-preference 250
    set community 64512:2006 additive
    set extcommunity rt  64512:64513 additive
    route-map REDES-WAN->MAN permit 1600
    match community REDES-GAT
    with this information the routes advertise on neighbord know the loopback 172.16.161.6
    GW_MEX_2#sho ip bgp neighbors 172.16.11.233 advertised-routes
    BGP table version is 6160029, local router ID is 172.16.110.97
    Status codes: s suppressed, d damped, h history, * valid, > best, i - internal,
                  r RIB-failure, S Stale
    Origin codes: i - IGP, e - EGP, ? - incomplete
       Network          Next Hop            Metric LocPrf Weight Path
    *> 1.0.0.1/32       172.16.12.73                  300      0 2005 ?
    *> 1.0.0.2/32       172.16.12.73                  300      0 2005 ?
       Network          Next Hop            Metric LocPrf Weight Path
    *> 172.16.140.72/32 172.16.13.9                   300      0 2005 ?
    *> 172.16.141.22/32 172.16.12.73                  250      0 2005 ?
    *> 172.16.141.61/32 172.16.12.73                  250      0 2005 i
    *> 172.16.141.71/32 172.16.12.73                  250      0 2005 i
    *> 172.16.142.0/27  172.16.13.9                   300      0 2005 ?
    *> 172.16.142.32/27 172.16.13.9                   250      0 2005 ?
    *> 172.16.144.0/27  172.16.13.9                   300      0 2005 ?
    *> 172.16.146.1/32  172.16.13.9                   300      0 2005 65451 i
    *> 172.16.150.0/27  172.16.12.73                  250      0 2005 ?
    *> 172.16.152.0/27  172.16.13.9                   300      0 2005 ?
    *> 172.16.152.32/28 172.16.13.9                   300      0 2005 ?
    *> 172.16.155.1/32  172.16.13.9                   300      0 2005 ?
    *> 172.16.161.1/32  172.16.14.6              0    250      0 64512 ?
    *> 172.16.161.6/32  172.16.14.10             0    250      0 64512 ?
    Thanks for your cooperation
    Best Regards

  • Hard wired PC losing internet connection with WRT160N V2 Router

    I'm new to routers and I just added a WRT160N (V2) router.  The wireless connection through my laptop is great. However, I have 1 PC physically connected to the router. The internet connection is sporadic on this PC. I have high speed "wireless" internet service and sometimes you click on the internet or check e-mail and there is no internet connection. It seems to be after the PC has sat idle for a while. When you click the internet, the PC icon on the router does not even blink - its like the PC and router are not talking. If it does connect, the connection is great. Any help would be appreciated!
    Solved!
    Go to Solution.

    There is a known issue with intermittent connectivity and the Build 11 firmware for the WRT160N V2. Build 11 is the current firmware on the Linksys site. Check to see if you have Build 11 if your router is a V2.
    Downgrading to Build 8 is generally accepted to correct these issues, however Linksys have indicated to several people they do not have the build 8 firmware to give to end users.
    This is ONLY for WRT160N V2 routers. This firware will not work on WRT160N V1.
    You can find it at http://audipages.com/router/
    Follow the dowload and firmware downgrade instructions on that page.
    Tomato 1.25vpn3.4 (SgtPepperKSU MOD) on a Buffalo WHR-HP-G54
    D-Link DSM-320 (Wired)
    Wii (Wireless) - PS3 (Wired), PSP (Wireless) - XBox360 (Wired)
    SonyBDP-S360 (Wired)
    Linksys NSLU2 Firmware Unslung 6.10 Beta unslung to a 2Gb thumb, w/1 Maxtor OneTouch III 200Gb
    IOmega StorCenter ix2 1TB NAS
    Linksys WVC54G w/FW V2.12EU
    and assorted wired and wireless PCs and laptops

