Trouble with Airport Extreme Installation

I also posted this on the Emac forum but decided it'd be best to spread the question around.
I just bought an Airport Extreme card 802.11g. I'm following the instructions, but when I turn it on it doesn't connect to a network nor does it even show up in the System Profiler. One thing I noticed is that it doesn't have the plastic pull tab its supposed to have. Does this tab serve a technical purpose or is it just there to make it easier to remove the card?
Thanks in advance and don't be shy to ask for clarifications.
Additionally, I've pulled it out and put it back in several times to no avail. It never has showed up on the System Profiler.
Thanks again

pnigh589, Welcome to the discussion area!
One or more of the following is true:
(1) The card is the incorrect card. Your card should look like this:
(2) The card is installed incorrectly.
(3) The card is defective.
(4) The eMac's motherboard is defective and unable to recognize the card.

Similar Messages

Trouble with airport extreme and express

Hey all. I recently bought a new airport extreme and I'm now having problems setting up a network with the airport express. the airport express that we have is connected to a very old G3 iMac because it doesn't have an airport card and is upstairs. I have so far managed to set up the airport extreme so my G4 iBook and my MacBook Pro are both connected via wireless. The trouble seems to be that I can't get the next step set up as i'm not very experienced with networks and I can't get the express to establish a connection with the extreme. i hope somebody could help me sort out the next step. On a side note, this new airport extreme doesn't allow my xbox 360 to connect to it and i wondered if there is any way I can get it to connect again via wireless, either by changing a setting or the security?
Any help and feedback would be greatly appreciated,
Thanks.

applefan08, Welcome to the discussion area!
To continue to use the AirPort Express (AX) to give Internet access to the iMac G3, you will need to configure the 2 devices to use WDS to wirelessly connect. The instructions start on Page 41 in "Designing AirPort Extreme 802.11n Networks" (http://manuals.info.apple.com/en/DesigningAirPortExtreme802.11nNetworks.pdf).

Trouble with Airport Extreme and Time Capsule

Just got a new 2TB time capsule and added it to my network (existing Airport Express and Airport Extreme). All devices are hard-wire back-hauled to Linksys router. Set up was straight forward with no issues and initiated a time capsule back up without a problem. Within hours I noticed that the TC was no longer reachable in Finder.. Opening the AirPort utility, I saw that both the Extreme and the TC were "lost". Still had (green) internet connectivity, but the base stations were showing as off-line in the Airport utility.
Tried rebooting and checking from multiple other devices and no luck. Occasionally will find them both on-line in Airport utility, but seem to lose one (usually TC) after a short period. All are running the most up to date version of firmware (7.7.3). Prior to installing the TC, I had experienced 0 issues with Airport Express and Extreme.
Has anyone else seen similar issues? Are there settings that need to be accounted for in some way to avoid these frustrating "lost devices"?
thanks

Thank you for your quick answer, smorkerz. However, I did it and it doesn't work.
I tried to check separately the time capsule and the airport extreme, switching one off when using the other one. The result is that each one works alone but when I use them both, just time capsule appears, works well, and I can't use the airport to print for instance.
Do you understand anything ?

Trouble with airport extreme computer-to-computer network

i'm sure this is something pretty obvious, but i recently bought an airport extreme card for my iMac G4 1GHz so as to create a computer-to-computer network with my MacBook Pro.
I set everything up as per http://docs.info.apple.com/article.html?artnum=166640 on my iMac, but when trying to join from my macbook i get "error joining network". Signal level on iMac is fine and the two computers are sitting next to each other.
has anyone any ideas, this is starting to do my head in!!!!
cheers,
stu
iMac G4 1GHz, MacBook Pro 2.16GHz Intel

Can you "see" the new Wireless Network you just created on your iMac from your MacBook Pro?
Did you specify a channel in the range 1-11 that is NOT already in use by a neighboring wireless network? If you have no idea about that, pick a number from 1-11.
For starters, I would NOT use encryption. Get it to work without encryption, then add a 128-bit WEP password.
Try opening Internet Connect on your MacBook Pro to initiate joining your network.

Is anyone successfully using Netgear WN3000RP with Airport Extreme?

Got a brand new WN3000RP wifi range extender. I went through the installation several times myself and several times with tech support to no avail. Tech support told me to return it for a new one.
Everything is connected and the install process goes smoothly but I ultimately cannot ever use the extended network to connect to the Internet. I can see the range extender's mac address on the router but the two devices don't seem to talk to each other.
I'm just wondering if I'm going to have the same problem with a new one or not and wondering if it's even compatible with Airport Extreme routers.
I'm using Airport Utility version 6.1.
Can someone out there can let me know if they got this device working with their Airport Extreme?
Also, what are my other options to extend my range?

