Trouble with front panel adapto

Hi, I have a Sound Blaster Audigy (SB0090) and my front panel were connected to the motherboard because of the on-board sound card. I disconnected it from the mobo and reconnected it right in the sound card (it's the male connector from this picture: http://www.frontx.com/cpx57p2.gif). Ok, now that it's plugged in, my sound works perfect except that when I connect my headphones in the front panel, the sound keeps going to the speakers and not the headphones.
I'd like some help with this issue. Thanks.

KingAlex,
There has been a lot of discussion about connecting SoundBlaster cards to the front case. A search of the forums for e.g., "front panel headphones" will bring up a long list of messages. This thread will get you started. I don't recommend any of the hacks because if done improperly, they might damage your card. The simplest and safest method is to plug into the rear LineOut/Headphone jack and route this inside the case to the front panel through an unused open card slot. Use a stereo Y-splitter if you also want to connect speakers.

Similar Messages

Trouble with accordion panel

I'm trying to put an accordion panel in a page of the website i'm creating but i've a weird problem.
First of all, this is the link of the page
http://wwwipiniriolotermeit01.businesscatalyst.com/menù.html
As you can see, when i choose one of the option of the panel, the background begin to shake.
Of course i've tried with other panels, included muse's widget but the results is the same.
Can someone help me to resolve this issue?
Thanks in advance.

Thank you very much again.
Last time i've uncheck only the element of the master page's footer not the
entire "menu" page from the menù.
Now, as you say, the jittering is disappear.
Regards
Luca
2014-03-07 16:18 GMT+01:00 Aishvarya Raj Rastogi <[email protected]>:
Re: Trouble with accordion panel created by Aishvarya Raj Rastogi<http://forums.adobe.com/people/aishvarya+rastogi>in *Help
with using Adobe Muse CC* - View the full discussion<http://forums.adobe.com/message/6188378#6188378

Building dll with front panel

Hi all,
do you know, can i build with LV Builder dll that will run with Front Panel open when i call it from some another VI?
I tried build it, but not succesfully.
The prolem was that if i select in VI properties "Show FP when loaded", dll runs with FP open, but property "Show FP when called" doesn't give same results. Dll runs, but in background.

Nadav,
Did you see this recent post about LabVIEW calling LabVIEW DLLs?

Help with front panel audio on K9N board.

Okay, I admit I'm a bit of a moron with front panel audio but I just can't figure out how to configure this board with my case. Here are the pins:
Case:
Mic In
Mic Bias
SpeakOut L
Return L
SpeakOut R
Return R
Ground
Motherboard:
PIN    SIGNAL      DESCRIPTION
1    PORT 1L      Analog Port 1 -Left channel
2    GND      Ground
3    PORT 1R      Analog Port 1 -Right channel
4    PRESENCE#     Active low signal -signals BIOS that a High Definition Audio dongle is connected to the analog header. PRESENCE# = 0 when a High Definition Audio dongle is connected.
5    PORT 2R      Analog Port 2 -Right channel
6    SENSE1_RETIRN     Jack detection return from frontpanel JACK1
7    SENSE_SEND     Jack detectionsenselinefrom the High Definition Audio CODEC jack detection resistor network
8    KEY      ConnectorKey
9    PORT 2L      Analog Port 2 -Left channel
10    SENSE2_RETIRN     Jack detection return from frontpanel JACK2
I haven't been able to make any sense of the two, so if anyone here can help, I would appreciate it very much.

Quote from: crazy on 09-June-06, 15:51:46
You may tell us more information about your mainboard, please give us the detailed name of your mainboard. :D Then there will be more users could give some suggestions.
Sorry, there aren't that many K9N boards out there, but mine is the K9N Platinum MS7250 Version 1.0. It's the AM2 non-SLI nVidia nForce 570 Chipset model.
Thanks for any help.

Problem with front panel USB connector

Motherboard: MS-6750
I have a problem with my front panel USB connector JUSB2 not working.
I have checked the connection to be sure that it is oriented correctly.
I also made sure that it was enabled in the BIOS.
Still no luck. There is not any voltage on this either.
I see a jumper or pin labeled JGS1 just below the JDLED1...do not know what this is and cannot find it in the manual.
Any ideas on what this is and how I might trouble shoot the USB connector?

Which 6570 MB do you have, if its the K7N2 Delta 2 Platinum and came with the Dled bracket try plugging that into that port on the mainboard and see if those usb ports work as it could be the usb hub itself not working on the front. Hope this helps Dok

Any 5.1 Soundcard with Front Panel working under Win 7 64?