  • ISSUE With my WRT600N Wireless Router --

    Hello, I am having trouble with my Wireless Router. It is the WRT600N model Linksys Router and the issue I am specifically having is my wireless access. I have several devices which access wirelessly and am starting to have more and more issues of late, not sure why...?
    I was wondering how to configure each device accessing my wireless net individually as I have Network MAgic asnd have seen a couple of the items on my network with the same ip addresses. I would like to assign a number to each device and see if that eliminates the issues I have been experiencing..?
    I have looked through these question pages and have not found the answer I was looking for so I hope this has not been asked before. I also saw a post that kind of caught my interest and it was regarding using two WRT600N's routers together for better range etc. I have an issue with raqnge on my system and have an old WRT54 Router and would like to know if I could do the same thing with this and incorporate this router into my system as a wireless access point (WAP) only. If this is possible, what would the steps be to accomplish this...
    My main issue I chose to writer about here was recently experienced when I got an Ipad and my Ipad has issues remaining connected to my WRT600N Router and I checked my network program and noticed that it was assigned the samw IP address as one of my boys X-Boxes. I believe currently we have approximately 9-11 devices that periodically connect wirelessly to my network. Some devices are PSP's and only occassionally connect and I have NEVER seen all the devcices connect at the same time. I believe the max at once would be approximately 5-6 devices.  Is this too many at once...?  Is the router overloaded with the amount of devices I have connected...?
    Please let me know what you would recommend for my situation,
    Darius Taylor
    [email protected]

    2 wireless routers can not communicate wirelessly with each other.
    You need to connect cable between 2 routers and use the second wireless router as access point.
    Follow this link to connect Linksys router to another router.
    Some of your devices are getting same IP address. This might be the issue with DHCP server of the router. You can try DHCP reservation on the router so that each device will get unique IP address.

  • Trouble with DNS set up

    Hello !
    I've got a real trouble with my dns configuration... and i can't understand! so, i need some help....
    well, qutie newbie in mac os server, i run in on a G4, and i had not noticed any trouble until i've decided to run open directory as a master with LDAP, wanting to have a kerberos protection for the users.
    Kerberos doesn't want to play with me !
    I've been in console mode to have a look, and, actually i've seen this :
    "Oct 17 11:31:08 wakan servermgrd: servermgr_dns: no name available via DNS for 192.168.0.109
    Oct 17 11:31:08 wakan servermgrd: servermgr_dns: no reverse DNS entry for server, various services may not function properly"
    Ok... my DNS has a trouble... but i don't know how to fix it ! Is there anybody in this world who can help me?
    I don't want to have a real DNS for my little server... but i understand that my config is not good. I can understand that having a caching DNS can improve the quality of my config, and, in other hand that it is necessary for having the services of OSX server in an effeciant way, but i don't know the way and the parameters i've to put in my config to fix it.
    Now, just some words on my config...
    First, i've got an adress provided by my FAI (the frenchy workd for ISP, i think) is "193.252.209.135". This adress is set on a d-link modem router via PPOE. The DNS of my provider (wanadoo.fr) are 80.10.246.1 and 80.10.246.132.
    After this there is my G4 With mac osX server.
    • en0, the "extenal gate" and the internal ethernet on the computer is plug on the modem with the adress "192.168.0.109". the router is set on "192.168.0.1". the dns are 80.10.246.1 and 80.10.246.132.
    • en1, the "internal gate" for the network, an PCI card in the computer, has the parameters : adress "192.168.3.1", subnet "255.255.255.0", router "192.168.3.1". no dns records. (no VPN service for the moment). After this, i've a switch for the macs behind the server. (without any link agregation)
    All those parameters have been set by the gateaway assistant.
    And now the parameters inside the admin server :
    DHCP : en1 - adress from 192.168.3.2 to 192.168.3.254, name 192.168.3. no static card. Router 192.168.3.1. No name for domaine by defaut, name servers 80.10.246.1 and 80.10.246.132 No LDAP, no WINS.
    DNS : No zone transfert, recursivity is ON. No zone records.
    NAT : set on full, Transfert and Network Address Translation.
    When i've been on the terminal, i had those information:
    "wakan:~ st$ sudo changeip -checkhostname
    Password:
    Primary address = 192.168.0.109
    Current HostName = wakan.local
    The DNS hostname is not available, please repair DNS and re-run this tool."
    All my "main" services are working fine (AFP, Firewall, DHCP, DNS, Update) Open Directory is running without Kerberos. By the way, all the macs after the G4server can have a corect access to internet, and share information via LDAP of Open Directory, but i've to say that, a couple of days later, a friend of mine, who has a PC computer, can't have a DHCP dynamic address when he plug on my little network. I think that it is an other trouble, and i've decided to have e look to this later... but if someone knows how to resolve it...
    So here begins the nightmare for me... so if anybody can help me... i realy need some help to fix this mystery!!!
    Special thanks!