I know this answer is likely too late to help but it may help users in the future. In the situation where you are using a range extender there are a few things you need to confirm to make sure it is going to function properly and also some best practices to make sure your network is running smoothly.
1. Is the range extender using the router for DHCP? I have found in my experience is that the router should "reserve" a MAC Address and IP for the the Range Extender. Most times it is 192.168.1.2. I would first set up the router to have the range extender have a set IP Address of 192.168.***.2 and add the MAC Address to the list so that the Range Extender has a Static IP Address in the private network.
2. Initially set the range extender to have an SSID(Wireless Network Name) different than the Router's(Airport) SSID. This will allow you to determine if the Extender is functioning normally without it interfering with your existing network.
3. At this point it is important to set the Range Extender DHCP. What this will do is let the range extender request IP Addresses, DNS(Domain Name Servers), and UPNP Requests. This is where I feel that a lot of people are having issues and assume that the router will still resolve DHCP. If the SSID and Wireless Channel are the same your network will work intermittently with internet access until it is configured correctly.
4. For Devices that will stay on your network such as NAS(Network Storage), Smart TVs, Apple TVs I would recommend setting Static Private IP Addresses for each of them. Such as 192.168.1.3(NAS), 192.168.1.4(Apple TV), 192.168.5(Smart TV). Also if you enter the MAC Address for each device when you set this up it would be recommended.
5. If devices are having issues connecting to internet or certain web services are having issues. It may be necessary to set the Extender(Which is now handling DHCP with IP, DNS, and UPNP passed through from the router) as the Gateway for which device may be having issues. For instance if the Apple TV is having issues communicating on the network(Air Play, Sharing, Streaming) set or configure the network settings manually on the Apple TV. The IP Address would be the one your reserved on your router. The Subnet Mask would likely be 255.255.255.0 by default unless you have changed the amount of potential "Hosts" on your network. The Gateway would be the IP Address of the Extender(Which is paired with your router). DNS servers should be handled automatically. In some situations with certain devices you may need to use a DNS Service for Streaming, but this generally isn't needed.
A Visual Representation would be
ISP>Modem if needed>Router(DHCP Enabled and MAC Addresses Reserved)>Localized Devices<Range Extender(DHCP Enabled and Static IP Address 192.168.***.***)<Apple TV(Manually Configured IP Settings and Range Extender set as Gateway)<Other Devices Localized to Range Extender but not in range of Router(AirPort).
In this representation you should be able to have the router and range extender broadcast Identical SSID and Channels(Radio Frequency). This also allows for advanced settings to be put in place such as LAN networks or Subnets.
An issue that may come up is communicating with the range extender or router while setting up the network. A simple workaround that will allow you to configure either if the network doesn't let you connect on a MacBook is to go to System Preferences>Network>Wifi or Ethernet>Advanced>TCP/IP in configure IPv4>Set Using DHCP with Manual Address> Then IP Address that corresponds with your current network 192.168.***.*** but is not the same as the gateway, router, or reserved devices. This will allow you to connect and configure devices even if router or extender is not assigning IP addresses or operating properly.
Disclaimer* This advice is only for informational purposes with no warranties expressed or implied.

Creating a bridge with airport extreme (base) and airport express

i am having trouble creating a bridge with airport extreme (base) and airport express. i got the airport express to connect to my network. Airtunes sees it fine. i have an iMac (running Tiger) connected to the airport express via ethernet which i was hoping to get internet on (the iMac doesn't not have built in wireless and i had a spare airport express). now the airport express is no longer visible to the airport setup assistant on that iMac. but, like i mentioned, Airtunes is working fine, and the light is green.
i'm new to the wireless stuff. i am sure i just missed a step. how do i get the iMac to connect to the internet via my airport express bridging to my airport extreme wireless network?
your help is appreciated.

You can do this with the equipment you have. Configure the AirPort Extreme base station (AEBS) to act as a WDS main base station and configure the AirPort Express (AX) to act as a WDS remote base station. That will allow you to use the Ethernet port on the AX.
Unfortunately WDS also causes the available wireless bandwidth to be cut in half.

Can't print with Airport Extreme

I am having trouble printing with Airport Extreme.
My printer is connected to the AE but every time I try to print I get a printer offline message.
I have tried in the past to print wirelessly but have given up.
I just bought a new MacBook Pro so I thought I would give it another go.
Thank you.

Not very much to go on here but I'll give it a stab.
Go to the Airport Utility program located in Applications/Utilities folder.
Run this and select "manual setup" for your AE displayed on the left.
Hit the Printers icon on the top. Your shared printer should be displayed here. If it's not, then ensure it's powered on, good usb connection etc.
After this shows a usb printer connected then go to System Preferences>Print & Fax. You'll see printers you have setup before on the left. A green icon usually means they are available. If print doesn't work to the desired printer the best thing to do is remove the previous definitions by highlighting the printer and hitting the "-" icon.
Now hit the "+" sign and define the shared printer. It should be listed in the resulting "add Printer" dialog. Highlight, change any naming info and click "add".
Printer should now be available. I'm assuming a supported printer that have the device drivers loaded on your system.
That's all I got.