Since i'm finally fed up with my X-Fi Platinum not working in Win7 64 i would like to buy something else.
Sadly Creative seems to be the only firm producing soundcards that can have a simultanious stereo output via the front panel while having he 5.1 setup connected at the back.
So as much as i would like to stick it to Creative. But do they have anything with a frontpanel like the Titanium but working under Win7 64?

Originally Posted by icke
Since i'm finally fed up with my X-Fi Platinum not working in Win7 64 i would like to buy something else.
Sadly Creative seems to be the only firm producing soundcards that can have a simultanious stereo output via the front panel while having he 5.1 setup connected at the back.
So as much as i would like to stick it to Creative. But do they have anything with a frontpanel like the Titanium but working under Win7 64?
Hi,
What driver version are you using now? The one that's on the install CD that's included with the soundcard or the latest driver that's available via Creative Labs download service? Provide more info, otherwise no-one can help you. Anyway, the X-fi Platinum (including the Platinum drive bay) should work in Windows 7 x86 and x64.
Try downloading and installing Daniel_K unofficial driver packs for the X-fi and see which one works the best for you.
Daniel_K unofficial driver pack SB X-Fi Series Support Pack 2.5 (10/25/2011)
Daniel_K unofficial driver pack SB X-Fi Series AuzenUAA Pack 1.8 (10/25/2011)
Daniel_K unofficial driver pack SB X-Fi Series AuzenWDM Pack 1.8 (10/25/2011)
Uninstall the old X-fi drivers first and then use "Driver Sweeper" in Windows Safe mode to wipe X-fi drivers that are still left in the Windows OS. Make sure you create a restore point in Windows 7 first, so you can roll-back if something goes wrong.
Good luck!

HP Pavillion HPE-510f, Windows 7, 64 bit with front panel A/V RCA inputs

When i connect devices thru the AV inputs on the front panel, I cannot find an application that recognizes the device. For example, JVC Camcorder so i can playback or just playing music thru these inputs. Is there a driver that needs installling?

Hi Hodgewaco,
As indicated in the title, the front A/V RCA and s-video are input ports. To use those ports with your videocam you are going to need a capture program. ROXIO has commercial programs that should work with those input ports but check with ROXIO Sales. Usually ROXIO has a 30 trial period so if you are not satisfied the your can get a refund. Be sure to inform ROXIO about the exact model of camera that you are using, the output connection type and the format of the video stream.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Audigy SE: Possibility to connect with front panel audio in/

I have a case which has an audio in and out jack on the frontcase. Is it possible to connect these with an connector on the Audigy SE?

Quote from: msiAMD6400 on 25-December-07, 21:57:43
My "disable front panel detection" is unchecked.
It is not clear to me if you were able to check (enable) the box. The setting you need is "disable front panel detection" checked; that means the motherboard delivers the output to front panel, irrespective of there is a headphone connected or not.
If you are unable to check that box, i am not sure where is the problem. If you can, i expect you see a pop up window asking you what you have connected to the front panel, by default it should be an audio output option like headphone. Make sure, as I mentioned already, that you can see inside the audio software window the status of all the audio input/output sockets in different colours. The 2 icons representing the frontpanel should be highlighted and you should be able to designate what output/input you want from each of them. If this doesn't happen there is no point in connecting the audio out cable to the header (unless you have the appropriate MSI frontpanel cable which provides jack detection)
If you have successfully disabled the detection, you just need 3 wires to get output (things work when they are simple). Forget about the looping; you don't need them if jack detection is disabled.
I suggest you connect the 3 wires to the pins as shown in the manual.
Note the pin configuration diagram for the "JAUD1" header. I think the common/ground wire from your headphone socket should be to pin 2, Right out to pin 5 and left out to pin 9.
Let us know of your results.
Siby

Trouble with Update Panel in Chrome browser

Hi.
I work with update panel.
<asp:UpdatePanel runat="server" ID="someid" >
<ContentTemplate>
</ContentTemplate>
<Triggers>
<asp:AsyncPostBackTrigger ControlID="someid2" EventName="somefunction" />
</Triggers>
</asp:UpdatePanel>
In IE all working fine. In Chrome and Firefox after ~30 seconds if i tried to clicked any button the postback is done and page will reset.
How to fix it?

Hi,
Do you want to use the update panel on application page or user control in SharePoint 2013?
If that is the case, here is a similar thread for you to take a look at:
https://social.technet.microsoft.com/Forums/office/en-US/c33d4a46-87d6-4dbc-a24c-cb8e5f9eb1ea/page-refresh-after-postback-from-updatepanel-in-sharepoint-2013
If not, I suggest you post it to ASP.NET Forum, you will get more help and confirmed answers from there.
Best Regards
Dennis Guo
TechNet Community Support

Problems with front panel audio input on hp media center pc

I can't get the audio input phono jacks on the pc front panel to work. Am trying to transfer audio casstettes to my pc. Cassette player works fine.
This question was solved.
View Solution.