    As the router modem is already doing NAT why use NAT in the server?
    If you want to use OpenDirectory and other services you should/need to set up the DNS correctly using the server's private IP (and others in the same range the server is setup with). The domainname used internally can be different than your public one.
    And then use the server as the only DNS for you LAN clients and the server itself. Forwarders (your ISP DNSes) in /etc/named.conf usually speeds up lookups of external addresses (also turning off IPv6 can help that too).

  • Trouble with Safari - it keeps shutting down - all because I tried to get rid of MacKeeper

    trouble with Safari - it keeps shutting down - all because I tried to get rid of MacKeeper ad - after I install what I thought was an update since I already had MacKeeper, it would not allow me to continue without buying the new one. Make a long story short I switch to Firefox and deleted as much as I could of Safari (files, preferences etc) Now I'm at OS Yosemite X 10.10.2 and would like to get Safari up and running again - I've searched for Adware in applications etc but could not find it. Found what to do from the community, but before I go that route...Do I have to know where or if I actually have this spyware?    And if I were to reinstall  Maveric - would my files and such be undisturbed?  so that only Safari would be replaced?    I"M LOST .... (as if you couldn't tell)
    I've been working with Mac for 30 years or more and although I'm hands on taught the only thing I lack is the newer "buzz words" so if you can help me out - please make it simple ??  thanks

    There is no need to download anything to solve this problem.
    You may have installed one or more of the common types of ad-injection malware. Follow the instructions on this Apple Support page to remove it. It's been reported that some variants of the "VSearch" malware block access to the page. If that happens, start in safe mode by holding down the shift key at the startup chime, then try again.
    Back up all data before making any changes.
    One of the steps in the article is to remove malicious Safari extensions. Do the equivalent in the Chrome and Firefox browsers, if you use either of those. If Safari crashes on launch, skip that step and come back to it after you've done everything else.
    If you don't find any of the files or extensions listed, or if removing them doesn't stop the ad injection, ask for further instructions.
    Make sure you don't repeat the mistake that led you to install the malware. It may have come from an Internet cesspit such as "Softonic" or "CNET Download." Never visit either of those sites again. You might also have downloaded it from an ad in a page on some other site. The ad would probably have included a large green button labeled "Download" or "Download Now" in white letters. The button is designed to confuse people who intend to download something else on the same page. If you ever download a file that isn't obviously what you expected, delete it immediately.
    Malware is also found on websites that traffic in pirated content such as video. If you, or anyone else who uses the computer, visit such sites and follow prompts to install software, you can expect more of the same, and worse, to follow. Never install any software that you downloaded from a bittorrent, or that was downloaded by someone else from an unknown source.
    In the Security & Privacy pane of System Preferences, select the General tab. The radio button marked Anywhere  should not be selected. If it is, click the lock icon to unlock the settings, then select one of the other buttons. After that, don't ignore a warning that you are about to run or install an application from an unknown developer.
    Still in System Preferences, open the App Store or Software Update pane and check the box marked
              Install system data files and security updates (OS X 10.10 or later)
    or
              Download updates automatically (OS X 10.9 or earlier)
    if it's not already checked.

  • Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T

    Trouble with CCME 4 and VIC2-2FXO; IOS 12.4(9)T
    I am having trouble making outgoing call or answering incoming call.
    When I try to call out from my IP 7961 phone, it fails with the message "unknown number".
    For incoming call, it rings but when I pick up the call nothing happens,
    Put the receiver back on hook, the phone carries on ringing. I am in UK
    and just trying to set up test system with one analogue line. Any help will
    be most appreciated. My config of the 2811 router is posted below. All calls ineternally works fine.
    Thank you for your help.
    hostname Test-CME
    ip cef
    no ip dhcp use vrf connected
    ip dhcp excluded-address 10.10.10.1 10.10.10.10
    ip dhcp excluded-address 10.139.139.1 10.139.139.10
    ip dhcp pool host
    network 10.10.10.0 255.255.255.0
    default-router 10.10.10.1
    option 150 ip 10.10.10.1
    ip dhcp pool data
    network 10.139.139.0 255.255.255.0
    default-router 10.139.139.1
    dns-server 10.139.139.5
    voice-card 0
    no dspfarm
    voice service voip
    allow-connections h323 to h323
    allow-connections h323 to sip
    allow-connections sip to h323
    allow-connections sip to sip
    supplementary-service h450.12
    h323
    sip
    header-passing
    registrar server expires max 3600 min 3600
    interface FastEthernet0/1
    no ip address
    no ip mroute-cache
    duplex auto
    speed auto
    no shut
    interface FastEthernet0/1.2
    description ** Data VLAN **
    encapsulation dot1Q 2
    ip address 10.139.139.1 255.255.255.0
    interface FastEthernet0/1.3
    description ** Voice VLAN **
    encapsulation dot1Q 3
    ip address 10.10.10.1 255.255.255.0
    ip http server
    ip http authentication local
    no ip http secure-server
    ip http path flash:
    tftp-server flash:S00104000100.sbn
    tftp-server flash:TERM41.7-0-3-0S.loads
    tftp-server flash:term61.default.loads
    tftp-server flash:term41.default.loads
    tftp-server flash:CVM41.2-0-2-26.sbn
    tftp-server flash:cnu41.2-7-6-26.sbn
    tftp-server flash:Jar41.2-9-2-26.sbn
    tftp-server flash:term70.default.loads
    tftp-server flash:term71.default.loads
    tftp-server flash:cnu70.2-7-6-26.sbn
    tftp-server flash:Jar70.2-9-2-26.sbn
    tftp-server flash:TERM70.7-0-3-0S.loads
    tftp-server flash:CVM70.2-0-2-26.sbn
    control-plane
    voice-port 0/3/0
    connection plar opx 202
    caller-id enable
    dial-peer voice 1 pots
    incoming called-number .
    destination-pattern 9T
    port 0/3/0
    telephony-service
    load 7914 S00104000100
    load 7941 TERM41.7-0-3-0S
    load 7961 TERM41.7-0-3-0S
    load 7970 TERM70.7-0-3-0S
    max-ephones 20
    max-dn 40
    ip source-address 10.10.10.1 port 2000
    calling-number initiator
    service phone videoCapability 1
    system message MKC CME
    url services http://10.10.10.1/voiceview/common/login.do
    url authentication
    http://10.10.10.1/voiceview/authentication/authenticate.do
    time-zone 21
    date-format dd-mm-yy
    voicemail 600
    max-conferences 8 gain -6
    call-forward pattern .T
    call-forward system redirecting-expanded
    moh music-on-hold.au
    web admin system name admin secret 0 test
    dn-webedit
    time-webedit
    transfer-system full-consult dss
    transfer-pattern 9.T
    secondary-dialtone 9
    create cnf-files
    ephone-dn 1 dual-line
    number 201
    label 201
    description Sarah
    name Sarah
    ephone-dn 2 dual-line
    number 202
    label 202
    description Vitthal
    name User2 Vitthal
    ephone-dn 3 dual-line
    number 203 secondary
    label 203
    description Neil
    name User3 Neil
    ephone 1
    video
    username "user1" password 201
    mac-address 0018.18EE.947F
    type 7961 addon 1 7914
    button 1:1
    ephone 2
    video
    username "user2" password 202
    mac-address 0018.18BB.B973
    type 7941
    button 1:2
    ephone 3
    video
    username "user3" password 203
    mac-address 0018.1885.6BA2
    type 7970
    button 1:3

    Hi
    Please find enclosed debug attachment for voice ccapi and ephone. First, I called from outside. Extension 202 rings but when I answered on extension 202 nothing happens. Replace the rceiever and the pone starts ringing again.Second step. I tried to call out by dialing 9 and then number but after a while phone displays unknown number.
    Thank you for your help.
    Vitthal

  • Trouble with connecting my photosmart plus b209a

    trouble with connecting my photosmart plus b209a ........it was conncected to my network until today i was messing around with it and reset the network default by accident,  and now i am trying to connect the printer to my router and it says it doesnt see any connection and ive tried reseting the router bunch of times, and then for a brief minute it said it was connected to ssid hpsetup? and communication mode adhoc?.. not really sure what that was so i reset the network on the printer again back to default and i dont really know what to do it just says no connection found, does anyone have an idea of what i should do and whats wrong