Is Internet Explorer incompatible with Airport Extreme for connecting wirelessly to the Internet?

repeat -is Internet Explorer incompatible with Airport Extreme for connecting to the Internet- I am trying to hook up my sister's / Windows 7...HP mini computer to my wireless connection (Airport Extreme to cable /BrightHouse ) all I get is -failed due to 'error 651' -am about to call the jockeys at the cable company to see if they have work-around. Any comment appreciate. Thanks./jimiros

Diane,
I have added very few apps to my G5. The majority of my time is spent editing photos with PhotoshopCS3. I have software updates set to run weekly and have always kept them up to date. I really believe it's a disk permissions issue...but repairing them doesn't help.
*+Upon installation, I used Archive and Install.+* While I agree that Erase and Install may sound like a good idea, it makes me nervous. I do have everything backed up on a bootable CMS drive, but I'm a photographer and was hoping to not have to erase the G5.
Yes, as I mentioned in the original post, I've downloaded and installed the Airport firmware update. And all software is up to date.
All was working just dandy before the upgrade. Unfortunately now it's sounding like I may have to erase my hard drive and install fresh.
If I do that, is it just a matter then of dragging my photos from the backup disk to the G5? And documents? Etc?? The thought of getting all my photos and important information back on the G5 seems a bit staggering.

Can I use my iPad with airport extreme to retrieve files from a USB connected hard drive?

Can I use my iPad with airport extreme to retrieve files from a USB connected hard drive?

Yes, I believe so. Please check out the NetPortal app. I don't have an iPad, but I use it on my iPod Touch to access files on my Time Capsule. It is available from the iTunes App Store.

I'm looking for a list of printers compatible with Airport Extreme

My existing HP printer is not compatible with Airport Extreme and I want to be able to print from all of my Apple devices. I'm looking for a new photo quality printer / scanner / copier which will work wirelessly with all my devices.

Sorry, but there is no "official" list of printers that Apple provides that indicate which are fully functional with the AirPorts. One "unofficial" list has been maintained by iFelix and may be worth taking a look at.

Can I use powerline wireless adapters with airport extreme

can I use power line wireless adapters with airport extreme?

Can this work?
Yes
I read somewhere that powerline adapters are not compatible with Airport.
That information is not correct.
If the AirPort Extreme is already set up as your "main" router, you would connect a short Ethernet cable from one of the LAN <-> ports on the Extreme to the power line adapter.
Locate another adapter in the area where you want to use the AirPort Express and connect a short Ethernet cable from the adapter to the Express.
Configure the Express to "create a wireless network" using the same wireless network name, same security settings and and same password as the AirPort Extreme network and select the Bridge Mode setting for the Express so that it work correctly on the network.

What printers are compatible with airport extreme

What printers are compatible with Airport Extreme so my PC, I-Phone and I-pad can all print wirelessly?
Thanks

You can only use AirPrint-capable printers to print from your devices > http://support.apple.com/kb/ht4356

Scanning with Airport Extreme

Just set up my new Airport Extreme, printing is working fine but I can not scan. Is scanning supported with Airport Extreme?
MacBook Pro Mac OS X (10.4.9)

from looking through the discussion forum more closely I found that is probably the issue...printing only and no scanning. A bit of a disappointment as I do a fair share of scanning. Seem interesting to have to wire-up for a function when wireless is so convenient.
Anyone think that this will change?

Trouble with completing the installation

hi there.
i am having trouble with completing the installation process of iTunes 7.0.2. i get to the part where status says "Registering Modules" and it stops there. i leave the program on and untouched for 30 minutes and the installation is still not complete. this totally screws up my computer and makes it unable for me to open iTunes at all. i have unistalled my old iPod softwear (i lost the thing anyhow) and there is no change. please help me i am at the end of my rope and i dont know what to do

i am having trouble with completing the installation process of iTunes 7.0.2. i get to the part where status says "Registering Modules"
this document is the best place to start with one of those:
iTunes 7 or later for Windows Installation stops responding while "registering modules"
... but if no joy there, and you have SpyCatcher (or the version of Ghostsurf Platinum that contains SpyCatcher) on that PC, try uninstalling SpyCatcher altogether prior to the iTunes install.
if the itunes install goes through properly after that, launch itunes at least once prior to reinstalling SpyCatcher.

What wireless adapters are compatible with Airport Extreme?

What third party wireless adapters are compatible with Airport Extreme?

I would suggest checking out some of the wireless USB adapters provided by Other World Computing (OWC). They have a number of models to choose from. The link is to just one of their offerings.

Trouble with Airport Extreme Installation

Similar Messages

Maybe you are looking for