Please provide the model number or product number of your system to support you further...
I am an HP employee.
Regards,
Vidya
Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
***Click on "Thumbs up" button to the bottom right side of my post to say thanks!***

I have the iPhone 4 AT&t trouble with front cam

I bought my iPhone 4 unlocked AT&T 16gb phone from a friend. Ever since I gotten my phone the front facing cam never worked. If never worked when my friend had it as well. I do have a piece broken off on the top left corner of my phone that was there when I bought it. I didn't think I would use the front cam but I want too. So basically when I switch to the front cam the shutter is closed and it stays stuck like that and on the bottom to switch from cam to video shakes. Does this happen cause the front cam needs to be replaced or does the hardware need to be replaced? Or is it a short to te front cam? I've never opened my phone, don't know how to, don't have the tools and don't know where to begin. Should I bring it to apple and have them check it out or should I pay $50 and just have the cam replaced and my front screen? I am new to iPhone I've had it for 2 months and still learning the terms etc etc. PLEASE HELP I WANT MY FRONT CAM!!!!!

If the "cell repair shop" you bought it from attempted any sort of hardware repair, Apple will no longer provide any support for it and you'll have to have an unauthorized shop attempt further repairs. If the shop didn't open the iPhone, then Apple will replace the iPhone for their standard fee, which while it will be significantly more than $50 would guarantee you a completely working iPhone for at least 90 days (the lenght of warranty on any out-of-warranty replacement). Or you can have some unauthorized shop attempt to repair the camera and hope they don't mess up anything else (something all too common).
It's up to you how you wish to proceed from here.
Regards.

Having trouble with flash and linking to Sliding panels - PLEASE help

Having trouble with Sliding panels and flash. Otherwise everything works fine but when I'm trying to implement the link
<a href="#" onclick="sp1.showPanel('panel1'); return false;">Panel1</a>
to a flash button I get confused. I have tried following
on (press) {
getURL("javascript:sp1.showPanel('panel1');");
and it did not work. What would you suggest? I am desperate. Please help me! Any suggestions are highly appreciated!!!!

Thanks for your answer!
I have tried both sp1.ShowPanel('panel1'); and window.sp1.ShowPanel('panel1'); they both give blank window with [object]
I have found a solution that works in other browsers, but not in IE. Well basicly it works, but after a few clicks IE freezes.
on (press) {
getURL("javascript:sp1.showPanel('panel1'); void(0);");
Would you happen to have a solution other than that? I believe that the void(0); causes the IE to freeze.

Using Front Panel Composite Video 2 RCA Jack on the HP m8000 Media Center PC

I have a HP M8000 Computer with front panel RCA jacks, composite video 2 and Left and Right Audio RCA jacks. I have been unable to determine how to select these jacks for inputting video recordings to the computer. Any ideas on how to use these jacks to input video from my VCR?

The front composite video jacks did not have software support for the release of this PC. The analog video software was not compatible with Windoze-Vista so there was no software given with this PC model that supported analog video input.

Connect a front panel hea

I have audio jacks on the front of my computer case with a cable that says HD Audio and AC '97.
I don't know where to put the cables into.
I have the Xi-Fi Xtreme Gamer Fatality Pro.
Wow... so I've done some searching and it appears this card does not come with front panel connectors, but the cheaper Xtreme Gamer card does. Is this true?
I don't want to have to mod any cables... just plug and play.
Message Edited by homefry on 03-22-2008 0:6 PM

Yes it does,
http://c.neweggimages.com/NeweggImage/productimage/29-02-005-03.jpg
The one labelled "Creative proprietary connector" is the same as the one shown on this Audigy 2 ZS,
http://audigy2zshowto.blogspot.com/
and I believe the pinouts are the same as well.

SB Z (HD_AUDIO) to old X-Fi Fata1ity front panel I/O (AD_EXT) ???

I upgraded from X-Fi Fatal1ty Edition FPS with front panel I/O to Sound Blaster Z.
Is it possible to connect the Sound Blaster Z to the old I/O panel?
I'm not able to find a pre-made modded AD_EXT cable to connect to the Sound Blaster Z's HD_AUDIO pins.

Hi,
It could be a loose connection somewhere. You might want to double check all connections and reconnect the cables again. If you have not already, please get in touch with support for further assistance.

Trouble with front panel adapto

Similar Messages

Maybe you are looking for