    Hi joey12293,
    I am linking a document that has very good information about how to install the printer to the network.  Click Here  See if this helps.  Let me know how it goes.
    Good Luck !
    Also, remember a click on the Kudos star to the left is a quick "Thanks" for a helpful post.
    Please select the "Accept as Solution" button on the post that best answers your question.
    I appreciate your input ! ___________________________________ _____
    Thank You,
    Rich
    Expert

  • Trouble With Port Mirroring (SG200-08)

    Trouble with port mirroring.
    Even though both Tx and Rx is specified, only getting half the conversation.  Ping reply only for instance.  And when pinging from other locations no traffic at all.
    Please help
    SG200-008
    FW Version: 1.0.2.0
    Boot Version D.3.1
    Thanks

    I also have problem with the mirroring of port on my SG200-08.  The firmware is 1.0.6.2.
    I mirror the port g1, to which my router to the Internet is connected, to the port g2 to be able to see the traffic with a Centos system running Bandwidthd connected to the port g2.  The problem is that I only see the traffic coming in (downloads from the Internet) and not the traffic comming out (uploads to the Internet).
    When looking at the SG 200-08 on the web interface at "Status and Statistics/Interface" and looking at the port g2, I see values for the "Transmit Statistics", but all the values are at 0 for the "Received Statisticsc" (see the attached file)
    I confirmed that in "Administration/Diagnostic/Port Mirroring" is set up both Tx and Rx (it does not work either if I have Tx or Rx alone: I do not see the uploda traffic to the Internet). See the attached file.
    This is very annoying as I purchased this SG 200-08 especially for this and it does not do the job porperly.
    Does anybody knows a solution to this?

  • Trouble with Exported .pdf Files

    I created three 20"x30" one-page documents (with iPhoto-sourced images) which saved as 24.7 MB, 19.4 MB, and 10.7 MB files, respectively. I needed to send JPEG files to my service provider for high-resolution prints. Since Pages '08 doesn't have a JPEG-export option, I exported each of them as .pdf files. My plan was to open the .pdf files in Photoshop and save them down as .jpg files. The same path had worked fine with a fourth Pages '08 layout of a 2.25"x3.75" document. With the three 20"x30" files, however, I ran into trouble.
    My laptop didn't have enough memory to open the exported .pdf files in Photoshop Elements without suffering some image gray-out. I didn't think that was a problem until we discovered that my service provider couldn't open the files at all (running the current Photoshop on a souped-up system). Arghhh.
    I switched to a service provider who can print straight from the .pdf files, but that also brought trouble. Though I could open the files easily in Acrobat 5.0, and they looked great, the service provider (running the current full version of Acrobat) could not open them; all he got was what looked like a blank page.
    I don't think the trouble is related to file size, as the business-card document which sailed through without trouble saved as an 11.2 MB Pages file.
    Could it be sheet size? That's the only thing I can figure. And why would the files open in Acrobat 5.0 without trouble, but not in the current Acrobat (or Acrobat Professional, which we also tried)?
    I ended up "printing" the Pages files as "Save PDF to iPhoto," then exporting the iPhoto image as a maximum-resolution JPEG. The only trouble with that route was that the best I could get was a 200 dpi. When I went through Photoshop (instead of iPhoto) with the business card file, I ended up with a 300 dpi file.
    Am I missing something obvious here? Any help would be appreciated.

    Hi,
    I don't know if this is the correct answer, but you can open a PDF in Preview and save the document as a JPEG and JPEG-2000. I know that Leopard will also have some neat functionality about this as well. You might also want to look at printing as a postscript file rather than a PDF and then open in Photoshop. I talked with a FEDEX/Kinkos employee yesterday about my book at he stated that Macs use 1.5 while Adobe's Acrobat is 1.7. Leopard should also fix this, but it may not help right now.
    HTH

  • Still having trouble with audio on Macbook Pro

    I had posted a discussion board earlier on this issue. I've been having trouble with audio for certain videos on youtube and basically any website embedded with a video. The audio works for a few seconds that doesn't or it doesn't work at all. My volume is up, not on mute, and the one on the video isn't on mute either. It's funny because I just tried watching a video on Firefox (as opposed to Safari) and it works. Could it possible be something with the settings for safari?

    Try restarting your Mac, resetting your router, and resetting your modem. My cable internet has gotten slow at times as well, and when I reset my router everything cleared up.

Maybe you are looking for